Abstract: The present study was undertaken to investigate the
effect of pre-aging and aging parameters (time and temperature) on
the mechanical properties of Al-Mg-Zn (7075) alloys. Ultimate
tensile strength, 0.5% offset yield strength and % elongation
measurements were carried out on specimens prepared from cast and
heat treated 7075 alloys. Aging treatments were carried out for the as
solution treated (SHT) specimens (after quenching in warm water).
The specimens were aged at different conditions; Natural aging was
carried out at room temperature for different periods of time. Double
aging was performed for SHT conditions (pre-aged at different time
and temperature followed by high temperature aging). Ultimate
tensile strength, yield strength and % elongation as a function of
different pre-aging and aging parameters are analyzed to acquire an
understanding of the effects of these variables and their interactions
on the mechanical properties of Be-treated 7075 alloys.
Abstract: It has experimentally been proved that the
performance of compression ignition (C.I.) engine is spray
characteristics related. In modern diesel engine the spray formation
and the eventual combustion process are the vital processes that offer
more challenges towards enhancing the engine performance. In the
present work the numerical simulation has been carried out for
evaporating diesel sprays using Fluent software. For computational
fluid dynamics simulation “Meshing” is done using Gambit software
before transmitting it into Fluent. The simulation is carried out using
hot bomb conditions under varying chamber conditions such as gas
pressure, nozzle diameter and fuel injection pressure. For comparison
purpose, the numerical simulations the chamber conditions were kept
the same as that of the experimental data. At varying chamber
conditions the spray penetration rates are compared with the existing
experimental results.
Abstract: Conventional educational practices, do not offer all
the required skills for teachers to successfully survive in today’s
workplace. Due to poor professional training, a big gap exists across
the curriculum plan and the teacher practices in the classroom. As
such, raising the quality of teaching through ICT-enabled training and
professional development of teachers should be an urgent priority.
‘Mobile Learning’, in that vein, is an increasingly growing field of
educational research and practice across schools and work places. In
this paper, we propose a novel Mobile learning system that allows the
users to learn through an intelligent mobile learning in cooperatively
every-time and every-where. The system will reduce the training cost
and increase consistency, efficiency, and data reliability. To establish
that our system will display neither functional nor performance
failure, the evaluation strategy is based on formal observation of
users interacting with system followed by questionnaires and
structured interviews.
Abstract: Solenoid operated electromagnetic control valve
(ECV) playing an important role for car’s air conditioning control
system. ECV is used in external variable displacement swash plate
type compressor and controls the entire air conditioning system by
means of a pulse width modulation (PWM) input signal supplying
from an external source (controller). Complete form of ECV contains
number of internal features like valve body, core, valve guide,
plunger, guide pin, plunger spring, bellows etc. While designing the
ECV; dimensions of different internal items must meet the standard
requirements as it is quite challenging. In this research paper,
especially the dimensioning of ECV body and its three pressure ports
through which the air/refrigerant passes are considered. Here internal
leakage test analysis of ECV body is being carried out from its
discharge port (Pd) to crankcase port (Pc) when the guide valve is
placed inside it. The experiments have made both in ordinary and
digital system using different assumptions and thereafter compare the
results.
Abstract: Digital image correlation (DIC) is a contactless fullfield
displacement and strain reconstruction technique commonly
used in the field of experimental mechanics. Comparing with
physical measuring devices, such as strain gauges, which only
provide very restricted coverage and are expensive to deploy widely,
the DIC technique provides the result with full-field coverage and
relative high accuracy using an inexpensive and simple experimental
setup. It is very important to study the natural patterns effect on the
DIC technique because the preparation of the artificial patterns is
time consuming and hectic process. The objective of this research is
to study the effect of using images having natural pattern on the
performance of DIC. A systematical simulation method is used to
build simulated deformed images used in DIC. A parameter (subset
size) used in DIC can have an effect on the processing and accuracy
of DIC and even cause DIC to failure. Regarding to the picture
parameters (correlation coefficient), the higher similarity of two
subset can lead the DIC process to fail and make the result more
inaccurate. The pictures with good and bad quality for DIC methods
have been presented and more importantly, it is a systematic way to
evaluate the quality of the picture with natural patterns before they
install the measurement devices.
Abstract: Some regularities of formation of a new structural
state of the thermoplastic polymers - gradually oriented (stretched)
state (GOS) are discussed. Transition into GOS is realized by the
graded oriented stretching - by action of inhomogeneous mechanical
field on the isotropic linear polymers or by zone stretching that is
implemented on a standard tensile-testing machine with using a
specially designed zone stretching device (ZSD). Both technical
approaches (especially zone stretching method) allows to manage the
such quantitative parameters of gradually oriented polymers as a
range of change in relative elongation/orientation degree, length of
this change and profile (linear, hyperbolic, parabolic, logarithmic,
etc.). The possibility of obtaining functionally graded materials
(FGMs) by graded orientation method is briefly discussed. Uniaxial
graded stretching method should be considered as an effective
technological solution to create polymer materials with a
predetermined gradient of physical properties.
Abstract: In and around Erode District, it is estimated that more
than 1250 chemical and allied textile processing fabric industries are
affected, partially closed and shut off for various reasons such as poor
management, poor supplier performance, lack of planning for
productivity, fluctuation of output, poor investment, waste analysis,
labor problems, capital/labor ratio, accumulation of stocks, poor
maintenance of resources, deficiencies in the quality of fabric, low
capacity utilization, age of plant and equipment, high investment and
input but low throughput, poor research and development, lack of
energy, workers’ fear of loss of jobs, work force mix and work ethic.
The main objective of this work is to analyze the existing conditions
in textile fabric sector, validate the break even of Total Productivity
(TP), analyze, design and implement fuzzy sets and mathematical
programming for improvement of productivity and quality
dimensions in the fabric processing industry. It needs to be
compatible with the reality of textile and fabric processing industries.
The highly risk events from productivity and quality dimension were
found by fuzzy systems and results are wrapped up among the textile
fabric processing industry.
Abstract: Leukaemia is a blood cancer disease that contributes
to the increment of mortality rate in Malaysia each year. There are
two main categories for leukaemia, which are acute and chronic
leukaemia. The production and development of acute leukaemia cells
occurs rapidly and uncontrollable. Therefore, if the identification of
acute leukaemia cells could be done fast and effectively, proper
treatment and medicine could be delivered. Due to the requirement of
prompt and accurate diagnosis of leukaemia, the current study has
proposed unsupervised pixel segmentation based on clustering
algorithm in order to obtain a fully segmented abnormal white blood
cell (blast) in acute leukaemia image. In order to obtain the
segmented blast, the current study proposed three clustering
algorithms which are k-means, fuzzy c-means and moving k-means
algorithms have been applied on the saturation component image.
Then, median filter and seeded region growing area extraction
algorithms have been applied, to smooth the region of segmented
blast and to remove the large unwanted regions from the image,
respectively. Comparisons among the three clustering algorithms are
made in order to measure the performance of each clustering
algorithm on segmenting the blast area. Based on the good sensitivity
value that has been obtained, the results indicate that moving kmeans
clustering algorithm has successfully produced the fully
segmented blast region in acute leukaemia image. Hence, indicating
that the resultant images could be helpful to haematologists for
further analysis of acute leukaemia.
Abstract: As the current status and growth of Indian automobile
industry is remarkable, transportation sectors are the main concern in
terms of energy security and climate change. Due to rising demand of
fuel and its dependency on foreign countries that affects the GDP of
nation, suggests that penetration of electrical vehicle will increase in
near future. So in this context analysis is done if the 10 percent of
conventional vehicles including cars, three wheelers and two
wheelers becomes electrical vehicles in near future which is also a
part of Nations Electric Mobility Mission Plan then the saving which
improves the nation’s economy is analyzed in detail. Whether the
Indian electricity grid is capable of taking this load with current
generation and demand all over the country is also analyzed in detail.
Current situation of Indian grid is analyzed and how the gap between
generation and demand can be reduced is discussed in terms of
increasing generation capacity and energy conservation measures.
Electrical energy conservation measures in Industry and especially in
rural areas have been analyzed to improve performance of Indian
electricity grid in context of electrical vehicle penetration in near
future. Author was a part of Vishvakarma yojna in which energy
losses were measured in 255 villages of Gujarat and solutions were
suggested to mitigate them and corresponding reports was submitted
to the authorities of Gujarat government.
Abstract: In order to better understand the long term
implications of the grout wear failure mode in large-diameter plainsided
grouted connections, a numerical model has been developed
and calibrated that can take advantage of existing operational plant
data to predict the wear accumulation for the actual load conditions
experienced over a given period, thus limiting the requirement for
expensive monitoring systems. This model has been derived and
calibrated based on site structural condition monitoring (SCM) data
and supervisory control and data acquisition systems (SCADA) data
for two operational wind turbine generator substructures afflicted
with this challenge, along with experimentally derived wear rates.
Abstract: Vertical Handover(VHO) among different
communication technologies ensuring uninterruption and service
continuity is one of the most important performance parameter in
Heterogenous networks environment. In an integrated Universal
Mobile Telecommunicatin System(UMTS) and Wireless Local
Area Network(WLAN), WLAN is given an inherent priority over
UMTS because of its high data rates with low cost. Therefore
mobile users want to be associated with WLAN maximum of the
time while roaming, to enjoy best possible services with low cost.
That encourages reduction of number of VHO. In this work the
reduction of number of VHO with respect to varying number of
WLAN Access Points(APs) in an integrated UMTS and WLAN
network is investigated through simulation to provide best possible
cost effective service to the users. The simulation has been carried
out for an area (7800 × 9006)m2 where COST-231 Hata model
and 3GPP (TR 101 112 V 3.1.0) specified models are used for
WLAN and UMTS path loss models respectively. The handover
decision is triggered based on the received signal level as compared
to the fade margin. Fade margin gives a probabilistic measure of
the reliability of the communication link. A relationship between
number of WLAN APs and the number of VHO is also established
in this work.
Abstract: Karst term is the determiner of a variety of areas or
landforms and unique perspectives that have been formed in result of
the of the ingredients dissolution of rocks constituter by natural
waters. Shiraz area with an area of 5322km2 is located in the simple
folded belt in the southern part of Zagros Mountain of Fars, and is
surrounded with Limestone Mountains (Asmari formation). Shiraz
area is located in Calcareous areas. The infrastructure of this city is
lime and absorbing wells that the city can influence the Limestone
dissolution and those accelerate its rate and increase the cavitation
below the surface. Dasht-e Arjan is a graben, which has been created
as the result of activity of two normal faults in its east and west sides.
It is a complete sample of Karst plains (Polje) which has been created
with the help of tectonic forces (fault) and dissolution process of
water in Asmari limestone formation. It is located 60km. off south
west of Shiraz (on Kazeroon-Shiraz road). In 1971, UNESCO has
recognized this plain as a reserve of biosphere. It is considered as one
of the world’s most beautiful geological phenomena, so that most of
the world’s geologists are interested in visiting this place. The
purpose of this paper is to identify and introduce landscapes of Karst
features shiraz city and Dasht-e Arjan including Karst dissolution
features (Lapiez, Karst springs, dolines, caves, underground caves,
ponors, and Karst valleys), anticlines and synclines, and Arjan Lake.
Abstract: An exploration of the related literature reveals that all
instruction methods aim at training autonomous learners. After the
turn of second language pedagogy toward learner-oriented strategies,
learners’ needs were more focused. Yet; the historical, social and
political aspects of learning were still neglected. The present study
investigates the notion of autonomous learning and explains its
various facets from a pedagogical point of view. Furthermore;
different elements, fields and scopes of autonomous learning will be
explored. After exploring different aspects of autonomy, it is
postulated that liberatory autonomy is highlighted since it not only
covers social autonomy but also reveals learners’ capabilities and
human potentials. It is also recommended that learners consider
different elements of autonomy such as motivation, knowledge,
confidence, and skills.
Abstract: This paper impart the design and testing of
Nanotechnology based sequential circuits using multiplexer
conservative QCA (MX-CQCA) logic gates, which is easily testable
using only two vectors. This method has great prospective in the
design of sequential circuits based on reversible conservative logic
gates and also smashes the sequential circuits implemented in
traditional gates in terms of testability. Reversible circuits are similar
to usual logic circuits except that they are built from reversible gates.
Designs of multiplexer conservative QCA logic based two vectors
testable double edge triggered (DET) sequential circuits in VHDL
language are also accessible here; it will also diminish intricacy in
testing side. Also other types of sequential circuits such as D, SR, JK
latches are designed using this MX-CQCA logic gate. The objective
behind the proposed design methodologies is to amalgamate
arithmetic and logic functional units optimizing key metrics such as
garbage outputs, delay, area and power. The projected MX-CQCA
gate outshines other reversible gates in terms of the intricacy, delay.
Abstract: Environmental impacts of six 3D printers using
various materials were compared to determine if material choice
drove sustainability, or if other factors such as machine type, machine
size, or machine utilization dominate. Cradle-to-grave life-cycle
assessments were performed, comparing a commercial-scale FDM
machine printing in ABS plastic, a desktop FDM machine printing in
ABS, a desktop FDM machine printing in PET and PLA plastics, a
polyjet machine printing in its proprietary polymer, an SLA machine
printing in its polymer, and an inkjet machine hacked to print in salt
and dextrose. All scenarios were scored using ReCiPe Endpoint H
methodology to combine multiple impact categories, comparing
environmental impacts per part made for several scenarios per
machine. Results showed that most printers’ ecological impacts were
dominated by electricity use, not materials, and the changes in
electricity use due to different plastics was not significant compared
to variation from one machine to another. Variation in machine idle
time determined impacts per part most strongly. However, material
impacts were quite important for the inkjet printer hacked to print in
salt: In its optimal scenario, it had up to 1/38th the impacts coreper
part as the worst-performing machine in the same scenario. If salt
parts were infused with epoxy to make them more physically robust,
then much of this advantage disappeared, and material impacts
actually dominated or equaled electricity use. Future studies should
also measure DMLS and SLS processes / materials.
Abstract: Passing the entrance exam to a university is a major
step in one's life. University entrance exam commonly known as
Kankor is the nationwide entrance exam in Afghanistan. This
examination is prerequisite for all public and private higher education
institutions at undergraduate level. It is usually taken by students who
are graduated from high schools. In this paper, we reflect the major
educational school graduates issues and propose ICT-based test
preparation environment, known as ‘Online Kankor Exam Prep
System’ to give students the tools to help them pass the university
entrance exam on the first try. The system is based on Intelligent
Tutoring System (ITS), which introduced an essential package of
educational technology for learners that features: (I) exam-focused
questions and content; (ii) self-assessment environment; and (iii) test
preparation strategies in order to help students to acquire the necessary
skills in their carrier and keep them up-to-date with instruction.
Abstract: In this paper, effect of marginal quality groundwater
on yield of cotton crop and soil salinity was studied. In this
connection, three irrigation treatments each with four replications
were applied. These treatments were i) use of canal water (T1), ii) use
of marginal quality groundwater from tubewell (T2), and iii)
conjunctive use by mixing with the ratio of 1:1 of canal water and
marginal quality tubewell water (T3).
Water was applied to the crop cultivated in Kharif season 2011; its
quantity has been measured using cut-throat flume. Total 11 watering
each of 50 mm depth have been applied from 20th April to 20th July,
2011. Further, irrigations were stopped due to monsoon rainfall up to
crop harvesting.
Maximum crop yield (seed cotton) was observed under T1 which
was 1,517 kg/ha followed by T3 (mixed canal and tubewell water)
having 1009 kg/ha and T2 i.e. marginal quality groundwater having
709 kg/ha. This concludes that crop yield in T2 and T3 in comparison
to T1was reduced by about 53 and 30% respectively.
It has been observed that yield of cotton crop is below potential
limit for three treatments due to unexpected rainfall at the time of full
flowering season; thus the yield was adversely affected.
However, salt deposition in soil profiles was not observed that is
due to leaching effect of heavy rainfall occurred during monsoon
season.
Abstract: Liposome plays an important role in medical and
pharmaceutical science as e.g. nano scale drug carriers. Liposomes
are vesicles of varying size consisting of a spherical lipid bilayer and
an aqueous inner compartment. Magnet-driven liposome used for the
targeted delivery of drugs to organs and tissues. These liposome
preparations contain encapsulated drug components and finely
dispersed magnetic particles.
Liposomes are vesicles of varying size consisting of a spherical
lipid bilayer and an aqueous inner compartment that are generated in
vitro. These are useful in terms of biocompatibility, biodegradability,
and low toxicity, and can control biodistribution by changing the size,
lipid composition, and physical characteristics. Furthermore,
liposomes can entrap both hydrophobic and hydrophilic drugs and are
able to continuously release the entrapped substrate, thus being useful
drug carriers. Magnetic liposomes (MLs) are phospholipid vesicles
that encapsulate magneticor paramagnetic nanoparticles. They are
applied as contrast agents for magnetic resonance imaging (MRI).
The biological synthesis of nanoparticles using plant extracts plays
an important role in the field of nanotechnology. Green-synthesized
magnetite nanoparticles-protein hybrid has been produced by treating
Iron (III) / Iron (II) chloride with the leaf extract of Datura inoxia.
The phytochemicals present in the leaf extracts act as a reducing as
well stabilizing agents preventing agglomeration, which include
flavonoids, phenolic compounds, cardiac glycosides, proteins and
sugars.
The magnetite nanoparticles-protein hybrid has been trapped
inside the aqueous core of the liposome prepared by reversed phase
evaporation (REV) method using oleic and linoleic acid which has
been shown to be driven under magnetic field confirming the
formation magnetic liposome (ML). Chemical characterization of
stealth magnetic liposome has been performed by breaking the
liposome and release of magnetic nanoparticles. The presence iron
has been confirmed by colour complex formation with KSCN and
UV-Vis study using spectrophotometer Cary 60, Agilent.
This magnet driven liposome using nanoparticles-protein hybrid
can be a smart vesicles for the targeted drug delivery.
Abstract: Geopolymer concretes are new class of construction
materials that have emerged as an alternative to Ordinary Portland
cement concrete. Considerable researches have been carried out on
material development of geopolymer concrete; however, a few studies
have been reported on the structural use of them. This paper presents
the bond behaviors of reinforcement embedded in fly ash based
geopolymer concrete. The development lengths of reinforcement for
various compressive strengths of concrete, 20, 30 and 40 MPa, and
reinforcement diameters, 10, 16 and 25 mm, are investigated. Total 27
specimens were manufactured and pull-out test according to EN 10080
was applied to measure bond strength and slips between concrete and
reinforcements. The average bond strengths decreased from 23.06MPa
to 17.26 MPa, as the diameters of reinforcements increased from
10mm to 25mm. The compressive strength levels of geopolymer
concrete showed no significant influence on bond strengths in this
study. Also, the bond-slip relations between geopolymer concrete and
reinforcement are derived using non-linear regression analysis for
various experimental conditions.
Abstract: We present a trigonometric scheme to approximate a
circular arc with its two end points and two end tangents/unit
tangents. A rational cubic trigonometric Bézier curve is constructed
whose end control points are defined by the end points of the circular
arc. Weight functions and the remaining control points of the cubic
trigonometric Bézier curve are estimated by variational approach to
reproduce a circular arc. The radius error is calculated and found less
than the existing techniques.