Abstract: In the analysis of structures, the nonlinear effects due to large displacement, large rotation and materially-nonlinear are very important and must be considered for the reliable analysis. The non-linear fmite element analysis has potential as usable and reliable means for analyzing of civil structures with the availability of computer technology. In this research the large displacements and materially nonlinear behavior of shear wall is presented with developing of fmite element code using the standard Galerkin weighted residual formulation. Two-dimensional plane stress model was carried out to present the shear wall response. Total Lagangian formulation, which is computationally more effective, is used in the formulation of stiffness matrices and the Newton-Raphson method is applied for the solution of nonlinear transient equations. The details of the program formulation are highlighted and the results of the analyses are presented, along with a comparison of the response of the structure with Ansys software results. The presented model in this paper can be developed for nonlinear analysis of civil engineering structures with different material behavior and complicated geometry.
Abstract: The main objective of this research was to investigate
the biosorption capacity for biofilms of sulphate reducing bacteria
(SRB) to remove heavy metals, such as Zn, Pb and Cd from
rainwater using laboratory-scale reactors containing mixed support
media. Evidence showed that biosorption had contributed to removal
of heavy metals including Zn, Pb and Cd in presence of SRB and
SRB were also found in the aqueous samples from reactors.
However, the SRB and specific families (Desulfobacteriaceae and
Desulfovibrionaceae) were found mainly in the biomass samples
taken from all reactors at the end of the experiment. EDX-analysis
of reactor solids at end of experiment showed that heavy metals Zn,
Pb and Cd had also accumulated in these precipitates.
Abstract: In spite of the advent of new materials, clay bricks
remain, arguably, the most popular construction materials today.
Nevertheless the low cost and versatility of clay bricks cannot always
be associated with high environmental and sustainable values,
especially in terms of raw material sources and manufacturing
processes. At the same time, the worldwide agricultural footprint is
fast growing, with vast agricultural land cultivation and active
expansion of the agro-based industry. The resulting large quantities of
agricultural wastes, unfortunately, are not always well managed or
utilised. These wastes can be recycled, such as by retrieving fibres
from disposed leaves and fruit bunches, and then incorporated in
brick-making. This way the clay bricks are made a 'greener' building
material and the discarded natural wastes can be reutilised, avoiding
otherwise wasteful landfill and harmful open incineration. This study
examined the physical and mechanical properties of clay bricks made
by adding two natural fibres to a clay-water mixture, with baked and
non-baked conditions. The fibres were sourced from pineapple leaves
(PF) and oil palm fruit bunch (OF), and added within the range of
0.25-0.75 %. Cement was added as a binder to the mixture at 5-15 %.
Although the two fibres had different effects on the bricks produced,
cement appeared to dominate the compressive strength. The
non-baked bricks disintegrated when submerged in water, while the
baked ones displayed cement-dependent characteristics in
water-absorption and density changes. Interestingly, further increase
in fibre content did not cause significant density decrease in both the
baked and non-baked bricks.
Abstract: Sensor network applications are often data centric and
involve collecting data from a set of sensor nodes to be delivered
to various consumers. Typically, nodes in a sensor network are
resource-constrained, and hence the algorithms operating in these
networks must be efficient. There may be several algorithms available
implementing the same service, and efficient considerations may
require a sensor application to choose the best suited algorithm. In
this paper, we present a systematic evaluation of a set of algorithms
implementing the data gathering service. We propose a modular
infrastructure for implementing such algorithms in TOSSIM with
separate configurable modules for various tasks such as interest
propagation, data propagation, aggregation, and path maintenance.
By appropriately configuring these modules, we propose a number
of data gathering algorithms, each of which incorporates a different
set of heuristics for optimizing performance. We have performed
comprehensive experiments to evaluate the effectiveness of these
heuristics, and we present results from our experimentation efforts.
Abstract: In this paper, all variables are supposed to be integer
and positive. In this modern method, objective function is assumed to
be maximized or minimized but constraints are always explained like
less or equal to. In this method, choosing a dual combination of ideal
nonequivalent and omitting one of variables. With continuing this
act, finally, having one nonequivalent with (n-m+1) unknown
quantities in which final nonequivalent, m is counter for constraints,
n is counter for variables of decision.
Abstract: The use of composite materials in offshore engineering for deep sea oil production riser systems has drawn considerable interest due to the potential weight savings and improvement in durability. The design of composite risers consists of two stages: (1) local design based on critical local load cases, and (2) global analysis of the full length composite riser under global loads and assessment of critical locations. In the first stage, eight different material combinations were selected and their laminate configurations optimised under local load considerations. Stage two includes a final local stress analysis of the critical sections of the riser under the combined loads determined in the global analysis. This paper describes two design methodologies of the composite riser to provide minimum structural weight and shows that the use of off angle fibre orientations in addition to axial and hoop reinforcements offer substantial weight savings and ensure the structural capacity.
Abstract: A series of 1-(1H-benzimidazol-2-yl)-3-(substituted phenyl)-2-propen-1-one were allowed to react with hydrazine hydrate and phenyl hydrazine in submitted reactions to get pyrazoline and phenyl pyrazoline derivatives. All the compounds entered for screening at the Tuberculosis Antimicrobial Acquisition and Coordinating Facility (TAACF) for their in vitro antibacterial activity against Mycobacterium tuberculosis H37Rv strain (ATCC 27294) using Microplate Alamar Blue Assay (MABA) susceptibility test. The results expressed as MIC (minimum inhibitory concentration) in μg/mL. Among the fifteen compounds, eight compounds were found to have MIC values less than 10 μg/mL. These were subjected for cytotoxicity assay in VERO cells to determine CC50 (cytotoxic concentration 50%) values and finally SI (Selectivity Index) were calculated. Compound (XV) 2-[5-(4- fluorophenyl)-1-phenyl-4,5-dihydro-1H-3-pyrazolyl]-1Hbenzimidazole was considered the best candidate of the series that could be a good starting point to develop new lead compounds in the fight against tuberculosis.
Abstract: Various sounds generated in the chest are included in
auscultation sound. Adaptive Noise Canceller (ANC) is one of the
useful techniques for biomedical signal. But the ANC is not suitable
for auscultation sound. Because the ANC needs two input channels as
a primary signal and a reference signals, but a stethoscope can
provide just one input sound. Therefore, in this paper, it was
proposed the Single Input ANC (SIANC) for suppression of breath
sound in a cardiac auscultation sound. For the SIANC, it was
proposed that the reference generation system which included Heart
Sound Detector, Control and Reference Generator. By experiment
and comparison, it was confirmed that the proposed SIANC was
efficient for heart sound enhancement and it was independent of
variations of a heartbeat.
Abstract: Enzymatic hydrolysis of starch from natural sources
finds potential application in commercial production of alcoholic
beverage and bioethanol. In this study the effect of starch
concentration, temperature, time and enzyme concentration were
studied and optimized for hydrolysis of cassava (Manihot esculenta)
starch powder (of mesh 80/120) into glucose syrup by immobilized
(using Polyacrylamide gel) a-amylase using central composite
design. The experimental result on enzymatic hydrolysis of cassava
starch was subjected to multiple linear regression analysis using
MINITAB 14 software. Positive linear effect of starch concentration,
enzyme concentration and time was observed on hydrolysis of
cassava starch by a-amylase. The statistical significance of the model
was validated by F-test for analysis of variance (p < 0.01). The
optimum value of starch concentration temperature, time and enzyme
concentration were found to be 4.5% (w/v), 45oC, 150 min, and 1%
(w/v) enzyme. The maximum glucose yield at optimum condition
was 5.17 mg/mL.
Abstract: This paper deals with under actuator dynamic systems such as spring-mass-damper system when the number of control variable is less than the number of state variable. In order to apply optimal control, the controllability must be checked. There are many objective functions to be selected as the goal of the optimal control such as minimum energy, maximum energy and minimum jerk. As the objective function is the first priority, if one like to have the second goal to be applied; however, it could not fit in the objective function format and also avoiding the vector cost for the objective, this paper will illustrate the problem of under actuator dynamic systems with the easiest to deal with comparing between minimum energy and minimum jerk.
Abstract: A universal current-mode biquad is described which
represents an economical variant of well-known KHN (Kerwin,
Huelsman, Newcomb) voltage-mode filter. The circuit consists of
two multiple-output OTAs and of two grounded capacitors. Utilizing
simple splitter of the input current and a pair of jumpers, all the basic
2nd-order transfer functions can be implemented. The principle is
verified by Spice simulation on the level of a CMOS structure of
OTAs.
Abstract: The load frequency control problem of power systems has attracted a lot of attention from engineers and researchers over the years. Increasing and quickly changing load demand, coupled with the inclusion of more generators with high variability (solar and wind power generators) on the network are making power systems more difficult to regulate. Frequency changes are unavoidable but regulatory authorities require that these changes remain within a certain bound. Engineers are required to perform the tricky task of adjusting the control system to maintain the frequency within tolerated bounds. It is well known that to minimize frequency variations, a large proportional feedback gain (speed regulation constant) is desirable. However, this improvement in performance using proportional feedback comes about at the expense of a reduced stability margin and also allows some steady-state error. A conventional PI controller is then included as a secondary control loop to drive the steadystate error to zero. In this paper, we propose a robust controller to replace the conventional PI controller which guarantees performance and stability of the power system over the range of variation of the speed regulation constant. Simulation results are shown to validate the superiority of the proposed approach on a simple single-area power system model.
Abstract: The system is made with main distributed components:
First Level: Industrial Computers placed in Control Room (monitors thermal and electrical processes based on the data provided by the second level); Second Level: PLCs which collects data from process and transmits information on the first level; also takes commands from this level which are further, passed to execution elements from third
level; Third Level: field elements consisting in 3 categories: data collecting elements; data transfer elements from the third level to the second; execution elements which take commands from the second
level PLCs and executes them after which transmits the confirmation of execution to them. The purpose of the automatic functioning is the optimization of the co-generative electrical energy commissioning in the national
energy system and the commissioning of thermal energy to the consumers.
The integrated system treats the functioning of all the equipments and devices as a whole: Gas Turbine Units (GTU); MT 20kV Medium Voltage Station (MVS); 0,4 kV Low Voltage Station (LVS); Main Hot Water Boilers (MHW); Auxiliary Hot Water Boilers (AHW); Gas Compressor Unit (GCU); Thermal Agent Circulation
Pumping Unit (TPU); Water Treating Station (WTS).
Abstract: A study was undertaken to investigate the effect of
liquid nitrogen aeration on mortalities of adult Cryptolestes
furrugineus, rusty grain beetles, in a prototype cardboard grain bin
equipped with an aeration system. The grain bin was filled with Hard
Red Spring wheat and liquid nitrogen was introduced from the bottom
of the bin. The survival of both cold acclimated and unacclimated C.
furrugineus was tested. The study reveals that cold acclimated insects
had higher survival than unacclimated insects under similar cooling
conditions. In most cases, mortalities of as high as 100% were
achieved at the bottom 100 cm of the grain bin for unacclimated
insects for most of the trials. Insect survival increased as the distance
from the bottom of the grain bin increased. There was no adverse
effect of liquid nitrogen aeration on wheat germination.
Abstract: Aiming at the problems existing in low-carbon technology of Chinese manufacturing industries, such as irrational energy structure, lack of technological innovation, financial constraints, this paper puts forward the suggestion that the leading role of the government is combined with the roles of enterprises and market. That is, through increasing the governmental funding the adjustment of the industrial structures and enhancement of the legal supervision are supported. Technological innovation is accelerated by the enterprises, and the carbon trading will be promoted so as to trigger the low-carbon revolution in Chinese manufacturing field.
Abstract: The use of additions in cement in manufacturing,
mortar and concrete offers economic and ecological advantages. Cements with additions such as limestone, slag and natural
pouzzolana are produced in cement factories in Algeria. Several studies analyzed the effect of these additions on the physical and
mechanical properties as well as the durability of concrete. However,
few studies were conducted on the effect of local metakaolin on
mechanical properties and durability of concrete. The main purpose
of this paper is to analyze the performance of mortar and concrete with local metakaolin. The preparation of the metakaolin was carried
out by calcination of kaolin at a temperature of 850 °C for a period of 3 hours. The experimental results have shown that the rates of
substitutions of 10 and 15% metakaolin increases the compressive
strength and flexural strength at both early age and long term. The durability and the permeability were also improved by reducing the
coefficient of sorptivity.
Abstract: CIM is the standard formalism for modeling management
information developed by the Distributed Management Task
Force (DMTF) in the context of its WBEM proposal, designed to
provide a conceptual view of the managed environment. In this
paper, we propose the inclusion of formal knowledge representation
techniques, based on Description Logics (DLs) and the Web Ontology
Language (OWL), in CIM-based conceptual modeling, and then we
examine the benefits of such a decision. The proposal is specified
as a CIM metamodel level mapping to a highly expressive subset
of DLs capable of capturing all the semantics of the models. The
paper shows how the proposed mapping provides CIM diagrams with
precise semantics and can be used for automatic reasoning about the
management information models, as a design aid, by means of newgeneration
CASE tools, thanks to the use of state-of-the-art automatic
reasoning systems that support the proposed logic and use algorithms
that are sound and complete with respect to the semantics. Such a
CASE tool framework has been developed by the authors and its
architecture is also introduced. The proposed formalization is not
only useful at design time, but also at run time through the use of
rational autonomous agents, in response to a need recently recognized
by the DMTF.
Abstract: The development of many measurement and inspection systems of products based on real-time image processing can not be carried out totally in a laboratory due to the size or the temperature of the manufactured products. Those systems must be developed in successive phases. Firstly, the system is installed in the production line with only an operational service to acquire images of the products and other complementary signals. Next, a recording service of the image and signals must be developed and integrated in the system. Only after a large set of images of products is available, the development of the real-time image processing algorithms for measurement or inspection of the products can be accomplished under realistic conditions. Finally, the recording service is turned off or eliminated and the system operates only with the real-time services for the acquisition and processing of the images. This article presents a systematic performance evaluation of the image compression algorithms currently available to implement a real-time recording service. The results allow establishing a trade off between the reduction or compression of the image size and the CPU time required to get that compression level.
Abstract: This work presents the mixed-mode II/III prestressed split-cantilever beam specimen for the fracture testing of composite materials. In accordance with the concept of prestressed composite beams one of the two fracture modes is provided by the prestressed state of the specimen, and the other one is increased up to fracture initiation by using a testing machine. The novel beam-like specimen is able to provide any combination of the mode-II and mode-III energy release rates. A simple closed-form solution is developed using beam theory as a data reduction scheme and for the calculation of the energy release rates in the new configuration. The applicability and the limitations of the novel fracture mechanical test are demonstrated using unidirectional glass/polyester composite specimens. If only crack propagation onset is involved then the mixed-mode beam specimen can be used to obtain the fracture criterion of transparent composite materials in the GII - GIII plane in a relatively simple way.
Abstract: in dissimilar material joints, failure often occurs
along the interface between two materials due to stress singularity.
Stress distribution and its concentration depend on materials and
geometry of the junction. Inhomogenity of stress distribution at the
interface of junction of two materials with different elastic modules
and stress concentration in this zone are the main factors resulting in
rupture of the junction. Effect of joining angle in the interface of
aluminum-polycarbonate will be discussed in this paper. Computer
simulation and finite element analysis by ABAQUS showed that
convex interfacial joint leads to stress reduction at junction corners in
compare with straight joint. This finding is confirmed by photoelastic
experimental results.