Abstract: We report the size dependence of 1D superconductivity in ultrathin (10-130 nm) nanowires produced by coating suspended carbon nanotubes with a superconducting NbN thin film. The resistance-temperature characteristic curves for samples with ≧25 nm wire width show the superconducting transition. On the other hand, for the samples with 10-nm width, the superconducting transition is not exhibited owing to the quantum size effect. The differential resistance vs. current density characteristic curves show some peak, indicating that Josephson junctions are formed in nanowires. The presence of the Josephson junctions is well explained by the measurement of the magnetic field dependence of the critical current. These understanding allow for the further expansion of the potential application of NbN, which is utilized for single photon detectors and so on.
Abstract: The study investigates the causal link between trade
openness and economic growth for four South Asian countries for
period 1972-1985 and 1986-2007 to examine the scenario before and
after the implementation of SAARC. Panel cointegration and
FMOLS techniques are employed for short run and long run
estimates. In 1972-85 short run unidirectional causality from GDP to
openness is found whereas, in 1986-2007 there exists bi-directional
causality between GDP and openness. The long run elasticity
magnitude between GDP and openness contains negative sign in
1972-85 which shows that there exists long run negative relationship.
While in time period 1986-2007 the elasticity magnitude has positive
sign that indicates positive causation between GDP and openness. So
it can be concluded that after the implementation of SAARC overall
situation of selected countries got better. Also long run coefficient of
error term suggests that short term equilibrium adjustments are driven
by adjustment back to long run equilibrium.
Abstract: Minor problems arising from optimizations by
welding of fixed prostheses frameworks can be identified by
macroscopic and microscopic visual inspection. The purpose of this
study was to highlight the visible discontinuities present in the laser
welds of dental Ni-Cr alloys. Ni-Cr base metal alloys designated for
fixed prostheses manufacture were selected for the experiments.
Using cast plates, preliminary tests were conducted by laser welding.
Macroscopic visual inspection was done carefully to assess the
defects of the welding rib. Electron microscopy images allowed
visualization of small discontinuities, which escapes visual
inspection. Making comparison to Ni-Cr alloys taken in the
experiment and laser welded, after visual analysis, the best welds
appear for Heraenium NA alloy.
Abstract: Prior research has examined the relationship between religiosity, religious involvement, and involvement in secular, civic organizations. However, research has not examined the influence of religious involvement on secular, non-civic organizations (i.e. work organizations). This study examines the link between religiosity, religious involvement, and the three-component model of organizational commitment. More specifically, the author hypothesizes that individuals high in religiosity (and religious involvement) will have lower affective, continuance, and normative commitment than less religious (or non-religious) individuals. In addition, it is hypothesized that this relationship is moderated by a third factor: organizational spirituality. Further, the author hypothesizes that for organizations that are spiritual the negative relationship between religiosity and job commitment will be weakened or even negated.
Abstract: Restarted GMRES methods augmented with approximate eigenvectors are widely used for solving large sparse linear systems. Recently a new scheme of augmenting with error approximations is proposed. The main aim of this paper is to develop a restarted GMRES method augmented with the combination of harmonic Ritz vectors and error approximations. We demonstrate that the resulted combination method can gain the advantages of two approaches: (i) effectively deflate the small eigenvalues in magnitude that may hamper the convergence of the method and (ii) partially recover the global optimality lost due to restarting. The effectiveness and efficiency of the new method are demonstrated through various numerical examples.
Abstract: The colors of the human skin represent a special
category of colors, because they are distinctive from the colors of
other natural objects. This category is found as a cluster in color
spaces, and the skin color variations between people are mostly due
to differences in the intensity. Besides, the face detection based on
skin color detection is a faster method as compared to other
techniques. In this work, we present a system to track faces by
carrying out skin color detection in four different color spaces: HSI,
YCbCr, YES and RGB. Once some skin color regions have been
detected for each color space, we label each and get some
characteristics such as size and position. We are supposing that a face
is located in one the detected regions. Next, we compare and employ
a polling strategy between labeled regions to determine the final
region where the face effectively has been detected and located.
Abstract: Double-diffusive natural convection in an open top
square cavity and heated from the side is studied numerically.
Constant temperatures and concentration are imposed along the right
and left walls while the heat balance at the surface is assumed to obey
Newton-s law of cooling. The finite difference method is used to
solve the dimensionless governing equations. The numerical results
are reported for the effect of Marangoni number, Biot number and
Prandtl number on the contours of streamlines, temperature and
concentration. The predicted results for the average Nusselt number
and Sherwood number are presented for various parametric
conditions. The parameters involved are as follows; the thermal
Marangoni number, 0 ≤ MaT ≤1000 , the solutal Marangoni number,
0 1000 c ≤ Ma ≤ , the Biot number, 0 ≤ Bi ≤ 6 , Grashof number,
5 Gr = 10 and aspect ratio 1. The study focused on both flows; thermal
dominated, N = 0.8 , and compositional dominated, N = 1.3 .
Abstract: Prior research has not effectively investigated how the
profitability of Chinese branches affect FDIs in China [1, 2], so this
study for the first time incorporates realistic earnings information
to systematically investigate effects of innovation, imitation, and
profit factors of FDI diffusions from Taiwan to China. Our nonlinear
least square (NLS) model, which incorporates earnings factors,
forms a nonlinear ordinary differential equation (ODE) in numerical
simulation programs. The model parameters are obtained through
a genetic algorithms (GA) technique and then optimized with the
collected data for the best accuracy. Particularly, Taiwanese regulatory
FDI restrictions are also considered in our modified model to meet
the realistic conditions. To validate the model-s effectiveness, this
investigation compares the prediction accuracy of modified model
with the conventional diffusion model, which does not take account
of the profitability factors.
The results clearly demonstrate the internal influence to be positive,
as early FDI adopters- consistent praises of FDI attract potential firms
to make the same move. The former erects a behavior model for the
latter to imitate their foreign investment decision. Particularly, the
results of modified diffusion models show that the earnings from
Chinese branches are positively related to the internal influence. In
general, the imitating tendency of potential consumers is substantially
hindered by the losses in the Chinese branches, and these firms would
invest less into China. The FDI inflow extension depends on earnings
of Chinese branches, and companies will adjust their FDI strategies
based on the returns. Since this research has proved that earning is
an influential factor on FDI dynamics, our revised model explicitly
performs superior in prediction ability than conventional diffusion
model.
Abstract: The aerodynamics characteristics of a blended-wing body (BWB) aircraft were obtained in Universiti Teknologi MARA low speed wind tunnel. The scaled-down of BWB model consisted of a canard as its horizontal stabilizer. There were four canards with different aspect ratio used in the experiments. Canard setting angles were varied from -20q to 20q. All tests were conducted at velocity of 35 m/s, with Mach number 0.1. At low angles of attacks, the increment of lift slope for various canards aspect ratio is small and almost constant. Higher canard aspect ratio will cause higher drag. However, canard has a high effect to the moment at zero lift, CM,0.The visualization using mini tuff was performed to observe the airflow at the upper surface of canard. KeywordsAerodynamics,blended-wing body, canard, wind tunnel.
Abstract: This analysis investigates the distortion of flow
measurement and the increase of cavitation along orifice
flowmeter. The analysis using the numerical method (CFD)
validated the distortion of flow measurement through the inlet
velocity profile considering the convergence and grid
dependency. Realizable k-e model was selected and y+ was
about 50 in this numerical analysis. This analysis also estimated
the vulnerability of cavitation effect due to inlet velocity profile.
The investigation concludes that inclined inlet velocity profile
could vary the pressure which was measured at pressure tab
near pipe wall and it led to distort the pressure values ranged
from -3.8% to 5.3% near the orifice plate and to make the
increase of cavitation. The investigation recommends that the
fully developed inlet velocity flow is beneficial to accurate flow
measurement in orifice flowmeter.
Abstract: Carbon nanotubes (CNTs) possess unique structural,
mechanical, thermal and electronic properties, and have been
proposed to be used for applications in many fields. However, to
reach the full potential of the CNTs, many problems still need to be
solved, including the development of an easy and effective
purification procedure, since synthesized CNTs contain impurities,
such as amorphous carbon, carbon nanoparticles and metal particles.
Different purification methods yield different CNT characteristics
and may be suitable for the production of different types of CNTs. In
this study, the effect of different purification chemicals on carbon
nanotube quality was investigated. CNTs were firstly synthesized by
chemical vapor deposition (CVD) of acetylene (C2H2) on a
magnesium oxide (MgO) powder impregnated with an iron nitrate
(Fe(NO3)3·9H2O) solution. The synthesis parameters were selected
as: the synthesis temperature of 800°C, the iron content in the
precursor of 5% and the synthesis time of 30 min. The liquid phase
oxidation method was applied for the purification of the synthesized
CNT materials. Three different acid chemicals (HNO3, H2SO4, and
HCl) were used in the removal of the metal catalysts from the
synthesized CNT material to investigate the possible effects of each
acid solution to the purification step. Purification experiments were
carried out at two different temperatures (75 and 120 °C), two
different acid concentrations (3 and 6 M) and for three different time
intervals (6, 8 and 15 h). A 30% H2O2 : 3M HCl (1:1 v%) solution
was also used in the purification step to remove both the metal
catalysts and the amorphous carbon. The purifications using this
solution were performed at the temperature of 75°C for 8 hours.
Purification efficiencies at different conditions were evaluated by
thermogravimetric analysis. Thermal and electrical properties of
CNTs were also determined. It was found that the obtained electrical
conductivity values for the carbon nanotubes were typical for organic
semiconductor materials and thermal stabilities were changed
depending on the purification chemicals.
Abstract: The effects of ethylene (C2H4) feed position and
O2/C2H4 feed molar ratio on ethylene epoxidation in a parallel
dielectric barrier discharge (DBD) were studied. The results showed
that the ethylene feed position fraction of 0.5 and the feed molar
ratio of O2/C2H4 of 0.2:1 gave the highest EO selectivity of 34.3%
and the highest EO yield of 5.28% with low power consumptions of
2.11×10-16 Ws/molecule of ethylene converted and 6.34×10-16
Ws/molecule of EO produced when the DBD system was operated
under the best conditions: an applied voltage of 19 kV, an input
frequency of 500 Hz and a total feed flow rate of 50 cm3/min. The
separate ethylene feed system provided much higher epoxidation
activity as compared to the mixed feed system which gave EO
selectivity of 15.5%, EO yield of 2.1% and the power consumption of
EO produced of 7.7×10-16 Ws/molecule.
Abstract: Understanding of how and where NOx formation
occurs in industrial burner is very important for efficient and clean
operation of utility burners. Also the importance of this problem is
mainly due to its relation to the pollutants produced by more burners
used widely of gas turbine in thermal power plants and glass and steel
industry.
In this article, a numerical model of an industrial burner operating
in MILD combustion is validated with experimental data.. Then
influence of air flow rate and air temperature on combustor
temperature profiles and NOX product are investigated. In order to
modification this study reports on the effects of fuel and air dilution
(with inert gases H2O, CO2, N2), and also influence of lean-premixed
of fuel, on the temperature profiles and NOX emission.
Conservation equations of mass, momentum and energy, and
transport equations of species concentrations, turbulence, combustion
and radiation modeling in addition to NO modeling equations were
solved together to present temperature and NO distribution inside the
burner.
The results shows that dilution, cause to a reduction in value of
temperature and NOX emission, and suppresses any flame
propagation inside the furnace and made the flame inside the furnace
invisible. Dilution with H2O rather than N2 and CO2 decreases further
the value of the NOX. Also with raise of lean-premix level, local
temperature of burner and the value of NOX product are decreases
because of premixing prevents local “hot spots" within the combustor
volume that can lead to significant NOx formation. Also leanpremixing
of fuel with air cause to amount of air in reaction zone is
reach more than amount that supplied as is actually needed to burn
the fuel and this act lead to limiting NOx formation
Abstract: Design and evaluation of reciprocating compressors
should include a pulsation study. The object is to ensure that
predicted pulsation levels meet guidelines to limit vibration, shaking
forces, noise, associated pressure drops, horsepower losses and
fabrication cost and time to acceptable levels. This paper explains
procedures and recommendations to select and size pulsation
suppression devices to obtain optimum arrangement in terms of
pulsation, vibration, shaking forces, performance, reliability, safety,
operation, maintenance and commercial conditions. Model and
advanced formulations for pulsation study are presented. The effect
of the full fluid dynamic model on the prediction of pulsation waves
and resulting frequency spectrum distributions are discussed.
Advanced and optimum methods of controlling pulsations are
highlighted. Useful recommendations and guidelines for pulsation
control, piping pulsation analysis, pulsation vessel design, shaking
forces, low pressure drop orifices, pulsation study report and devices
to mitigate pulsation and shaking problems are discussed.
Abstract: Physiological control of a left ventricle assist device (LVAD) is generally a complicated task due to diverse operating environments and patient variability. In this work, a tracking control algorithm based on sliding mode and feed forward control for a class of discrete-time single input single output (SISO) nonlinear uncertain systems is presented. The controller was developed to track the reference trajectory to a set operating point without inducing suction in the ventricle. The controller regulates the estimated mean pulsatile flow Qp and mean pulsatility index of pump rotational speed PIω that was generated from a model of the assist device. We recall the principle of the sliding mode control theory then we combine the feed-forward control design with the sliding mode control technique to follow the reference trajectory. The uncertainty is replaced by its upper and lower boundary. The controller was tested in a computer simulation covering two scenarios (preload and ventricular contractility). The simulation results prove the effectiveness and the robustness of the proposed controller
Abstract: Double-diffusive steady convection in a partially
porous cavity with partially permeable walls and under the combined
buoyancy effects of thermal and mass diffusion was analysed
numerically using finite volume method.
The top wall is well insulated and impermeable while the bottom
surface is partially well insulated and impermeable and partially
submitted to constant temperature T1 and concentration C1. Constant
equal temperature T2 and concentration C2 are imposed along the
vertical surfaces of the enclosure. Mass suction/injection and
injection/suction are respectively considered at the bottom of the
porous centred partition and at one of the vertical walls.
Heat and mass transfer characteristics as streamlines and average
Nusselt numbers and Sherwood numbers were discussed for different
values of buoyancy ratio, Rayleigh number, and injection/suction
coefficient.
It is especially noted that increasing the injection factor
disadvantages the exchanges in the case of the injection while the
transfer is augmented in case of suction. On the other hand, a critical
value of the buoyancy ratio was highlighted for which heat and mass
transfers are minimized.
Abstract: The main objective of seismic rehabilitation in the
foundations is decreasing the range of horizontal and vertical
vibrations and omitting high frequencies contents under the seismic
loading. In this regard, the advantages of micropiles network is
utilized. Reduction in vibration range of foundation can be achieved
by using high dynamic rigidness module such as deep foundations. In
addition, natural frequency of pile and soil system increases in regard
to rising of system rigidness. Accordingly, the main strategy is
decreasing of horizontal and vertical seismic vibrations of the
structure. In this case, considering the impact of foundation, pile and
improved soil foundation is a primary concern. Therefore, in this
paper, effective factors are studied on the seismic rehabilitation of
foundations applying network micropiles in sandy soils with
nonlinear reaction.
Abstract: This paper examines the relationship between financial
risks and profitability of the conventional and Islamic banks in
Malaysia for the period between 1996 and 2005. The measures of
profitability that have been used in the study are the return on equity
(ROE) and return on assets (ROA) while the financial risks are credit
risk, interest rate risk and liquidity risks. This study employs panel
data regression analysis of Generalised Least Squares of fixed effects
and random effects models. It was found that credit risk has a
significant impact on ROA and ROE for the conventional as well as
the Islamic banks. The relationship between interest rate risk and ROE
were found to be weakly significant for the conventional banks and
insignificant for the Islamic banks. The effect of interest rate risk on
ROA is significant for the conventional banks. Liquidity risk was
found to have an insignificant impact on both profitability measures.
Abstract: The numerical simulation of the slip effect via
vicoelastic fluid for 4:1 contraction problem is investigated with
regard to kinematic behaviors of streamlines and stress tensor by
models of the Navier-Stokes and Oldroyd-B equations. Twodimensional
spatial reference system of incompressible creeping flow
with and without slip velocity is determined and the finite element
method of a semi-implicit Taylor-Galerkin pressure-correction is
applied to compute the problem of this Cartesian coordinate system
including the schemes of velocity gradient recovery method and the
streamline-Upwind / Petrov-Galerkin procedure. The slip effect at
channel wall is added to calculate after each time step in order to
intend the alteration of flow path. The result of stress values and the
vortices are reduced by the optimum slip coefficient of 0.1 with near
the outcome of analytical solution.
Abstract: A laboratory set-up was designed to survey the
effectiveness of UV/O3 advanced oxidation process (AOP) for the
removal of Carbaryl from polluted water in batch reactor. The study
was carried out by UV/O3 process for water samples containing 1 to
20 mg/L of Carbaryl in distilled water. Also the range of drinking
water resources adjusted in synthetic water and effects of contact
time, pH and Carbaryl concentration were studied. The residual
pesticide concentration was determined by applying high
performance liquid chromatography (HPLC). The results indicated
that increasing of retention time and pH, enhances pesticide removal
efficiency. The removal efficiency has been affected by pesticide
initial concentration. Samples with low pesticide concentration
showed a remarkable removal efficiency compared to the samples
with high pesticide concentration. AOP method showed the removal
efficiencies of 80% to 100%. Although process showed high
performance for removal of pesticide from water samples, this
process has different disadvantages including complication,
intolerability, difficulty of maintenance and equipmental and
structural requirements.