Abstract: A multi-block algorithm and its implementation in two-dimensional finite element numerical model CCHE2D are presented. In addition to a conventional Lagrangian Interpolation Method (LIM), a novel interpolation method, called Consistent Interpolation Method (CIM), is proposed for more accurate information transfer across the interfaces. The consistent interpolation solves the governing equations over the auxiliary elements constructed around the interpolation nodes using the same numerical scheme used for the internal computational nodes. With the CIM, the momentum conservation can be maintained as well as the mass conservation. An imbalance correction scheme is used to enforce the conservation laws (mass and momentum) across the interfaces. Comparisons of the LIM and the CIM are made using several flow simulation examples. It is shown that the proposed CIM is physically more accurate and produces satisfactory results efficiently.
Abstract: The temperature distribution and the heat transfer
rates through a multi-layer door of a furnace were investigated. The
inside of the door was in contact with hot air and the other side of the
door was in contact with room air. Radiation heat transfer from the
walls of the furnace to the door and the door to the surrounding area
was included in the problem. This work is a two dimensional steady
state problem. The Churchill and Chu correlation was used to find
local convection heat transfer coefficients at the surfaces of the
furnace door. The thermophysical properties of air were the functions
of the temperatures. Polynomial curve fitting for the fluid properties
were carried out. Finite difference method was used to discretize for
conduction heat transfer within the furnace door. The Gauss-Seidel
Iteration was employed to compute the temperature distribution in
the door.
The temperature distribution in the horizontal mid plane of the
furnace door in a two dimensional problem agrees with the one
dimensional problem. The local convection heat transfer coefficients
at the inside and outside surfaces of the furnace door are exhibited.
Abstract: A new decomposition form is introduced in this report
to establish a criterion for the bi-partite separability of Bell diagonal
states. A such criterion takes a quadratic inequality of the coefficients
of a given Bell diagonal states and can be derived via a simple
algorithmic calculation of its invariants. In addition, the criterion can
be extended to a quantum system of higher dimension.
Abstract: Training with Functional Electrical Stimulation (FES)
has both physiological and psychological benefits for spinal cord
injured subjects. Commonly used methods for quantification of
spasticity have shown controversial reliability. In this study we
propose a method for quick determination of spasticity in spinal cord
injured subjects on a cycling and measurement system. 23 patients
did training sessions on an instrumented mobile FES cycle three
times a week over two months as part of their clinical rehabilitation
program. Spasticity (MAS) and the legs resistance to the pedaling
motion were assessed before and after the FES training and
measurements were done on the subjects ability to pedal with our
without motor assistance. Measurements with test persons with
incomplete spastic paraplegia have shown that spasticity is decreased
after a 30 min cycling training with functional electrical stimulation
(FES).
Abstract: Component-Based software engineering provides an
opportunity for better quality and increased productivity in software
development by using reusable software components [10]. One of the
most critical aspects of the quality of a software system is its
performance. The systematic application of software performance
engineering techniques throughout the development process can help
to identify design alternatives that preserve desirable qualities such
as extensibility and reusability while meeting performance objectives
[1]. In the present scenario, software engineering methodologies
strongly focus on the functionality of the system, while applying a
“fix- it-later" approach to software performance aspects [3]. As a
result, lengthy fine-tunings, expensive extra hard ware, or even
redesigns are necessary for the system to meet the performance
requirements. In this paper, we propose design based,
implementation independent, performance prediction approach to
reduce the overhead associated in the later phases while developing a
performance guaranteed software product with the help of Unified
Modeling Language (UML).
Abstract: In this paper, stability and Hopf bifurcation analysis of
a novel hyperchaotic system are investigated. Four feedback control
strategies, the linear feedback control method, enhancing feedback
control method, speed feedback control method and delayed feedback
control method, are used to control the hyperchaotic attractor to
unstable equilibrium. Moreover numerical simulations are given to
verify the theoretical results.
Abstract: Extraction of lactic acid by emulsion liquid membrane technology (ELM) using n-trioctyl amine (TOA) in n-heptane as carrier within the organic membrane along with sodium carbonate as acceptor phase was optimized by using response surface methodology (RSM). A three level Box-Behnken design was employed for experimental design, analysis of the results and to depict the combined effect of five independent variables, vizlactic acid concentration in aqueous phase (cl), sodium carbonate concentration in stripping phase (cs), carrier concentration in membrane phase (ψ), treat ratio, and batch extraction time (τ)
with equal volume of organic and external aqueous phase on lactic acid extraction efficiency. The maximum lactic acid extraction efficiency (ηext) of 98.21%from aqueous phase in a batch reactor using ELM was found at the optimized values for test variables, cl, cs, ψ, and τ as 0.06 [M], 0.18 [M], 4.72 (%,v/v), 1.98 (v/v) and 13.36 min respectively.
Abstract: This paper describes dynamic analysis using proposed
fast finite element method for a shock absorbing structure including a
sponge. The structure is supported by nonlinear concentrated springs.
The restoring force of the spring has cubic nonlinearity and linear
hysteresis damping. To calculate damping properties for the structures
including elastic body and porous body, displacement vectors as
common unknown variable are solved under coupled condition. Under
small amplitude, we apply asymptotic method to complex eigenvalue
problem of this system to obtain modal parameters. And then
expressions of modal loss factor are derived approximately. This
approach was proposed by one of the authors previously. We call this
method as Modal Strain and Kinetic Energy Method (MSKE method).
Further, using the modal loss factors, the discretized equations in
physical coordinate are transformed into the nonlinear ordinary
coupled equations using normal coordinate corresponding to linear
natural modes. This transformation yields computation efficiency. As
a numerical example of a shock absorbing structures, we adopt double
skins with a sponge. The double skins are supported by nonlinear
concentrated springs. We clarify influences of amplitude of the input
force on nonlinear and chaotic responses.
Abstract: The usual method of river flow diversion involves construction of tunnels and cofferdams. Given the fact that the cost of diversion works could be as high as 10-20% of the total dam construction cost, due attention should be paid to optimum design of the diversion works. The cost of diversion works depends, on factors, such as: the tunnel dimensions and the intended tunneling support measures during and after excavation; quality and characterizes of the rock through which the tunnel should be excavated; the dimensions of the upstream (and downstream) cofferdams; and the magnitude of river flood the system is designed to divert. In this paper by use of the cost of unit prices for tunnel excavation, tunnel lining, tunnel support (rock bolt + shotcrete) and cofferdam fill the cost function was determined. The function is then minimized by the aid of PSO Algorithm (particle swarm optimization). It is found that the optimum diameter and the total diversion cost are directly related to the river flood discharge (Q). It has also shown that in addition to optimum diameter design discharge (Q), river length, tunnel length, is mainly a function of the ratios (not the absolute values) of the unit prices and does not depend on the overall price levels in the respective country. The results of optimization use in some of the case study lead us to significant changes in the cost.
Abstract: Study fluid flow and heat transfer characteristics of
microchannel in a primary Cross-corrugated(CC) surface recuperators
with corrugations and without corrugations, using CFD method. The
pitch-over-height ratios P/H of Cross-corrugated (CC) surface is from
1.5 to 4.0, included angles β=75º. The study was performed using CFD
software FLUENT to create unit model and simulate fluid
temperature, velocity, heat transfer coefficient and other parameters.
The results from these simulations were compared to experimental
data. It is concluded that, when the Reynolds number is constant, if
increase P/H, j/f will decrease, also the decreasing trend will become
weak. Under the condition of P/H=2.2, if increase the inlet velocity j/f
will decrease; in addition, the heat transfer performance in surface
with corrugation will increase 10% compared to that without
corrugation. The study results can provide the basis to optimize the
design, select the type of heat transfer surface, the scale structure, and
heat-transfer surface arrangement for recuperators.
Abstract: We construct an exponentially weighted Legendre- Gauss Tau method for solving differential equations with oscillatory solutions. The proposed method is applied to Sturm-Liouville problems. Numerical examples illustrating the efficiency and the high accuracy of our results are presented.
Abstract: The operating control parameters of injection
flushing type of electrical discharge machining process on stainless
steel 304 workpiece using copper tools are being optimized
according to its individual machining characteristic i.e. Electrode
Wear Ratio (EWR). Higher EWR would give bad dimensional
precision for the EDM machined workpiece because of high
electrode wear. Hence, the quality characteristic for EWR is set to
lower-the-better to achieve the optimum dimensional precision for
the machined workpiece. Taguchi method has been used for the
construction, layout and analysis of the experiment for EWR
machining characteristic. The use of Taguchi method in the
experiment saves a lot of time and cost of preparing and machining
the experiment samples. Therefore, an L18 Orthogonal array
which was the fundamental component in the statistical design of
experiments has been used to plan the experiments and Analysis of
Variance (ANOVA) is used to determine the optimum machining
parameters for this machining characteristic. The control
parameters selected for this optimization experiments are polarity,
pulse on duration, discharge current, discharge voltage, machining
depth, machining diameter and dielectric liquid pressure. The
result had shown that negative polarity machining parameter
setting will decreases EWR.
Abstract: In recent times there has been a growing interest in the
development of quasi-two-dimensional niobium pentoxide (Nb2O5)
as a semiconductor for the potential electronic applications such as
capacitors, filtration, dye-sensitised solar cells and gas sensing
platforms. Therefore once the purpose is established, Nb2O5 can be
prepared in a number of nano- and sub-micron-structural
morphologies that include rods, wires, belts and tubes. In this study
films of Nb2O5 were prepared on gold plated silicon substrate using
spin-coating technique and subsequently by mechanical exfoliation.
The reason this method was employed was to achieve layers of less
than 15nm in thickness. The sintering temperature of the specimen
was 800oC. The morphology and structural characteristics of the
films were analyzed by Atomic Force Microscopy (AFM), Raman
Spectroscopy, X-ray Photoelectron Spectroscopy (XPS).
Abstract: The current practice of determination of moisture diffusivity of building materials under laboratory conditions is predominantly aimed at the absorption phase. The main reason is the simplicity of the inverse analysis of measured moisture profiles. However, the liquid moisture transport may exhibit significant hysteresis. Thus, the moisture diffusivity should be different in the absorption (wetting) and desorption (drying) phase. In order to bring computer simulations of hygrothermal performance of building materials closer to the reality, it is then necessary to find new methods for inverse analysis which could be used in the desorption phase as well. In this paper we present genetic algorithm as a possible method of solution of the inverse problem of moisture transport in desorption phase. Its application is demonstrated for AAC as a typical building material.
Abstract: Construction projects can be implemented under various contractual and organizational systems. They can be divided into two groups: systems without the managing company where the Client manages the process, and systems with the managing company, where management is entrusted to an external company. In the public sector of the Polish market there are two ways of delivery of construction projects with the participation of the manager: one is to assign operations to another party, the so called Project Supervisor, whilst the other results from the application of FIDIC conditions of contract, which entail appointment of the Engineer. The decision is to be made by the Client and depends on various factors. On the public procurement market in Poland the selection of construction project manager boils down to awarding the contract for such a service. The selection can be done by one of eight public procurement procedures identified by the procurement law. The paper provides the analysis of 96 contracts for services awarded in 2011, which employed construction management. The study aimed to investigate the methods and criteria for selecting managers, applied in practice by the Polish public Clients.
Abstract: Numerous divergence measures (spectral distance, cepstral
distance, difference of the cepstral coefficients, Kullback-Leibler
divergence, distance given by the General Likelihood Ratio, distance
defined by the Recursive Bayesian Changepoint Detector and the
Mahalanobis measure) are compared in this study. The measures are
used for detection of abrupt spectral changes in synthetic AR signals
via the sliding window algorithm. Two experiments are performed;
the first is focused on detection of single boundary while the second
concentrates on detection of a couple of boundaries. Accuracy of
detection is judged for each method; the measures are compared
according to results of both experiments.
Abstract: A computational study at the level density functional theory (DFT) was carried out to investigate the influences of Si and C-doping on the 14N and 27Al quadrupole coupling constant in the (10, 0) zigzag single ? walled Aluminum-Nitride nanotube (AlNNT). To this aim, a 1.16nm, length of AlNNT consisting of 40 Al atoms and 40 N atoms were selected where the end atoms are capped by hydrogen atom. To follow the purpose, three Si atoms and three C atoms were doped instead of three Al atoms and three N atoms as a central ring in the surface of the Si and C-doped AlNNT. At first both of systems optimized at the level of BLYP method and 6-31G (d) basis set and after that, the NQR parameters were calculated at the level BLYP method and 6-311+G** basis set in two optimized forms. The calculate CQ values for both optimized AlNNT systems, raw and Si and C-doped, reveal different electronic environments in the mentioned systems. It was also demonstrated that the end nuclei have the largest CQ values in both considered AlNNT systems. All the calculations were carried out using Gaussian 98 package of program.
Abstract: This paper propose the robust character segmentation method for license plate with topological transform such as twist,rotation. The first step of the proposed method is to find a candidate region for character and license plate. The character or license plate
must be appeared as closed loop in the edge image. In the case of
detecting candidate for character region, the evaluation of detected
region is using topological relationship between each character. When
this method decides license plate candidate region, character features
in the region with binarization are used. After binarization for the detected candidate region, each character region is decided again. In
this step, each character region is fitted more than previous step. In the
next step, the method checks other character regions with different
scale near the detected character regions, because most license plates
have license numbers with some meaningful characters around them.
The method uses perspective projection for geometrical normalization.
If there is topological distortion in the character region, the method
projects the region on a template which is defined as standard license
plate using perspective projection. In this step, the method is able to
separate each number region and small meaningful characters. The
evaluation results are tested with a number of test images.
Abstract: Successful intelligence (SI) is the integrated set of the
ability needed to attain success in life, within individual-s sociocultural
context. People are successfully intelligent by recognizing
their strengths and weaknesses. They will find ways to strengthen
their weakness and maintain their strength or even improve it. SI
people can shape, select, and adapt to the environments by using
balance of higher-ordered thinking abilities including; critical,
creative, and applicative. Aims: The purposes of this study were to;
1) develop curriculum that promotes SI for nursing students, and 2)
study the effectiveness of the curriculum development. Method:
Research and Development was a method used for this study. The
design was divided into two phases; 1) the curriculum development
which composed of three steps (needs assessment, curriculum
development and curriculum field trail), and 2) the curriculum
implementation. In this phase, a pre-experimental research design
(one group pretest-posttest design) was conducted. The sample
composed of 49 sophomore nursing students of Boromarajonani
College of Nursing, Surin, Thailand who enrolled in Nursing care of
Health problem course I in 2011 academic year. Data were carefully
collected using 4 instruments; 1) Modified essay questions test
(MEQ) 2) Nursing Care Plan evaluation form 3) Group processing
observation form (α = 0.74) and 4) Satisfied evaluation form of
learning (α = 0.82). Data were analyzed using descriptive statistics
and content analysis. Results: The results revealed that the sample
had post-test average score of SI higher than pre-test average score
(mean difference was 5.03, S.D. = 2.84). Fifty seven percentages of
the sample passed the MEQ posttest at the criteria of 60 percentages.
Students demonstrated the strategies of how to develop nursing care
plan. Overall, students- satisfaction on teaching performance was at
high level (mean = 4.35, S.D. = 0.46). Conclusion: This curriculum
can promote the attribute of characteristic of SI person and was
highly required to be continued.
Abstract: Optimal selection of electrical insulations in electrical
machinery insures reliability during operation. From the insulation
studies of view for electrical machines, stator is the most important
part. This fact reveals the requirement for inspection of the electrical
machine insulation along with the electro-thermal stresses. In the
first step of the study, a part of the whole structure of machine in
which covers the general characteristics of the machine is chosen,
then based on the electromagnetic analysis (finite element method),
the machine operation is simulated. In the simulation results, the
temperature distribution of the total structure is presented
simultaneously by using electro-thermal analysis. The results of
electro-thermal analysis can be used for designing an optimal cooling
system. In order to design, review and comparing the cooling
systems, four wiring structures in the slots of Stator are presented.
The structures are compared to each other in terms of electrical,
thermal distribution and remaining life of insulation by using Finite
Element analysis. According to the steps of the study, an optimization
algorithm has been presented for selection of appropriate structure.