Abstract: Thyroid dysfunction is one of the most frequently
reported complications of chronic blood transfusion therapy in patients with beta-thalassemia major (BTM). However, the occurrence of thyroid dysfunction and its possible association with
iron overload in BTM patients is still under debate. Therefore, this
study aimed to investigate the status of thyroid functions and iron overload in adolescent and young adult patients with BTM in Jordan population. Thirty six BTM patients aged 12-28 years and matched controls were included in this study. All patients have been receiving frequent blood transfusion to maintain pretransfusion hemoglobin
concentration above 10 g dl-1 and deferoxamine at a dose of 45 mg kg-1 day-1 (8 h, 5-7 days/week) by subcutaneous infusion. Blood
samples were drawn from patients and controls. The status of thyroid functions and iron overload was evaluated by measurements of serum
free thyroxine (FT4), triiodothyronine (FT3), thyrotropin (TSH) and
serum ferritin level. A number of some hematological and
biochemical parameters were also measured. It was found that hematocrit, serum ferritin, hemoglobin, FT3 and zinc, copper mean values were significantly higher in the patients than in the controls (P< 0.05). On other hand, leukocyte, FT4 and TSH mean values were
similar to that of the controls. In addition, our data also indicated that
all of the above examined parameters were not significantly affected
by the patient-s age and gender. Deferoxamine approach for removing excess iron from our BTM patient did not normalize the
values of serum ferritin, copper and zinc, suggesting poor compliance
with deferoxamine chelation therapy. Thus, we recommend the use
of a combination of deferoxamine and deferiprone to reduce the risk
of excess of iron in our patients. Furthermore, thyroid dysfunction
appears to be a rare complication, because our patients showed
normal mean levels for serum TSH and FT4. However, high mean
levels of serum ferritin, zinc, copper might be seen as potential risk
factors for initiation and development of thyroid dysfunctions and
other diseases. Therefore, further studies must be carried out at
yearly intervals with large sample number, to detect subclinical
thyroid dysfunction cases.
Abstract: This paper proves that the problem of finding connected
vertex cover in a 2-connected planar graph ( CVC-2 ) with maximum degree 4 is NP-complete. The motivation for proving this result is to
give a shorter and simpler proof of NP-Completeness of TRA-MLC (the Top Right Access point Minimum-Length Corridor) problem [1], by finding the reduction from CVC-2. TRA-MLC has many applications in laying optical fibre cables for data communication and electrical wiring in floor plans.The problem of finding connected vertex cover in any planar graph ( CVC ) with maximum degree 4 is NP-complete [2]. We first show that CVC-2 belongs to NP and then we find a polynomial reduction from CVC to CVC-2. Let a graph G0 and an integer K form an instance of CVC, where G0 is a planar graph and K is an upper bound on the size of the connected vertex cover in G0. We construct a 2-connected planar graph, say G, by identifying the blocks and cut vertices of G0, and then finding the planar representation of all the blocks of G0, leading to a plane graph G1. We replace the cut vertices with cycles in such a way that the resultant graph G is a 2-connected planar graph with maximum
degree 4. We consider L = K -2t+3 t i=1 di where t is the number of cut vertices in G1 and di is the number of blocks for which ith cut vertex is common. We prove that G will have a connected vertex
cover with size less than or equal to L if and only if G0 has a connected vertex cover of size less than or equal to K.
Abstract: Semnan is a city in semnan province, northern Iran
with a population estimated at 119,778 inhabitants. It is the
provincial capital of semnan province. Iran is a developing country
and construction is a basic factor of developing too. Hence, Semnan
city needs to a special programming for construction of buildings,
structures and infrastructures. Semnan municipality tries to begin this
program. In addition to, city has some historical monuments which
can be interesting for tourists. Hence, Semnan inhabitants can benefit
from tourist industry. Optimization of Energy in construction
industry is another activity of this municipality and the inhabitants
who execute these regulations receive some discounts. Many parts of
Iran such as semnan are located in highly seismic zones and
structures must be constructed safe e.g., according to recent seismic
codes. In this paper opportunities of IT in construction industry of
Iran are investigated in three categories. Pre-construction phase,
construction phase and earthquake disaster mitigation are studied.
Studies show that information technology can be used in these items
for reducing the losses and increasing the benefits. Both government
and private sectors must contribute to this strategic project for
obtaining the best result.
Abstract: We examined whether children ( < 18 years old) had risk of intra-thoracic trauma during 'one-handed' chest compressions through MDCT images. We measured the length of the lower half of the sternum (Stotal/2~X). We also measured the distance from the diaphragm to the midpoint of the sternum (Stotal/2~D) and half the width of an adult hand (Wtotal/2). All the 1 year-old children had Stotal/2~X and Stotal/2~D less than Wtotal/2. Among the children aged 2 years, 6 (60.0%) had Stotal/2~X and Stotal/2~D less than Wtotal/2. Among those aged 3 years, 4 (26.7%) had Stotal/2~X and Stotal/2~D less than Wtotal/2, and among those aged 4 years, 2 (13.3%) had Stotal/2~X and Stotal/2~D less than Wtotal/2. However, Stotal/2~X and Stotal/2~D were greater than Wtotal/2 in children aged 5 years or more. We knew that small children may be at an increased risk of intra-thoracic trauma during 'one-handed' chest compressions.
Abstract: This paper summarizes the results of some experiments for finding the effective features for disambiguation of Turkish verbs. Word sense disambiguation is a current area of investigation in which verbs have the dominant role. Generally verbs have more senses than the other types of words in the average and detecting these features for verbs may lead to some improvements for other word types. In this paper we have considered only the syntactical features that can be obtained from the corpus and tested by using some famous machine learning algorithms.
Abstract: This paper proposes a new technique to detect code
clones from the lexical and syntactic point of view, which is based
on PALEX source code representation. The PALEX code contains
the recorded parsing actions and also lexical formatting information
including white spaces and comments. We can record a list of parsing
actions (shift, reduce, and reading a token) during a compiling process
after a compiler finishes analyzing the source code. The proposed
technique has advantages for syntax sensitive approach and language
independency.
Abstract: Nowadays there is a growing environmental concern
and the business communities have slowly started recognising
environmental protection and sustainable utilization of natural
resources into their marketing strategies. This paper discusses the
various Ecolabeling and Certification Systems developed world
over to regulate and introduce Fair Trade in Ornamental Fish
Industry. Ecolabeling and green certification are considered as part
of these strategies implemented partly out of compulsion from the
National and International Regulatory Bodies and Environmental
Movements. All the major markets of ornamental fishes like
European Union, USA and Japan have started putting restrictions on
the trade to impose ecolabeling as a non tariff barrier like the one
imposed on seafood and aqua cultured products. A review was done
on the available Ecolabeling and Green Certification Schemes
available at local, national and international levels for fisheries
including aquaculture and ornamental fish trade and to examine the
success and constraints faced by these schemes during its
implementation. The primary downside of certification is the
multiplicity of ecolabels and cost incurred by applicants for
certification, costs which may in turn be passed on to consumers.
The studies reveal serious inadequacies in a number of ecolabels
and cast doubt on their overall contribution to effective fisheries
management and sustainability. The paper also discusses the
inititive taken in India to develop guidelines for Green Certification
of Fresh water ornamental fishes.
Abstract: Discrete Wavelet Transform (DWT) has demonstrated
far superior to previous Discrete Cosine Transform (DCT) and
standard JPEG in natural as well as medical image compression. Due
to its localization properties both in special and transform domain,
the quantization error introduced in DWT does not propagate
globally as in DCT. Moreover, DWT is a global approach that avoids
block artifacts as in the JPEG. However, recent reports on natural
image compression have shown the superior performance of
contourlet transform, a new extension to the wavelet transform in two
dimensions using nonseparable and directional filter banks,
compared to DWT. It is mostly due to the optimality of contourlet in
representing the edges when they are smooth curves. In this work, we
investigate this fact for medical images, especially for CT images,
which has not been reported yet. To do that, we propose a
compression scheme in transform domain and compare the
performance of both DWT and contourlet transform in PSNR for
different compression ratios (CR) using this scheme. The results
obtained using different type of computed tomography images show
that the DWT has still good performance at lower CR but contourlet
transform performs better at higher CR.
Abstract: Laser interferometric methods have been utilized for the measurement of natural convection heat transfer from a heated vertical flat plate, in the investigation presented here. The study mainly aims at comparing two different fringe orientations in the wedge fringe setting of Mach-Zehnder interferometer (MZI), used for the measurements. The interference fringes are set in horizontal and vertical orientations with respect to the heated surface, and two different fringe analysis methods, namely the stepping method and the method proposed by Naylor and Duarte, are used to obtain the heat transfer coefficients. The experimental system is benchmarked with theoretical results, thus validating its reliability in heat transfer measurements. The interference fringe patterns are analyzed digitally using MATLAB 7 and MOTIC Plus softwares, which ensure improved efficiency in fringe analysis, hence reducing the errors associated with conventional fringe tracing. The work also discuss the relative merits and limitations of the two methods used.
Abstract: This paper study the high-level modelling and design
of delta-sigma (ΔΣ) noise shapers for audio Digital-to-Analog
Converter (DAC) so as to eliminate the in-band Signal-to-Noise-
Ratio (SNR) degradation that accompany one channel mismatch in
audio signal. The converter combines a cascaded digital signal
interpolation, a noise-shaping single loop delta-sigma modulator with
a 5-bit quantizer resolution in the final stage. To reduce sensitivity of
Digital-to-Analog Converter (DAC) nonlinearities of the last stage, a
high pass second order Data Weighted Averaging (R2DWA) is
introduced. This paper presents a MATLAB description modelling
approach of the proposed DAC architecture with low distortion and
swing suppression integrator designs. The ΔΣ Modulator design can
be configured as a 3rd-order and allows 24-bit PCM at sampling rate
of 64 kHz for Digital Video Disc (DVD) audio application. The
modeling approach provides 139.38 dB of dynamic range for a 32
kHz signal band at -1.6 dBFS input signal level.
Abstract: This paper proposes a new optimal feedback controller
for voltage source converters VSC's, for current regulated voltage
source converters, which allows compensate the harmonics of current
produced by nonlinear loads and load reactive power. The aim of the
present paper is to describe a novel switching signal generation
technique called optimal controller which guarantees that the injected
currents follow the reference currents determined by the
compensation strategy, with the smallest possible tracking error and
fixed switching frequency. It is compared with well-known
hysteresis current controller HCC. The validity of presented method
and its comparison with HCC is studied through simulation results.
Abstract: A cross-sectional study was carried out to determine the prevalence, species characterization and associated risk factors with Eimeria (E.) in sheep of district Toba Tek Singh from April, 2009 to March, 2010. Of the total 486 faecal samples examined for Eimeria, 209 (43%) were found infected with five species of Eimeria. Amongst the identified species of Eimeria, E. ovinoidalis was the commonest one (48.32%), followed in order by E. ahsata, E. intricata, E. parva and E. faurei with prevalence of 45.45, 28.71, 24.40 and 19.14 percent respectively. Peak prevalence was observed in August. Wet season (rainy and post-rainy) was found to be favourable for Eimeria infection. Lambs had significantly higher prevalence (P < 0.05) of Eimeria than adults. Similarly higher prevalence of Eimeria was observed in female as compared to male. Among management and husbandry practices; watering system, housing system, floor type and herd size strongly influenced the prevalence of Eimeria. Coccidiosis was more prevalent in closed housing system, non-cemented floor type, pond watered animals and larger herds (P < 0.05) as compared to open housing system, partially cemented floor type, tap watered animals and smaller herds respectively. Feeding system, breed and body condition of animals were not found as risk factors (P>0.05) influencing prevalence of Eimeria.
Abstract: Extreme temperature of several stations in Malaysia is
modelled by fitting the monthly maximum to the Generalized
Extreme Value (GEV) distribution. The Mann-Kendall (MK) test
suggests a non-stationary model. Two models are considered for
stations with trend and the Likelihood Ratio test is used to determine
the best-fitting model. Results show that half of the stations favour a
model which is linear for the location parameters. The return level is
the level of events (maximum temperature) which is expected to be
exceeded once, on average, in a given number of years, is obtained.
Abstract: A biosensor based on glucose oxidase (GOx) immobilized onto nanoparticles zirconium oxide with polyethylene nanocomposite for glucose monitoring has been designed. The CTAB/PEG/ZrO2/GOx nanocomposite was deposited onto screen printed carbon paste (SPCE) electrode via spin coating technique. The properties of CTAB/PEG/ZrO2/GOx were study using scanning electron microscopy (SEM). The SPE modified with the CTAB/PEG/ZrO2/GOx showed electrocatalytical response to the oxidation of glucose when ferrocene carboxaldehyde was used as an artificial redox mediator, which was studied by cyclic voltammetry (CV). Several parameters such as working potential, effect of pH and effect of ZrO2/PEG layers that governed the analytical performance of the biosensor, have been studied. The biosensor was applied to detect glucose with a linear range of 0.4 to 2.0 mmol L−1 with good repetability and reproducibility.
Abstract: The paper is concerned with the technological process of renovation of shafts used in industrial manufacturing for extruding of sheet material. In the classical renovation technologies, a chrome based coating is applied to the working surface of the shaft in galvanic baths. The process, however, is known to be exclusively harmful due to the waste cyanide products. In this work, we present an advanced nanotechnology based on nonelectric chemical laying of a nickel coating with included nanoparticles. The technology is environmentally harmless and the new coating features an increased hardness and wear resistance. Results from experimental tests of the nanostructured nickel coating are presented and discussed.
Abstract: Antimicrobial (AM) starch-based films were
developed by incorporating chitosan and lauric acid as antimicrobial
agent into starch-based film. Chitosan has wide range of applications
as a biomaterial, but barriers still exist to its broader use due to its
physical and chemical limitations. In this work, a series of
starch/chitosan (SC) blend films containing 8% of lauric acid was
prepared by casting method. The structure of the film was
characterized by Fourier transform infrared spectroscopy (FTIR), Xray
diffraction (XRD), and scanning electron microscopy (SEM).
The results indicated that there were strong interactions were present
between the hydroxyl groups of starch and the amino groups of
chitosan resulting in a good miscibility between starch and chitosan
in the blend films. Physical properties and optical properties of the
AM starch-based film were evaluated. The AM starch-based films
incorporated with chitosan and lauric acid showed an improvement in
water vapour transmission rate (WVTR) and addition of starch
content provided more transparent films while the yellowness of the
film attributed to the higher chitosan content. The improvement in
water barrier properties was mainly attributed to the hydrophobicity
of lauric acid and optimum chitosan or starch content. AM starch
based film also showed excellent oxygen barrier. Obtaining films
with good oxygen permeability would be an indication of the
potential use of these antimicrobial packaging as a natural packaging
and an alternative packaging to the synthetic polymer to protect food
from oxidation reactions
Abstract: For many industrial applications plate heat
exchangers are demonstrating a large superiority over the
other types of heat exchangers. The efficiency of such a
device depends on numerous factors the effect of which needs
to be analysed and accurately evaluated.
In this paper we present a theoretical analysis of a cocurrent
plate heat exchanger and the results of its numerical
simulation.
Knowing the hot and the cold fluid streams inlet temperatures,
the respective heat capacities mCp
and the value of the
overall heat transfer coefficient, a 1-D mathematical model
based on the steady flow energy balance for a differential
length of the device is developed resulting in a set of N first
order differential equations with boundary conditions where N
is the number of channels.For specific heat exchanger
geometry and operational parameters, the problem is
numerically solved using the shooting method.
The simulation allows the prediction of the temperature
map in the heat exchanger and hence, the evaluation of its
performances. A parametric analysis is performed to evaluate
the influence of the R-parameter on the e-NTU values. For
practical purposes effectiveness-NTU graphs are elaborated
for specific heat exchanger geometry and different operating
conditions.
Abstract: This manuscript presents a fast blind signature scheme
with extremely low computation for users. Only several modular additions
and multiplications are required for a user to obtain and verify
a signature in the proposed scheme. Comparing with the existing
ones in the literature, the scheme greatly reduces the computations
for users.
Abstract: In this paper, several different types of natural gas liquefaction cycle. First, two processes are a cascade process with two staged compression were designed and simulated. These include Inter-cooler which is consisted to Propane, Ethylene and Methane cycle, and also, liquid-gas heat exchanger is applied to between of methane and ethylene cycles (process2) and between of ethylene and propane (process2). Also, these cycles are compared with two staged cascade process using only a Inter-cooler (process1). The COP of process2 and process3 showed about 13.99% and 6.95% higher than process1, respectively. Also, the yield efficiency of LNG improved comparing with process1 by 13.99% lower specific power. Additionally, C3MR process are simulated and compared with Process 2.
Abstract: The objective of this paper is to analyse the
application of the Half-Sweep Gauss-Seidel (HSGS) method by using
the Half-sweep approximation equation based on central difference
(CD) and repeated trapezoidal (RT) formulas to solve linear fredholm
integro-differential equations of first order. The formulation and
implementation of the Full-Sweep Gauss-Seidel (FSGS) and Half-
Sweep Gauss-Seidel (HSGS) methods are also presented. The HSGS
method has been shown to rapid compared to the FSGS methods.
Some numerical tests were illustrated to show that the HSGS method
is superior to the FSGS method.