Abstract: In this study, a three dimensional numerical heat
transfer model has been used to simulate the laser structuring of
polymer substrate material in the Three-Dimensional Molded
Interconnect Device (3D MID) which is used in the advanced multifunctional
applications. A finite element method (FEM) transient
thermal analysis is performed using APDL (ANSYS Parametric
Design Language) provided by ANSYS. In this model, the effect of
surface heat source was modeled with Gaussian distribution, also the
effect of the mixed boundary conditions which consist of convection
and radiation heat transfers have been considered in this analysis. The
model provides a full description of the temperature distribution, as
well as calculates the depth and the width of the groove upon material
removal at different set of laser parameters such as laser power and
laser speed. This study also includes the experimental procedure to
study the effect of laser parameters on the depth and width of the
removal groove metal as verification to the modeled results. Good
agreement between the experimental and the model results is
achieved for a wide range of laser powers. It is found that the quality
of the laser structure process is affected by the laser scan speed and
laser power. For a high laser structured quality, it is suggested to use
laser with high speed and moderate to high laser power.
Abstract: In development of floating photovoltaic generation
system, finding a suitable place of installation is as important as
development of economically feasible and stable structure. Especially
since floating photovoltaic system has its facility floating on water
surface, it is extremely important to review the effects of weather
conditions such as wind, water flow and floating matters, various
factors (such as fogs) that can reduce generation efficiency, possibility
of connection with power system, and legal restrictions. The method of
investigating suitable area and resource for development of
tracking-type floating photovoltaic generation system was proposed in
this paper, which can be used for development of floating and ocean
photovoltaic system in the future.
Abstract: The mineral bioflotation represents a viable
alternative for the evaluation of new processes benefit alternative.
The adsorption bacteria on minerals surfaces will depend mainly on
the type of the microorganism as well as of the studied mineral
surface. In the current study, adhesion of S. carnosus on coal was
studied. Several methods were used as: DRX, Fourier Transform
Infra-Red (FTIR) adhesion isotherms and kinetic. The main goal is to
recovery of organic matter by the microflotation process on coal
particles with biological reagent (S. carnosus). Adhesion tests
revealed that adhesion took place after of 8 h at pH 9. The results
suggest that the adhesion of bacteria to solid substrates can be
considered an abiotic physicochemical process that is consequently
governed by bacterial surface properties such as their specific surface
area, hydrophobicity and surface functionalities. The greatest coal
fine flotability was of 75%, after 5 min of flotation.
Abstract: This research proposes a novel reconstruction protocol
for restoring missing surfaces and low-quality edges and shapes in
photos of artifacts at historical sites. The protocol starts with the
extraction of a cloud of points. This extraction process is based on
four subordinate algorithms, which differ in the robustness and
amount of resultant. Moreover, they use different -but
complementary- accuracy to some related features and to the way
they build a quality mesh. The performance of our proposed protocol
is compared with other state-of-the-art algorithms and toolkits. The
statistical analysis shows that our algorithm significantly outperforms
its rivals in the resultant quality of its object files used to reconstruct
the desired model.
Abstract: This paper presents a 3D guidance scheme for
Unmanned Aerial Vehicles (UAVs). The proposed guidance scheme
is based on the sliding mode approach using nonlinear sliding
manifolds. Generalized 3D kinematic equations are considered
here during the design process to cater for the coupling between
longitudinal and lateral motions. Sliding mode based guidance
scheme is then derived for the multiple-input multiple-output
(MIMO) system using the proposed nonlinear manifolds. Instead of
traditional sliding surfaces, nonlinear sliding surfaces are proposed
here for performance and stability in all flight conditions. In the
reaching phase control inputs, the bang-bang terms with signum
functions are accompanied with proportional terms in order to reduce
the chattering amplitudes. The Proposed 3D guidance scheme is
implemented on a 6-degrees-of-freedom (6-dof) simulation of a UAV
and simulation results are presented here for different 3D trajectories
with and without disturbances.
Abstract: One of the most important tasks in urban remote
sensing is the detection of impervious surfaces (IS), such as roofs and
roads. However, detection of IS in heterogeneous areas still remains
one of the most challenging tasks. In this study, detection of concrete
roof using an object-based approach was proposed. A new rule-based
classification was developed to detect concrete roof tile. This
proposed rule-based classification was applied to WorldView-2
image and results showed that the proposed rule has good potential to
predict concrete roof material from WorldView-2 images, with 85%
accuracy.
Abstract: A generalized vortex lattice method for complex
lifting surfaces with flap and aileron deflection is formulated. The
method is not restricted by the linearized theory assumption and
accounts for all standard geometric lifting surface parameters:
camber, taper, sweep, washout, dihedral, in addition to flap and
aileron deflection. Thickness is not accounted for since the physical
lifting body is replaced by a lattice of panels located on the mean
camber surface. This panel lattice setup and the treatment of different
wake geometries is what distinguish the present work form the
overwhelming majority of previous solutions based on the vortex
lattice method. A MATLAB code implementing the proposed
formulation is developed and validated by comparing our results to
existing experimental and numerical ones and good agreement is
demonstrated. It is then used to study the accuracy of the widely used
classical vortex-lattice method. It is shown that the classical approach
gives good agreement in the clean configuration but is off by as much
as 30% when a flap or aileron deflection of 30° is imposed. This
discrepancy is mainly due the linearized theory assumption
associated with the conventional method. A comparison of the effect
of four different wake geometries on the values of aerodynamic
coefficients was also carried out and it is found that the choice of the
wake shape had very little effect on the results.
Abstract: Three dimensional non-Interlaced carbon fibre
reinforced silicon carbide (3-D-Cf/SiC) composites with pyrocarbon
interphase were fabricated using isothermal chemical vapor
infiltration (ICVI) combined with polymer impregnation pyrolysis
(PIP) process. Polysilazane (PSZ) is used as a preceramic polymer to
obtain silicon carbide matrix. Thermo gravimetric analysis (TGA),
Infrared spectroscopic analysis (IR) and X-ray diffraction (XRD)
analysis were carried out on PSZ pyrolysed at different temperatures
to understand the pyrolysis and obtaining the optimum pyrolysing
condition to yield β-SiC phase. The density of the composites was
1.94 g cm-3 after the 3-D carbon preform was SiC infiltrated for 280 h
with one intermediate polysilazane pre-ceramic PIP process.
Mechanical properties of the composite materials were investigated
under tensile, flexural, shear and impact loading. The values of
tensile strength were 200 MPa at room temperature (RT) and 195
MPa at 500°C in air. The average RT flexural strength was 243 MPa.
The lower flexural strength of these composites is because of the
porosity. The fracture toughness obtained from single edge notched
beam (SENB) technique was 39 MPa.m1/2. The work of fracture
obtained from the load-displacement curve of SENB test was 22.8
kJ.m-2. The composites exhibited excellent impact resistance and the
dynamic fracture toughness of 44.8 kJ.m-2 is achieved as determined
from instrumented Charpy impact test. The shear strength of the
composite was 93 MPa, which is significantly higher compared 2-D
Cf/SiC composites. Microstructure evaluation of fracture surfaces
revealed the signatures of fracture processes and showed good
support for the higher toughness obtained.
Abstract: This study aimed at designing and developing a
mechanical force gauge for the square watermelon mold for the first
time. It also tried to introduce the square watermelon characteristics
and its production limitations. The mechanical force gauge
performance and the product itself were also described. There are
three main designable gauge models: a. hydraulic gauge, b. strain
gauge, and c. mechanical gauge. The advantage of the hydraulic
model is that it instantly displays the pressure and thus the force
exerted by the melon. However, considering the inability to measure
forces at all directions, complicated development, high cost, possible
hydraulic fluid leak into the fruit chamber and the possible influence
of increased ambient temperature on the fluid pressure, the
development of this gauge was overruled. The second choice was to
calculate pressure using the direct force a strain gauge. The main
advantage of these strain gauges over spring types is their high
precision in measurements; but with regard to the lack of conformity
of strain gauge working range with water melon growth, calculations
were faced with problems. Finally the mechanical pressure gauge has
advantages, including the ability to measured forces and pressures on
the mold surface during melon growth; the ability to display the peak
forces; the ability to produce melon growth graph thanks to its
continuous force measurements; the conformity of its manufacturing
materials with the required physical conditions of melon growth; high
air conditioning capability; the ability to permit sunlight reaches the
melon rind (no yellowish skin and quality loss); fast and
straightforward calibration; no damages to the product during
assembling and disassembling; visual check capability of the product
within the mold; applicable to all growth environments (field,
greenhouses, etc.); simple process; low costs and so forth.
Abstract: Lightning protection systems (LPS) for wind power
generation is becoming an important public issue. A serious damage
of blades, accidents where low-voltage and control circuit
breakdowns are frequently occur in many wind farms. A grounding
system is one of the most important components required for
appropriate LPSs in wind turbines WTs. Proper design of a wind
turbine grounding system is demanding and several factors for the
proper and effective implementation must taken into account. In this
paper proposed procedure of proper design of grounding systems for
a wind turbine was introduced. This procedure depends on measuring
of ground current of simulated wind farm under lightning taking into
consideration the soil ionization. The procedure also includes the
Ground Potential Rise (GPR) and the voltage distributions at ground
surface level and Touch potential. In particular, the contribution of
mitigating techniques, such as rings, rods and the proposed design
were investigated.
Abstract: In the present work, detailed analysis on flow characteristics of a pair of immiscible liquids through horizontal pipeline is simulated by using ANSYS FLUENT 6.2. Moderately viscous oil and water (viscosity ratio = 107, density ratio = 0.89 and interfacial tension = 0.024 N/m) have been taken as system fluids for the study. Volume of Fluid (VOF) method has been employed by assuming unsteady flow, immiscible liquid pair, constant liquid properties, and co-axial flow. Meshing has been done using GAMBIT. Quadrilateral mesh type has been chosen to account for the surface tension effect more accurately. From the grid independent study, we have selected 47037 number of mesh elements for the entire geometry. Simulation successfully predicts slug, stratified wavy, stratified mixed and annular flow, except dispersion of oil in water, and dispersion of water in oil. Simulation results are validated with horizontal literature data and good conformity is observed. Subsequently, we have simulated the hydrodynamics (viz., velocity profile, area average pressure across a cross section and volume fraction profile along the radius) of stratified wavy and annular flow at different phase velocities. The simulation results show that in the annular flow, total pressure of the mixture decreases with increase in oil velocity due to the fact that pipe cross section is completely wetted with water. Simulated oil volume fraction shows maximum at the centre in core annular flow, whereas, in stratified flow, maximum value appears at upper side of the pipeline. These results are in accord with the actual flow configuration. Our findings could be useful in designing pipeline for transportation of crude oil.
Abstract: The mixed convection stagnation point flow toward a vertical plate is investigated. The external flow impinges normal to the heated plate and the surface temperature is assumed to vary linearly with the distance from the stagnation point. The governing partial differential equations are transformed into a set of ordinary differential equations, which are then solved numerically using MATLAB routine boundary value problem solver bvp4c. Numerical results show that dual solutions are possible for a certain range of the mixed convection parameter. A stability analysis is performed to determine which solution is linearly stable and physically realizable.
Abstract: This paper presents the findings of an experimental investigation of important machining parameters for the horizontal boring tool modified to mouth with a horizontal lathe machine to bore an overlength workpiece. In order to verify a usability of a modified tool, design of experiment based on Taguchi method is performed. The parameters investigated are spindle speed, feed rate, depth of cut and length of workpiece. Taguchi L9 orthogonal array is selected for four factors three level parameters in order to minimize surface roughness (Ra and Rz) of S45C steel tubes. Signal to noise ratio analysis and analysis of variance (ANOVA) is performed to study an effect of said parameters and to optimize the machine setting for best surface finish. The controlled factors with most effect are depth of cut, spindle speed, length of workpiece, and feed rate in order. The confirmation test is performed to test the optimal setting obtained from Taguchi method and the result is satisfactory.
Abstract: When it comes to last, it is regarded as the critical foundation of shoe design and development. Not only the last relates to the comfort of shoes wearing but also it aids the production of shoe styling and manufacturing. In order to enhance the efficiency and application of last development, a computer aided methodology for customized last form designs is proposed in this study. The reverse engineering is mainly applied to the process of scanning for the last form. Then the minimum energy is used for the revision of surface continuity, the surface of the last is reconstructed with the feature curves of the scanned last. When the surface of a last is reconstructed, based on the foundation of the proposed last form reconstruction module, the weighted arithmetic mean method is applied to the calculation on the shape morphing which differs from the grading for the control mesh of last, and the algorithm of subdivision is used to create the surface of last mesh, thus the feet-fitting 3D last form of different sizes is generated from its original form feature with functions remained. Finally, the practicability of the proposed methodology is verified through later case studies.
Abstract: Vertical slotted walls can be used as permeable
breakwaters to provide economical and environmental protection
from undesirable waves and currents inside the port. The permeable
breakwaters are partially protection and have been suggested to
overcome the environmental disadvantages of fully protection
breakwaters. For regular waves a semi-analytical model is based on
an eigenfunction expansion method and utilizes a boundary condition
at the surface of each wall are developed to detect the energy
dissipation through the slots. Extensive laboratory tests are carried
out to validate the semi-analytic models. The structure of the physical
model contains two walls and it consists of impermeable upper and
lower part, where the draft is based a decimal multiple of the total
depth. The middle part is permeable with a porosity of 50%. The
second barrier is located at a distant of 0.5, 1, 1.5 and 2 times of the
water depth from the first one. A comparison of the theoretical results
with previous studies and experimental measurements of the present
study show a good agreement and that, the semi-analytical model is
able to adequately reproduce most the important features of the
experiment.
Abstract: This research aimed to study on the efficiency of wastewater treatment by comparing the different aeration times of surface aerators in Suan Sunandha Rajabhat University. In doing so, the operation of surface aerators was divided into 2 groups which included the groups of 8 hours (8-0/opened-closed) and 4 hours (2-2/opened-closed) of aeration time per day. As a result of the study, it was found that the efficiency of wastewater treatment in the forms of DO, BOD, turbidity and NO2- by 8 hours (8-0/opened-closed) and 4 hours (2-2/opened-closed) of aeration time per day of surface aerators was not statistically different [Sig. = .644, .488, .716 and .054 > α (.05)] while the efficiency in the forms of NO3- and P was significantly different at the statistical level of .01 [Sig. = .001 and .000 < α (.01)].
Abstract: High resolution seismic reflection has recently been carried out on Zaria batholith, with the aim of characterizing the granitic Zaria batholiths in terms of its lithology. The geology of the area has revealed that the older granite outcrops in the vicinity of Zaria are exposures of a syntectonics to late-tectonic granite batholiths which intruded a crystalline gneissic basement during the Pan-African Orogeny. During the data acquisition the geophone were placed at interval of 1 m, variable offset of 1 and 10 m was used. The common midpoint (CMP) method with 12 fold coverage was employed for the survey. Analysis of the generated 3D surface of the p wave velocities from different profiles for densities and bulk modulus revealed that the rock material is more consolidated in South East part of the batholith and less consolidated in the North Western part. This was in conformity with earlier identified geology of the area, with the South Eastern part majorly of granitic outcrop, while the North Western part is characterized with the exposure of gneisses and thick overburden cover. The difference in lithology was also confirmed by the difference in seismic sections and Arial satellite photograph. Hence two major lithologies were identified, the granitic and gneisses complex which are characterized by gradational boundaries.
Abstract: This study presents the numerical simulation of three-dimensional incompressible steady and laminar fluid flow and conjugate heat transfer of a trapezoidal microchannel heat sink using water as a cooling fluid in a silicon substrate. Navier-Stokes equations with conjugate energy equation are discretized by finite-volume method. We perform numerical computations for a range of 50 ≦ Re ≦ 600, 0.05W ≦ P ≦ 0.8W, 20W/cm2 ≦q"≦ 40W/cm2. The present study demonstrates the numerical optimization of a trapezoidal microchannel heat sink design using the response surface methodology (RSM) and the genetic algorithm method (GA). The results show that the average Nusselt number increases with an increase in the Reynolds number or pumping power, and the thermal resistance decreases as the pumping power increases. The thermal resistance of a trapezoidal microchannel is minimized for a constant heat flux and constant pumping power.
Abstract: The impact deformation and fracture behaviour of cobalt-based Haynes 188 superalloy are investigated by means of a split Hopkinson pressure bar. Impact tests are performed at strain rates ranging from 1×103 s-1 to 5×103 s-1 and temperatures between 25°C and 800°C. The experimental results indicate that the flow response and fracture characteristics of cobalt-based Haynes 188 superalloy are significantly dependent on the strain rate and temperature. The flow stress, work hardening rate and strain rate sensitivity all increase with increasing strain rate or decreasing temperature. It is shown that the impact response of the Haynes 188 specimens is adequately described by the Zerilli-Armstrong fcc model. The fracture analysis results indicate that the Haynes 188 specimens fail predominantly as the result of intensive localised shearing. Furthermore, it is shown that the flow localisation effect leads to the formation of adiabatic shear bands. The fracture surfaces of the deformed Haynes 188 specimens are characterised by dimple- and / or cleavage-like structure with knobby features. The knobby features are thought to be the result of a rise in the local temperature to a value greater than the melting point.
Abstract: In this study, Electrical Discharge Machining (EDM) is used to modify the surface of high carbon steel En31 with the help of tool electrode (Copper-Chromium-Nickel) manufactured by powder metallurgy (PM) process. The effect of EDM on surface roughness during surface alloying is studied. Taguchi’s Design of experiment (DOE) and L18 orthogonal array is used to find the best level of input parameters in order to achieve high surface finish. Six input parameters are considered and their percentage contribution towards surface roughness is investigated by analysis of variances (ANOVA). Experimental results show that an hard alloyed surface (1.21% carbon, 2.14% chromium and 1.38% nickel) with surface roughness of 3.19µm can be generated using EDM with PM tool. Additionally, techniques like Scanning Electron Microscope (SEM) and Energy Dispersive Spectroscopy (EDS) are used to analyze the machined surface and EDMed layer composition, respectively. The increase in machined surface micro-hardness (101%) may be related to the formation of carbides containing chromium.