Abstract: Regenerative Thermal Oxidizer (RTO) is one of the
best solutions for removal of Volatile Organic Compounds (VOC)
from industrial processes. In the RTO, VOC in a raw gas are usually
decomposed at 950-1300 K and the combustion heat of VOC is
recovered by regenerative heat exchangers charged with ceramic
honeycombs. The optimization of the treatment of VOC leads to the
reduction of fuel addition to VOC decomposition, the minimization of
CO2 emission and operating cost as well.
In the present work, the thermal efficiency of the RTO was
investigated experimentally in a pilot-scale RTO unit using toluene as
a typical representative of VOC. As a result, it was recognized that the
radiative heat transfer was dominant in the preheating process of a raw
gas when the gas flow rate was relatively low. Further, it was found
that a minimum heat exchanger volume to achieve self combustion of
toluene without additional heating of the RTO by fuel combustion was
dependent on both the flow rate of a raw gas and the concentration of
toluene. The thermal efficiency calculated from fuel consumption and
the decomposed toluene ratio, was found to have a maximum value of
0.95 at a raw gas mass flow rate of 1810 kg·h-1 and honeycombs height
of 1.5m.
Abstract: This paper is a continuation of our interest in the influence of temperature on specific retention volumes and the resulting infinite dilution activity coefficients. This has a direct effect in the design of absorption and stripping columns for the abatement of volatile organic compounds. The interaction of 13 volatile organic compounds (VOCs) with polydimethylsiloxane (PDMS) at varying temperatures was studied by gas liquid chromatography (GLC). Infinite dilution activity coefficients and specific retention volumes obtained in this study were found to be in agreement with those obtained from static headspace and group contribution methods by the authors as well as literature values for similar systems. Temperature variation also allows for transport calculations for different seasons. The results of this work confirm that PDMS is well suited for the scrubbing of VOCs from waste gas streams. Plots of specific retention volumes against temperature gave linear van-t Hoff plots.
Abstract: Vehicle which are turning or maneuvering at high speeds
are susceptible to sliding and subsequently deviate from desired path. In
this paper the dynamics governing the Yaw/Roll behavior of a vehicle
has been simulated. Two different simulations have been used one for
the real vehicle, for which a fuzzy controller is designed to increase its
directional stability property. The other simulation is for a hypothetical
vehicle with much higher tire cornering stiffness which is capable of
developing the required lateral forces at the tire-ground patch contact to
attain the desired lateral acceleration for the vehicle to follow the
desired path without slippage. This simulation model is our reference
model.
The logic for keeping the vehicle on the desired track in the cornering
or maneuvering state is to have some braking forces on the inner or
outer tires based on the direction of vehicle deviation from the desired
path. The inputs to our vehicle simulation model is steer angle δ and
vehicle velocity V , and the outputs can be any kinematical parameters
like yaw rate, yaw acceleration, side slip angle, rate of side slip angle
and so on. The proposed fuzzy controller is a feed forward controller.
This controller has two inputs which are steer angle δ and vehicle
velocity V, and the output of the controller is the correcting moment M,
which guides the vehicle back to the desired track. To develop the
membership functions for the controller inputs and output and the fuzzy
rules, the vehicle simulation has been run for 1000 times and the
correcting moment have been determined by trial and error. Results of
the vehicle simulation with fuzzy controller are very promising
and show the vehicle performance is enhanced greatly over the
vehicle without the controller. In fact the vehicle performance
with the controller is very near the performance of the reference
ideal model.
Abstract: In areas of low to moderate seismicity many building contents and equipment are not positively fixed to the floor or tied to adjacent walls. Under seismic induced horizontal vibration, such contents and equipment can suffer from damage by either overturning or impact associated with rocking. This paper focuses on the estimation of shock on typical contents and equipment due to rocking. A simplified analytical model is outlined that can be used to estimate the maximum acceleration on a rocking object given its basic geometric and mechanical properties. The developed model was validated against experimental results. The experimental results revealed that the maximum shock acceleration can be underestimated if the static stiffness of the materials at the interface between the rocking object and floor is used rather than the dynamic stiffness. Excellent agreement between the model and experimental results was found when the dynamic stiffness for the interface material was used, which was found to be generally much higher than corresponding static stiffness under different investigated boundary conditions of the cushion. The proposed model can be a beneficial tool in performing a rapid assessment of shock sensitive components considered for possible seismic rectification.
Abstract: This paper provides the design steps of a robust Linear
Matrix Inequality (LMI) based iterative multivariable PID controller
whose duty is to drive a sample power system that comprises a
synchronous generator connected to a large network via a step-up
transformer and a transmission line. The generator is equipped with
two control-loops, namely, the speed/power (governor) and voltage
(exciter). Both loops are lumped in one where the error in the
terminal voltage and output active power represent the controller
inputs and the generator-exciter voltage and governor-valve position
represent its outputs. Multivariable PID is considered here because of
its wide use in the industry, simple structure and easy
implementation. It is also preferred in plants of higher order that
cannot be reduced to lower ones. To improve its robustness to
variation in the controlled variables, H∞-norm of the system transfer
function is used. To show the effectiveness of the controller, divers
tests, namely, step/tracking in the controlled variables, and variation
in plant parameters, are applied. A comparative study between the
proposed controller and a robust H∞ LMI-based output feedback is
given by its robustness to disturbance rejection. From the simulation
results, the iterative multivariable PID shows superiority.
Abstract: In this paper, a novel method for recognition of musical
instruments in a polyphonic music is presented by using an
embedded hidden Markov model (EHMM). EHMM is a doubly
embedded HMM structure where each state of the external HMM
is an independent HMM. The classification is accomplished for
two different internal HMM structures where GMMs are used as
likelihood estimators for the internal HMMs. The results are compared
to those achieved by an artificial neural network with two
hidden layers. Appropriate classification accuracies were achieved
both for solo instrument performance and instrument combinations
which demonstrates that the new approach outperforms the similar
classification methods by means of the dynamic of the signal.
Abstract: Losses reduction initiatives in distribution systems
have been activated due to the increasing cost of supplying
electricity, the shortage in fuel with ever-increasing cost to produce
more power, and the global warming concerns. These initiatives have
been introduced to the utilities in shape of incentives and penalties.
Recently, the electricity distribution companies in Oman have been
incentivized to reduce the distribution technical and non-technical
losses with an equal annual reduction rate for 6 years. In this paper,
different techniques for losses reduction in Mazoon Electricity
Company (MZEC) are addressed. In this company, high numbers of
substation and feeders were found to be non-compliant with the
Distribution System Security Standard (DSSS). Therefore, 33
projects have been suggested to bring non-complying 29 substations
and 28 feeders to meet the planed criteria and to comply with the
DSSS. The largest part of MZEC-s network (South Batinah region)
was modeled by ETAP software package. The model has been
extended to implement the proposed projects and to examine their
effects on losses reduction. Simulation results have shown that the
implementation of these projects leads to a significant improvement
in voltage profile, and reduction in the active and the reactive power
losses. Finally, the economical analysis has revealed that the
implementation of the proposed projects in MZEC leads to an annual
saving of about US$ 5 million.
Abstract: In this paper, we propose synchronization of an array of nonlinear systems with time delays. The array of systems is decomposed into isolated systems to establish appropriate Lyapunov¬Krasovskii functional. Using the Lyapunov-Krasovskii functional, a sufficient condition for the synchronization is derived in terms of LMIs(Linear Matrix Inequalities). Delayed feedback control gains are obtained by solving the sufficient condition. Numerical examples are given to show the validity the proposed method.
Abstract: This paper presents the feasibility study of CO2 sequestration from the sources to the sinks in the prospective of Italian Industries. CO2 produced at these sources captured, compressed to supercritical pressures, transported via pipelines and stored in underground geologic formations such as depleted oil and natural gas reservoirs, un-minable coal seams and deep saline aquifers. In this work, we present the optimized pipeline infrastructure for the CO2 with appropriate constraints to find lower cost system by the use of nonlinear optimization software LINGO 11.0. This study was conducted on CO2 transportation complex network of Italian Industries, to find minimum cost network for transporting the CO2 from sources to the sinks.
Abstract: Internal controls of accounting are an essential
business function for a growth-oriented organization, and include the
elements of risk assessment, information communications and even
employees' roles and responsibilities. Internal controls of accounting
systems are designed to protect a company from fraud, abuse and
inaccurate data recording and help organizations keep track of
essential financial activities. Internal controls of accounting provide a
streamlined solution for organizing all accounting procedures and
ensuring that the accounting cycle is completed consistently and
successfully. Implementing a formal Accounting Procedures Manual
for the organization allows the financial department to facilitate
several processes and maintain rigorous standards. Internal controls
also allow organizations to keep detailed records, manage and
organize important financial transactions and set a high standard for
the organization's financial management structure and protocols. A
well-implemented system also reduces the risk of accounting errors
and abuse. A well-implemented controls system allows a company's
financial managers to regulate and streamline all functions of the
accounting department. Internal controls of accounting can be set up
for every area to track deposits, monitor check handling, keep track
of creditor accounts, and even assess budgets and financial statements
on an ongoing basis. Setting up an effective accounting system to
monitor accounting reports, analyze records and protect sensitive
financial information also can help a company set clear goals and
make accurate projections. Creating efficient accounting processes
allows an organization to set specific policies and protocols on
accounting procedures, and reach its financial objectives on a regular
basis. Internal accounting controls can help keep track of such areas
as cash-receipt recording, payroll management, appropriate recording
of grants and gifts, cash disbursements by authorized personnel, and
the recording of assets. These systems also can take into account any
government regulations and requirements for financial reporting.
Abstract: An economic operation scheduling problem of a
hydro-thermal power generation system has been properly solved by
the proposed multipath adaptive tabu search algorithm (MATS). Four
reservoirs with their own hydro plants and another one thermal plant
are integrated to be a studied system used to formulate the objective
function under complicated constraints, eg water managements,
power balance and thermal generator limits. MATS with four subsearch
units (ATSs) and two stages of discarding mechanism (DM),
has been setting and trying to solve the problem through 25 trials
under function evaluation criterion. It is shown that MATS can
provide superior results with respect to single ATS and other
previous methods, genetic algorithms (GA) and differential evolution
(DE).
Abstract: Intelligent deep-drawing is an instrumental research field in sheet metal forming. A set of 28 different experimental data have been employed in this paper, investigating the roles of die radius, punch radius, friction coefficients and drawing ratios for axisymmetric workpieces deep drawing. This paper focuses an evolutionary neural network, specifically, error back propagation in collaboration with genetic algorithm. The neural network encompasses a number of different functional nodes defined through the established principles. The input parameters, i.e., punch radii, die radii, friction coefficients and drawing ratios are set to the network; thereafter, the material outputs at two critical points are accurately calculated. The output of the network is used to establish the best parameters leading to the most uniform thickness in the product via the genetic algorithm. This research achieved satisfactory results based on demonstration of neural networks.
Abstract: In this study, a fuzzy-logic based control system was
designed to ensure that time and energy is saved during the operation
of load elevators which are used during the construction of tall
buildings. In the control system that was devised, for the load
elevators to work more efficiently, the energy interval where the
motor worked was taken as the output variable whereas the amount
of load and the building height were taken as input variables. The
most appropriate working intervals depending on the characteristics
of these variables were defined by the help of an expert. Fuzzy expert
system software was formed using Delphi programming language. In
this design, mamdani max-min inference mechanism was used and
the centroid method was employed in the clarification procedure. In
conclusion, it is observed that the system that was designed is
feasible and this is supported by statistical analyses..
Abstract: Modern information and communication technologies
offer a variety of support options for the efficient handling of
customer relationships. CRM systems have been developed, which
are designed to support the processes in the areas of marketing, sales
and service. Along with technological progress, CRM systems are
constantly changing, i.e. the systems are continually enhanced by
new functions. However, not all functions are suitable for every
company because of different frameworks and business processes. In
this context the question arises whether or not CRM systems are
widely used in Austrian companies and which business processes are
most frequently supported by CRM systems. This paper aims to shed
light on the popularity of CRM systems in Austrian companies in
general and the use of different functions to support their daily
business. First of all, the paper provides a theoretical overview of the
structure of modern CRM systems and proposes a categorization of
currently available software functionality for collaborative,
operational and analytical CRM processes, which provides the
theoretical background for the empirical study. Apart from these
theoretical considerations, the paper presents the empirical results of
a field survey on the use of CRM systems in Austrian companies and
analyzes its findings.
Abstract: Recently, several designs of single fed circularly
polarized microstrip antennas have been studied. Relatively, a few
designs for achieving circular polarization using triangular microstrip
antenna are available. Typically existing design of single fed
circularly polarized triangular microstrip antennas include the use of
equilateral triangular patch with a slit or a horizontal slot on the patch
or addition a narrow band stub on the edge or a vertex of triangular
patch.
In other word, with using a narrow band tune stub on middle of an
edge of triangle causes of facility to compensate the possible
fabrication error and substrate materials with easier adjusting the
tuner stub length. Even though disadvantages of this method is very
long of stub (approximate 1/3 length of triangle edge). In this paper,
instead of narrow band stub, a wide band stub has been applied,
therefore the length of stub by this method has been decreased
around 1/10 edge of triangle in addition changing the aperture angle
of stub, provides more facility for designing and producing circular
polarization wave.
Abstract: A data warehouse (DW) is a system which has value and role for decision-making by querying. Queries to DW are critical regarding to their complexity and length. They often access millions of tuples, and involve joins between relations and aggregations. Materialized views are able to provide the better performance for DW queries. However, these views have maintenance cost, so materialization of all views is not possible. An important challenge of DW environment is materialized view selection because we have to realize the trade-off between performance and view maintenance cost. Therefore, in this paper, we introduce a new approach aimed at solve this challenge based on Two-Phase Optimization (2PO), which is a combination of Simulated Annealing (SA) and Iterative Improvement (II), with the use of Multiple View Processing Plan (MVPP). Our experiments show that our method provides a further improvement in term of query processing cost and view maintenance cost.
Abstract: With the exponential growth of networked system and
application such as eCommerce, the demand for effective internet
security is increasing. Cryptology is the science and study of systems
for secret communication. It consists of two complementary fields of
study: cryptography and cryptanalysis. The application of genetic
algorithms in the cryptanalysis of knapsack ciphers is suggested by
Spillman [7]. In order to improve the efficiency of genetic algorithm
attack on knapsack cipher, the previously published attack was
enhanced and re-implemented with variation of initial assumptions
and results are compared with Spillman results. The experimental
result of research indicates that the efficiency of genetic algorithm
attack on knapsack cipher can be improved with variation of initial
assumption.
Abstract: We have defined two suites of metrics, which cover
static and dynamic aspects of component assembly. The static
metrics measure complexity and criticality of component assembly,
wherein complexity is measured using Component Packing Density
and Component Interaction Density metrics. Further, four criticality
conditions namely, Link, Bridge, Inheritance and Size criticalities
have been identified and quantified. The complexity and criticality
metrics are combined to form a Triangular Metric, which can be used
to classify the type and nature of applications. Dynamic metrics are
collected during the runtime of a complete application. Dynamic
metrics are useful to identify super-component and to evaluate the
degree of utilisation of various components. In this paper both static
and dynamic metrics are evaluated using Weyuker-s set of properties.
The result shows that the metrics provide a valid means to measure
issues in component assembly. We relate our metrics suite with
McCall-s Quality Model and illustrate their impact on product
quality and to the management of component-based product
development.
Abstract: Faced with social and health system capacity
constraints and rising and changing demand for welfare services,
governments and welfare providers are increasingly relying on
innovation to help support and enhance services. However, the
evidence reported by several studies indicates that the realization of
that potential is not an easy task. Innovations can be deemed
inherently complex to implement and operate, because many of them
involve a combination of technological and organizational renewal
within an environment featuring a diversity of stakeholders. Many
public welfare service innovations are markedly systemic in their
nature, which means that they emerge from, and must address, the
complex interplay between political, administrative, technological,
institutional and legal issues. This paper suggests that stakeholders
dealing with systemic innovation in welfare services must deal with
ambiguous and incomplete information in circumstances of
uncertainty. Employing a literature review methodology and case
study, this paper identifies, categorizes and discusses different
aspects of the uncertainty of systemic innovation in public welfare
services, and argues that uncertainty can be classified into eight
categories: technological uncertainty, market uncertainty,
regulatory/institutional uncertainty, social/political uncertainty,
acceptance/legitimacy uncertainty, managerial uncertainty, timing
uncertainty and consequence uncertainty.
Abstract: Currently, the Malaysian construction industry is
focusing on transforming construction processes from conventional
building methods to the Industrialized Building System (IBS). Still,
research on the decision making of IBS technology adoption with the
influence of contextual factors is scarce. The purpose of this paper is
to explore how contextual factors influence the IBS decision making
in building projects which is perceived by those involved in
construction industry namely construction stakeholders and IBS
supply chain members. Theoretical background, theoretical
frameworks and literatures which identify possible contextual factors
that influence decision making towards IBS technology adoption are
presented. This paper also discusses the importance of contextual
factors in IBS decision making, highlighting some possible crossover
benefits and making some suggestions as to how these can be
utilized. Conclusions are drawn and recommendations are made with
respect to the perception of socio-economic, IBS policy and IBS
technology associated with building projects.