Abstract: This paper describes a finite-difference time-domainFDTD) method to analyze lightning surge propagation in electric transmission lines. Numerical computation of solving the Telegraphist-s equations is determined and investigated its effectiveness. A source of lightning surge wave on power transmission lines is modeled by using Heidler-s surge model. The
proposed method was tested against medium-voltage power
transmission lines in comparison with the solution obtained by using
lattice diagram. As a result, the calculation showed that the method is one of accurate methods to analyze transient
lightning wave in power transmission lines.
Abstract: The paper provides biomasses characteristics by
proximate analysis (volatile matter, fixed carbon and ash) and
ultimate analysis (carbon, hydrogen, nitrogen and oxygen) for the
prediction of the heating value equations. The heating value
estimation of various biomasses can be used as an energy evaluation.
Thirteen types of biomass were studied. Proximate analysis was
investigated by mass loss method and infrared moisture analyzer.
Ultimate analysis was analyzed by CHNO analyzer. The heating
values varied from 15 to 22.4MJ kg-1. Correlations of the calculated
heating value with proximate and ultimate analyses were undertaken
using multiple regression analysis and summarized into three and two
equations, respectively. Correlations based on proximate analysis
illustrated that deviation of calculated heating values from
experimental heating values was higher than the correlations based
on ultimate analysis.
Abstract: In this paper, we discuss convergence of the extrapolated iterative methods for linear systems with the coefficient matrices are singular H-matrices. And we present the sufficient and necessary conditions for convergence of the extrapolated iterative methods. Moreover, we apply the results to the GMAOR methods. Finally, we give one numerical example.
Abstract: The main objective of our study is to collect data
about the profile of the asthmatic patients in Assam and thereby have
a comprehensive knowledge of the factors influencing the asthmatic
patients of the state and their medication pattern. We developed a
search strategy to find any publication about the community based
survey asthma related and used. These to search the MEDLINE
(1996 to current literature) CINAHL DOAJ pubmed databases using
the key phrases, Asthma, Respiratory disorders, Drug therapy of
Asthma, database decision support system and asthma. The
appropriate literature was printed out from the online source and
library (Journal) source. The study was conducted through a set of
structured and non-structured questionnaires targeted on the
asthmatic patients belonging to the rural and urban areas of Assam,
during the month of Dec 2006 to July 2007, 138 cases were studied
in Gauwathi Medical College & Hospital located in Bhangagarh,
Assam in India. The demographic characteristics a factor in 138
patients with asthma with allergic rhinitis (cases) gives the detail
profile of asthmatic patient-s distribution of Assam as classified on
the basis of age and sex. It is evident from the study that male
populations (66%) are more prone to asthma as compared to the
females (34%).Another striking features that emerged from this
survey is the maximum prevalence of asthma in the age group of 20-
30 years followed by infants belonging to the age group of 7 (0.05%)
0-10years among both male and female populations of Assam. The
high incidence of asthma in the age group of 20-30 years may
probably be due to the allergy arising out of sudden exposure to dust
and pollen which the children face while playing and going to the
school. The rural females in the age group of 30-40 years are more
prone to asthma than urban females in the same age group may be
due to sex differentiation among the tribal population of the state.
Pharmacists should educate the asthmatics how to use inhalers
considering growing menace of asthma in the state. Safer drugs
should be produced in the form of aerosol so that easy administration
by the asthmatic patients and physicians of the state is possible for
curing asthma. The health centers should be more equipped with the
medicines to cure asthma in the state like Assam.
Abstract: The present paper deals with the experimental and
computational study of axial collapse of the aluminum metallic shells
having combined tube-frusta geometry between two parallel plates.
Shells were having bottom two third lengths as frusta and remaining
top one third lengths as tube. Shells were compressed to recognize
their modes of collapse and associated energy absorption capability.
An axisymmetric Finite Element computational model of collapse
process is presented and analysed, using a non-linear FE code
FORGE2. Six noded isoparametric triangular elements were used to
discretize the deforming shell. The material of the shells was
idealized as rigid visco-plastic. To validate the computational model
experimental and computed results of the deformed shapes and their
corresponding load-compression and energy-compression curves
were compared. With the help of the obtained results progress of the
axisymmetric mode of collapse has been presented, analysed and
discussed.
Abstract: The problem of agricultural-soil pollution is closely
linked to the production of ecologically pure foodstuffs and to human health. An important task, therefore, is to rehabilitate agricultural
soils with the help of state-of-the-art biotechnologies, based on the use of metal-accumulating plants. In this work, on the basis of
literature data and the results of prior research from this laboratory, plants were selected for which the growing technology is well
developed and which are widespread locally: sugar sorghum (Sorghum saccharatum), sudangrass (Sorghum sudanense (Piper.)
Stapf.), and sunflower (Helianthus annuus L.). I report on laboratory
experiments designed to study the influence of synthetic indole-3-
acetic acid and the extracellular indole-3-acetic acid released by the
plant-growth-promoting rhizobacterium Azospirillum brasilense Sp245 on growth of and arsenic accumulation by these plants.
Abstract: Power system stability enhancement by simultaneous tuning of a Power System Stabilizer (PSS) and a Static Var Compensator (SVC)-based controller is thoroughly investigated in this paper. The coordination among the proposed damping stabilizers and the SVC internal voltage regulators has also been taken into consideration. The design problem is formulated as an optimization problem with a time-domain simulation-based objective function and Real-Coded Genetic Algorithm (RCGA) is employed to search for optimal controller parameters. The proposed stabilizers are tested on a weakly connected power system with different disturbances and loading conditions. The nonlinear simulation results are presented to show the effectiveness and robustness of the proposed control schemes over a wide range of loading conditions and disturbances. Further, the proposed design approach is found to be robust and improves stability effectively even under small disturbance and unbalanced fault conditions.
Abstract: Surface roughness (Ra) is one of the most important requirements in machining process. In order to obtain better surface roughness, the proper setting of cutting parameters is crucial before the process take place. This research presents the development of mathematical model for surface roughness prediction before milling process in order to evaluate the fitness of machining parameters; spindle speed, feed rate and depth of cut. 84 samples were run in this study by using FANUC CNC Milling α-Τ14ιE. Those samples were randomly divided into two data sets- the training sets (m=60) and testing sets(m=24). ANOVA analysis showed that at least one of the population regression coefficients was not zero. Multiple Regression Method was used to determine the correlation between a criterion variable and a combination of predictor variables. It was established that the surface roughness is most influenced by the feed rate. By using Multiple Regression Method equation, the average percentage deviation of the testing set was 9.8% and 9.7% for training data set. This showed that the statistical model could predict the surface roughness with about 90.2% accuracy of the testing data set and 90.3% accuracy of the training data set.
Abstract: Mechanical buckling analysis of rectangular plates
with central circular cutout is performed in this paper. The finiteelement
method is used to study the effects of plate-support
conditions, aspect ratio, and hole size on the mechanical buckling
strength of the perforated plates subjected to linearly varying loading.
Results show that increasing the hole size does not necessarily reduce
the mechanical buckling strength of the perforated plates. It is also
concluded that the clamped boundary condition increases the
mechanical buckling strength of the perforated plates more than the
simply-supported boundary condition and the free boundary
conditions enhance the mechanical buckling strength of the
perforated plates more effectively than the fixed boundary conditions.
Furthermore, for the bending cases, the critical buckling load of
perforated plates with free edges is less than perforated plates with
fixed edges.
Abstract: Artificial Neural Network (ANN)s are best suited for
prediction and optimization problems. Trained ANNs have found
wide spread acceptance in several antenna design systems. Four
parameters namely antenna radiation resistance, loss resistance, efficiency,
and inductance can be used to design an antenna layout though
there are several other parameters available. An ANN can be trained
to provide the best and worst case precisions of an antenna design
problem defined by these four parameters. This work describes the
use of an ANN to generate the four mentioned parameters for a loop
antenna for the specified frequency range. It also provides insights
to the prediction of best and worst-case design problems observed
in applications and thereby formulate a model for physical layout
design of a loop antenna.
Abstract: A novel low-cost impedance control structure is
proposed for monitoring the contact force between end-effector and
environment without installing an expensive force/torque sensor.
Theoretically, the end-effector contact force can be estimated from the
superposition of each joint control torque. There have a nonlinear
matrix mapping function between each joint motor control input and
end-effector actuating force/torques vector. This new force control
structure can be implemented based on this estimated mapping matrix.
First, the robot end-effector is manipulated to specified positions, then
the force controller is actuated based on the hall sensor current
feedback of each joint motor. The model-free fuzzy sliding mode
control (FSMC) strategy is employed to design the position and force
controllers, respectively. All the hardware circuits and software
control programs are designed on an Altera Nios II embedded
development kit to constitute an embedded system structure for a
retrofitted Mitsubishi 5 DOF robot. Experimental results show that PI
and FSMC force control algorithms can achieve reasonable contact
force monitoring objective based on this hardware control structure.
Abstract: As the air traffic increases at a hub airport, some
flights cannot land or depart at their preferred target time. This event
happens because the airport runways become occupied to near their
capacity. It results in extra costs for both passengers and airlines
because of the loss of connecting flights or more waiting, more fuel
consumption, rescheduling crew members, etc. Hence, devising an
appropriate scheduling method that determines a suitable runway and
time for each flight in order to efficiently use the hub capacity and
minimize the related costs is of great importance. In this paper, we
present a mixed-integer zero-one model for scheduling a set of mixed
landing and departing flights (despite of most previous studies
considered only landings). According to the fact that the flight cost is
strongly affected by the level of airline, we consider different airline
categories in our model. This model presents a single objective
minimizing the total sum of three terms, namely 1) the weighted
deviation from targets, 2) the scheduled time of the last flight (i.e.,
makespan), and 3) the unbalancing the workload on runways. We
solve 10 simulated instances of different sizes up to 30 flights and 4
runways. Optimal solutions are obtained in a reasonable time, which
are satisfactory in comparison with the traditional rule, namely First-
Come-First-Serve (FCFS) that is far apart from optimality in most
cases.
Abstract: Because of the low maintenance and robustness induction motors have many applications in the industries. The speed control of induction motor is more important to achieve maximum torque and efficiency. Various speed control techniques like, Direct Torque Control, Sensorless Vector Control and Field Oriented Control are discussed in this paper. Soft computing technique – Fuzzy logic is applied in this paper for the speed control of induction motor to achieve maximum torque with minimum loss. The fuzzy logic controller is implemented using the Field Oriented Control technique as it provides better control of motor torque with high dynamic performance. The motor model is designed and membership functions are chosen according to the parameters of the motor model. The simulated design is tested using various tool boxes in MATLAB. The result concludes that the efficiency and reliability of the proposed speed controller is good.
Abstract: Copolymerization of ethylene with 1-hexene was
carried out using two ansa-fluorenyl titanium derivative complexes.
The substituent effect on the catalytic activity, monomer reactivity
ratio and polymer property was investigated. It was found that the
presence of t-Bu groups on fluorenyl ring exhibited remarkable
catalytic activity and produced polymer with high molecular weight.
However, these catalysts produce polymer with narrow molecular
weight distribution, indicating the characteristic of single-site
metallocene catalyst. Based on 13C NMR, we can observe that
monomer reactivity ratio was affected by catalyst structure. The rH
values of complex 2 were lower than that of complex 1 which might
be result from the higher steric hindrance leading to a reduction of 1-
hexene insertion step.
Abstract: Time series forecasting is an important and widely
popular topic in the research of system modeling. This paper
describes how to use the hybrid PSO-RLSE neuro-fuzzy learning
approach to the problem of time series forecasting. The PSO
algorithm is used to update the premise parameters of the
proposed prediction system, and the RLSE is used to update the
consequence parameters. Thanks to the hybrid learning (HL)
approach for the neuro-fuzzy system, the prediction performance
is excellent and the speed of learning convergence is much faster
than other compared approaches. In the experiments, we use the
well-known Mackey-Glass chaos time series. According to the
experimental results, the prediction performance and accuracy in
time series forecasting by the proposed approach is much better
than other compared approaches, as shown in Table IV. Excellent
prediction performance by the proposed approach has been
observed.
Abstract: The main objective of this study was to remove and recover Ni, Cu and Fe from a mixed metal system using sodium hypophosphite as a reducing agent and nickel powder as seeding material. The metal systems studied consisted of Ni-Cu, Ni-Fe and Ni-Cu-Fe solutions. A 5 L batch reactor was used to conduct experiments where 100 mg/l of each respective metal was used. It was found that the metals were reduced to their elemental form with removal efficiencies of over 80%. The removal efficiency decreased in the order Fe>Ni>Cu. The metal powder obtained contained between 97-99% Ni and was almost spherical and porous. Size enlargement by aggregation was the dominant particulate process.
Abstract: Cardiovascular diseases, principally atherosclerosis, are responsible for 30% of world deaths. Atherosclerosis is due to the formation of plaque. The fatty plaque may be at risk of rupture, leading typically to stroke and heart attack. The plaque is usually associated with a high degree of lumen reduction, called a stenosis.It is increasingly recognized that the initiation and progression of disease and the occurrence of clinical events is a complex interplay between the local biomechanical environment and the local vascular biology. The aim of this study is to investigate the flow behavior through a stenosed artery. A physical experiment was performed using an artery model and blood analogue fluid. An axisymmetric model constructed consists of contraction and expansion region that follow a mathematical form of cosine function. A 30% diameter reduction was used in this study. The flow field was measured using particle image velocimetry (PIV). Spherical particles with 20μm diameter were seeded in a water-glycerol-NaCl mixture. Steady flow Reynolds numbers are 250. The area of interest is the region after the stenosis where the flow separation occurs. The velocity field was measured and the velocity gradient was investigated. There was high particle concentration in the recirculation zone. High velocity gradient formed immediately after the stenosis throat created a lift force that enhanced particle migration to the flow separation area.
Abstract: Static analysis of source code is used for auditing web
applications to detect the vulnerabilities. In this paper, we propose a
new algorithm to analyze the PHP source code for detecting LFI and
RFI potential vulnerabilities. In our approach, we first define some
patterns for finding some functions which have potential to be abused
because of unhandled user inputs. More precisely, we use regular
expression as a fast and simple method to define some patterns for
detection of vulnerabilities. As inclusion functions could be also used
in a safe way, there could occur many false positives (FP). The first
cause of these FP-s could be that the function does not use a usersupplied
variable as an argument. So, we extract a list of usersupplied
variables to be used for detecting vulnerable lines of code.
On the other side, as vulnerability could spread among the variables
like by multi-level assignment, we also try to extract the hidden usersupplied
variables. We use the resulted list to decrease the false
positives of our method. Finally, as there exist some ways to prevent
the vulnerability of inclusion functions, we define also some patterns
to detect them and decrease our false positives.
Abstract: Responses of the dynamical systems are highly affected by the natural frequencies and it has a huge impact on design and operation of high-rise and high-speed elevators. In the present paper, the variational iteration method (VIM) is employed to investigate better understanding the dynamics of elevator cable as a single-degree-of-freedom (SDOF) swing system. Comparisons made among the results of the proposed closed-form analytical solution, the traditional numerical iterative time integration solution, and the linearized governing equations confirm the accuracy and efficiency of the proposed approach. Furthermore, based on the results of the proposed closed-form solution, the linearization errors in calculating the natural frequencies in different cases are discussed.
Abstract: This research was conducted to determine responses
of chickpeas to drought in different periods (early period, late period,
no-irrigation, two times irrigation as control). The trial was made in
“Randomized Complete Block Design" with three replications on
2010 and 2011 years in Konya-Turkey. Genotypes were consisted
from 7 lines of ICARDA, 2 certified lines and 1 local population. The
results showed that; as means of years and genotypes, early period
stress showed highest (207.47 kg da-1) seed yield and it was followed
by control (202.33 kg da-1), late period (144.64 kg da-1) and normal
(106.93 kg da-1) stress applications. The genotypes were affected too
much by drought and, the lowest seed was taken from non-irrigated
plots. As the means of years and stress applications, the highest
(196.01 kg da-1) yield was taken from genotype 22255. The reason of
yield variation could be derived from different responses of
genotypes to drought.