Abstract: This paper presents an intelligent speed control
system based on fuzzy logic for a voltage source PWM inverter-fed
indirect vector controlled induction motor drive. Traditional indirect
vector control system of induction motor introduces conventional PI
regulator in outer speed loop; it is proved that the low precision of the
speed regulator debases the performance of the whole system. To
overcome this problem, replacement of PI controller by an intelligent
controller based on fuzzy set theory is proposed. The performance of
the intelligent controller has been investigated through digital
simulation using MATLAB-SIMULINK package for different
operating conditions such as sudden change in reference speed and
load torque. The simulation results demonstrate that the performance
of the proposed controller is better than that of the conventional PI
controller.
Abstract: In this paper, a novel deinterlacing algorithm is
proposed. The proposed algorithm approximates the distribution of the
luminance into a polynomial function. Instead of using one
polynomial function for all pixels, different polynomial functions are
used for the uniform, texture, and directional edge regions. The
function coefficients for each region are computed by matrix
multiplications. Experimental results demonstrate that the proposed
method performs better than the conventional algorithms.
Abstract: In this article, using finite element analysis (FEA)
and an X-ray diffractometer (XRD), cold-sprayed titanium particles
on a steel substrate is investigated in term of cooling time and the
development of residual strains. Three cooling-down models of
sprayed particles after deposition stage are simulated and discussed:
the first model (m1) considers conduction effect to the substrate only,
the second model (m2) considers both conduction as well as
convection effect to the environment, and the third model (m3) which
is the same as the second model but with the substrate heated to a
near particle temperature before spraying. Thereafter, residual strains
developed in the third model is compared with the experimental
measurement of residual strains, which involved a Bruker D8
Advance Diffractometer using CuKa radiation (40kV, 40mA)
monochromatised with a graphite sample monochromator. For
deposition conditions of this study, a good correlation was found to
exist between the FEA results and XRD measurements of residual
strains.
Abstract: Since polymerase chain reaction (PCR) has been
invented, it has emerged as a powerful tool in genetic analysis. The
PCR products are closely linked with thermal cycles. Therefore, to
reduce the reaction time and make temperature distribution uniform in
the reaction chamber, a novel oscillatory thermal cycler is designed.
The sample is placed in a fixed chamber, and three constant isothermal
zones are established and lined in the system. The sample is oscillated
and contacted with three different isothermal zones to complete
thermal cycles. This study presents the design of the geometric
characteristics of the chamber. The commercial software
CFD-ACE+TM is utilized to investigate the influences of various
materials, heating times, chamber volumes, and moving speed of the
chamber on the temperature distributions inside the chamber. The
chamber moves at a specific velocity and the boundary conditions
with time variations are related to the moving speed. Whereas the
chamber moves, the boundary is specified at the conditions of the
convection or the uniform temperature. The user subroutines compiled
by the FORTRAN language are used to make the numerical results
realistically. Results show that the reaction chamber with a rectangular
prism is heated on six faces; the effects of various moving speeds of
the chamber on the temperature distributions are examined. Regarding
to the temperature profiles and the standard deviation of the
temperature at the Y-cut cross section, the non-uniform temperature
inside chamber is found as the moving speed is larger than 0.01 m/s.
By reducing the heating faces to four, the standard deviation of the
temperature of the reaction chamber is under 1.4×10-3K with the range
of velocities between 0.0001 m/s and 1 m/s. The nature convective
boundary conditions are set at all boundaries while the chamber moves
between two heaters, the effects of various moving velocities of the
chamber on the temperature distributions are negligible at the assigned
time duration.
Abstract: We address the problem of joint beamforming and multipath channel parameters estimation in Wideband Code Division Multiple Access (WCDMA) communication systems that employ Multiple-Access Interference (MAI) suppression techniques in the uplink (from mobile to base station). Most of the existing schemes rely on time multiplex a training sequence with the user data. In WCDMA, the channel parameters can also be estimated from a code multiplexed common pilot channel (CPICH) that could be corrupted by strong interference resulting in a bad estimate. In this paper, we present new methods to combine interference suppression together with channel estimation when using multiple receiving antennas by using adaptive signal processing techniques. Computer simulation is used to compare between the proposed methods and the existing conventional estimation techniques.
Abstract: Traffic enforcement units (the Police) are partly
responsible for the severity and frequency of the traffic accidents via
the effectiveness of their safety measures. The Police claims that the
reductions in accidents and their severities occur largely by their
timely interventions at the black spots, through traffic management
or temporary changes in the road design (guiding, reducing speeds
and eliminating sight obstructions, etc.). Yet, some other external
factors than the Police measures may intervene into which such
claims require a statistical confirmation. In order to test the net
impact of the Police contribution in the reduction of the number of
crashes, Chi square test was applied for 25 spots (streets and
intersections) and an average evaluation was achieved for general
conclusion in the case study of Izmir city. Separately, the net impact
of economic crisis in the reduction of crashes is assessed by the
trend analysis for the case of the economic crisis with the probable
reduction effects on the trip generation or modal choice. Finally, it
was proven that the Police measures were effective to some degree as
they claimed, though the economic crisis might have only negligible
contribution to the reductions in the same period observed.
Abstract: This paper presents a solution for ceramic cutting tools availability in interrupted machining. Experiments were performed on a special fixture – the interrupted cut simulator. This fixture was constructed at our Department of Machining and Assembly within the scope of a project by the Czech Science Foundation. The goals of the tests were to contribute to the wider usage of these cutting materials in machining, especially in interrupted machining. Through the centuries, producers of ceramic cutting tools have taken big steps forward. Namely, increasing durability in maintaining high levels of strength and hardness lends an advantage. Some producers of these materials advise cutting inserts for interrupted machining at the present time [1, 2].
Abstract: Twenty seven tektites from the Wenchang area, Hainan
province (south China) and five tektites from the Khon Kaen area
(northeast Thailand) were analyzed for major and trace element
contents and Rb-Sr isotopic compositions. All the samples studied are
splash-form tektites. Tektites of this study are characterized by high
SiO2 contents ranging from 71.95 to 74.07 wt% which is consistent
with previously published analyses of Australasian tektites. The trace
element ratios Ba/Rb (avg. 3.89), Th/Sm (avg. 2.40), Sm/Sc (avg.
0.45), Th/Sc (avg. 0.99) and the rare earth elements (REE) contents of
tektites of this study are similar to the average upper continental crust.
Based on the chemical composition, it is suggested that tektites in this
study are derived from similar parental material and are similar to the
post-Archean upper crustal rocks. The major and trace element
abundances of tektites analyzed indicate that the parental material of
tektites may be a terrestrial sedimentary deposit. The tektites from the
Wenchang area, Hainan Island have high positive εSr(0)
values-ranging from 184.5~196.5 which indicate that the parental
material for these tektites have similar Sr isotopic compositions to old
terrestrial sedimentary rocks and they were not dominantly derived
from recent young sediments (such as soil or loess). Based on Rb-Sr
isotopic data, it has been suggested by Blum (1992) [1]that the
depositional age of sedimentary target materials is close to 170Ma
(Jurassic). According to the model suggested by Ho and Chen
(1996)[2], mixing calculations for various amounts and combinations
of target rocks have been carried out. We consider that the best fit for
tektites from the Wenchang area is a mixture of 47% shale, 23%
sandstone, 25% greywacke and 5% quartzite, and the other tektites
from Khon Kaen area is a mixture of 46% shale, 2% sandstone, 20%
greywacke and 32% quartzite.
Abstract: Group contribution based models are widely used in
industrial applications for its convenience and flexibility. Although a
number of group contribution models have been proposed, there were
certain limitations inherent to those models. Models based on group
contribution excess Gibbs free energy are limited to low pressures and
models based on equation of state (EOS) cannot properly describe
highly nonideal mixtures including acids without introducing
additional modification such as chemical theory. In the present study
new a new approach derived from quantum chemistry have been used
to calculate necessary EOS group interaction parameters. The
COSMO-RS method, based on quantum mechanics, provides a
reliable tool for fluid phase thermodynamics. Benefits of the group
contribution EOS are the consistent extension to hydrogen-bonded
mixtures and the capability to predict polymer-solvent equilibria up to
high pressures. The authors are confident that with a sufficient
parameter matrix the performance of the lattice EOS can be improved
significantly.
Abstract: Wavelet transforms are multiresolution
decompositions that can be used to analyze signals and images.
Image compression is one of major applications of wavelet
transforms in image processing. It is considered as one of the most
powerful methods that provides a high compression ratio. However,
its implementation is very time-consuming. At the other hand,
parallel computing technologies are an efficient method for image
compression using wavelets. In this paper, we propose a parallel
wavelet compression algorithm based on quadtrees. We implement
the algorithm using MatlabMPI (a parallel, message passing version
of Matlab), and compute its isoefficiency function, and show that it is
scalable. Our experimental results confirm the efficiency of the
algorithm also.
Abstract: Among all mechanical joining processes, welding has
been employed for its advantage in design flexibility, cost saving,
reduced overall weight and enhanced structural performance.
However, for structures made of relatively thin components, welding
can introduce significant buckling distortion which causes loss of
dimensional control, structural integrity and increased fabrication
costs. Different parameters can affect buckling behavior of welded
thin structures such as, heat input, welding sequence, dimension of
structure. In this work, a 3-D thermo elastic-viscoplastic finite
element analysis technique is applied to evaluate the effect of shell
dimensions on buckling behavior and entropy generation of welded
thin shells. Also, in the present work, the approximated longitudinal
transient stresses which produced in each time step, is applied to the
3D-eigenvalue analysis to ratify predicted buckling time and
corresponding eigenmode. Besides, the possibility of buckling
prediction by entropy generation at each time is investigated and it is
found that one can predict time of buckling with drawing entropy
generation versus out of plane deformation. The results of finite
element analysis show that the length, span and thickness of welded
thin shells affect the number of local buckling, mode shape of global
buckling and post-buckling behavior of welded thin shells.
Abstract: This research work proposes a model of network security systems aiming to prevent production system in a data center from being attacked by intrusions. Conceptually, we introduce a decoy system as a part of the security system for luring intrusions, and apply network intrusion detection (NIDS), coupled with the decoy system to perform intrusion prevention. When NIDS detects an activity of intrusions, it will signal a redirection module to redirect all malicious traffics to attack the decoy system instead, and hence the production system is protected and safe. However, in a normal situation, traffic will be simply forwarded to the production system as usual. Furthermore, we assess the performance of the model with various bandwidths, packet sizes and inter-attack intervals (attacking frequencies).
Abstract: Today, the preferences and participation of the TD groups such as the elderly and disabled is still lacking in decision-making of transportation planning, and their reactions to certain type of policies are not well known. Thus, a clear methodology is needed. This study aimed to develop a method to extract the preferences of the disabled to be used in the policy-making stage that can also guide to future estimations. The method utilizes the combination of cluster analysis and data filtering using the data of the Arao city (Japan). The method is a process that follows: defining the TD group by the cluster analysis tool, their travel preferences in tabular form from the household surveys by policy variableimpact pairs, zones, and by trip purposes, and the final outcome is the preference probabilities of the disabled. The preferences vary by trip purpose; for the work trips, accessibility and transit system quality policies with the accompanying impacts of modal shifts towards public mode use as well as the decreasing travel costs, and the trip rate increase; for the social trips, the same accessibility and transit system policies leading to the same mode shift impact, together with the travel quality policy area leading to trip rate increase. These results explain the policies to focus and can be used in scenario generation in models, or any other planning purpose as decision support tool.
Abstract: Cognitive radio devices have been considered as a key technology for next-generation of wireless communication. These devices in the context of IEEE 802.11 standards and IEEE 802.16 standards, can opportunistically utilize the wireless spectrum to achieve better user performance and improve the overall spectrumutilization efficiency, mainly in the unlicensed 5 GHz bands. However, opportunistic use of wireless spectrum creates news problems such as peaceful coexistence with other wireless technologies, such as the radiolocation systems, as well as understanding the influence of interference that each of these networks can create. In this paper, we suggest a dynamic access model that considerably reduces this interference and allows efficiency and fairness use of the wireless spectrum.
Abstract: This paper proposes an auto-classification algorithm
of Web pages using Data mining techniques. We consider the
problem of discovering association rules between terms in a set of
Web pages belonging to a category in a search engine database, and
present an auto-classification algorithm for solving this problem that
are fundamentally based on Apriori algorithm. The proposed
technique has two phases. The first phase is a training phase where
human experts determines the categories of different Web pages, and
the supervised Data mining algorithm will combine these categories
with appropriate weighted index terms according to the highest
supported rules among the most frequent words. The second phase is
the categorization phase where a web crawler will crawl through the
World Wide Web to build a database categorized according to the
result of the data mining approach. This database contains URLs and
their categories.
Abstract: The B'enard-Marangoni thermal instability problem for
a viscoelastic Jeffreys- fluid layer with internal heat generation is
investigated. The fluid layer is bounded above by a realistic free
deformable surface and by a plane surface below. Our analysis
shows that while the internal heat generation and the relaxation time
both destabilize the fluid layer, its stability may be enhanced by an
increased retardation time.
Abstract: In order to meet the limits imposed on automotive
emissions, engine control systems are required to constrain air/fuel
ratio (AFR) in a narrow band around the stoichiometric value, due to
the strong decay of catalyst efficiency in case of rich or lean mixture.
This paper presents a model of a sample spark ignition engine and
demonstrates Simulink-s capabilities to model an internal combustion
engine from the throttle to the crankshaft output. We used welldefined
physical principles supplemented, where appropriate, with
empirical relationships that describe the system-s dynamic behavior
without introducing unnecessary complexity. We also presents a PID
tuning method that uses an adaptive fuzzy system to model the
relationship between the controller gains and the target output
response, with the response specification set by desired percent
overshoot and settling time. The adaptive fuzzy based input-output
model is then used to tune on-line the PID gains for different
response specifications. Experimental results demonstrate that better
performance can be achieved with adaptive fuzzy tuning relative to
similar alternative control strategies. The actual response
specifications with adaptive fuzzy matched the desired response
specifications.
Abstract: Innovation is more important in any companies.
However, it is not easy to measure the innovation performance
correctly. Patent is one of measuring index nowadays. This paper
wants to purpose an approach for valuing patents based on market
reaction to patent infringement litigations. The interesting
phenomenon is found from collection of patent infringement litigation
events. That is if any patent litigation event occurs the stock value will
follow changing. The plaintiffs- stock value raises some percentage.
According to this interesting phenomenon, the relationship between
patent litigation and stock value is tested and verified. And then, the
stock value variation is used to deduce the infringed patents- value.
The purpose of this study is providing another concept model to
evaluate the infringed patents. This study can provide a decision assist
system to help drafting patent litigation strategy and determine the
technology value
Abstract: Apparel product development is an important stage in the life cycle of a product. Shortening this stage will help to reduce the costs of a garment. The aim of this study is to examine the production parameters in knitwear apparel companies by defining the unit costs, and developing a software to calculate the unit costs of garments and make the cost estimates. In this study, with the help of a questionnaire, different companies- systems of unit cost estimating and cost calculating were tried to be analyzed. Within the scope of the questionnaire, the importance of cost estimating process for apparel companies and the expectations from a new cost estimating program were investigated. According to the results of the questionnaire, it was seen that the majority of companies which participated to the questionnaire use manual cost calculating methods or simple Microsoft Excel spreadsheets to make cost estimates. Furthermore, it was discovered that many companies meet with difficulties in archiving the cost data for future use and as a solution to that problem, it is thought that prior to making a cost estimate, sub units of garment costs which are fabric, accessory and the labor costs should be analyzed and added to the database of the programme beforehand. Another specification of the cost estimating unit prepared in this study is that the programme was designed to consist of two main units, one of which makes the product specification and the other makes the cost calculation. The programme is prepared as a web-based application in order that the supplier, the manufacturer and the customer can have the opportunity to communicate through the same platform.
Abstract: A topologically oriented neural network is very
efficient for real-time path planning for a mobile robot in changing
environments. When using a recurrent neural network for this
purpose and with the combination of the partial differential equation
of heat transfer and the distributed potential concept of the network,
the problem of obstacle avoidance of trajectory planning for a
moving robot can be efficiently solved. The related dimensional
network represents the state variables and the topology of the robot's
working space. In this paper two approaches to problem solution are
proposed. The first approach relies on the potential distribution of
attraction distributed around the moving target, acting as a unique
local extreme in the net, with the gradient of the state variables
directing the current flow toward the source of the potential heat. The
second approach considers two attractive and repulsive potential
sources to decrease the time of potential distribution. Computer
simulations have been carried out to interrogate the performance of
the proposed approaches.