Abstract: The special and unique advantages of explosive
forming, has developed its use in different industries. Considering the
important influence of improving the current explosive forming
techniques on increasing the efficiency and control over the
explosive forming procedure, the effects of air and water as the
energy-conveying medium, and also their differences will be
illustrated in this paper. Hence, a large number of explosive forming
tests have been conducted on two sizes of thin walled cylindrical
shells by using air and water as the working medium. Comparative
diagrams of the maximum radial deflection of work-pieces of the
same size, as a function of the scaled distance, show that for the
points with the same values of scaled distance, the maximum radial
deformation caused by the under water explosive loading is 4 to 5
times more than the deflection of the shells under explosive forming,
while using air. Results of this experimental research have also been
compared with other studies which show that using water as the
energy conveying media increases the efficiency up to 4.8 times. The
effect of the media on failure modes of the shells, and the necking
mechanism of the walls of the specimens, while being explosively
loaded, are also discussed in this issue. Measuring the tested
specimens shows that, the increase in the internal volume has been
accompanied by necking of the walls, which finally results in the
radial rupture of the structure.
Abstract: In this paper we propose a multi-agent architecture for web information retrieval using fuzzy logic based result fusion mechanism. The model is designed in JADE framework and takes advantage of JXTA agent communication method to allow agent communication through firewalls and network address translators. This approach enables developers to build and deploy P2P applications through a unified medium to manage agent-based document retrieval from multiple sources.
Abstract: Omni directional mobile robots have been popularly
employed in several applications especially in soccer player robots
considered in Robocup competitions. However, Omni directional
navigation system, Omni-vision system and solenoid kicking
mechanism in such mobile robots have not ever been combined. This
situation brings the idea of a robot with no head direction into
existence, a comprehensive Omni directional mobile robot. Such a
robot can respond more quickly and it would be capable for more
sophisticated behaviors with multi-sensor data fusion algorithm for
global localization base on the data fusion. This paper has tried to
focus on the research improvements in the mechanical, electrical and
software design of the robots of team ADRO Iran. The main
improvements are the world model, the new strategy framework,
mechanical structure, Omni-vision sensor for object detection, robot
path planning, active ball handling mechanism and the new kicker
design, , and other subjects related to mobile robot
Abstract: IEEE 802.11e is the enhanced version of the IEEE
802.11 MAC dedicated to provide Quality of Service of wireless
network. It supports QoS by the service differentiation and
prioritization mechanism. Data traffic receives different priority
based on QoS requirements. Fundamentally, applications are divided
into four Access Categories (AC). Each AC has its own buffer queue
and behaves as an independent backoff entity. Every frame with a
specific priority of data traffic is assigned to one of these access
categories. IEEE 802.11e EDCA (Enhanced Distributed Channel
Access) is designed to enhance the IEEE 802.11 DCF (Distributed
Coordination Function) mechanisms by providing a distributed
access method that can support service differentiation among
different classes of traffic. Performance of IEEE 802.11e MAC layer
with different ACs is evaluated to understand the actual benefits
deriving from the MAC enhancements.
Abstract: Delamination between layers in composite materials is a major structural failure. The delamination resistance is quantified by the critical strain energy release rate (SERR). The present investigation deals with the strain energy release rate of two woven fabric composites. Materials used are made of two types of glass fiber (360 gsm and 600 gsm) of plain weave and epoxy as matrix. The fracture behavior is studied using the mode I, double cantilever beam test and the mode II, end notched flexure test, in order to determine the energy required for the initiation and growth of an artificial crack. The delamination energy of these two materials is compared in order to study the effect of weave and reinforcement on mechanical properties. The fracture mechanism is also analyzed by means of scanning electron microscopy (SEM). It is observed that the plain weave fabric composite with lesser strand width has higher inter laminar fracture properties compared to the plain weave fabric composite with more strand width.
Abstract: This paper makes an attempt to solve the problem of
searching and retrieving of similar MRI photos via Internet services
using morphological features which are sourced via the original
image. This study is aiming to be considered as an additional tool of
searching and retrieve methods. Until now the main way of the
searching mechanism is based on the syntactic way using keywords.
The technique it proposes aims to serve the new requirements of
libraries. One of these is the development of computational tools for
the control and preservation of the intellectual property of digital
objects, and especially of digital images. For this purpose, this paper
proposes the use of a serial number extracted by using a previously
tested semantic properties method. This method, with its center being
the multi-layers of a set of arithmetic points, assures the following
two properties: the uniqueness of the final extracted number and the
semantic dependence of this number on the image used as the
method-s input. The major advantage of this method is that it can
control the authentication of a published image or its partial
modification to a reliable degree. Also, it acquires the better of the
known Hash functions that the digital signature schemes use and
produces alphanumeric strings for cases of authentication checking,
and the degree of similarity between an unknown image and an
original image.
Abstract: In this paper, a theoretical formula is presented to
predict the instantaneous folding force of the first fold creation in a
square column under axial loading. Calculations are based on analysis
of “Basic Folding Mechanism" introduced by Wierzbicki and
Abramowicz. For this purpose, the sum of dissipated energy rate under
bending around horizontal and inclined hinge lines and dissipated
energy rate under extensional deformations are equated to the work rate
of the external force on the structure. Final formula obtained in this
research, reasonably predicts the instantaneous folding force of the first
fold creation versus folding distance and folding angle and also predicts
the instantaneous folding force instead of the average value. Finally,
according to the calculated theoretical relation, instantaneous folding
force of the first fold creation in a square column was sketched
versus folding distance and was compared to the experimental results
which showed a good correlation.
Abstract: In theoretical computer science, the Turing machine has played a number of important roles in understanding and exploiting basic concepts and mechanisms in computing and information processing [20]. It is a simple mathematical model of computers [9]. After that, M.Blum and C.Hewitt first proposed two-dimensional automata as a computational model of two-dimensional pattern processing, and investigated their pattern recognition abilities in 1967 [7]. Since then, a lot of researchers in this field have been investigating many properties about automata on a two- or three-dimensional tape. On the other hand, the question of whether processing fourdimensional digital patterns is much more difficult than two- or threedimensional ones is of great interest from the theoretical and practical standpoints. Thus, the study of four-dimensional automata as a computasional model of four-dimensional pattern processing has been meaningful [8]-[19],[21]. This paper introduces a cooperating system of four-dimensional finite automata as one model of four-dimensional automata. A cooperating system of four-dimensional finite automata consists of a finite number of four-dimensional finite automata and a four-dimensional input tape where these finite automata work independently (in parallel). Those finite automata whose input heads scan the same cell of the input tape can communicate with each other, that is, every finite automaton is allowed to know the internal states of other finite automata on the same cell it is scanning at the moment. In this paper, we mainly investigate some accepting powers of a cooperating system of eight- or seven-way four-dimensional finite automata. The seven-way four-dimensional finite automaton is an eight-way four-dimensional finite automaton whose input head can move east, west, south, north, up, down, or in the fu-ture, but not in the past on a four-dimensional input tape.
Abstract: Earthquakes produce some of the most violent loading
situations that a structure can be subjected to and if a structure fails
under these loads then inevitably human life is put at risk. One of the
most common methods by which a structure fails under seismic
loading is at the connection of structural elements. The research
presented in this paper investigates the interlock systems as a novel
method for building structures. The main objective of this
experimental study wasto determine the dynamic characteristics and
the seismic behaviour of the proposed structures compared to
conventional structural systemsduring seismic motions. Results of
this study indicate that the interlock mechanism of the panels
influences the behaviour of lateral load-resisting systems of the
structures during earthquakes, contributing to better structural
flexibility and easier maintenance.
Abstract: In recent years application of natural antimicrobials
instead of conventional ones, due to their hazardous effects on health,
has got serious attentions. On the basis of the results of different
studies, chitosan, a natural bio-degradable and non-toxic
biopolysaccharide derived from chitin, has potential to be used as a
natural antimicrobial. Chitosan has exhibited high antimicrobial
activity against a wide variety of pathogenic and spoilage
microorganisms, including fungi, and Gram-positive and Gramnegative
bacteria. The antimicrobial action is influenced by intrinsic
factors such as the type of chitosan, the degree of chitosan
polymerization and extrinsic factors such as the microbial organism,
the environmental conditions and presence of the other components.
The use of chitosan in food systems should be based on sufficient
knowledge of the complex mechanisms of its antimicrobial mode of
action. In this article we review a number of studies on the
investigation of chitosan antimicrobial properties and application of
them in culture and food mediums.
Abstract: A steady two-phase flow model has been developed to simulate the drying process of porous particle in a pneumatic conveying dryer. The model takes into account the momentum, heat and mass transfer between the continuous phase and the dispersed phase. A single particle model was employed to calculate the evaporation rate. In this model the pore structure is simplified to allow the dominant evaporation mechanism to be readily identified at all points within the duct. The predominant mechanism at any time depends upon the pressure, temperature and the diameter of pore from which evaporating is occurring. The model was validated against experimental studies of pneumatic transport at low and high speeds as well as pneumatic drying. The effects of operating conditions on the dryer parameters are studied numerically. The present results show that the drying rate is enhanced as the inlet gas temperature and the gas flow rate increase and as the solid mass flow rate deceases. The present results also demonstrate the necessity of measuring the inlet gas velocity or the solid concentration in any experimental analysis.
Abstract: Continuously growing needs for Internet applications
that transmit massive amount of data have led to the emergence of
high speed network. Data transfer must take place without any
congestion and hence feedback parameters must be transferred from
the receiver end to the sender end so as to restrict the sending rate in
order to avoid congestion. Even though TCP tries to avoid
congestion by restricting the sending rate and window size, it never
announces the sender about the capacity of the data to be sent and
also it reduces the window size by half at the time of congestion
therefore resulting in the decrease of throughput, low utilization of
the bandwidth and maximum delay. In this paper, XCP protocol is
used and feedback parameters are calculated based on arrival rate,
service rate, traffic rate and queue size and hence the receiver
informs the sender about the throughput, capacity of the data to be
sent and window size adjustment, resulting in no drastic decrease in
window size, better increase in sending rate because of which there is
a continuous flow of data without congestion. Therefore as a result of
this, there is a maximum increase in throughput, high utilization of
the bandwidth and minimum delay. The result of the proposed work
is presented as a graph based on throughput, delay and window size.
Thus in this paper, XCP protocol is well illustrated and the various
parameters are thoroughly analyzed and adequately presented.
Abstract: Although water only takes a little percentage in the total mass of soil, it indeed plays an important role to the strength of structure. Moisture transfer can be carried out by many different mechanisms which may involve heat and mass transfer, thermodynamic phase change, and the interplay of various forces such as viscous, buoyancy, and capillary forces. The continuum models are not well suited for describing those phenomena in which the connectivity of the pore space or the fracture network, or that of a fluid phase, plays a major role. However, Lattice Boltzmann methods (LBMs) are especially well suited to simulate flows around complex geometries. Lattice Boltzmann methods were initially invented for solving fluid flows. Recently, fluid with multicomponent and phase change is also included in the equations. By comparing the numerical result with experimental result, the Lattice Boltzmann methods with phase change will be optimized.
Abstract: In the following text, we show that by introducing
universal kinetic scheme, the origin of rate retardation and inhibition
period which observed in dithiobenzoate-mediated RAFT
polymerization can be described properly. We develop our model by
utilizing the method of moments, then we apply our model to
different monomer/RAFT agent systems, both homo- and
copolymerization. The modeling results are in an excellent
agreement with experiments and imply the validity of universal
kinetic scheme, not only for dithiobenzoate-mediated systems, but
also for different types of monomer/RAFT agent ones.
Abstract: Evolvable hardware (EHW) refers to a selfreconfiguration
hardware design, where the configuration is under
the control of an evolutionary algorithm (EA). A lot of research has
been done in this area several different EA have been introduced.
Every time a specific EA is chosen for solving a particular problem,
all its components, such as population size, initialization, selection
mechanism, mutation rate, and genetic operators, should be selected
in order to achieve the best results. In the last three decade a lot of
research has been carried out in order to identify the best parameters
for the EA-s components for different “test-problems". However
different researchers propose different solutions. In this paper the
behaviour of mutation rate on (1+λ) evolution strategy (ES) for
designing logic circuits, which has not been done before, has been
deeply analyzed. The mutation rate for an EHW system modifies
values of the logic cell inputs, the cell type (for example from AND
to NOR) and the circuit output. The behaviour of the mutation has
been analyzed based on the number of generations, genotype
redundancy and number of logic gates used for the evolved circuits.
The experimental results found provide the behaviour of the mutation
rate to be used during evolution for the design and optimization of
logic circuits. The researches on the best mutation rate during the last
40 years are also summarized.
Abstract: This paper proposes an alternative control mechanism
for an interactive Pan/Tilt/Zoom (PTZ) camera control system.
Instead of using a mouse or a joystick, the proposed mechanism
utilizes a Nintendo Wii remote and infrared (IR) sensor bar. The Wii
remote has buttons that allows the user to control the movement of a
PTZ camera through Bluetooth connectivity. In addition, the Wii
remote has a built-in motion sensor that allows the user to give
control signals to the PTZ camera through pitch and roll movement.
A stationary IR sensor bar, placed at some distance away opposite the
Wii remote, enables the detection of yaw movement. In addition, the
Wii remote-s built-in IR camera has the ability to detect its spatial
position, and thus generates a control signal when the user moves the
Wii remote. Some experiments are carried out and their performances
are compared with an industry-standard PTZ joystick.
Abstract: Ovshinsky initiated scientific research in the field of
amorphous and disordered materials that continues to this day. The
Ovshinsky Effect where the resistance of thin GST films is
significantly reduced upon the application of low voltage is of
fundamental importance in phase-change - random access memory
(PC-RAM) devices.GST stands for GdSbTe chalcogenide type
glasses.However, the Ovshinsky Effect is not without controversy.
Ovshinsky thought the resistance of GST films is reduced by the
redistribution of charge carriers; whereas, others at that time including
many PC-RAM researchers today argue that the GST resistance
changes because the GST amorphous state is transformed to the
crystalline state by melting, the heat supplied by external heaters. In
this controversy, quantum mechanics (QM) asserts the heat capacity of
GST films vanishes, and therefore melting cannot occur as the heat
supplied cannot be conserved by an increase in GST film
temperature.By precluding melting, QM re-opens the controversy
between the melting and charge carrier mechanisms. Supporting
analysis is presented to show that instead of increasing GST film
temperature, conservation proceeds by the QED induced creation of
photons within the GST film, the QED photons confined by TIR. QED
stands for quantum electrodynamics and TIR for total internal
reflection. The TIR confinement of QED photons is enhanced by the
fact the absorbedheat energy absorbed in the GST film is concentrated
in the TIR mode because of their high surface to volume ratio. The
QED photons having Planck energy beyond the ultraviolet produce
excitons by the photoelectric effect, the electrons and holes of which
reduce the GST film resistance.
Abstract: Nurses in an Armed Force Hospital (AFH) expose to stronger stress than those in a civil hospital, especially in an emergency department (ED). Ironically, stresses of these nurses received few if any attention in academic research in the past. This study collects 227 samples from the emergency departments of four armed force hospitals in central and southern Taiwan. The research indicates that the top five stressors are a massive casualty event, delayed physician support, overloads of routine work, overloads of assignments, and annoying paper work. Excessive work loading was found to be the primary source of stress. Nurses who were perceived to have greater stress levels were more inclined to deploy emotion-oriented approaches and more likely to seek job rotations. Professional stressors and problem-oriented approaches were positively correlated. Unlike other local studies, this study concludes that the excessive work-loading is more stressful in an AFH.
Abstract: In an open real-time system environment, the coexistence of different kinds of real-time and non real-time applications makes the system scheduling mechanism face new requirements and challenges. One two-level scheduling scheme of the open real-time systems is introduced, and points out that hard and soft real-time applications are scheduled non-distinctively as the same type real-time applications, the Quality of Service (QoS) cannot be guaranteed. It has two flaws: The first, it can not differentiate scheduling priorities of hard and soft real-time applications, that is to say, it neglects characteristic differences between hard real-time applications and soft ones, so it does not suit a more complex real-time environment. The second, the worst case execution time of soft real-time applications cannot be predicted exactly, so it is not worth while to cost much spending in order to assure all soft real-time applications not to miss their deadlines, and doing that may cause resource wasting. In order to solve this problem, a novel two-level real-time scheduling mechanism (including scheduling profile and scheduling algorithm) which adds the process of dealing with soft real-time applications is proposed. Finally, we verify real-time scheduling mechanism from two aspects of theory and experiment. The results indicate that our scheduling mechanism can achieve the following objectives. (1) It can reflect the difference of priority when scheduling hard and soft real-time applications. (2) It can ensure schedulability of hard real-time applications, that is, their rate of missing deadline is 0. (3) The overall rate of missing deadline of soft real-time applications can be less than 1. (4) The deadline of a non-real-time application is not set, whereas the scheduling algorithm that server 0 S uses can avoid the “starvation" of jobs and increase QOS. By doing that, our scheduling mechanism is more compatible with different types of applications and it will be applied more widely.
Abstract: Titanium alloys like the modern alloy Ti 6Al 2Sn 4Zr 6Mo (Ti-6246) combine excellent specific mechanical properties and corrosion resistance. On the other hand,due to their material characteristics, machining of these alloys is difficult to perform. The aim of the current study is the analyses of wear mechanisms of coated cemented carbide tools applied in orthogonal cutting experiments of Ti-6246 alloy. Round bars were machined with standard coated tools in dry conditions on a CNC latheusing a wide range of cutting speeds and cutting depths. Tool wear mechanisms were afterwards investigated by means of stereo microscopy, optical microscopy, confocal microscopy and scanning electron microscopy. Wear mechanisms included fracture of the tool tip (total failure) and abrasion. Specific wear features like crater wear, micro cracks and built-up edgeformation appeared depending of the mechanical and thermal conditions generated in the workpiece surface by the cutting action.