Abstract: Hydrogen is an important chemical in many industries
and it is expected to become one of the major fuels for energy
generation in the future. Unfortunately, hydrogen does not exist in its
elemental form in nature and therefore has to be produced from
hydrocarbons, hydrogen-containing compounds or water.
Above its critical point (374.8oC and 22.1MPa), water has lower
density and viscosity, and a higher heat capacity than those of
ambient water. Mass transfer in supercritical water (SCW) is
enhanced due to its increased diffusivity and transport ability. The
reduced dielectric constant makes supercritical water a better solvent
for organic compounds and gases. Hence, due to the aforementioned
desirable properties, there is a growing interest toward studies
regarding the gasification of organic matter containing biomass or
model biomass solutions in supercritical water.
In this study, hydrogen and biofuel production by the catalytic
gasification of 2-Propanol in supercritical conditions of water was
investigated. Pt/Al2O3and Ni/Al2O3were the catalysts used in the
gasification reactions. All of the experiments were performed under a
constant pressure of 25MPa. The effects of five reaction temperatures
(400, 450, 500, 550 and 600°C) and five reaction times (10, 15, 20,
25 and 30 s) on the gasification yield and flammable component
content were investigated.
Abstract: This paper solves the environmental/ economic dispatch
power system problem using the Non-dominated Sorting Genetic
Algorithm-II (NSGA-II) and its hybrid with a Convergence Accelerator
Operator (CAO), called the NSGA-II/CAO. These multiobjective
evolutionary algorithms were applied to the standard IEEE 30-bus
six-generator test system. Several optimization runs were carried out
on different cases of problem complexity. Different quality measure
which compare the performance of the two solution techniques were
considered. The results demonstrated that the inclusion of the CAO
in the original NSGA-II improves its convergence while preserving
the diversity properties of the solution set.
Abstract: Irradiated material is a typical example of a complex
system with nonlinear coupling between its elements. During
irradiation the radiation damage is developed and this development
has bifurcations and qualitatively different kinds of behavior.
The accumulation of primary defects in irradiated crystals is
considered in frame work of nonlinear evolution of complex system.
The thermo-concentration nonlinear feedback is carried out as a
mechanism of self-oscillation development.
It is shown that there are two ways of the defect density evolution
under stationary irradiation. The first is the accumulation of defects;
defect density monotonically grows and tends to its stationary state
for some system parameters. Another way that takes place for
opportune parameters is the development of self-oscillations of the
defect density.
The stationary state, its stability and type are found. The
bifurcation values of parameters (environment temperature, defect
generation rate, etc.) are obtained. The frequency of the selfoscillation
and the conditions of their development is found and
rated. It is shown that defect density, heat fluxes and temperature
during self-oscillations can reach much higher values than the
expected steady-state values. It can lead to a change of typical
operation and an accident, e.g. for nuclear equipment.
Abstract: LABVIEW is a graphical programming language that has its roots in automation control and data acquisition. In this paper we have utilized this platform to provide a powerful toolset for process identification and control of nonlinear systems based on artificial neural networks (ANN). This tool has been applied to the monitoring and control of a lab-scale distillation column DELTALAB DC-SP. The proposed control scheme offers high speed of response for changes in set points and null stationary error for dual composition control and shows robustness in presence of externally imposed disturbance.
Abstract: In this paper we have proposed a methodology to
develop an amperometric biosensor for the analysis of glucose
concentration using a simple microcontroller based data acquisition
system. The work involves the development of Detachable
Membrane Unit (enzyme based biomembrane) with immobilized
glucose oxidase on the membrane and interfacing the same to the
signal conditioning system. The current generated by the biosensor
for different glucose concentrations was signal conditioned, then
acquired and computed by a simple AT89C51-microcontroller. The
optimum operating parameters for the better performance were found
and reported. The detailed performance evaluation of the biosensor
has been carried out. The proposed microcontroller based biosensor
system has the sensitivity of 0.04V/g/dl, with a resolution of
50mg/dl. It has exhibited very good inter day stability observed up to
30 days. Comparing to the reference method such as HPLC, the
accuracy of the proposed biosensor system is well within ± 1.5%.
The system can be used for real time analysis of glucose
concentration in the field such as, food and fermentation and clinical
(In-Vitro) applications.
Abstract: Based on the homotopy perturbation method (HPM)
and Padé approximants (PA), approximate and exact solutions are
obtained for cubic Boussinesq and modified Boussinesq equations.
The obtained solutions contain solitary waves, rational solutions.
HPM is used for analytic treatment to those equations and PA for
increasing the convergence region of the HPM analytical solution.
The results reveal that the HPM with the enhancement of PA is a
very effective, convenient and quite accurate to such types of partial
differential equations.
Abstract: Collaborative working environments for distance
education can be considered as a more generic form of contemporary
remote labs. At present, the majority of existing real laboratories are
not constructed to allow the involved participants to collaborate in
real time. To make this revolutionary learning environment possible
we must allow the different users to carry out an experiment
simultaneously. In recent times, multi-user environments are
successfully applied in many applications such as air traffic control
systems, team-oriented military systems, chat-text tools, multi-player
games etc. Thus, understanding the ideas and techniques behind these
systems could be of great importance in the contribution of ideas to
our e-learning environment for collaborative working. In this
investigation, collaborative working environments from theoretical
and practical perspectives are considered in order to build an
effective collaborative real laboratory, which allows two students or
more to conduct remote experiments at the same time as a team. In
order to achieve this goal, we have implemented distributed system
architecture, enabling students to obtain an automated help by either
a human tutor or a rule-based e-tutor.
Abstract: In this paper we discuss the effect of unbounded particle interaction operator on particle growth and we study how this can address the choice of appropriate time steps of the numerical simulation. We provide also rigorous mathematical proofs showing that large particles become dominating with increasing time while small particles contribute negligibly. Second, we discuss the efficiency of the algorithm by performing numerical simulations tests and by comparing the simulated solutions with some known analytic solutions to the Smoluchowski equation.
Abstract: In this paper we present a hybrid search algorithm for
solving constraint satisfaction and optimization problems. This
algorithm combines ideas of two basic approaches: complete and
incomplete algorithms which also known as systematic search and
local search algorithms. Different characteristics of systematic search
and local search methods are complementary. Therefore we have
tried to get the advantages of both approaches in the presented
algorithm. The major advantage of presented algorithm is finding
partial sound solution for complicated problems which their complete
solution could not be found in a reasonable time. This algorithm
results are compared with other algorithms using the well known
n-queens problem.
Abstract: Partial discharge (PD) detection is an important
method to evaluate the insulation condition of metal-clad apparatus.
Non-intrusive sensors which are easy to install and have no
interruptions on operation are preferred in onsite PD detection.
However, it often lacks of accuracy due to the interferences in PD
signals. In this paper a novel PD extraction method that uses frequency
analysis and entropy based time-frequency (TF) analysis is introduced.
The repetitive pulses from convertor are first removed via frequency
analysis. Then, the relative entropy and relative peak-frequency of
each pulse (i.e. time-indexed vector TF spectrum) are calculated and
all pulses with similar parameters are grouped. According to the
characteristics of non-intrusive sensor and the frequency distribution
of PDs, the pulses of PD and interferences are separated. Finally the
PD signal and interferences are recovered via inverse TF transform.
The de-noised result of noisy PD data demonstrates that the
combination of frequency and time-frequency techniques can
discriminate PDs from interferences with various frequency
distributions.
Abstract: Quality of Service (QoS) Routing aims to find path between source and destination satisfying the QoS requirements which efficiently using the network resources and underlying routing algorithm and to fmd low-cost paths that satisfy given QoS constraints. One of the key issues in providing end-to-end QoS guarantees in packet networks is determining feasible path that satisfies a number of QoS constraints. We present a Optimized Multi- Constrained Routing (OMCR) algorithm for the computation of constrained paths for QoS routing in computer networks. OMCR applies distance vector to construct a shortest path for each destination with reference to a given optimization metric, from which a set of feasible paths are derived at each node. OMCR is able to fmd feasible paths as well as optimize the utilization of network resources. OMCR operates with the hop-by-hop, connectionless routing model in IP Internet and does not create any loops while fmding the feasible paths. Nodes running OMCR not necessarily maintaining global view of network state such as topology, resource information and routing updates are sent only to neighboring nodes whereas its counterpart link-state routing method depend on complete network state for constrained path computation and that incurs excessive communication overhead.
Abstract: In digital signal processing it is important to
approximate multi-dimensional data by the method called rank
reduction, in which we reduce the rank of multi-dimensional data from
higher to lower. For 2-dimennsional data, singular value
decomposition (SVD) is one of the most known rank reduction
techniques. Additional, outer product expansion expanded from SVD
was proposed and implemented for multi-dimensional data, which has
been widely applied to image processing and pattern recognition.
However, the multi-dimensional outer product expansion has behavior
of great computation complex and has not orthogonally between the
expansion terms. Therefore we have proposed an alterative method,
Third-order Orthogonal Tensor Product Expansion short for 3-OTPE.
3-OTPE uses the power method instead of nonlinear optimization
method for decreasing at computing time. At the same time the group
of B. D. Lathauwer proposed Higher-Order SVD (HOSVD) that is
also developed with SVD extensions for multi-dimensional data.
3-OTPE and HOSVD are similarly on the rank reduction of
multi-dimensional data. Using these two methods we can obtain
computation results respectively, some ones are the same while some
ones are slight different. In this paper, we compare 3-OTPE to
HOSVD in accuracy of calculation and computing time of resolution,
and clarify the difference between these two methods.
Abstract: Ontology is widely being used as a tool for organizing
information, creating the relation between the subjects within the
defined knowledge domain area. Various fields such as Civil,
Biology, and Management have successful integrated ontology in
decision support systems for managing domain knowledge and to
assist their decision makers. Gross pollutant traps (GPT) are devices
used in trapping and preventing large items or hazardous particles in
polluting and entering our waterways. However choosing and
determining GPT is a challenge in Malaysia as there are inadequate
GPT data repositories being captured and shared. Hence ontology is
needed to capture, organize and represent this knowledge into
meaningful information which can be contributed to the efficiency of
GPT selection in Malaysia urbanization. A GPT Ontology framework
is therefore built as the first step to capture GPT knowledge which
will then be integrated into the decision support system. This paper
will provide several examples of the GPT ontology, and explain how
it is constructed by using the Protégé tool.
Abstract: Circle grid space filling plate is a flow conditioner with a fractal pattern and used to eliminate turbulence originating from pipe fittings in experimental fluid flow applications. In this paper, steady state, incompressible, swirling turbulent flow through circle grid space filling plate has been studied. The solution and the analysis were carried out using finite volume CFD solver FLUENT 6.2. Three turbulence models were used in the numerical investigation and their results were compared with the pressure drop correlation of BS EN ISO 5167-2:2003. The turbulence models investigated here are the standard k-ε, realizable k-ε, and the Reynolds Stress Model (RSM). The results showed that the RSM model gave the best agreement with the ISO pressure drop correlation. The effects of circle grids space filling plate thickness and Reynolds number on the flow characteristics have been investigated as well.
Abstract: The development of shape and size of a crack in a
pressure vessel under uniaxial and biaxial loadings is important in
fitness-for-service evaluations such as leak-before-break. In this
work finite element modelling was used to evaluate the mean stress
and the J-integral around a front of a surface-breaking crack. A
procedure on the basis of ductile tearing resistance curves of high and
low constrained fracture mechanics geometries was developed to
estimate the amount of ductile crack extension for surface-breaking
cracks and to show the evolution of the initial crack shape. The
results showed non-uniform constraint levels and crack driving forces
around the crack front at large deformation levels. It was also shown
that initially semi-elliptical surface cracks under biaxial load
developed higher constraint levels around the crack front than in
uniaxial tension. However similar crack shapes were observed with
more extensions associated with cracks under biaxial loading.
Abstract: We demonstrate single-photon interference over 10 km using a plug and play system for quantum key distribution. The quality of the interferometer is measured by using the interferometer
visibility. The coding of the signal is based on the phase coding and the value of visibility is based on the interference effect, which result a number of count. The setup gives full control of polarization inside
the interferometer. The quality measurement of the interferometer is based on number of count per second and the system produces 94 % visibility in one of the detectors.
Abstract: Feature selection study is gaining importance due to its contribution to save classification cost in terms of time and computation load. In search of essential features, one of the methods to search the features is via the decision tree. Decision tree act as an intermediate feature space inducer in order to choose essential features. In decision tree-based feature selection, some studies used decision tree as a feature ranker with a direct threshold measure, while others remain the decision tree but utilized pruning condition that act as a threshold mechanism to choose features. This paper proposed threshold measure using Manhattan Hierarchical Cluster distance to be utilized in feature ranking in order to choose relevant features as part of the feature selection process. The result is promising, and this method can be improved in the future by including test cases of a higher number of attributes.
Abstract: Personal computers draw non-sinusoidal current
with odd harmonics more significantly. Power Quality of
distribution networks is severely affected due to the flow of these
generated harmonics during the operation of electronic loads. In
this paper, mathematical modeling of odd harmonics in current like
3rd, 5th, 7th and 9th influencing the power quality has been presented.
Live signals have been captured with the help of power quality
analyzer for analysis purpose. The interesting feature is that Total
Harmonic Distortion (THD) in current decreases with the increase
of nonlinear loads has been verified theoretically. The results
obtained using mathematical expressions have been compared with
the practical results and exciting results have been found.
Abstract: Simultaneous transient conduction and radiation heat
transfer with heat generation is investigated. Analysis is carried out
for both steady and unsteady situations. two-dimensional gray
cylindrical enclosure with an absorbing, emitting, and isotropically
scattering medium is considered. Enclosure boundaries are assumed
at specified temperatures. The heat generation rate is considered
uniform and constant throughout the medium. The lattice Boltzmann
method (LBM) was used to solve the energy equation of a transient
conduction-radiation heat transfer problem. The control volume finite
element method (CVFEM) was used to compute the radiative
information. To study the compatibility of the LBM for the energy
equation and the CVFEM for the radiative transfer equation, transient
conduction and radiation heat transfer problems in 2-D cylindrical
geometries were considered. In order to establish the suitability of the
LBM, the energy equation of the present problem was also solved
using the the finite difference method (FDM) of the computational
fluid dynamics. The CVFEM used in the radiative heat transfer was
employed to compute the radiative information required for the
solution of the energy equation using the LBM or the FDM (of the
CFD). To study the compatibility and suitability of the LBM for the
solution of energy equation and the CVFEM for the radiative
information, results were analyzed for the effects of various
parameters such as the boundary emissivity. The results of the LBMCVFEM
combination were found to be in excellent agreement with
the FDM-CVFEM combination. The number of iterations and the
steady state temperature in both of the combinations were found
comparable. Results are found for situations with and without heat
generation. Heat generation is found to have significant bearing on
temperature distribution.
Abstract: The weight constrained shortest path problem
(WCSPP) is one of most several known basic problems in
combinatorial optimization. Because of its importance in many areas
of applications such as computer science, engineering and operations
research, many researchers have extensively studied the WCSPP.
This paper mainly concentrates on the reduction of total search space
for finding WCSP using some existing Genetic Algorithm (GA). For
this purpose, some controlled schemes of genetic operators are
adopted on list chromosome representation. This approach gives a
near optimum solution with smaller elapsed generation than classical
GA technique. From further analysis on the matter, a new
generalized schema theorem is also developed from the philosophy
of Holland-s theorem.