Abstract: The present study is concerned with effect of exciting
boundary layer on increase in heat transfer from flat surfaces. As any
increase in heat transfer between a fluid inside a face and another one
outside of it can cause an increase in some equipment's efficiency, so
at this present we have tried to increase the wall's heat transfer
coefficient by exciting the fluid boundary layer. By a collision
between flow and the placed block at the fluid way, the flow pattern
and the boundary layer stability will change. The flow way inside the
channel is simulated as a 2&3-dimensional channel by Gambit
TM
software.
With studying the achieved results by this simulation for the flow
way inside the channel with a block coordinating with Fluent
TM
software, it's determined that the figure and dimensions of the exciter
are too important for exciting the boundary layer so that any increase
in block dimensions in vertical side against the flow and any
reduction in its dimensions at the flow side can increase the average
heat transfer coefficient from flat surface and increase the flow
pressure loss. Using 2&3-dimensional analysis on exciting the flow at
the flow way inside a channel by cylindrical block at the same time
with the external flow, we came to this conclusion that the heat flux
transferred from the surface, is increased considerably in terms of the
condition without excitation. Also, the k-e turbulence model is used.
Abstract: Incompressible Navier-Stokes equations are reviewed
in this work. Three-dimensional Navier-Stokes equations are solved
analytically. The Mathematical derivation shows that the solutions
for the zero and constant pressure gradients are similar. Descriptions
of the proposed formulation and validation against two laminar
experiments and three different turbulent flow cases are reported in
this paper. Even though, the analytical solution is derived for nonreacting
flows, it could reproduce trends for cases including
combustion.
Abstract: In this study, a nickel film with nano-crystalline grains,
high hardness and smooth surface was electrodeposited using a post
supercritical carbon dioxide (CO2) mixed Watts electrolyte. Although
the hardness was not as high as its Sc-CO2 counterpart, the thin coating
contained significantly less number of nano-sized pinholes. By
measuring the escape concentration of the dissolved CO2 in post
Sc-CO2 mixed electrolyte with the elapsed time, it was believed that
the residue of dissolved CO2 bubbles should closely relate to the
improvement in hardness and surface roughness over its conventional
plating counterpart. Therefore, shortening the duration of
electroplating with the raise of current density up to 0.5 A/cm2 could
effectively retain more post Sc-CO2 mixing effect. This study not only
confirms the roles of dissolved CO2 bubbles in electrolyte but also
provides a potential process to overcome most issues associated with
the cost in building high-pressure chamber for large size products and
continuous plating using supercritical method.
Abstract: A steady two-phase flow model has been developed to simulate the drying process of porous particle in a pneumatic conveying dryer. The model takes into account the momentum, heat and mass transfer between the continuous phase and the dispersed phase. A single particle model was employed to calculate the evaporation rate. In this model the pore structure is simplified to allow the dominant evaporation mechanism to be readily identified at all points within the duct. The predominant mechanism at any time depends upon the pressure, temperature and the diameter of pore from which evaporating is occurring. The model was validated against experimental studies of pneumatic transport at low and high speeds as well as pneumatic drying. The effects of operating conditions on the dryer parameters are studied numerically. The present results show that the drying rate is enhanced as the inlet gas temperature and the gas flow rate increase and as the solid mass flow rate deceases. The present results also demonstrate the necessity of measuring the inlet gas velocity or the solid concentration in any experimental analysis.
Abstract: This research is to design and implement a new kind
of agitators called differential agitator. The Differential Agitator is an
electro- mechanic set consists of two shafts. The first shaft is the
bearing axis while the second shaft is the axis of the quartet upper
bearing impellers group and the triple lower group which are called
as agitating group. The agitating group is located inside a cylindrical
container equipped especially to contain square directors for the
liquid entrance and square directors called fixing group for the liquid
exit. The fixing group is installed containing the agitating group
inside any tank whether from upper or lower position. The agitating
process occurs through the agitating group bearing causing a lower
pressure over the upper group leading to withdrawing the liquid from
the square directors of the liquid entering and consequently the liquid
moves to the denser place under the quartet upper group. Then, the
liquid moves to the so high pressure area under the agitating group
causing the liquid to exit from the square directors in the bottom of
the container. For improving efficiency, parametric study and shape
optimization has been carried out. A numerical analysis,
manufacturing and laboratory experiments were conducted to design
and implement the differential agitator. Knowing the material
prosperities and the loading conditions, the FEM using ANSYS11
was used to get the optimum design of the geometrical parameters of
the differential agitator elements while the experimental test was
performed to validate the advantages of the differential agitators to
give a high agitation performance of lime in the water as an example.
In addition, the experimental work has been done to express the
internal container shape in the agitation efficiency. The study ended
up with conclusions to maximize agitator performance and optimize
the geometrical parameters to be used for manufacturing the
differential agitator
Abstract: Explosion occurs due to sudden release of energy.
Common examples of explosion include chemical, atomic, heat, and
pressure tank (due to ignition) explosions. Petroleum, gas, and
petrochemical industries operations are threatened by natural risks
and processes. Fires and explosions are the greatest process risks
which cause financial damages.
This study aims at designing a single-floor structure for the control
room of a petroleum refinery to be resistant against gas explosion
loads, and the information related to the structure specifications have
been provided regarding the fact that the structure is made on the
ground's surface. In this research, the lateral stiffness of single pile is
calculated by SPPLN.FOR computer program, and its value for
13624 KN/m single pile has been assessed. The analysis used due to
the loading conditions, is dynamic nonlinear analysis with direct
integration method.
Abstract: Total liquid ventilation can support gas exchange in animal models of lung injury. Clinical application awaits further technical improvements and performance verification. Our aim was to develop a liquid ventilator, able to deliver accurate tidal volumes, and a computerized system for measuring lung mechanics. The computer-assisted, piston-driven respirator controlled ventilatory parameters that were displayed and modified on a real-time basis. Pressure and temperature transducers along with a lineal displacement controller provided the necessary signals to calculate lung mechanics. Ten newborn lambs (
Abstract: In the current study, we have conducted an experimental investigation on the utilization of electronic arc furnace (EAF) reducing slag for the absorption of CO2 via wet grinding method. It was carried out by various grinding conditions. The slag was ground in the vibrating ball mill in the presence of CO2 and pure water under ambient temperature. The reaction behavior was monitored with constant pressure method, and the changes of experimental systems volume as a function of grinding time were measured. It was found that the CO2 absorption occurred as soon as the grinding started. The CO2 absorption was significantly increased in the case of wet grinding compare to the dry grinding. Generally, the amount of CO2 absorption increased as the amount of water, weight of slag and initial pressure increased. However, it was decreased when the amount of water exceeds 200ml and when smaller balls were used. The absorption of CO2 occurred simultaneously with the start of the grinding and it stopped when the grinding was stopped. According to this research, the CO2 reacted with the CaO inside the slag, forming CaCO3.
Abstract: Subcritical water extraction was investigated as a
novel and alternative technology in the food and pharmaceutical
industry for the separation of Mannitol from olive leaves and its
results was compared with those of Soxhlet extraction. The effects of
temperature, pressure, and flow rate of water and also momentum
and mass transfer dimensionless variables such as Reynolds and
Peclet Numbers on extraction yield and equilibrium partition
coefficient were investigated. The 30-110 bars, 60-150°C, and flow
rates of 0.2-2 mL/min were the water operating conditions. The
results revealed that the highest Mannitol yield was obtained at
100°C and 50 bars. However, extraction of Mannitol was not
influenced by the variations of flow rate. The mathematical modeling
of experimental measurements was also investigated and the model is
capable of predicting the experimental measurements very well. In
addition, the results indicated higher extraction yield for the
subcritical water extraction in contrast to Soxhlet method.
Abstract: This paper provides an exergy analysis of the multistage refrigeration cycle used for C2+ recovery plant. The behavior of an industrial refrigeration cycle with refrigerant propane has been investigated by the exergy method. A computational model based on the exergy analysis is presented for the investigation of the effects of the valves on the exergy losses, the second law of efficiency, and the coefficient of performance (COP) of a vapor compression refrigeration cycle. The equations of exergy destruction and exergetic efficiency for the main cycle components such as evaporators, condensers, compressors, and expansion valves are developed. The relations for the total exergy destruction in the cycle and the cycle exergetic efficiency are obtained. An ethane recovery unit with its refrigeration cycle has been simulated to prepare the exergy analysis. Using a typical actual work input value; the exergetic efficiency of the refrigeration cycle is determined to be 39.90% indicating a great potential for improvements. The simulation results reveal that the exergetic efficiencies of the heat exchanger and expansion sections get the lowest rank among the other compartments of refrigeration cycle. Refrigeration calculations have been carried out through the analysis of T–S and P–H diagrams where coefficient of performance (COP) was obtained as 1.85. The novelty of this article includes the effect and sensitivity analysis of molar flow, pressure drops and temperature on the exergy efficiency and coefficient of performance of the cycle.
Abstract: Dual bell nozzle is a promising one among the altitude
adaptation nozzle concepts, which offer increased nozzle
performance in rocket engines. Its advantage is the simplicity it offers
due to the absence of any additional mechanical device or movable
parts. Hence it offers reliability along with improved nozzle
performance as demanded by future launch vehicles. Among other
issues, the flow transition to the extension nozzle of a dual bell
nozzle is one of the major issues being studied in the development of
dual bell nozzle. A parameter named over-expansion factor, which
controls the value of the wall inflection angle, has been reported to
have substantial influence in this transition process. This paper
studies, through CFD and cold flow experiments, the effect of overexpansion
factor on flow transition in dual bell nozzles.
Abstract: High pressure adsorption of carbon dioxide on zeolite
13X was investigated in the pressure range (0 to 4) Mpa and
temperatures 298, 308 and 323K. The data fitting is accomplished
with the Toth, UNILAN, Dubinin-Astakhov and virial adsorption
models which are generally used for micro porous adsorbents such as
zeolites. Comparison with experimental data from the literature
indicated that the virial model would best determine results. These
results may be partly attributed to the flexibility of the virial model
which can accommodate as many constants as the data warrants.
Abstract: An experimental investigation was performed on pulp
liquid flow in straight ducts with a square cross section. Fully
developed steady flow was visualized and the fiber concentration was
obtained using a light-section method developed by the author et al.
The obtained results reveal quantitatively, in a definite form, the
distribution of the fiber concentration. From the results and
measurements of pressure loss, it is found that the flow characteristics
of pulp liquid in ducts can be classified into five patterns. The
relationships among the distributions of mean and fluctuation of fiber
concentration, the pressure loss and the flow velocity are discussed,
and then the features for each pattern are extracted. The degree of
nonuniformity of the fiber concentration, which is indicated by the
standard deviation of its distribution, is decreased from 0.3 to 0.05
with an increase in the velocity of the tested pulp liquid from 0.4 to
0.8%.
Abstract: Recently, the health of retired National Football
League players, particularly lineman has been investigated. A number of studies have reported increased cardiometabolic risk, premature ardiovascular disease and incidence of type 2 diabetes. Rugby union players have somatotypes very similar
to National Football league players which suggest that rugby players may have similar health risks. The International Golden Oldies World Rugby Festival (GORF) provided a
unique opportunity to investigate the demographics of veteran rugby players. METHODOLOGIES: A cross-sectional, observational study was completed using an online web-based
questionnaire that consisted of medical history and
physiological measures. Data analysis was completed using a one sample t-test (50yrs) and Chi-square test. RESULTS: A total of 216 veteran rugby competitors
(response rate = 6.8%) representing 10 countries, aged 35-72 yrs (mean 51.2, S.D. ±8.0), participated in the online survey. As a group, the incidence of current smokers was low at 8.8%
(avg 72.4 cigs/wk) whilst the percentage consuming alcohol
was high (93.1% (avg 11.2 drinks/wk). Competitors reported
the following top six chronic diseases/disorders; hypertension
(18.6%), arthritis (OA/RA, 11.5%), asthma (9.3%),
hyperlipidemia (8.2%), diabetes (all types, 7.5%) and gout (6%), there were significant differences between groups with
regard to cancer (all types) and migraines. When compared to
the Australian general population (Australian Bureau of Statistics data, n=18,000), GORF competitors had a
Climstein Mike, Walsh Joe (corresponding author) and Burke Stephen
School of Exercise Science, Australian Catholic University, 25A Barker Road,
Strathfield, Sydney, NSW, 2016, Australia (e-mail:
[email protected], [email protected],
[email protected]).
John Best is with Orthosports, 160 Belmore Rd., Randwick, Sydney,NSW
2031, Australia (e-mail: [email protected]).
Heazlewood, Ian Timothy is with School of Environmental and Life
Sciences, Faculty Education, Health and Science, Charles Darwin University,
Precinct Yellow Building 2, Charles Darwin University, NT 0909, Australia
(e-mail: [email protected]).
Kettunen Jyrki Arcada University of Applied Sciences, Jan-Magnus
Janssonin aukio 1, FI-00550, Helsinki, Finland (e-mail:
[email protected]).
Adams Kent is with California State University Monterey Bay, Kinesiology Department, 100 Campus Center, Seaside, CA., 93955, USA (email: [email protected]).
DeBeliso Mark is with Department of Physical Education and Human
Performance, Southern Utah University, 351 West University Blvd, Cedar
City, Utah, USA (e-mail: [email protected]).
significantly lower incidence of anxiety (p
Abstract: This paper describes the design and development of pico-hydro generation system using consuming water distributed to houses. Water flow in the domestic pipes has kinetic energy that potential to generate electricity for energy storage purposes in addition to the routine activities such as laundry, cook and bathe. The inherent water pressure and flow inside the pipe from utility-s main tank that used for those usual activities is also used to rotate small scale hydro turbine to drive a generator for electrical power generation. Hence, this project is conducted to develop a small scale hydro generation system using consuming water distributed to houses as an alternative electrical energy source for residential use.
Abstract: This paper investigates the effect of replacing
crankshaft with cam on the indicated torque during compression and
power strokes in internal combustion engines. A Cycloidal cam
profile was used in Revetec engine to calculate and compare the
torque to a conventional engine, using a computational method.
Firstly, the cylinder pressure was calculated using Ferguson equation,
and then the torque calculated depending on cylinder pressure values
in every crank angle. the results showed that by using Cycloidal cam
profile in Revetec engine the torque can increased by 14% compared
with conventional engines, which means an increase in engine
efficiency.
Abstract: In the present paper; an experimental and numerical
investigations of drag reduction on a grooved circular cylinder have
been performed. The experiments were carried out in closed circuit
subsonic wind tunnel (TE44); the pressure distribution on the
cylinder was conducted using a TE44DPS differential pressure
scanner and the drag forces were measured using the TE81 balance.
The display unit is linked to a computer, loaded with DATASLIM
software for data analysis and logging of result. The numerical study
was performed using the code ANSYS FLUENT solving the
Reynolds Averaged Navier-Stokes (RANS) equations. The k-ε and k-
ω SST models were tested. The results obtained from the
experimental and numerical investigations have showed a reduction
in the drag when using longitudinal grooves namely 2 and 6 on the
cylinder.
Abstract: The Yazd-Ardakan basin in Central Iran has two separated aquifers. The shallow unconfined aquifer is supplies 40 Qanats. The deep saturated confined aquifer is the main water storage. Due to over-withdrawal, water table has been decreasing during last 25 years. Recent study shows that the shortage of the aquifer is about 16 meters and land subsidence is 0.5 - 1.2 meters. Long deep cracks are found just above the aquifer and devour the irrigation water and floods. Although the most cracks direction is NW-SE and could be compared to the main direction of YA basin, there is no direct evidence for relation between land subsidence and the huge cracks. Large-scale water pumping has been decreased the water pressure in aquifer. The pressure decline disturbed the balance and increased the pressure of overlying sediments. So porosity decreased and compaction started. Then, sediments compaction developed and made land subsidence and some huge cracks slowly.
Abstract: Gas hydrates form when a number of factors co-exist:
free water, hydrocarbon gas, cold temperatures and high pressures are typical of the near mud-line conditions in a deepwater drilling
operation. Subsequently, when drilling with water based muds, particularly on exploration wells, the risk of hydrate formation
associated with a gas influx is high. The consequences of gas hydrate
formation while drilling are severe, and as such, every effort should be made to ensure the risk of hydrate formation is either eliminated
or significantly reduced. Thermodynamic inhibitors are used to reduce the free water content of a drilling mud, and thus suppress the
hydrate formation temperature. Very little experimental work has
been performed by oil and gas research companies on the evaluation
of gas hydrate formation in a water-based drilling mud. The main
objective of this paper is to investigate the experimental gas hydrate
formation for a mixture of methane, carbon dioxide & nitrogen in a
water-based drilling mud with or without presence of different
concentrations of thermodynamic inhibitors including pure salt and a
combination of salt with methanol or ethylene glycol at different
concentrations in a static loop apparatus. The experiments were
performed using a static loop apparatus consisting of a 2.4307 cm
inside diameter and 800 cm long pipe. All experiments were conducted at 2200 psia. The temperature in the loop was decreased at
a rate of 3.33 °F/h from initial temperature of 80 °F.
Abstract: We introduce an effective approach for automatic offline au- thentication of handwritten samples where the forgeries are skillfully done, i.e., the true and forgery sample appearances are almost alike. Subtle details of temporal information used in online verification are not available offline and are also hard to recover robustly. Thus the spatial dynamic information like the pen-tip pressure characteristics are considered, emphasizing on the extraction of low density pixels. The points result from the ballistic rhythm of a genuine signature which a forgery, however skillful that may be, always lacks. Ten effective features, including these low density points and den- sity ratio, are proposed to make the distinction between a true and a forgery sample. An adaptive decision criteria is also derived for better verification judgements.