Abstract: In the present work, we propose a new method for
solving the matrix equation AXB=F . The new method can
be considered as a generalized form of the well-known global full
orthogonalization method (Gl-FOM) for solving multiple linear
systems. Hence, the method will be called extended Gl-FOM (EGl-
FOM). For implementing EGl-FOM, generalized forms of block
Krylov subspace and global Arnoldi process are presented. Finally,
some numerical experiments are given to illustrate the efficiency of
our new method.
Abstract: In countries with hot climates, air-conditioning forms
a large proportion of annual peak electrical demand, requiring
expansion of power plants to meet the peak demand, which goes
unused most of the time. Use of well-designed cool storage can offset
the peak demand to a large extent. In this study, an air conditioning
system with naturally stratified storage tank was designed,
constructed and tested. A new type of diffuser was designed and used
in this study. Factors that influence the performance of chilled water
storage tanks were investigated. The results indicated that stratified
storage tank consistently stratified well without any physical barrier.
Investigation also showed that storage efficiency decreased with
increasing flow rate due to increased mixing of warm and chilled
water. Diffuser design and layout primarily affected the mixing near
the inlet diffuser and the extent of this mixing had primary influence
on the shape of the thermocline. The heat conduction through tank
walls and through the thermocline caused widening of mixed volume.
Thermal efficiency of stratified storage tanks was as high as 90
percent, which indicates that stratified tanks can effectively be used
as a load management technique.
Abstract: In this paper a new cost function for blind equalization
is proposed. The proposed cost function, referred to as the modified
maximum normalized cumulant criterion (MMNC), is an extension
of the previously proposed maximum normalized cumulant criterion
(MNC). While the MNC requires a separate phase recovery system
after blind equalization, the MMNC performs joint blind equalization
and phase recovery. To achieve this, the proposed algorithm
maximizes a cost function that considers both amplitude and phase of
the equalizer output. The simulation results show that the proposed
algorithm has an improved channel equalization effect than the MNC
algorithm and simultaneously can correct the phase error that the
MNC algorithm is unable to do. The simulation results also show that
the MMNC algorithm has lower complexity than the MNC algorithm.
Moreover, the MMNC algorithm outperforms the MNC algorithm
particularly when the symbols block size is small.
Abstract: The Wind Turbine Modeling in Wind Energy Conversion System (WECS) using Doubly-Fed Induction Generator (DFIG) PI Controller based design is presented. To study about the variable wind speed. The PI controller performs responding to the dynamic performance. The objective is to study the characteristic of wind turbine and finding the optimum wind speed suitable for wind turbine performance. This system will allow the specification setting (2.5MW). The output active power also corresponding same the input is given. And the reactive power produced by the wind turbine is regulated at 0 Mvar. Variable wind speed is optimum for drive train performance at 12.5 m/s (at maximum power coefficient point) from the simulation of DFIG by Simulink is described.
Abstract: Signature represents an individual characteristic of a
person which can be used for his / her validation. For such application
proper modeling is essential. Here we propose an offline signature
recognition and verification scheme which is based on extraction of
several features including one hybrid set from the input signature
and compare them with the already trained forms. Feature points
are classified using statistical parameters like mean and variance.
The scanned signature is normalized in slant using a very simple
algorithm with an intention to make the system robust which is
found to be very helpful. The slant correction is further aided by the
use of an Artificial Neural Network (ANN). The suggested scheme
discriminates between originals and forged signatures from simple
and random forgeries. The primary objective is to reduce the two
crucial parameters-False Acceptance Rate (FAR) and False Rejection
Rate (FRR) with lesser training time with an intension to make the
system dynamic using a cluster of ANNs forming a multiple classifier
system.
Abstract: This paper proposes a novel multi-format stream grid
architecture for real-time image monitoring system. The system, based
on a three-tier architecture, includes stream receiving unit, stream
processor unit, and presentation unit. It is a distributed computing and
a loose coupling architecture. The benefit is the amount of required
servers can be adjusted depending on the loading of the image
monitoring system. The stream receive unit supports multi capture
source devices and multi-format stream compress encoder. Stream
processor unit includes three modules; they are stream clipping
module, image processing module and image management module.
Presentation unit can display image data on several different platforms.
We verified the proposed grid architecture with an actual test of image
monitoring. We used a fast image matching method with the
adjustable parameters for different monitoring situations. Background
subtraction method is also implemented in the system. Experimental
results showed that the proposed architecture is robust, adaptive, and
powerful in the image monitoring system.
Abstract: A new estimator for evolutionary spectrum (ES) based
on short time Fourier transform (STFT) and modified group delay
function (MGDF) by signal decomposition (SD) is proposed. The
STFT due to its built-in averaging, suppresses the cross terms and the
MGDF preserves the frequency resolution of the rectangular window
with the reduction in the Gibbs ripple. The present work overcomes
the magnitude distortion observed in multi-component non-stationary
signals with STFT and MGDF estimation of ES using SD. The SD is
achieved either through discrete cosine transform based harmonic
wavelet transform (DCTHWT) or perfect reconstruction filter banks
(PRFB). The MGDF also improves the signal to noise ratio by
removing associated noise. The performance of the present method is
illustrated for cross chirp and frequency shift keying (FSK) signals,
which indicates that its performance is better than STFT-MGDF
(STFT-GD) alone. Further its noise immunity is better than STFT.
The SD based methods, however cannot bring out the frequency
transition path from band to band clearly, as there will be gap in the
contour plot at the transition. The PRFB based STFT-SD shows good
performance than DCTHWT decomposition method for STFT-GD.
Abstract: An approach of design of stable of control systems with ultimately wide ranges of uncertainly disturbed parameters is offered. The method relies on using of nonlinear structurally stable functions from catastrophe theory as controllers. Theoretical part presents an analysis of designed nonlinear second-order control systems. As more important the integrators in series, canonical controllable form and Jordan forms are considered. The analysis resumes that due to added controllers systems become stable and insensitive to any disturbance of parameters. Experimental part presents MATLAB simulation of design of control systems of epidemic spread, aircrafts angular motion and submarine depth. The results of simulation confirm the efficiency of offered method of design. KeywordsCatastrophes, robust control, simulation, uncertain parameters.
Abstract: increased competition and increased costs of
designing made it important for the firms to identify the right
products and the right methods for manufacturing the products. Firms
should focus on customers and identify customer demands directly to
design the right products. Several management methods and
techniques that are currently available improve one or more functions
or processes in an industry and do not take the complete product life
cycle into consideration. On the other hand target costing is a method
/ philosophy that takes financial, manufacturing and customer aspects
into consideration during designing phase and helps firms in making
product design decisions to increase the profit / value of the
company. It uses various techniques to identify customer demands, to
decrease costs of manufacturing and finally to achieve strategic goals.
Target Costing forms an integral part of total product design /
redesign based on strategic plans.
Abstract: Re-entrant scheduling is an important search problem
with many constraints in the flow shop. In the literature, a number of
approaches have been investigated from exact methods to
meta-heuristics. This paper presents a genetic algorithm that encodes
the problem as multi-level chromosomes to reflect the dependent
relationship of the re-entrant possibility and resource consumption.
The novel encoding way conserves the intact information of the data
and fastens the convergence to the near optimal solutions. To test the
effectiveness of the method, it has been applied to the
resource-constrained re-entrant flow shop scheduling problem.
Computational results show that the proposed GA performs better than
the simulated annealing algorithm in the measure of the makespan
Abstract: Megalopolis is a group of densely populated metropolitan areas that combine to form an urban complex. Since China introduced the economic reforms in late 1970s, the Chinese urban system has experienced unprecedented growth. The process of urbanisation prevailed in the 1980s, and the process of predominantly large city growth appeared to continue through 1990s and 2000s. In this study, the magnitude and pattern of urbanisation in China during 1990s were examined using remotely sensed imagery acquired by TM/ETM+ sensor onboard the Landsat satellites. The development of megalopolis areas in China was also studied based on the GIS analysis of the increases of urban and built-up area from 1990 to 2000. The analysis suggests that in the traditional agricultural zones in China, e.g., Huang-Huai-Hai Plains, Changjiang River Delta, Pearl River Delta and Sichuan Basin, the urban and built-up areas increased by 1.76 million hectares, of which 0.82 million hectares are expansion of urban areas, an increase of 24.78% compared with 1990 at the national scale. The Yellow River Delta, Changjiang River Delta and Pearl River Delta also saw an increase of urban and built-up area by 63.9%, 66.2% and 83.0% respectively. As a result, three major megalopolises were developed in China: the Guangzhou-Shenzhen-Hong Kong- Macau (Pearl River Delta: PRD) megalopolis area, the Shanghai- Nanjing-Hangzhou (Changjiang River Delta: CRD) megalopolis area and the Beijing-Tianjing-Tangshan-Qinhuangdao (Yellow River Delta-Bohai Sea Ring: YRD) megalopolis area. The relationship between the processed of megalopolisation and the inter-provincial population flow was also explored in the context of social-economic and transport infrastructure development in Post-reform China.
Abstract: A analysis on the conventional the blood pressure estimation method using an oscillometric sphygmomanometer was
performed through a computer simulation using an arterial pressure-volume (APV) model. Traditionally, the maximum amplitude algorithm (MAP) was applied on the oscillation waveforms of the APV model to obtain the mean arterial pressure and the characteristic ratio. The estimation of mean arterial pressure and
characteristic ratio was significantly affected with the shape of the blood pressure waveforms and the cutoff frequency of high-pass filter
(HPL) circuitry. Experimental errors are due to these effects when estimating blood pressure. To find out an algorithm independent from
the influence of waveform shapes and parameters of HPL, the volume
oscillation of the APV model and the phase shift of the oscillation with fast fourier transform (FFT) were testified while increasing the cuff
pressure from 1 mmHg to 200 mmHg (1 mmHg per second). The phase shift between the ranges of volume oscillation was then only observed between the systolic and the diastolic blood pressures. The same results were also obtained from the simulations performed on two different the arterial blood pressure waveforms and one
hyperthermia waveform.
Abstract: The paper proposes a unified model for multimedia data retrieval which includes data representatives, content representatives, index structure, and search algorithms. The multimedia data are defined as k-dimensional signals indexed in a multidimensional k-tree structure. The benefits of using the k-tree unified model were demonstrated by running the data retrieval application on a six networked nodes test bed cluster. The tests were performed with two retrieval algorithms, one that allows parallel searching using a single feature, the second that performs a weighted cascade search for multiple features querying. The experiments show a significant reduction of retrieval time while maintaining the quality of results.
Abstract: This study describes the methodology for the development of a validated in-vitro in-vivo correlation (IVIVC) for metoprolol tartrate modified release dosage forms with distinctive release rate characteristics. Modified release dosage forms were formulated by microencapsulation of metoprolol tartrate into different amounts of ethylcellulose by non-solvent addition technique. Then in-vitro and in-vivo studies were conducted to develop and validate level A IVIVC for metoprolol tartrate. The values of regression co-efficient (R2-values) for IVIVC of T2 and T3 formulations were not significantly (p
Abstract: In this paper a new Genetic Algorithm based on a heuristic operator and Centre of Mass selection operator (CMGA) is designed for the unbounded knapsack problem(UKP), which is NP-Hard combinatorial optimization problem. The proposed genetic algorithm is based on a heuristic operator, which utilizes problem specific knowledge. This center of mass operator when combined with other Genetic Operators forms a competitive algorithm to the existing ones. Computational results show that the proposed algorithm is capable of obtaining high quality solutions for problems of standard randomly generated knapsack instances. Comparative study of CMGA with simple GA in terms of results for unbounded knapsack instances of size up to 200 show the superiority of CMGA. Thus CMGA is an efficient tool of solving UKP and this algorithm is competitive with other Genetic Algorithms also.
Abstract: Number of documents being created increases at an
increasing pace while most of them being in already known topics
and little of them introducing new concepts. This fact has started a
new era in information retrieval discipline where the requirements
have their own specialties. That is digging into topics and concepts
and finding out subtopics or relations between topics. Up to now IR
researches were interested in retrieving documents about a general
topic or clustering documents under generic subjects. However these
conventional approaches can-t go deep into content of documents
which makes it difficult for people to reach to right documents they
were searching. So we need new ways of mining document sets
where the critic point is to know much about the contents of the
documents. As a solution we are proposing to enhance LSI, one of
the proven IR techniques by supporting its vector space with n-gram
forms of words. Positive results we have obtained are shown in two
different application area of IR domain; querying a document
database, clustering documents in the document database.
Abstract: Logic based methods for learning from structured data
is limited w.r.t. handling large search spaces, preventing large-sized
substructures from being considered by the resulting classifiers. A
novel approach to learning from structured data is introduced that
employs a structure transformation method, called finger printing, for
addressing these limitations. The method, which generates features
corresponding to arbitrarily complex substructures, is implemented in
a system, called DIFFER. The method is demonstrated to perform
comparably to an existing state-of-art method on some benchmark
data sets without requiring restrictions on the search space.
Furthermore, learning from the union of features generated by finger
printing and the previous method outperforms learning from each
individual set of features on all benchmark data sets, demonstrating
the benefit of developing complementary, rather than competing,
methods for structure classification.
Abstract: Modern culture, based on disinhibition of cultural trends and on heterodirection, is promoting openmindedness attitudes towards ethnic diversity, but on the other hand also new forms of social representations of the foreigner. Social representation is situated between the psychic field and the social one; it is the representation of oneself and of the other one, hanging between social categories and individual inner world. We will produce the results of a research on the representation of the foreigner, built on the type of prejudice prevailing among middle-low or middle-high educational qualification subjects, in which prejudicial attitudes seem to descend from precise mental images of the foreigner.
Abstract: This article explores the self-identity of the Kazakh
people by way of identifying the roots of self-understanding in
Kazakh culture. Unfortunately, Western methods of ethno
psychology cannot fully capture what is unique about identity in
Kazakh culture. Although Kazakhstan is the ninth largest country in
terms of geographical space, Kazakh cultural identity is not wellknown
in the West. In this article we offer an account of the national
psychological features of the Kazakh people, in order to reveal the
spiritual, mental, ethical dimensions of modern Kazakhs. These
factors play a central role in the revival of forms of identity that are
central to the Kazakh people.
Abstract: This communication is intended to provide some issues for thought on the importance of implementation of Blended Learning in traditional universities, particularly in the Spanish university system. In this respect, we believe that virtual environments are likely to meet some of the needs raised by the Bologna agreement, trying to maintain the quality of teaching and at the same time taking advantage of the functionalities that virtual learning platforms offer. We are aware that an approach of learning from an open and constructivist nature in universities is a complex process that faces significant technological, administrative and human barriers. Therefore, in order to put plans in our universities, it is necessary to analyze the state of the art of some indicators relating to the use of ICT, with special attention to virtual teaching and learning, so that we can identify the main obstacles and design adaptive strategies for their full integration in the education system. Finally, we present major initiatives launched in the European and state framework for the effective implementation of new virtual environments in the area of higher education.