Abstract: Internal combustion engines rejects 30-40% of the
energy supplied by fuel to the environment through exhaust gas. thus, there is a possibility for further significant improvement of efficiency with the utilization of exhaust gas energy and its conversion to mechanical energy or electrical energy. The Thermo-Electric
Generator (TEG) will be located in the exhaust system and will make use of an energy flow between the warmer exhaust gas and the external environment. Predict to th optimum position of temperature
distribution and the performance of TEG through numerical analysis.
The experimental results obtained show that the power output significantly increases with the temperature difference between cold
and hot sides of a thermoelectric generator.
Abstract: Using a set of confidence intervals, we develop a
common approach, to construct a fuzzy set as an estimator for
unknown parameters in statistical models. We investigate a method
to derive the explicit and unique membership function of such fuzzy
estimators. The proposed method has been used to derive the fuzzy
estimators of the parameters of a Normal distribution and some
functions of parameters of two Normal distributions, as well as the
parameters of the Exponential and Poisson distributions.
Abstract: The indoor airflow with a mixed natural/forced convection
was numerically calculated using the laminar and turbulent
approach. The Boussinesq approximation was considered for a simplification
of the mathematical model and calculations. The results
obtained, such as mean velocity fields, were successfully compared
with experimental PIV flow visualizations. The effect of the distance
between the cooled wall and the heat exchanger on the temperature
and velocity distributions was calculated. In a room with a simple
shape, the computational code OpenFOAM demonstrated an ability to
numerically predict flow patterns. Furthermore, numerical techniques,
boundary type conditions and the computational grid quality were
examined. Calculations using the turbulence model k-omega had a
significant effect on the results influencing temperature and velocity
distributions.
Abstract: This paper presents a simple approach for load
flow analysis of a radial distribution network. The proposed
approach utilizes forward and backward sweep algorithm
based on Kirchoff-s current law (KCL) and Kirchoff-s voltage
law (KVL) for evaluating the node voltages iteratively. In this
approach, computation of branch current depends only on the
current injected at the neighbouring node and the current in
the adjacent branch. This approach starts from the end nodes
of sub lateral line, lateral line and main line and moves
towards the root node during branch current computation. The
node voltage evaluation begins from the root node and moves
towards the nodes located at the far end of the main, lateral
and sub lateral lines. The proposed approach has been tested
using four radial distribution systems of different size and
configuration and found to be computationally efficient.
Abstract: An effective approach for unbalanced three-phase
distribution power flow solutions is proposed in this paper. The
special topological characteristics of distribution networks have been
fully utilized to make the direct solution possible. Two matrices–the
bus-injection to branch-current matrix and the branch-current to busvoltage
matrix– and a simple matrix multiplication are used to
obtain power flow solutions. Due to the distinctive solution
techniques of the proposed method, the time-consuming LU
decomposition and forward/backward substitution of the Jacobian
matrix or admittance matrix required in the traditional power flow
methods are no longer necessary. Therefore, the proposed method is
robust and time-efficient. Test results demonstrate the validity of the
proposed method. The proposed method shows great potential to be
used in distribution automation applications.
Abstract: Constant upgrading of Enterprise Resource Planning
(ERP) systems is necessary, but can cause new defects. This paper
attempts to model the likelihood of defects after completed upgrades
with Weibull defect probability density function (PDF). A case study
is presented analyzing data of recorded defects obtained for one ERP
subsystem. The trends are observed for the value of the parameters
relevant to the proposed statistical Weibull distribution for a given
one year period. As a result, the ability to predict the appearance of
defects after the next upgrade is described.
Abstract: The aim of this study was to investigate the influence
of reaction temperature and wheat straw moisture content on the
pyrolysis product yields, in the temperature range of 475-575 °C.
Samples of straw with moisture contents from 1.5 wt % to 15.0 wt %
were fed to a bench scale Pyrolysis Centrifuge Reactor (PCR). The
experimental results show that the changes in straw moisture content
have no significant effect on the distribution of pyrolysis product
yields. The maximum bio-oil yields approximately 60 (wt %, on dry
ash free feedstock basis) was observed around 525 °C - 550 °C for all
straw moisture levels. The water content in the wet straw bio-oil was
the highest. The heating value of bio-oil and solid char were
measured and the percentages of its energy distribution were
calculated. The energy distributions of bio-oil, char and gas were 56-
69 % 24-33 %, and 2-19 %, respectively.
Abstract: In the present work, the performance of the particle
swarm optimization and the genetic algorithm compared as a typical
geometry design problem. The design maximizes the heat transfer
rate from a given fin volume. The analysis presumes that a linear
temperature distribution along the fin. The fin profile generated using
the B-spline curves and controlled by the change of control point
coordinates. An inverse method applied to find the appropriate fin
geometry yield the linear temperature distribution along the fin
corresponds to optimum design. The numbers of the populations, the
count of iterations and time to convergence measure efficiency.
Results show that the particle swarm optimization is most efficient
for geometry optimization.
Abstract: Mitochondria are dynamic organelles, capable to
interact with each other. While the number of mitochondria in a cell
varies, their quality and functionality depends on the operation of
fusion, fission, motility and mitophagy. Nowadays, several
researches declare as an important factor in neurogenerative diseases
the disruptions in the regulation of mitochondrial dynamics. In this
paper a stochastic model in BioAmbients calculus is presented,
concerning mitochondrial fusion and its distribution in the renewal of
mitochondrial population in a cell. This model describes the
successive and dependent stages of protein synthesis, protein-s
activation and merging of two independent mitochondria.
Abstract: An automated wood recognition system is designed to
classify tropical wood species.The wood features are extracted based
on two feature extractors: Basic Grey Level Aura Matrix (BGLAM)
technique and statistical properties of pores distribution (SPPD)
technique. Due to the nonlinearity of the tropical wood species
separation boundaries, a pre classification stage is proposed which
consists ofKmeans clusteringand kernel discriminant analysis (KDA).
Finally, Linear Discriminant Analysis (LDA) classifier and KNearest
Neighbour (KNN) are implemented for comparison purposes.
The study involves comparison of the system with and without pre
classification using KNN classifier and LDA classifier.The results
show that the inclusion of the pre classification stage has improved
the accuracy of both the LDA and KNN classifiers by more than
12%.
Abstract: In this paper a three dimensional thermal model of a
power toroidal transformer is proposed for both steady-state or
transient conditions. The influence of electric current and ambient
temperature on the temperature distribution, has been investigated.
To validate the three dimensional thermal model, some experimental
tests have been done. There is a good correlation between
experimental and simulation results.
Abstract: EPC Class-1 Generation-2 UHF tags, one of Radio
frequency identification or RFID tag types, is expected that most
companies are planning to use it in the supply chain in the short term
and in consumer packaging in the long term due to its inexpensive
cost. Because of the very cost, however, its resources are extremely
scarce and it is hard to have any valuable security algorithms in it. It
causes security vulnerabilities, in particular cloning the tags for
counterfeits. In this paper, we propose a product authentication
solution for anti-counterfeiting at application level in the supply chain
and mobile RFID environment. It aims to become aware of
distribution of spurious products with fake RFID tags and to provide a
product authentication service to general consumers with mobile
RFID devices like mobile phone or PDA which has a mobile RFID
reader. We will discuss anti-counterfeiting mechanisms which are
required to our proposed solution and address requirements that the
mechanisms should have.
Abstract: Metal matrix composites (MMC) are generating
extensive interest in diverse fields like defense, aerospace, electronics
and automotive industries. In this present investigation, material
removal rate (MRR) modeling has been carried out using an
axisymmetric model of Al-SiC composite during electrical discharge
machining (EDM). A FEA model of single spark EDM was
developed to calculate the temperature distribution.Further, single
spark model was extended to simulate the second discharge. For
multi-discharge machining material removal was calculated by
calculating the number of pulses. Validation of model has been done
by comparing the experimental results obtained under the same
process parameters with the analytical results. A good agreement was
found between the experimental results and the theoretical value.
Abstract: The aim of this paper is to introduce a parametric
distribution model in fatigue life reliability analysis dealing with
variation in material properties. Service loads in terms of responsetime
history signal of Belgian pave were replicated on a multi-axial
spindle coupled road simulator and stress-life method was used to
estimate the fatigue life of automotive stub axle. A PSN curve was
obtained by monotonic tension test and two-parameter Weibull
distribution function was used to acquire the mean life of the
component. A Pearson system was developed to evaluate the fatigue
life reliability by considering stress range intercept and slope of the
PSN curve as random variables. Considering normal distribution of
fatigue strength, it is found that the fatigue life of the stub axle to
have the highest reliability between 10000 – 15000 cycles. Taking
into account the variation of material properties associated with the
size effect, machining and manufacturing conditions, the method
described in this study can be effectively applied in determination of
probability of failure of mass-produced parts.
Abstract: In this paper, the potential use of an exponential
hidden Markov model to model a hidden pavement deterioration
process, i.e. one that is not directly measurable, is investigated. It is
assumed that the evolution of the physical condition, which is the
hidden process, and the evolution of the values of pavement distress
indicators, can be adequately described using discrete condition states
and modeled as a Markov processes. It is also assumed that condition
data can be collected by visual inspections over time and represented
continuously using an exponential distribution. The advantage of
using such a model in decision making process is illustrated through
an empirical study using real world data.
Abstract: The protection issues in distribution systems with open and closed-loop are studied, and a generalized protection setting scheme based on the traditional over current protection theories is proposed to meet the new requirements. The setting method is expected to be easier realized using computer program, so that the on-line adaptive setting for coordination in distribution system can be implemented. An automatic setting program is created and several cases are taken into practice. The setting results are verified by the coordination curves of the protective devices which are plotted using MATLAB.
Abstract: In this paper, based on the past project cost and time
performance, a model for forecasting project cost performance is
developed. This study presents a probabilistic project control concept
to assure an acceptable forecast of project cost performance. In this
concept project activities are classified into sub-groups entitled
control accounts. Then obtain the Stochastic S-Curve (SS-Curve), for
each sub-group and the project SS-Curve is obtained by summing
sub-groups- SS-Curves. In this model, project cost uncertainties are
considered through Beta distribution functions of the project
activities costs required to complete the project at every selected time
sections through project accomplishment, which are extracted from a
variety of sources. Based on this model, after a percentage of the
project progress, the project performance is measured via Earned
Value Management to adjust the primary cost probability distribution
functions. Then, accordingly the future project cost performance is
predicted by using the Monte-Carlo simulation method.
Abstract: In this paper a numerical algorithm is described for solving the boundary value problem associated with axisymmetric, inviscid, incompressible, rotational (and irrotational) flow in order to obtain duct wall shapes from prescribed wall velocity distributions. The governing equations are formulated in terms of the stream function ψ (x,y)and the function φ (x,y)as independent variables where for irrotational flow φ (x,y)can be recognized as the velocity potential function, for rotational flow φ (x,y)ceases being the velocity potential function but does remain orthogonal to the stream lines. A numerical method based on the finite difference scheme on a uniform mesh is employed. The technique described is capable of tackling the so-called inverse problem where the velocity wall distributions are prescribed from which the duct wall shape is calculated, as well as the direct problem where the velocity distribution on the duct walls are calculated from prescribed duct geometries. The two different cases as outlined in this paper are in fact boundary value problems with Neumann and Dirichlet boundary conditions respectively. Even though both approaches are discussed, only numerical results for the case of the Dirichlet boundary conditions are given. A downstream condition is prescribed such that cylindrical flow, that is flow which is independent of the axial coordinate, exists.
Abstract: The main objectives of this paper are to measure
pollutants concentrations in the oil refinery area in Kuwait over three
periods during one year, obtain recent emission inventory for the
three refineries of Kuwait, use AERMOD and the emission inventory
to predict pollutants concentrations and distribution, compare model
predictions against measured data, and perform numerical
experiments to determine conditions at which emission rates and the
resulting pollutant dispersion is below maximum allowable limits.
Abstract: The present study deals with the modeling and simulation of flow through an annular reactor at different hydrodynamic conditions using computational fluid dynamics (CFD) to investigate the flow behavior. CFD modeling was utilized to predict velocity distribution and average velocity in the annular geometry. The results of CFD simulations were compared with the mathematically derived equations and already developed correlations for validation purposes. CFD modeling was found suitable for predicting the flow characteristics in annular geometry under laminar flow conditions. It was observed that CFD also provides local values of the parameters of interest in addition to the average values for the simulated geometry.