Abstract: This research aimed to develop plasma system used in air conditioners. This developed plasma system could be installed in the air conditioners - all split type. The quality of air could be improved to be equal to present plasma system. Development processes were as follows: 1) to study the plasma system used in the air conditioners, 2) to design a plasma generator, 3) to develop the plasma generator, and 4) to test its performance in many types of the air conditioners. This plasma system was developed by AC high voltage – 14 kv with a frequency of 50 kHz. Carbon was a conductor to generate arc in air purifier system. The research was tested by installing the plasma generator in the air conditioners - wall type. Whereas, there were 3 types of installations: air flow out, air flow in, and room center. The result of the plasma generator installed in the air conditioners, split type, revealed that the air flow out installation provided the highest average of o-zone at 223 mg/h. This type of installation provided the highest efficiency of air quality improvement. Moreover, the air flow in installation and the room center installation provided the average of the o-zone at 163 mg/h and 64 mg/h, respectively.
Abstract: This paper provides a replacement policy for warranty products with different failure rate from the consumer-s viewpoint. Assume that the product is replaced once within a finite planning horizon, and the failure rate of the second product is lower than the failure rate of the first product. Within warranty period (WP), the failed product is corrected by minimal repair without any cost to the consumers. After WP, the failed product is repaired with a fixed repair cost to the consumers. However, each failure incurs a fixed downtime cost to the consumers over a finite planning horizon. In this paper, we derive the model of the expected total disbursement cost within a finite planning horizon and some properties of the optimal replacement policy under some reasonable conditions are obtained. Finally, numerical examples are given to illustrate the features of the optimal replacement policy under various maintenance costs.
Abstract: Among many agro- based cottage industries in India
sericulture has been promoted as an agro-based, labor intensive, rural
oriented cottage industry, providing gainful employment mainly to
the weaker and marginalized section of the society specially tribal.
Sericulture occupies the place of pride in the rural economy can be
practiced even with very low land holding, low gestation, high
returns make sericulture an ideal program, requiring little capital
investment. In 2010-2011 the employment in sericulture sector was
72.5 lakh persons. The involvement of landless rural people in tasar
sericulture is because they understood its potential for rural and tribal
upliftment. This article demonstrates that certain developmental
initiatives have been playing an important role in the socio-economic
progress of tribal masses in Raigarh district and explains the
increased returns from sericulture as a result of development
programs. The study concludes with some suggestions to improve the
long term feasibility of sericulture.
Abstract: Accurate evaluation of damping ratios involving soilstructure interaction (SSI) effects is the prerequisite for seismic design of in-situ buildings. This study proposes a combined approach to identify damping ratios of SSI systems based on ambient excitation technique. The proposed approach is illustrated with main test process, sampling principle and algorithm steps through an engineering example, as along with its feasibility and validity. The proposed approach is employed for damping ratio identification of 82 buildings in Xi-an, China. Based on the experimental data, the variation range and tendency of damping ratios of these SSI systems, along with the preliminary influence factor, are shown and discussed. In addition, a fitting curve indicates the relation between the damping ratio and fundamental natural period of SSI system.
Abstract: Cultural stories are political. They register cultural
phenomena and their relations with the world and society in term of
their existence, function, characteristics by using different context.
This paper will provide a new way of rethinking which will help us
to rethink the relationship between fiction and politics. It discusses
the theme of human rights and it shows the relevance between art and
politics by studying the civil society through a literary framework.
Reasons to establish a relationship between fiction and politics are
the relevant themes and universal issues among the two disciplines.
Both disciplines are sets of views and ideas formulated by the human
mind to explain political or cultural phenomenon. Other reasons are
the complexity and depth of the author-s vision, and the need to
explain the violations of human rights in a more active structure
which can relate to emotional and social existence.
Abstract: The purpose of this study was to explore the
demographic differences of international tourists according to three
main factors, including the value of time, shopping behavior and
shopping motivation. The Chatuchak Weekend Market is known as
one of the biggest weekend markets in the world. Too little academic
studies had been conducted in this area of weekend market, despite its
growth and continuous development. In general, both domestic
visitors and international tourists are attracted to the perception of
cheap and bargaining prices the weekend market. However, systematic
research study can provide reliable understanding of the perception of
the visitors.
This study focused on the group of international tourists who visited
the market and aimed to provide better insights based on the
differences in their demographic factors. Findings indicated that
several differences in value of time, shopping behavior, and shopping
motivation were identified by gender, income and age. Research
implications and directions for further studies were discussed.
Abstract: An experiment was conducted under controlled
conditions to study the effect of water extract of leaves, shoots and
roots of either Sisymbrium irio L. =SISIR and/or Descurainia
sophia (L.) Schur =DESSO on the germination and primary growth
of wheat. A split-split plot experiment in CRD with three
replications was used. The main plots were the type of weed: i.e.
SISIR and DESSO and the sub-plots were type of organ: i.e. leaf,
stem and root and, the sub-sub plots were concentration of the
water extract of each organ of the weeds: i.e. 0, 2, 4 and 8 % w/v.
The plant materials were cut in 2-3 cm pieces and then were
ground in a blender. The crushed materials were weighed
according to experimental protocol and the final volume was
reached to 100 ml in distilled water in dark bottles. All bottles were
put on a shaker for 24 hours. The solutions were filtered by muslin
cloth. Whatman paper, 9 cm in diameter, were put in petri dishes
and twenty seeds of wheat were put on it and 5 ml distilled water
or water extract of weeds were added to each petri dish. All petri
dishes were put in constant temperature of 15 0C incubator.
The results showed that the SISIR water extract had a greater
inhibitory effects on germination and primary growth of wheat
than those of DESSO water extract. The water extracts of the
leaves of both weeds had the greatest inhibitory effects on
germination and primary growth of wheat, compared to those of
stems and roots. Increasing the concentration of water extract of
leaves, stems and roots of both weeds up to 8 % caused the greatest
inhibitory effects to wheat and reduced the germination rate and
primary growth of it linearly.
Abstract: A study concerning the photocatalytic decolourization
of Congo red (CR) dye, over artificial UV irradiation is presented.
Photocatalysts based on a commercial titanium dioxide (TiO2)
modified with transition metals (Ni, Cu and Zn) were used. The
dopage method used was wet impregnation. A TiO2 sample without
salt was subjected to the same hydrothermal treatment to be used as
reference. Congo red solutions to several pH conditions (natural and
basic) were used to evaluate photocatalytic performance of each
doped catalysts. Photodecolourization percentage was measured
spectrofotrometically after 3 h of treatment to 499 nm as response
variable. Kinetics investigations of photodegradation indicated that
reactions obey to Langmuir-Hinshelwood model and pseudo–first
order law. The rate constant studies of photocatalytic decolourization
reactions for Zn–TiO2 and Cu–TiO2 photocatalysts indicated that in
all cases the rate constant of the reaction was higher than that of TiO2
undoped. These results show that nature of the metal modifying the
TiO2 influence on the efficiency of the photocatalyst evaluated in
process. Ni does not present an additional effect compared with TiO2,
while Zn enhances the photoactivity due to its electronic properties.
Abstract: The paper presents a set of guidelines for analysis of industrial embedded distributed systems and introduces a mathematical model derived from these guidelines. In this study, the author examines a set of modern communication technologies that are or possibly can be used to build communication links between the subsystems of a distributed embedded system. An investigation of these guidelines results in a algorithm for analysis of specific use cases of target technologies. A goal of the paper acts as an important base for ongoing research on comparison of communication technologies. The author describes the principles of the model and presents results of the test calculations. Practical implementation of target technologies and empirical experiment data are based on a practical experience during the design and test of specific distributed systems in Latvian market.
Abstract: Object-oriented simulation is considered one of the most sophisticated techniques that has been widely used in planning, designing, executing and maintaining construction projects. This technique enables the modeler to focus on objects which is extremely important for thorough understanding of a system. Thus, identifying an object is an essential point of building a successful simulation model. In a maintenance process an object is a maintenance work order (MWO). This study demonstrates a maintenance simulation model for the building maintenance division of Saudi Consolidated Electric Company (SCECO) in Dammam, Saudi Arabia. The model focused on both types of maintenance processes namely: (1) preventive maintenance (PM) and (2) corrective maintenance (CM). It is apparent from the findings that object-oriented simulation is a good diagnostic and experimental tool. This is because problems, limitations, bottlenecks and so forth are easily identified. These features are very difficult to obtain when using other tools.
Abstract: The aim of this paper is to introduce and study a new concept of strong double χ2 (M,A, Δ) of fuzzy numbers and also some properties of the resulting sequence spaces of fuzzy numbers were examined.
Abstract: In this study, cometabolic biodegradation of
chloroform was experimented with mixed cultures in the presence of
various organic solvents like methanol, ethanol, isopropanol, acetone,
acetonitrile and toluene as these are predominant discharges in
pharmaceutical industries. Toluene and acetone showed higher
specific chloroform degradation rate when compared to other
compounds. Cometabolic degradation of chloroform was further
confirmed by observation of free chloride ions in the medium. An
extended Haldane model, incorporating the inhibition due to
chloroform and the competitive inhibition between primary
substrates, was developed to predict the biodegradation of primary
substrates, cometabolic degradation of chloroform and the biomass
growth. The proposed model is based on the use of biokinetic
parameters obtained from single substrate degradation studies. The
model was able to satisfactorily predict the experimental results of
ternary and quaternary mixtures. The proposed model can be used for
predicting the performance of bioreactors treating discharges from
pharmaceutical industries.
Abstract: The work presented in this study is related to an
energy system analysis based on passive cooling system for
dwellings. It consists to solar chimney energy performances
determination versus geometrical and environmental considerations
as the size and inlet width conditions of the chimney. Adrar site
located in the southern region of Algeria is chosen for this study
according to ambient temperature and solar irradiance technical data
availability. Obtained results are related to the glazing temperature
distributions, the chimney air flow and internal wall temperatures.
The air room change per hour (ACH) parameter, the outlet air
velocity and mass air flow rate are also determined. It is shown that
the chimney width has a significant effect on energy performances
compared to its entry size. A good agreement is observed between
these results and those obtained by others from the literature.
Abstract: With continuous rise of oil price, how to develop alternative energy source has become a hot topic around the world. This study discussed the dynamic characteristics of an island power system operating under random wind speed lower than nominal wind
speeds of wind turbines. The system primarily consists of three diesel engine power generation systems, three constant-speed variable-pitch wind turbines, a small hydraulic induction generation system, and lumped static loads. Detailed models based on Matlab/Simulink were developed to cater for the dynamic behavior of the system. The results suggested this island power system can operate stably in this operational mode. This study can serve as an important reference for planning, operation, and further expansion of island power systems.
Abstract: The Canadian aerospace industry faces many
challenges. One of them is the difficulty in estimating costs. In
particular, the design effort required in a project impacts resource
requirements and lead-time, and consequently the final cost. This
paper presents the findings of a case study conducted for recognized
global leader in the design and manufacturing of aircraft engines. The
study models parametric cost estimation relationships to estimate the
design effort of integrated blade-rotor low-pressure compressor fans.
Several effort drivers are selected to model the relationship.
Comparative analyses of three types of models are conducted. The
model with the best accuracy and significance in design estimation is
retained.
Abstract: The focal spot of a high intensity focused ultrasound
transducer is small. To heat a large target volume, multiple treatment spots are required. If the power of each treatment spot is fixed, it could
results in insufficient heating of initial spots and over-heating of later ones, which is caused by the thermal diffusion. Hence, to produce a
uniform heated volume, the delivered energy of each treatment spot
should be properly adjusted. In this study, we proposed an iterative, extrapolation technique to adjust the required ultrasound energy of
each treatment spot. Three different scanning pathways were used to evaluate the performance of this technique. Results indicate that by using the proposed technique, uniform heating volume could be obtained.
Abstract: Impaired fertility may be the result of indirect
consumption of anti-fertility agents through food. Monosodium
glutamate (MSG) has been widely used as food additive, flavour
enhancer and included in vaccines. This study focuses in determining
the gonadotoxic and cytotoxic effect of MSG on selected sperm
parameters such as sperm viability, sperm membrane integrity and
testes cytoarchitecture of male mice via histological examination to
determine its effect on spermatogenesis. Twenty-four Mus musculus
were randomly divided into 4 groups and given intraperitoneal
injections (IP) daily for 14 days of different MSG concentrations at
250, 500 and 1000mg/kg MSG to body weight to induce obesity.
Saline was given to control group. Mice were sacrificed and analysis
revealed abnormalities in values for sperm parameters and damages
to testes cytoarchitecture of male mice. The results recorded
decreased viability (p0.05) with degenerative structures in seminiferous tubule of
testes. The results indicated various implications of MSG on male
mice reproductive system which has consequences in fertility
potential.
Abstract: The area of Project Risk Management (PRM) has
been extensively researched, and the utilization of various tools and
techniques for managing risk in several industries has been
sufficiently reported. Formal and systematic PRM practices have
been made available for the construction industry. Based on such
body of knowledge, this paper tries to find out the global picture of
PRM practices and approaches with the help of a survey to look into
the usage of PRM techniques and diffusion of software tools, their
level of maturity, and their usefulness in the construction sector.
Results show that, despite existing techniques and tools, their usage is
limited: software tools are used only by a minority of respondents
and their cost is one of the largest hurdles in adoption. Finally, the
paper provides some important guidelines for future research
regarding quantitative risk analysis techniques and suggestions for
PRM software tools development and improvement.
Abstract: Traditionally, wind tunnel models are made of metal
and are very expensive. In these years, everyone is looking for ways
to do more with less. Under the right test conditions, a rapid
prototype part could be tested in a wind tunnel. Using rapid prototype
manufacturing techniques and materials in this way significantly
reduces time and cost of production of wind tunnel models. This
study was done of fused deposition modeling (FDM) and their ability
to make components for wind tunnel models in a timely and cost
effective manner. This paper discusses the application of wind tunnel
model configuration constructed using FDM for transonic wind
tunnel testing. A study was undertaken comparing a rapid
prototyping model constructed of FDM Technologies using
polycarbonate to that of a standard machined steel model. Testing
covered the Mach range of Mach 0.3 to Mach 0.75 at an angle-ofattack
range of - 2° to +12°. Results from this study show relatively
good agreement between the two models and rapid prototyping
Method reduces time and cost of production of wind tunnel models.
It can be concluded from this study that wind tunnel models
constructed using rapid prototyping method and materials can be
used in wind tunnel testing for initial baseline aerodynamic database
development.
Abstract: This paper describes the results of an extensive study
and comparison of popular hash functions SHA-1, SHA-256,
RIPEMD-160 and RIPEMD-320 with JERIM-320, a 320-bit hash
function. The compression functions of hash functions like SHA-1
and SHA-256 are designed using serial successive iteration whereas
those like RIPEMD-160 and RIPEMD-320 are designed using two
parallel lines of message processing. JERIM-320 uses four parallel
lines of message processing resulting in higher level of security than
other hash functions at comparable speed and memory requirement.
The performance evaluation of these methods has been done by using
practical implementation and also by using step computation
methods. JERIM-320 proves to be secure and ensures the integrity of
messages at a higher degree. The focus of this work is to establish
JERIM-320 as an alternative of the present day hash functions for the
fast growing internet applications.