Abstract: Transferring patient information between medical care
sites is necessary to deliver better patient care and to reduce medical
cost. So developing of electronic medical records is an important trend
for the world.The Continuity of Care Document (CCD) is product of
collaboration between CDA and CCR standards. In this study, we will
develop a system to generate medical records with entry level based on
CCD template module.
Abstract: In this work, simulation algorithms for contact drying
of agitated particulate materials under vacuum and at atmospheric
pressure were developed. The implementation of algorithms gives a
predictive estimation of drying rate curves and bulk bed temperature
during contact drying. The calculations are based on the penetration
model to describe the drying process, where all process parameters
such as heat and mass transfer coefficients, effective bed properties,
gas and liquid phase properties are estimated with proper
correlations. Simulation results were compared with experimental
data from the literature. In both cases, simulation results were in good
agreement with experimental data. Few deviations were identified
and the limitations of the predictive capabilities of the models are
discussed. The programs give a good insight of the drying behaviour
of the analysed powders.
Abstract: This paper will first describe predictor controllers
when the proportional-integral-derivative (PID) controllers are
inactive for procedures that have large delay time (LDT) in transfer
stage. Therefore in those states, the predictor controllers are better
than the PID controllers, then compares three types of predictor
controllers. The value of these controller-s parameters are obtained
by trial and error method, so here an effort has been made to obtain
these parameters by Ziegler-Nichols method. Eventually in this paper
Ziegler-Nichols method has been described and finally, a PIP
controller has been designed for a thermal system, which circulates
hot air to keep the temperature of a chamber constant.
Abstract: With the advance of information technology in the
new era the applications of Internet to access data resources has
steadily increased and huge amount of data have become accessible
in various forms. Obviously, the network providers and agencies,
look after to prevent electronic attacks that may be harmful or may
be related to terrorist applications. Thus, these have facilitated the
authorities to under take a variety of methods to protect the special
regions from harmful data. One of the most important approaches is
to use firewall in the network facilities. The main objectives of
firewalls are to stop the transfer of suspicious packets in several
ways. However because of its blind packet stopping, high process
power requirements and expensive prices some of the providers are
reluctant to use the firewall. In this paper we proposed a method to
find a discriminate function to distinguish between usual packets and
harmful ones by the statistical processing on the network router logs.
By discriminating these data, an administrator may take an approach
action against the user. This method is very fast and can be used
simply in adjacent with the Internet routers.
Abstract: Stream Control Transmission Protocol (SCTP) has been
proposed to provide reliable transport of real-time communications.
Due to its attractive features, such as multi-streaming and multihoming,
the SCTP is often expected to be an alternative protocol
for TCP and UDP. In the original SCTP standard, the secondary path
is mainly regarded as a redundancy. Recently, most of researches
have focused on extending the SCTP to enable a host to send its
packets to a destination over multiple paths simultaneously. In order
to transfer packets concurrently over the multiple paths, the SCTP
should be well designed to avoid unnecessary fast retransmission
and the mis-estimation of congestion window size through the paths.
Therefore, we propose an Enhanced Cooperative ACK SCTP (ECASCTP)
to improve the path recovery efficiency of multi-homed host
which is under concurrent multiple transfer mode. We evaluated the
performance of our proposed scheme using ns-2 simulation in terms
of cwnd variation, path recovery time, and goodput. Our scheme
provides better performance in lossy and path asymmetric networks.
Abstract: This paper presents a hybrid association control
scheme that can maintain load balancing among access points in the
wireless LANs and can satisfy the quality of service requirements of
the multimedia traffic applications. The proposed model is
mathematically described as a linear programming model. Simulation
study and analysis were conducted in order to demonstrate the
performance of the proposed hybrid load balancing and association
control scheme. Simulation results shows that the proposed scheme
outperforms the other schemes in term of the percentage of blocking
and the quality of the data transfer rate providing to the multimedia
and real-time applications.
Abstract: The reliable results of an insulated oval duct
considering heat radiation are obtained basing on accurate oval
perimeter obtained by integral method as well as one-dimensional
Plane Wedge Thermal Resistance (PWTR) model. This is an extension
study of former paper of insulated oval duct neglecting heat radiation.
It is found that in the practical situations with long-short-axes ratio a/b
4.5% while t/R2
Abstract: For fire safety purposes, the fire resistance and the
structural behavior of reinforced concrete members are assessed to
satisfy specific fire performance criteria. The available prescribed
provisions are based on standard fire load. Under various fire
scenarios, engineers are in need of both heat transfer analysis and
structural analysis. For heat transfer analysis, the study proposed a
modified finite difference method to evaluate the temperature profile
within a cross section. The research conducted is limited to concrete
sections exposed to a fire on their one side. The method is based on
the energy conservation principle and a pre-determined power
function of the temperature profile. The power value of 2.7 is found
to be a suitable value for concrete sections. The temperature profiles
of the proposed method are only slightly deviate from those of the
experiment, the FEM and the FDM for various fire loads such as
ASTM E 119, ASTM 1529, BS EN 1991-1-2 and 550 oC. The
proposed method is useful to avoid incontinence of the large matrix
system of the typical finite difference method to solve the
temperature profile. Furthermore, design engineers can simply apply
the proposed method in regular spreadsheet software.
Abstract: Academia-industry relationship is not like that of
technology donator-acceptor, but is of interactive and collaborative
nature, acknowledging and ensuring mutual respect for each other-s
role and contributions with an eye to attaining the true purpose of
such relationships, namely, bringing about research-outcome
synergy. Indeed, academia-industry interactions are a system that
requires active and collaborative participations of all the
stakeholders.
This paper examines various issues associated with academic
institutions and industry collaboration with special attention to the
nature of resources and potentialities of stakeholders in the context of
knowledge management. This paper also explores the barriers of
academia-industry interaction. It identifies potential areas where
industry-s participation with academia would be most effective for
synergism. Lastly, this paper proposes an integrated model of several
new collaborative approaches that are possible, mainly in the Indian
scenario to strengthen academia-industry interface.
Abstract: Recently, a model multi-agent e-commerce system based on mobile buyer agents and transfer of strategy modules was proposed. In this paper a different approach to code mobility is introduced, where agent mobility is replaced by local agent creation supplemented by similar code mobility as in the original proposal. UML diagrams of agents involved in the new approach to mobility and the augmented system activity diagram are presented and discussed.
Abstract: In this paper, a PSO-based approach is proposed to
derive a digital controller for redesigned digital systems having an interval plant based on resemblance of the extremal gain/phase
margins. By combining the interval plant and a controller as an interval system, extremal GM/PM associated with the loop transfer function
can be obtained. The design problem is then formulated as an optimization problem of an aggregated error function revealing the deviation on the extremal GM/PM between the redesigned digital
system and its continuous counterpart, and subsequently optimized by
a proposed PSO to obtain an optimal set of parameters for the digital controller. Computer simulations have shown that frequency
responses of the redesigned digital system having an interval plant bare a better resemblance to its continuous-time counter part by the incorporation of a PSO-derived digital controller in comparison to those obtained using existing open-loop discretization methods.
Abstract: The flow and heat transfer mechanism in convex
corrugated tubes have been investigated through numerical
simulations in this paper. Two kinds of tube types named as symmetric
corrugated tube (SCT) and asymmetric corrugated tube (ACT) are
modeled and studied numerically based on the RST model. The
predictive capability of RST model is examined in the corrugation wall
in order to check the reliability of RST model under the corrugation
wall condition. We propose a comparison between the RST modelling
the corrugation wall with existing direct numerical simulation of Maaß
C and Schumann U [14]. The numerical results pressure coefficient at
different profiles between RST and DNS are well matched. The
influences of large corrugation tough radii to heat transfer and flow
characteristic had been considered. Flow and heat transfer comparison
between SCT and ACT had been discussed. The numerical results
show that ACT exhibits higher overall heat transfer performance than
SCT.
Abstract: The emergence of information technology has
resulted in an ever-increasing demand to use computers for the
efficient management and dissemination of information. Keeping in
view the strong need of farmers to collect important and updated
information for interactive, flexible and quick decision-making, a
model of Decision Support System for Farm Management is
developed. The paper discusses the use of Internet technology for the
farmers to take decisions. A model is developed for the farmers to
access online interactive and flexible information for their farm
management. The workflow of the model is presented highlighting
the information transfer between different modules.
Abstract: Virtual Assembly (VA) is one of the key technologies
in advanced manufacturing field. It is a promising application of
virtual reality in design and manufacturing field. It has drawn much
interest from industries and research institutes in the last two decades.
This paper describes a process for integrating an interactive Virtual
Reality-based assembly simulation of a digital mockup with the
CAD/CAM infrastructure. The necessary hardware and software
preconditions for the process are explained so that it can easily be
adopted by non VR experts. The article outlines how assembly
simulation can improve the CAD/CAM procedures and structures;
how CAD model preparations have to be carried out and which
virtual environment requirements have to be fulfilled. The issue of
data transfer is also explained in the paper. The other challenges and
requirements like anti-aliasing and collision detection have also been
explained. Finally, a VA simulation has been carried out for a ball
valve assembly and a car door assembly with the help of Vizard
virtual reality toolkit in a semi-immersive environment and their
performance analysis has been done on different workstations to
evaluate the importance of graphical processing unit (GPU) in the
field of VA.
Abstract: Vernonia divergens Benth., commonly known as
“Insulin Plant” (Fam: Asteraceae) is a potent sugar killer. Locally the
leaves of the plant, boiled in water are successfully administered to a
large number of diabetic patients. The present study evaluates the
putative anti-diabetic ingredients, isolated from the in vivo and in
vitro grown plantlets of V. divergens for their antimicrobial and
anticancer activities. Sterilized explants of nodal segments were
cultured on MS (Musashige and Skoog, 1962) medium in presence of
different combinations of hormones. Multiple shoots along with
bunch of roots were regenerated at 1mg l-1 BAP and 0.5 mg l-1 NAA.
Micro-plantlets were separated and sub-cultured on the double
strength (2X) of the above combination of hormones leading to
increased length of roots and shoots. These plantlets were
successfully transferred to soil and survived well in nature. The
ethanol extract of plantlets from both in vivo & in vitro sources were
prepared in soxhlet extractor and then concentrated to dryness under
reduced pressure in rotary evaporator. Thus obtainedconcentrated
extracts showed significant inhibitory activity against gram
negative bacteria like Escherichia coli and Pseudomonas
aeruginosa but no inhibition was found against gram positive
bacteria. Further, these ethanol extracts were screened for in vitro
percentage cytotoxicity at different time periods (24 h, 48 h and 72 h)
of different dilutions. The in vivo plant extract inhibited the growth of
EAC mouse cell lines in the range of 65, 66, 78, and 88% at 100, 50,
25 & 12.5μg mL-1 but at 72 h of treatment. In case of the extract of in
vitro origin, the inhibition was found against EAC cell lines even at
48h. During spectrophotometric scanning, the extracts exhibited
different maxima (ʎ) - four peaks in in vitro extracts as against single
in in vivo preparation suggesting the possible change in the nature of
ingredients during micropropagation through tissue culture
techniques.
Abstract: The paper provides a numerical investigation of the
entropy generation analysis due to natural convection in an inclined
square porous cavity. The coupled equations of mass, momentum,
energy and species conservation are solved using the Control Volume
Finite-Element Method. Effect of medium permeability and
inclination angle on entropy generation is analysed. It was found that
according to the Darcy number and the porous thermal Raleigh
number values, the entropy generation could be mainly due to heat
transfer or to fluid friction irreversibility and that entropy generation
reaches extremum values for specific inclination angles.
Abstract: This paper analyses the unsteady, two-dimensional
stagnation point flow of an incompressible viscous fluid over a flat
sheet when the flow is started impulsively from rest and at the same
time, the sheet is suddenly stretched in its own plane with a velocity
proportional to the distance from the stagnation point. The partial
differential equations governing the laminar boundary layer forced
convection flow are non-dimensionalised using semi-similar
transformations and then solved numerically using an implicit finitedifference
scheme known as the Keller-box method. Results
pertaining to the flow and heat transfer characteristics are computed
for all dimensionless time, uniformly valid in the whole spatial region
without any numerical difficulties. Analytical solutions are also
obtained for both small and large times, respectively representing the
initial unsteady and final steady state flow and heat transfer.
Numerical results indicate that the velocity ratio parameter is found
to have a significant effect on skin friction and heat transfer rate at
the surface. Furthermore, it is exposed that there is a smooth
transition from the initial unsteady state flow (small time solution) to
the final steady state (large time solution).
Abstract: Determination of wellbore problems during a
production/injection process might be evaluated thorough
temperature log analysis. Other applications of this kind of log
analysis may also include evaluation of fluid distribution analysis
along the wellbore and identification of anomalies encountered
during production/injection process. While the accuracy of such
prediction is paramount, the common method of determination of a
wellbore temperature log includes use of steady-state energy balance
equations, which hardly describe the real conditions as observed in
typical oil and gas flowing wells during production operation; and
thus increase level of uncertainties. In this study, a practical method
has been proposed through development of a simplified semianalytical
model to apply for predicting temperature profile along the
wellbore. The developed model includes an overall heat transfer
coefficient accounting all modes of heat transferring mechanism,
which has been focused on the prediction of a temperature profile as
a function of depth for the injection/production wells. The model has
been validated with the results obtained from numerical simulation.
Abstract: This paper proposes a way to track persons by making use of multiple non-overlapping cameras. Tracking persons on multiple non-overlapping cameras enables data communication among cameras through the network connection between a camera and a computer, while at the same time transferring human feature data captured by a camera to another camera that is connected via the network. To track persons with a camera and send the tracking data to another camera, the proposed system uses a hierarchical human model that comprises a head, a torso, and legs. The feature data of the person being modeled are transferred to the server, after which the server sends the feature data of the human model to the cameras connected over the network. This enables a camera that captures a person's movement entering its vision to keep tracking the recognized person with the use of the feature data transferred from the server.