Abstract: Nowadays, desalination of salt water is considered an important industrial process. In many parts of the world, particularly in the gulf countries, the multi-stage flash (MSF) water desalination has an essential contribution in the production of fresh water. In this study, a simple mathematical model is defined to design a MSF desalination system and the feasibility of using the MSF desalination process in proximity of a 42 MW power plant is investigated. This power plant can just provide 10 ton/h superheated steam from low pressure (LP) section of heat recovery steam generator (HRSG) for thermal desalting system. The designed MSF system with gained output ratio (GOR) of 10.3 has 24 flashing stages and can produce 2480 ton/d of fresh water. The expected performance characteristics of the designed MSF desalination plant are determined. In addition, the effect of motive water pressure on the amount of non-condensable gases removed by water jet vacuum pumps is investigated.
Abstract: In this study, numerical simulations on laminar flow in
sinusoidal wavy shaped tubes were conducted for mean Reynolds
number of 250, which is in the range of physiological flow-rate and
investigated flow structures, pressure distribution and particle
trajectories both in steady and periodic inflow conditions. For
extensive comparisons, various wave lengths and amplitudes of sine
function for geometry of tube models were employed. The results
showed that small amplitude secondary curvature has significant
influence on the nature of flow patterns and particle mixing
mechanism. This implies that characterizing accurate geometry is
essential in accurate predicting of in vivo hemodynamics and may
motivate further study on any possibility of reflection of secondary
flow on vascular remodeling and pathophysiology.
Abstract: In this work, simulation algorithms for contact drying
of agitated particulate materials under vacuum and at atmospheric
pressure were developed. The implementation of algorithms gives a
predictive estimation of drying rate curves and bulk bed temperature
during contact drying. The calculations are based on the penetration
model to describe the drying process, where all process parameters
such as heat and mass transfer coefficients, effective bed properties,
gas and liquid phase properties are estimated with proper
correlations. Simulation results were compared with experimental
data from the literature. In both cases, simulation results were in good
agreement with experimental data. Few deviations were identified
and the limitations of the predictive capabilities of the models are
discussed. The programs give a good insight of the drying behaviour
of the analysed powders.
Abstract: The purpose of this study is to discuss the effect of the
intervention of exercise behavior change plan for high school students
on study subjects- social and psychological factors and exercise
stages. This research uses the transtheoretical model as the research
framework. One experiment group and one control group were used in
a quasi-experimental design research. The experimental group
accepted health-related physical fitness course and the traditional
course; the control group accepted traditional physical education
course. There is a significant difference before and after the
intervention in the experimental group. Karl-s test shows the
experimental group gained a better improvement than that in the
control group. The Analysis of Covariance had shown the exercise
stages (F=7.62, p
Abstract: Simultaneous effects of temperature, immersion time, salt concentration, sucrose concentration, pressure and convective dryer temperature on the combined osmotic dehydration - convective drying of edible button mushrooms were investigated. Experiments were designed according to Central Composite Design with six factors each at five different levels. Response Surface Methodology (RSM) was used to determine the optimum processing conditions that yield maximum water loss and rehydration ratio and minimum solid gain and shrinkage in osmotic-convective drying of edible button mushrooms. Applying surfaces profiler and contour plots optimum operation conditions were found to be temperature of 39 °C, immersion time of 164 min, salt concentration of 14%, sucrose concentration of 53%, pressure of 600 mbar and drying temperature of 40 °C. At these optimum conditions, water loss, solid gain, rehydration ratio and shrinkage were found to be 63.38 (g/100 g initial sample), 3.17 (g/100 g initial sample), 2.26 and 7.15%, respectively.
Abstract: The quality and shelf life of foods of containing lipids (fats and oils) significantly reduces due to rancidity.Applications of natural antioxidants are one of the most effective manners to prevent the oxidation of oils and lipids. The antioxidant properties of juice extracted from barberry fruit (Berberris vulgaris.L) using maceration and SWE (10 bars and 120 - 180°C) methods were investigated and compared with conventional method. The amount of phenolic compound and reduction power of all samples were determined and the data were statistically analyzed using multifactor design. The results showed that the total amount of phenolic compound increased with increasing of pressure and temprature from 1861.9 to 2439.1 (mg Gallic acid /100gr Dry matter). The ability of reduction power of SWE obtained antioxidant extract compared with BHA (synthetic antioxidant) and ascorbic acid (natural antioxidant). There were significant differences among reduction power of extracts and there were remarkable difference with BHA and Ascorbic acid (P
Abstract: A new dual-fluid concept was studied that could eventually find application for cold-gas propulsion for small space satellites or other constant flow applications. In basic form, the concept uses two different refrigerant working fluids, each having a different saturation vapor pressure. The higher vapor pressure refrigerant remains in the saturation phase and is used to pressurize the lower saturation vapor pressure fluid (the propellant) which remains in the compressed liquid phase. A demonstration thruster concept based on this principle was designed and built to study its operating characteristics. An automotive-type electronic fuel injector was used to meter and deliver the propellant. Ejected propellant mass and momentum were measured for several combinations of refrigerants and hydrocarbon fluids. The thruster has the advantage of delivering relatively large total impulse at low tank pressure within a small volume.
Abstract: The present work analyses different parameters of pressure die casting to minimize the casting defects. Pressure diecasting is usually applied for casting of aluminium alloys. Good surface finish with required tolerances and dimensional accuracy can be achieved by optimization of controllable process parameters such as solidification time, molten temperature, filling time, injection pressure and plunger velocity. Moreover, by selection of optimum process parameters the pressure die casting defects such as porosity, insufficient spread of molten material, flash etc. are also minimized. Therefore, a pressure die casting component, carburetor housing of aluminium alloy (Al2Si2O5) has been considered. The effects of selected process parameters on casting defects and subsequent setting of parameters with the levels have been accomplished by Taguchi-s parameter design approach. The experiments have been performed as per the combination of levels of different process parameters suggested by L18 orthogonal array. Analyses of variance have been performed for mean and signal-to-noise ratio to estimate the percent contribution of different process parameters. Confidence interval has also been estimated for 95% consistency level and three conformational experiments have been performed to validate the optimum level of different parameters. Overall 2.352% reduction in defects has been observed with the help of suggested optimum process parameters.
Abstract: The flow field over a three dimensional pole barn
characterized by a cylindrical roof has been numerically investigated.
Wind pressure and viscous loads acting on the agricultural building
have been analyzed for several incoming wind directions, so as to
evaluate the most critical load condition on the structure. A constant
wind velocity profile, based on the maximum reference wind speed in
the building site (peak gust speed worked out for 50 years return
period) and on the local roughness coefficient, has been simulated.
In order to contemplate also the hazard due to potential air
wedging between the stored hay and the lower part of the ceiling, the
effect of a partial filling of the barn has been investigated.
The distribution of wind-induced loads on the structure have been
determined, allowing a numerical quantification of the effect of wind
direction on the induced stresses acting on a hemicylindrical roof.
Abstract: The aerodynamic noise radiation from a side view mirror (SVM) in the high-speed airflow is calculated by the combination of unsteady incompressible fluid flow analysis and acoustic analysis. The transient flow past the generic SVM is simulated with variable turbulence model, namely DES Detached Eddy Simulation and LES (Large Eddy Simulation). Detailed velocity vectors and contour plots of the time-varying velocity and pressure fields are presented along cut planes in the flow-field. Mean and transient pressure are also monitored at several points in the flow field and compared to corresponding experimentally data published in literature. The acoustic predictions made using the Ffowcs-Williams-Hawkins acoustic analogy (FW-H) and the boundary element (BEM).
Abstract: The flow and heat transfer mechanism in convex
corrugated tubes have been investigated through numerical
simulations in this paper. Two kinds of tube types named as symmetric
corrugated tube (SCT) and asymmetric corrugated tube (ACT) are
modeled and studied numerically based on the RST model. The
predictive capability of RST model is examined in the corrugation wall
in order to check the reliability of RST model under the corrugation
wall condition. We propose a comparison between the RST modelling
the corrugation wall with existing direct numerical simulation of Maaß
C and Schumann U [14]. The numerical results pressure coefficient at
different profiles between RST and DNS are well matched. The
influences of large corrugation tough radii to heat transfer and flow
characteristic had been considered. Flow and heat transfer comparison
between SCT and ACT had been discussed. The numerical results
show that ACT exhibits higher overall heat transfer performance than
SCT.
Abstract: Simultaneous effects of temperature, immersion time, salt concentration, sucrose concentration, pressure and convective dryer temperature on the combined osmotic dehydration - convective drying of edible button mushrooms were investigated. Experiments were designed according to Central Composite Design with six factors each at five different levels. Response Surface Methodology (RSM) was used to determine the optimum processing conditions that yield maximum water loss and rehydration ratio and minimum solid gain and shrinkage in osmotic-convective drying of edible button mushrooms. Applying surfaces profiler and contour plots optimum operation conditions were found to be temperature of 39 °C, immersion time of 164 min, salt concentration of 14%, sucrose concentration of 53%, pressure of 600 mbar and drying temperature of 40 °C. At these optimum conditions, water loss, solid gain, rehydration ratio and shrinkage were found to be 63.38 (g/100 g initial sample), 3.17 (g/100 g initial sample), 2.26 and 7.15%, respectively.
Abstract: The objective of this research is to examine the shear thinning behaviour of mixing flow of non-Newtonian fluid like toothpaste in the dissolution container with rotating stirrer. The problem under investigation is related to the chemical industry. Mixing of fluid is performed in a cylindrical container with rotating stirrer, where stirrer is eccentrically placed on the lid of the container. For the simulation purpose the associated motion of the fluid is considered as revolving of the container, with stick stirrer. For numerical prediction, a time-stepping finite element algorithm in a cylindrical polar coordinate system is adopted based on semi-implicit Taylor-Galerkin/pressure-correction scheme. Numerical solutions are obtained for non-Newtonian fluids employing power law model. Variations with power law index have been analysed, with respect to the flow structure and pressure drop.
Abstract: We have developed a computer program consisting of
6 subtests assessing the children hand dexterity applicable in the
rehabilitation medicine. We have carried out a normative study on a
representative sample of 285 children aged from 7 to 15 (mean age
11.3) and we have proposed clinical standards for three age groups
(7-9, 9-11, 12-15 years). We have shown statistical significance of
differences among the corresponding mean values of the task time
completion. We have also found a strong correlation between the task
time completion and the age of the subjects, as well as we have
performed the test-retest reliability checks in the sample of 84
children, giving the high values of the Pearson coefficients for the
dominant and non-dominant hand in the range 0.740.97 and
0.620.93, respectively.
A new MATLAB-based programming tool aiming at analysis of
cardiologic RR intervals and blood pressure descriptors, is worked
out, too. For each set of data, ten different parameters are extracted: 2
in time domain, 4 in frequency domain and 4 in Poincaré plot
analysis. In addition twelve different parameters of baroreflex
sensitivity are calculated. All these data sets can be visualized in time
domain together with their power spectra and Poincaré plots. If
available, the respiratory oscillation curves can be also plotted for
comparison. Another application processes biological data obtained
from BLAST analysis.
Abstract: This paper reports the influence of sucrose on the
preservation of CO2 hydrate crystal samples. The particle diameter of
hydrate samples were 1.0 and 5.6-8.0 mm. Mass fraction of sucrose in
the sample was 0.16. The samples were stored at the aerated condition
under atmospheric pressure and at the temperature of 253 or 258 K.
The results indicated that the mass fractions of CO2 hydrate in the
samples with sucrose were 0.10 ± 0.03 at the end of 3-week
preservation, regardless of temperature and particle diameter. Mass
fraction of CO2 hydrate in the samples with sucrose was higher than
that of pure CO2 hydrate for 1.0 mm particle diameter, while was
lower than that of pure CO2 hydrate for 5.6-8.0 mm particle diameter.
Discussion is made on the influence of sucrose on the dissociation of
CO2 hydrate and the resulting formation of ice.
Abstract: Vernonia divergens Benth., commonly known as
“Insulin Plant” (Fam: Asteraceae) is a potent sugar killer. Locally the
leaves of the plant, boiled in water are successfully administered to a
large number of diabetic patients. The present study evaluates the
putative anti-diabetic ingredients, isolated from the in vivo and in
vitro grown plantlets of V. divergens for their antimicrobial and
anticancer activities. Sterilized explants of nodal segments were
cultured on MS (Musashige and Skoog, 1962) medium in presence of
different combinations of hormones. Multiple shoots along with
bunch of roots were regenerated at 1mg l-1 BAP and 0.5 mg l-1 NAA.
Micro-plantlets were separated and sub-cultured on the double
strength (2X) of the above combination of hormones leading to
increased length of roots and shoots. These plantlets were
successfully transferred to soil and survived well in nature. The
ethanol extract of plantlets from both in vivo & in vitro sources were
prepared in soxhlet extractor and then concentrated to dryness under
reduced pressure in rotary evaporator. Thus obtainedconcentrated
extracts showed significant inhibitory activity against gram
negative bacteria like Escherichia coli and Pseudomonas
aeruginosa but no inhibition was found against gram positive
bacteria. Further, these ethanol extracts were screened for in vitro
percentage cytotoxicity at different time periods (24 h, 48 h and 72 h)
of different dilutions. The in vivo plant extract inhibited the growth of
EAC mouse cell lines in the range of 65, 66, 78, and 88% at 100, 50,
25 & 12.5μg mL-1 but at 72 h of treatment. In case of the extract of in
vitro origin, the inhibition was found against EAC cell lines even at
48h. During spectrophotometric scanning, the extracts exhibited
different maxima (ʎ) - four peaks in in vitro extracts as against single
in in vivo preparation suggesting the possible change in the nature of
ingredients during micropropagation through tissue culture
techniques.
Abstract: Triglycerides and their derivatives are considered as viable alternatives for diesel fuels. Rice bran oil is used as diesel fuel. Highly viscous rice bran oil can be reduced by blending it with diesel fuel. The present research is aimed to investigate experimentally the performance, exhaust emission and combustion characteristics of a direct injection (DI) diesel engine, typically used in agricultural sector, over the entire load range when fuelled with rice bran oil and diesel fuel blends, RB10 (10% rice bran oil + 90% diesel fuel) to RB50. The performance, emission and combustion parameters of RB20 were found to be very close to neat diesel fuel (ND). The injector opening pressure (IOP) undoubtedly is of prime importance in diesel engine operation. Performance, emission and combustion characteristics with RB30 at enhanced IOPs are better than ND. Improved premixed heat release rate were noticed with RB30 when the IOP is enhanced.
Abstract: Solid oxide fuel cells have been considered in the last years as one of the most promising technologies for very highefficiency electric energy generation from hydrogen or other hydrocarbons, both with simple fuel cell plants and with integrated gas turbine-fuel cell systems. In the present study, a detailed thermodynamic analysis has been carried out. Mass and exergy balances are performed not only for the whole plant but also for each component in order to evaluate the thermal efficiency of combined cycle. Moreover, different sources of irreversibilities within the SOFC stack have been discussed and a parametric study conducted to evaluate the effect of temperature as well as pressure on SOFC irreversibilities and its performance. In this investigation methane and hydrogen have been used for fueling the SOFC stack and combustion chamber.
Abstract: The counter flow solar air heaters, with four
transverse fins and wire mesh layers are constructed and investigated
experimentally for thermal efficiency at a geographic location of
Cyprus in the city of Famagusta. The absorber plate is replaced by
sixteen steel wire mesh layers, 0.18 x 0.18cm in cross section
opening and a 0.02cm in diameter. The wire mesh layers arranged in
three groups, first and second include 6 layers, while the third include
4 layers. All layers fixed in the duct parallel to the glazing and each
group separated from the others by wood frame thickness of 0.5cm to
reduce the pressure drop. The transverse fins arranged in a way to
force the air to flow through the bed like eight letter path with flow
depth 3cm. The proposed design has increased the heat transfer rate,
but on other hand causes a high pressure drop. The obtained results
show that, for air mass flow rate range between 0.011-0.036kg/s, the
thermal efficiency increases with increasing the air mass flow. The
maximum efficiency obtained is 65.6% for the mass flow rate of
0.036kg/s. Moreover, the temperature difference between the outlet
flow and the ambient temperature, ΔT, reduces as the air mass flow
rate increase. The maximum difference between the outlet and
ambient temperature obtained was 43°C for double pass for minimum
mass flow rate of 0.011kg/s. Comparison with a conventional solar
air heater collector shows a significantly development in the thermal
efficiency.
Abstract: Carbon dioxide capture process has been simulated
and studied under different process conditions. It has been shown
that several process parameters such as lean amine temperature,
number of adsorber stages, number of stripper stages and stripper
pressure affect different process conditions and outputs such as
carbon dioxide removal and reboiler duty. It may be concluded that
the simulation of carbon dioxide capture process can help to estimate
the best process conditions.