Abstract: Although the field of parametric Pattern Recognition (PR) has been thoroughly studied for over five decades, the use of the Order Statistics (OS) of the distributions to achieve this has not been reported. The pioneering work on using OS for classification was presented in [1] for the Uniform distribution, where it was shown that optimal PR can be achieved in a counter-intuitive manner, diametrically opposed to the Bayesian paradigm, i.e., by comparing the testing sample to a few samples distant from the mean. This must be contrasted with the Bayesian paradigm in which, if we are allowed to compare the testing sample with only a single point in the feature space from each class, the optimal strategy would be to achieve this based on the (Mahalanobis) distance from the corresponding central points, for example, the means. In [2], we showed that the results could be extended for a few symmetric distributions within the exponential family. In this paper, we attempt to extend these results significantly by considering asymmetric distributions within the exponential family, for some of which even the closed form expressions of the cumulative distribution functions are not available. These distributions include the Rayleigh, Gamma and certain Beta distributions. As in [1] and [2], the new scheme, referred to as Classification by Moments of Order Statistics (CMOS), attains an accuracy very close to the optimal Bayes’ bound, as has been shown both theoretically and by rigorous experimental testing.
Abstract: The present study was carried out to evaluate the
nutritional value of sorghum flour during processing of injera
(unleavened thick bread). The proximate composition of sorghum
flour before and after fermentation and that of injera was determined.
Compared to the raw flour and fermented one, injera had low protein
(11.55%), ash (1.57%) and fat (2.40%) contents but high in fiber
content. Moreover, injera was found to have significantly (P ≤ 0.05)
higher energy (389.08 Kcal/100g) compared to raw and fermented
sorghum flour. Injera contained lower levels of anti-nutritional
factors (polyphenols, phytate and tannins) compared to raw and
fermented sorghum. Also it was found to be rich in Ca
(4.75mg/100g), Fe (3.95 mg/100g), and Cu (0.7 mg/100g) compared
to that of raw and fermented flour. Moreover, both the extractable
minerals and protein digestibility were high for injera due to low
amount of anti-nutrients. Injera was found to contain an appreciable
amount of amino acids except arginine and tyrosine.
Abstract: The effect of cross linking of the protein isolates of
three legumes with the microbial enzyme transglutaminase (EC
2.3.2.13) on the functional properties at different NaCl concentration
was studied. The reduction in the total free amino groups (OD340) of
the polymerized protein showed that TGase treatment cross-linking
the protein subunit of each legume. The solubility of the protein
polymer of each legume was greatly improved at high concentration
of NaCl. At 1.2 M NaCl the solubility of the native legumes protein
was significantly decreased but after polymerization slightly
improved. Cross linked proteins were less turbid on heating to higher
temperature as compared to native proteins and the temperature at
which the protein turns turbid also increased in the polymerized
proteins. The emulsifying and foaming properties of the protein
polymer were greatly improved at all concentrations of NaCl for all
legumes.
Abstract: The information on the Web increases tremendously.
A number of search engines have been developed for searching Web
information and retrieving relevant documents that satisfy the
inquirers needs. Search engines provide inquirers irrelevant
documents among search results, since the search is text-based rather
than semantic-based. Information retrieval research area has
presented a number of approaches and methodologies such as
profiling, feedback, query modification, human-computer interaction,
etc for improving search results. Moreover, information retrieval has
employed artificial intelligence techniques and strategies such as
machine learning heuristics, tuning mechanisms, user and system
vocabularies, logical theory, etc for capturing user's preferences and
using them for guiding the search based on the semantic analysis
rather than syntactic analysis. Although a valuable improvement has
been recorded on search results, the survey has shown that still
search engines users are not really satisfied with their search results.
Using ontologies for semantic-based searching is likely the key
solution. Adopting profiling approach and using ontology base
characteristics, this work proposes a strategy for finding the exact
meaning of the query terms in order to retrieve relevant information
according to user needs. The evaluation of conducted experiments
has shown the effectiveness of the suggested methodology and
conclusion is presented.
Abstract: The studying of enzymatic esterification of carboxylic
acids and higher alcohols was performed by esterase Saccharomyces
cerevisiae in water-organic medium. Investigation of the enzyme
specificity to acetic substrates showed the best result with acetic acid
in esterification reactions with ethanol whereas within other
carboxylic acids the esterification decreased with acids: hexanoic >
pentanoic > butyric > decanoic. In relation to higher alcohols C3-C5,
esterification increased with alcohols propanol < butanol < amylol.
Also it was determined that esterase was more specific to alcohols
with branched chain such as isobutyl alcohol and isoamyl alcohol.
Data obtained may have important practical implications, for
example, for application of yeast esterase in producing various
volatile esters as well as in enzymatic transformation of volatile acids
and toxic fusel alcohols into volatile esters by providing the
production of the high quality alcoholic beverages with redused
content of higher alcohols as well as with improved degustational and
hygienic properties.
Abstract: The very nonlinear nature of the generator and system
behaviour following a severe disturbance precludes the use of
classical linear control technique. In this paper, a new approach of
nonlinear control is proposed for transient and steady state stability
analysis of a synchronous generator. The control law of the generator
excitation is derived from the basis of Lyapunov stability criterion.
The overall stability of the system is shown using Lyapunov
technique. The application of the proposed controller to simulated
generator excitation control under a large sudden fault and wide
range of operating conditions demonstrates that the new control
strategy is superior to conventional automatic voltage regulator
(AVR), and show very promising results.
Abstract: Business Process Management (BPM) helps in optimizing the business processes inside an enterprise. But BPM architecture does not provide any help for extending the enterprise. Modern business environments and rapidly changing technologies are asking for brisk changes in the business processes. Service Oriented Architecture (SOA) can help in enabling the success of enterprise-wide BPM. SOA supports agility in software development that is directly related to achieve loose coupling of interacting software agents. Agility is a premium concern of the current software designing architectures. Together, BPM and SOA provide a perfect combination for enterprise computing. SOA provides the capabilities for services to be combined together and to support and create an agile, flexible enterprise. But there are still many questions to answer; BPM is better or SOA? and what is the future track of BPM and SOA? This paper tries to answer some of these important questions.
Abstract: The Constraints imposed by non-thermal
leptogenesis on the survival of the neutrino mass models describing
the presently available neutrino mass patterns, are studied
numerically. We consider the Majorana CP violating phases coming
from right-handed Majorana mass matrices to estimate the baryon
asymmetry of the universe, for different neutrino mass models
namely quasi-degenerate, inverted hierarchical and normal
hierarchical models, with tribimaximal mixings. Considering two
possible diagonal forms of Dirac neutrino mass matrix as either
charged lepton or up-quark mass matrix, the heavy right-handed
mass matrices are constructed from the light neutrino mass matrix.
Only the normal hierarchical model leads to the best predictions of
baryon asymmetry of the universe, consistent with observations in
non-thermal leptogenesis scenario.
Abstract: The objective of this paper is to present a
comparative study of Homotopy Perturbation Method (HPM),
Variational Iteration Method (VIM) and Homotopy Analysis
Method (HAM) for the semi analytical solution of Kortweg-de
Vries (KdV) type equation called KdV. The study have been
highlighted the efficiency and capability of aforementioned methods
in solving these nonlinear problems which has been arisen from a
number of important physical phenomenon.
Abstract: Quality of school meals is one of the major concerns of governments and international organizations worldwide. This study aims to evaluate nutritional compliance of meals served at a Portuguese primary school considering the portions stated by Portuguese Education Ministry. To evaluate adequacy of portions served, weighing of all meal components offered to students and leftovers was performed during ten consecutive days at two different moments. Plate waste (%) was calculated by the ratio of food discarded and food served to the children. Nutritional evaluation of menus was made using the Portuguese Food Composition Table. Meals evaluated showed a percent contribution to energetic daily intake higher than recommendations. Meals served to children were considered high energy and protein dense. No significant waste of soup was accounted and the main meal components wasted were fish and vegetables. It will be necessary to adjust portions indicated by Ministry of Education in order to comply with recommendations and reduce food waste.
Abstract: Due to adverse pressure gradient along the diverging
walls of wide-angled diffusers, the attached flow separates from
one wall and remains attached permanently to the other wall in a
process called stalling. Stalled diffusers render the whole fluid flow
system, in which they are part of, very inefficient. There is then an
engineering need to try to understand the whole process of diffuser
stall if any meaningful attempts to improve on diffuser efficiency
are to be made. In this regard, this paper provides a data bank
contribution for the mean flow-field in wide-angled diffusers where
the complete velocity and static pressure fields, and pressure recovery
data for diffusers in the fully stalled flow regime are experimentally
measured. The measurements were carried out at Reynolds numbers
between 1.07×105 and 2.14×105 based on inlet hydraulic diameter
and centreline velocity for diffusers whose divergence angles were
between 30Ôùª and 50Ôùª. Variation of Reynolds number did not significantly
affect the velocity and static pressure profiles. The wall static
pressure recovery was found to be more sensitive to changes in the
Reynolds number. By increasing the velocity from 10 m/s to 20 m/s,
the wall static pressure recovery increased by 8.31%. However, as the
divergence angle was increased, a similar increase in the Reynolds
number resulted in a higher percentage increase in pressure recovery.
Experimental results showed that regardless of the wall to which
the flow was attached, both the velocity and pressure fields were
replicated with discrepancies below 2%.
Abstract: Most HWRs currently use natural uranium fuel. Using enriched uranium fuel results in a significant improvement in fuel cycle costs and uranium utilization. On the other hand, reactivity changes of HWRs over the full range of operating conditions from cold shutdown to full power are small. This reduces the required reactivity worth of control devices and minimizes local flux distribution perturbations, minimizing potential problems due to transient local overheating of fuel. Analyzing heavy water effectiveness on neutronic parameters such as enrichment requirements, peaking factor and reactivity is important and should pay attention as primary concepts of a HWR core designing. Two nuclear nuclear reactors of CANDU-type and hexagonal-type reactor cores of 33 fuel assemblies and 19 assemblies in 1.04 P/D have been respectively simulated using MCNP-4C code. Using heavy water and light water as moderator have been compared for achieving less reactivity insertion and enrichment requirements. Two fuel matrixes of (232Th/235U)O2 and (238/235U)O2 have been compared to achieve more economical and safe design. Heavy water not only decreased enrichment needs, but it concluded in negative reactivity insertions during moderator density variations. Thorium oxide fuel assemblies of 2.3% enrichment loaded into the core of heavy water moderator resulted in 0.751 fission to absorption ratio and peaking factor of 1.7 using. Heavy water not only provides negative reactivity insertion during temperature raises which changes moderator density but concluded in 2 to 10 kg reduction of enrichment requirements, depend on geometry type.
Abstract: The success of an electronic system in a System-on- Chip is highly dependent on the efficiency of its interconnection network, which is constructed from routers and channels (the routers move data across the channels between nodes). Since neither classical bus based nor point to point architectures can provide scalable solutions and satisfy the tight power and performance requirements of future applications, the Network-on-Chip (NoC) approach has recently been proposed as a promising solution. Indeed, in contrast to the traditional solutions, the NoC approach can provide large bandwidth with moderate area overhead. The selected topology of the components interconnects plays prime rule in the performance of NoC architecture as well as routing and switching techniques that can be used. In this paper, we present two generic NoC architectures that can be customized to the specific communication needs of an application in order to reduce the area with minimal degradation of the latency of the system. An experimental study is performed to compare these structures with basic NoC topologies represented by 2D mesh, Butterfly-Fat Tree (BFT) and SPIN. It is shown that Cluster mesh (CMesh) and MinRoot schemes achieves significant improvements in network latency and energy consumption with only negligible area overhead and complexity over existing architectures. In fact, in the case of basic NoC topologies, CMesh and MinRoot schemes provides substantial savings in area as well, because they requires fewer routers. The simulation results show that CMesh and MinRoot networks outperforms MESH, BFT and SPIN in main performance metrics.
Abstract: This article discusses the problem of estimating the
orientation of inclined ground on which a human subject stands based
on information provided by the vestibular system consisting of the
otolith and semicircular canals. It is assumed that body segments are
not necessarily aligned and thus forming an open kinematic chain.
The semicircular canals analogues to a technical gyrometer provide a
measure of the angular velocity whereas the otolith analogues to a
technical accelerometer provide a measure of the translational
acceleration. Two solutions are proposed and discussed. The first is
based on a stand-alone Kalman filter that optimally fuses the two
measurements based on their dynamic characteristics and their noise
properties. In this case, no body dynamic model is needed. In the
second solution, a central extended disturbance observer that
incorporates a body dynamic model (internal model) is employed.
The merits of both solutions are discussed and demonstrated by
experimental and simulation results.
Abstract: Internet addiction has become a critical problem on
adolescents in Taiwan, and its negative effects on various dimensions
of adolescent development caught the attention of educational and
psychological experts. This study examined the correlation between
cognitive (locus of control) and emotion (emotion venting strategies)
factors on internet addiction of adolescents in Taiwan. Using the
Compulsive Internet Use (CIU) and the Emotion Venting Strategy
scales, a survey was conducted and 215 effective samples (students
ranging from12 to14 years old) returned. Quantitative analysis
methods such as descriptive statistics, t-test, ANOVA, Pearson
correlations and multiple regression were adopted. The results were as
follows: 1. Severity of Internet addiction has significant gender
differences; boys were at a higher risk than girls in becoming addicted
to the Internet. 2. Emotion venting, locus of control and internet
addiction have been shown to be positive correlated with one another.
3. Setting the locus of control as the control variable, emotion venting
strategy has positive and significant contribution to internet addiction.
The results of this study suggest that coaching deconstructive emotion
strategies and cognitive believes are encouraged to integrate with
actual field work.
Abstract: Constant amplitude fatigue crack growth (FCG) tests
were performed on dissimilar metal welded plates of Type 316L
Stainless Steel (SS) and IS 2062 Grade A Carbon steel (CS). The
plates were welded by TIG welding using SS E309 as electrode. FCG
tests were carried on the Side Edge Notch Tension (SENT)
specimens of 5 mm thickness, with crack initiator (notch) at base
metal region (BM), weld metal region (WM) and heat affected zones
(HAZ). The tests were performed at a test frequency of 10 Hz and at
load ratios (R) of 0.1 & 0.6. FCG rate was found to increase with
stress ratio for weld metals and base metals, where as in case of
HAZ, FCG rates were almost equal at high ΔK. FCG rate of HAZ of
stainless steel was found to be lowest at low and high ΔK. At
intermediate ΔK, WM showed the lowest FCG rate. CS showed
higher crack growth rate at all ΔK. However, the scatter band of data
was found to be narrow. Fracture toughness (Kc) was found to vary
in different locations of weldments. Kc was found lowest for the
weldment and highest for HAZ of stainless steel. A novel method of
characterizing the FCG behavior using an Infrared thermography
(IRT) camera was attempted. By monitoring the temperature rise at
the fast moving crack tip region, the amount of plastic deformation
was estimated.
Abstract: A Simultaneous Multithreading (SMT) Processor is
capable of executing instructions from multiple threads in the same
cycle. SMT in fact was introduced as a powerful architecture to
superscalar to increase the throughput of the processor.
Simultaneous Multithreading is a technique that permits multiple
instructions from multiple independent applications or threads to
compete limited resources each cycle. While the fetch unit has been
identified as one of the major bottlenecks of SMT architecture, several
fetch schemes were proposed by prior works to enhance the fetching
efficiency and overall performance.
In this paper, we propose a novel fetch policy called queue situation
identifier (QSI) which counts some kind of long latency instructions of
each thread each cycle then properly selects which threads to fetch
next cycle. Simulation results show that in best case our fetch policy
can achieve 30% on speedup and also can reduce the data cache level 1
miss rate.
Abstract: Visual information is very important in human perception
of surrounding world. Video is one of the most common ways to
capture visual information. The video capability has many benefits
and can be used in various applications. For the most part, the
video information is used to bring entertainment and help to relax,
moreover, it can improve the quality of life of deaf people. Visual
information is crucial for hearing impaired people, it allows them to
communicate personally, using the sign language; some parts of the
person being spoken to, are more important than others (e.g. hands,
face). Therefore, the information about visually relevant parts of the
image, allows us to design objective metric for this specific case. In
this paper, we present an example of an objective metric based on
human visual attention and detection of salient object in the observed
scene.
Abstract: Innovations and innovative activity get the increasing
value for successful financial and economic activity of the countries
and regions. The level of innovative sphere development determines
place of a country or a region in world economy and forms a basis of
steady economic growth. This article is devoted to different aspects
of organization of the national economic safety in the conditions of
innovative development, its problems, risks and threats. Economy
can be considered as aspiring for transition to innovative way only
with finding of economic safety: financial independence, power
stability and technological progress. There are statistical indicators,
defining the level of economic security and factors, threatening
economic safety of the state. The research is based on the analysis of
factors and indicators in conditions of innovative development. The
paper is illustrated by the examples of possible estimated system of
the economic safety level.
Abstract: The aim of this study was to analyse the most
important parameters determining the quality of the motion structure
of the basic classical dance jump – grand jeté.Research sample
consisted of 8 students of the Dance Conservatory in Brno. Using the
system Simi motion we performed a 3D kinematic analysis of the
jump. On the basis of the comparison of structure quality and
measured data of the grand jeté, we defined the optimal values of the
relevant parameters determining the quality of the performance. The
take-off speed should achieve about 2.4 m·s-1, the optimum take-off
angle is 28 - 30º. The take-off leg should swing backward at the
beginning of the flight phase with the minimum speed of 3.3 m·s-1.If
motor abilities of dancers achieve the level necessary for optimal
performance of a classical dance jump, there is room for certain
variability of the structure of the dance jump.