Abstract: Aggregation behavior of sodium salicylate and sodium cumene sulfonate was studied in aqueous solution at different temperature. Specific conductivity and relative viscosity were measured at different temperature to find minimum hydrotropic concentration. The thermodynamic parameters (free energy, enthalpy and entropy) were evaluated in the temperature range of 30°C-70°C. The free energy decreased with increase in temperature. The aggregation was found to be exothermic in nature and favored by positive value of entropy.
Abstract: The study of the fouling deposition of pink guava
juice (PGJ) is relatively new research compared to milk fouling
deposit. In this work, a new experimental set-up was developed to
imitate the fouling formation in heat exchanger, namely a continuous
flow experimental set-up heat exchanger. The new experimental setup
was operated under industrial pasteurization temperature of PGJ,
which was at 93°C. While the flow rate and pasteurization period
were based on the experimental capacity, which were 0.5 and 1
liter/min for the flow rate and the pasteurization period was set for 1
hour. Characterization of the fouling deposit was determined by
using various methods. Microstructure of the deposits was carried
out using ESEM. Proximate analyses were performed to determine
the composition of moisture, fat, protein, fiber, ash and carbohydrate
content. A study on the hardness and stickiness of the fouling deposit
was done using a texture analyzer. The presence of seedstone in pink
guava juice was also analyzed using a particle analyzer. The findings
shown that seedstone from pink guava juice ranging from 168 to
200μm and carbohydrate was found to be a major composition
(47.7% of fouling deposit consists of carbohydrate). Comparison
between the hardness and stickiness of the deposits at two different
flow rates showed that fouling deposits were harder and denser at
higher flow rate. Findings from this work provide basis knowledge
for further study on fouling and cleaning of PGJ.
Abstract: 98% of the energy needed in Taiwan has been
imported. The prices of petroleum and electricity have been
increasing. In addition, facility capacity, amount of electricity
generation, amount of electricity consumption and number of Taiwan
Power Company customers have continued to increase. For these
reasons energy conservation has become an important topic. In the
past linear regression was used to establish the power consumption
models for chillers. In this study, grey prediction is used to evaluate
the power consumption of a chiller so as to lower the total power
consumption at peak-load (so that the relevant power providers do not
need to keep on increasing their power generation capacity and facility
capacity).
In grey prediction, only several numerical values (at least four
numerical values) are needed to establish the power consumption
models for chillers. If PLR, the temperatures of supply chilled-water
and return chilled-water, and the temperatures of supply cooling-water
and return cooling-water are taken into consideration, quite accurate
results (with the accuracy close to 99% for short-term predictions)
may be obtained. Through such methods, we can predict whether the
power consumption at peak-load will exceed the contract power
capacity signed by the corresponding entity and Taiwan Power
Company. If the power consumption at peak-load exceeds the power
demand, the temperature of the supply chilled-water may be adjusted
so as to reduce the PLR and hence lower the power consumption.
Abstract: The purpose of this study is to suggest direction for
future study of the energy-IT industry that will be used for framework to increase IT utilization in the energy industry. Recently, Green IT is a becoming global issue because of global environmental pollution.
Also, IT roles in energy industry are becoming more important.
However, the related studies were IT industry oriented that is not sufficient to make plan for Green energy. Therefore, after analyzing
existing studies related to Green energy and Green IT,
re-categorization for Green energy-IT industry was suggested. Direction of framework is based on energy industry that enable to link between energy and IT. The results of this study suggest comprehensive insight to Green energy-IT industry. Thus it is able to
provide useful implications and guidelines to increase IT utilization in the energy industry.
Abstract: According to the Auckland climate, building passive
design more focus on improving winter indoor thermal and health
conditions. Based on field study data of indoor air temperature and
relative humidity close to ceiling and floor of an insulated Auckland
townhouse with and without a whole home mechanical ventilation
system, this study is to analysis variation of indoor microclimate data
of an Auckland townhouse using or not using the mechanical
ventilation system to evaluate winter indoor thermal and health
conditions for the future house design with a mechanical ventilation
system.
Abstract: The aim of this study is to examine the reading
comprehension scores of Turkish 5th grade students according to the
variables given in the student questionnaire. In this descriptive
survey study research participated 279 5th grade students, who
studied at 10 different primary schools in four provinces of Ankara in
2008-2009 academic year. Two different data collection tools were
made use of in the study: “Reading Comprehension Test" and
“Student Information Questionnaire". Independent sample t-test, oneway
Anova and two-way Anova tests were used in the analyses of
the gathered data. The results of the study indicate that the reading
comprehension scores of the students differ significantly according to
sex of the students, the number of books in their houses, the
frequency of summarizing activities on the reading text of free and
the frequency reading hours provided by their teachers; but, differ
not significantly according to educational level of their mothers and
fathers.
Abstract: This paper is a part of research, in which the way the
biomedical engineers follow in their work is analyzed. The goal of
this paper is to present a method for specification of user
requirements in the medical devices maintenance process. Data
Gathering Methods, Research Model Phases and Descriptive
Analysis is presented. These technology and verification rules can be
implemented in Medical devices maintenance management process to
the maintenance process.
Abstract: SeqWord Gene Island Sniffer, a new program for
the identification of mobile genetic elements in sequences of bacterial chromosomes is presented. This program is based on the
analysis of oligonucleotide usage variations in DNA sequences. 3,518 mobile genetic elements were identified in 637 bacterial
genomes and further analyzed by sequence similarity and the
functionality of encoded proteins. The results of this study are stored in an open database http://anjie.bi.up.ac.za/geidb/geidbhome.
php). The developed computer program and the database provide the information valuable for further investigation of the
distribution of mobile genetic elements and virulence factors among bacteria. The program is available for download at www.bi.up.ac.za/SeqWord/sniffer/index.html.
Abstract: This study aims to segment objects using the K-means
algorithm for texture features. Firstly, the algorithm transforms color
images into gray images. This paper describes a novel technique for
the extraction of texture features in an image. Then, in a group of
similar features, objects and backgrounds are differentiated by using
the K-means algorithm. Finally, this paper proposes a new object
segmentation algorithm using the morphological technique. The
experiments described include the segmentation of single and multiple
objects featured in this paper. The region of an object can be
accurately segmented out. The results can help to perform image
retrieval and analyze features of an object, as are shown in this paper.
Abstract: In this research, we study a control method of a multivehicle
system while considering the limitation of communication
range for each vehicles. When we control networked vehicles with
limitation of communication range, it is important to control the
communication network structure of a multi-vehicle system in order
to keep the network-s connectivity. From this, we especially aim to
control the network structure to the target structure. We formulate
the networked multi-vehicle system with some disturbance and the
communication constraints as a hybrid dynamical system, and then
we study the optimal control problems of the system. It is shown
that the system converge to the objective network structure in finite
time when the system is controlled by the receding horizon method.
Additionally, the optimal control probrems are convertible into the
mixed integer problems and these problems are solvable by some
branch and bound algorithm.
Abstract: Agricultural residue such as oil palm fronds (OPF) is
cheap, widespread and available throughout the year. Hemicelluloses
extracted from OPF can be hydrolyzed to their monomers and used in
production of xylooligosaccharides (XOs). The objective of the
present study was to optimize the enzymatic hydrolysis process of
OPF hemicellulose by varying pH, temperature, enzyme and substrate
concentration for production of XOs. Hemicelluloses was extracted
from OPF by using 3 M potassium hydroxide (KOH) at temperature of
40°C for 4 hrs and stirred at 400 rpm. The hemicellulose was then
hydrolyzed using Trichoderma longibrachiatum xylanase at different
pH, temperature, enzyme and substrate concentration. XOs were
characterized based on reducing sugar determination. The optimum
conditions to produced XOs from OPF hemicellulose was obtained at
pH 4.6, temperature of 40°C , enzyme concentration of 2 U/mL and
2% substrate concentration. The results established the suitability of
oil palm fronds as raw material for production of XOs.
Abstract: The coastal sediments of West Port of Malaysia was monitored from Nov. 2009 to Oct. 2010 to assess spatial distribution of heavy metals As, Cu, Cd, Cr, Hg, Ni, Zn and Pb. Sediment samples were collected from 10 stations in dry and rainy season in West Port. The range concentrations measured (Mg/g dry weight ) were from 23.4 to 98.3 for Zn, 22.3 to 80 for Pb, 7.4 to 27.6 Cu, 0.244 to 3.53 for Cd, 7.2 to 22.2 for Ni, 20.2 to 162 for As, 0.11 to 0.409 for Hg and 11.5 to 61.5 for Cr. The geochemical indexes used in this study were Geoaccumulation (Igeo), Contamination Factor (CF) and Pollution Load Index (PLI); these indexes were used to evaluate the levels of sediment contaminations. The results of these indexes show that, the status of West Port sediment quality are moderately polluted by heavy metals except in arsenic which shows the high level of pollution.
Abstract: The purpose of this study is to discuss the effect of the
intervention of exercise behavior change plan for high school students
on study subjects- social and psychological factors and exercise
stages. This research uses the transtheoretical model as the research
framework. One experiment group and one control group were used in
a quasi-experimental design research. The experimental group
accepted health-related physical fitness course and the traditional
course; the control group accepted traditional physical education
course. There is a significant difference before and after the
intervention in the experimental group. Karl-s test shows the
experimental group gained a better improvement than that in the
control group. The Analysis of Covariance had shown the exercise
stages (F=7.62, p
Abstract: Using Dynamic Bayesian Networks (DBN) to model genetic regulatory networks from gene expression data is one of the major paradigms for inferring the interactions among genes. Averaging a collection of models for predicting network is desired, rather than relying on a single high scoring model. In this paper, two kinds of model searching approaches are compared, which are Greedy hill-climbing Search with Restarts (GSR) and Markov Chain Monte Carlo (MCMC) methods. The GSR is preferred in many papers, but there is no such comparison study about which one is better for DBN models. Different types of experiments have been carried out to try to give a benchmark test to these approaches. Our experimental results demonstrated that on average the MCMC methods outperform the GSR in accuracy of predicted network, and having the comparable performance in time efficiency. By proposing the different variations of MCMC and employing simulated annealing strategy, the MCMC methods become more efficient and stable. Apart from comparisons between these approaches, another objective of this study is to investigate the feasibility of using DBN modeling approaches for inferring gene networks from few snapshots of high dimensional gene profiles. Through synthetic data experiments as well as systematic data experiments, the experimental results revealed how the performances of these approaches can be influenced as the target gene network varies in the network size, data size, as well as system complexity.
Abstract: All over the world, including the Middle and East
European countries, sustainable tillage and sowing technologies are
applied increasingly broadly with a view to optimising soil resources,
mitigating soil degradation processes, saving energy resources,
preserving biological diversity, etc. As a result, altered conditions of
tillage and sowing technological processes are faced inevitably. The
purpose of this study is to determine the seedbed topsoil hardness
when using a combined sowing coulter in different sustainable tillage
technologies. The research involved a combined coulter consisting
of two dissected blade discs and a shoe coulter. In order to determine
soil hardness at the seedbed area, a multipenetrometer was used. It
was found by experimental studies that in loosened soil, a combined
sowing coulter equally suppresses the furrow bottom, walls and soil
near the furrow; therefore, here, soil hardness was similar at all
researched depths and no significant differences were established. In
loosened and compacted (double-rolled) soil, the impact of a
combined coulter on the hardness of seedbed soil surface was more
considerable at a depth of 2 mm. Soil hardness at the furrow bottom
and walls to a distance of up to 26 mm was 1.1 MPa. At a depth of 10
mm, the greatest hardness was established at the furrow bottom. In
loosened and heavily compacted (rolled for 6 times) soil, at a depth
of 2 and 10 mm a combined coulter most of all compacted the furrow
bottom, which has a hardness of 1.8 MPa. At a depth of 20 mm, soil
hardness within the whole investigated area varied insignificantly and
fluctuated by around 2.0 MPa. The hardness of furrow walls and soil
near the furrow was by approximately 1.0 MPa lower than that at the
furrow bottom
Abstract: The present microfluidic study is emphasizing the flow behavior within a Y shape micro-bifurcation in two similar flow configurations. We report here a numerical and experimental investigation on the velocity profiles evolution and secondary flows, manifested at different Reynolds numbers (Re) and for two different boundary conditions. The experiments are performed using special designed setup based on optical microscopic devices. With this setup, direct visualizations and quantitative measurements of the path-lines are obtained. A Micro-PIV measurement system is used to obtain velocity profiles distributions in a spatial evolution in the main flows domains. The experimental data is compared with numerical simulations performed with commercial computational code FLUENT in a 3D geometry with the same dimensions as the experimental one. The numerical flow patterns are found to be in good agreement with the experimental manifestations.
Abstract: Leptospirosis occurs worldwide (except the
poles of the earth), urban and rural areas, developed and
developing countries, especially in Thailand. It can be
transmitted to the human by rats through direct and indirect
ways. Human can be infected by either touching the infected rats
or contacting with water, soil containing urine from the infected
rats through skin, eyes and nose. The data of the people who
are infected with this disease indicates that most of the
patients are adults. The transmission of this disease is studied
through mathematical model. The population is separated into human
and rat. The human is divided into two classes, namely juvenile
and adult. The model equation is constructed for each class. The
standard dynamical modeling method is then used for
analyzing the behaviours of solutions. In addition, the
conditions of the parameters for the disease free and endemic
states are obtained. Numerical solutions are shown to support the
theoretical predictions. The results of this study guide the way to
decrease the disease outbreak.
Abstract: The photochemical and photo-Fenton oxidation of 1,3-dichloro-2-propanol was performed in a batch reactor, at room temperature, using UV radiation, H2O2 as oxidant, and Fenton-s reagent. The effect of the oxidative agent-s initial concentration was investigated as well as the effect of the initial concentration of Fe(II) by following the target compound degradation, the total organic carbon removal and the chloride ion production. Also, from the kinetic analysis conducted and proposed reaction scheme it was deduced that the addition of Fe(II) significantly increases the production and the further oxidation of the chlorinated intermediates.
Abstract: The aim of this study is to investigate the effect of
perceived social support and stress on the coping capability and level
of depression of foreign and local students in Malaysia. Using
convenience sampling, 200 students from three universities in
Selangor, Malaysia participated in the study. The results of this study
revealed that there was a significant relationship between perceived
social support and coping capability. It is also found that there is a
negative relationship between coping capability and depression.
Further, stress and depression are positively related whereas stress
and coping capability are negatively related. Lastly, there is no
significant difference for the stress level and coping capability
amongst local and foreign students.
Abstract: A new dual-fluid concept was studied that could eventually find application for cold-gas propulsion for small space satellites or other constant flow applications. In basic form, the concept uses two different refrigerant working fluids, each having a different saturation vapor pressure. The higher vapor pressure refrigerant remains in the saturation phase and is used to pressurize the lower saturation vapor pressure fluid (the propellant) which remains in the compressed liquid phase. A demonstration thruster concept based on this principle was designed and built to study its operating characteristics. An automotive-type electronic fuel injector was used to meter and deliver the propellant. Ejected propellant mass and momentum were measured for several combinations of refrigerants and hydrocarbon fluids. The thruster has the advantage of delivering relatively large total impulse at low tank pressure within a small volume.