Abstract: This study was an investigation on the suitability of Lahar/HDPE composite as a primary material for low-cost smallscale biogas digesters. While sources of raw materials for biogas are abundant in the Philippines, cost of the technology has made the widespread utilization of this resource an indefinite proposition. Aside from capital economics, another problem arises with space requirements of current digester designs. These problems may be simultaneously addressed by fabricating digesters on a smaller, household scale to reach a wider market, and to use materials that may accommodate optimization of overall design and fabrication cost without sacrificing operational efficiency. This study involved actual fabrication of the Lahar/HDPE composite at varying composition and geometry, subsequent mechanical and thermal characterization, and implementation of Statistical Analysis to find intrinsic relationships between variables. From the results, Lahar/HDPE composite was found to be feasible for use as digester material from both mechanical and economic standpoints.
Abstract: A challenged control problem is when the
performance is pushed to the limit. The state-derivative feedback
control strategy directly uses acceleration information for feedback
and state estimation. The derivative part is concerned with the rateof-
change of the error with time. If the measured variable approaches
the set point rapidly, then the actuator is backed off early to allow it
to coast to the required level. Derivative action makes a control
system behave much more intelligently. A sensor measures the
variable to be controlled and the measured in formation is fed back to
the controller to influence the controlled variable. A high gain
problem can be also formulated for proportional plus derivative
feedback transformation. Using MATLAB Simulink dynamic
simulation tool this paper examines a system with a proportional plus
derivative feedback and presents an automatic implementation of
finding an acceptable controlled system. Using feedback
transformations the system is transformed into another system.
Abstract: Robust stability and performance are the two most
basic features of feedback control systems. The harmonic balance
analysis technique enables to analyze the stability of limit cycles
arising from a neural network control based system operating over
nonlinear plants. In this work a robust stability analysis based on the
harmonic balance is presented and applied to a neural based control
of a non-linear binary distillation column with unstructured
uncertainty. We develop ways to describe uncertainty in the form of
neglected nonlinear dynamics and high harmonics for the plant and
controller respectively. Finally, conclusions about the performance of
the neural control system are discussed using the Nyquist stability
margin together with the structured singular values of the uncertainty
as a robustness measure.
Abstract: The national economy development affects the vehicle
ownership which ultimately increases fuel consumption. The rise of
the vehicle ownership is dominated by the increasing number of
motorcycles. This research aims to analyze and identify the
characteristics of fuel consumption, the city transportation system,
and to analyze the relationship and the effect of the city
transportation system on the fuel consumption. A multivariable
analysis is used in this study. The data analysis techniques include: a
Multivariate Multivariable Analysis by using the R software. More
than 84% of fuel on Java is consumed in metropolitan and large
cities. The city transportation system variables that strongly effect the
fuel consumption are population, public vehicles, private vehicles and
private bus. This method can be developed to control the fuel
consumption by considering the urban transport system and city
tipology. The effect can reducing subsidy on the fuel consumption,
increasing state economic.
Abstract: Ascorbic acid (AA), commonly known as vitamin C, is essential for normal functioning of the body and maintenance of metabolic integrity. Among its various roles are as an antioxidant, a cofactor in collagen formation and other reactions, as well as reducing physical stress and maintenance of the immune system. Recent collaborative research between the Australian Defence Science and Technology Organisation (DSTO) in Scottsdale, Tasmania and RMIT University has sought to overcome the problems arising from the inherent instability of ascorbic acid during processing and storage of foods. The recent work has demonstrated the potential of microencapsulation by spray drying as a means to enhance retention. The purpose of this current study has been focused upon the influence of spray drying conditions on the properties of encapsulated ascorbic acid. The process was carried out according to a central composite design. Independent variables were: inlet temperature (80-120° C) and feed flow rate (7-14 mL/minute). Process yield, ascorbic acid loss, moisture content, water activity and particle size distribution were analysed as responses. The results have demonstrated the potential of microencapsulation by spray drying as a means to enhance retention. Vitamin retention, moisture content, water activity and process yield were influenced positively by inlet air temperature and negatively by feed flow rate.
Abstract: This contribution was developed from a research
within the doctoral thesis. Its object was to create multimedia
materials for sport gymnastics. Consequently we surveyed the
influence of its practical application on the efficiency of schooling at
a university. We verified the prescribed hypothesis of the efficiency
of the teaching process using the method of single-factor experiment,
where the entrance independent variable was the change of system of
tuition and the outgoing dependent variable was the change of level
of acquired motor skills. The results confirmed the positive impact of
using multimedia materials on the efficiency of the teaching process.
Further, with the aid of questionnaires, we evaluated how the tested
subjects perceive the innovative methods in sport gymnastics. The
responses showed that the students rate the application of multimedia
materials very positively.
Abstract: Microscopic emission and fuel consumption models
have been widely recognized as an effective method to quantify real
traffic emission and energy consumption when they are applied with
microscopic traffic simulation models. This paper presents a
framework for developing the Microscopic Emission (HC, CO, NOx,
and CO2) and Fuel consumption (MEF) models for light-duty
vehicles. The variable of composite acceleration is introduced into
the MEF model with the purpose of capturing the effects of historical
accelerations interacting with current speed on emission and fuel
consumption. The MEF model is calibrated by multivariate
least-squares method for two types of light-duty vehicle using
on-board data collected in Beijing, China by a Portable Emission
Measurement System (PEMS). The instantaneous validation results
shows the MEF model performs better with lower Mean Absolute
Percentage Error (MAPE) compared to other two models. Moreover,
the aggregate validation results tells the MEF model produces
reasonable estimations compared to actual measurements with
prediction errors within 12%, 10%, 19%, and 9% for HC, CO, NOx
emissions and fuel consumption, respectively.
Abstract: Let Xi be a Lacunary System, we established large
deviations inequality for Lacunary System. Furthermore, we gained
Marcinkiewicz Larger Number Law with dependent random variables
sequences.
Abstract: In this paper, an automatic system of diagnosis was
developed to detect and locate in real time the defects of the wound
rotor asynchronous machine associated to electronic converter. For
this purpose, we have treated the signals of the measured parameters
(current and speed) to use them firstly, as indicating variables of the
machine defects under study and, secondly, as inputs to the Artificial
Neuron Network (ANN) for their classification in order to detect the
defect type in progress. Once a defect is detected, the interpretation
system of information will give the type of the defect and its place of
appearance.
Abstract: An adaptive dynamic cerebellar model articulation
controller (DCMAC) neural network used for solving the prediction
and identification problem is proposed in this paper. The proposed
DCMAC has superior capability to the conventional cerebellar model
articulation controller (CMAC) neural network in efficient learning
mechanism, guaranteed system stability and dynamic response. The
recurrent network is embedded in the DCMAC by adding feedback
connections in the association memory space so that the DCMAC
captures the dynamic response, where the feedback units act as
memory elements. The dynamic gradient descent method is adopted to
adjust DCMAC parameters on-line. Moreover, the analytical method
based on a Lyapunov function is proposed to determine the
learning-rates of DCMAC so that the variable optimal learning-rates
are derived to achieve most rapid convergence of identifying error.
Finally, the adaptive DCMAC is applied in two computer simulations.
Simulation results show that accurate identifying response and
superior dynamic performance can be obtained because of the
powerful on-line learning capability of the proposed DCMAC.
Abstract: The purpose of suspension system in automobiles is to
improve the ride comfort and road handling. In this research the ride
and handling performance of a specific automobile with passive
suspension system is compared to a proposed fuzzy logic semi active
suspension system designed for that automobile. The bodysuspension-
wheel system is modeled as a two degree of freedom
quarter car model. MATLAB/SIMULINK [1] was used for
simulation and controller design. The fuzzy logic controller is based
on two inputs namely suspension velocity and body velocity. The
output of the fuzzy controller is the damping coefficient of the
variable damper. The result shows improvement over passive
suspension method.
Abstract: Reliable water level forecasts are particularly
important for warning against dangerous flood and inundation. The
current study aims at investigating the suitability of the adaptive
network based fuzzy inference system for continuous water level
modeling. A hybrid learning algorithm, which combines the least
square method and the back propagation algorithm, is used to
identify the parameters of the network. For this study, water levels
data are available for a hydrological year of 2002 with a sampling
interval of 1-hour. The number of antecedent water level that should
be included in the input variables is determined by two statistical
methods, i.e. autocorrelation function and partial autocorrelation
function between the variables. Forecasting was done for 1-hour until
12-hour ahead in order to compare the models generalization at
higher horizons. The results demonstrate that the adaptive networkbased
fuzzy inference system model can be applied successfully and
provide high accuracy and reliability for river water level estimation.
In general, the adaptive network-based fuzzy inference system
provides accurate and reliable water level prediction for 1-hour ahead
where the MAPE=1.15% and correlation=0.98 was achieved. Up to
12-hour ahead prediction, the model still shows relatively good
performance where the error of prediction resulted was less than
9.65%. The information gathered from the preliminary results
provide a useful guidance or reference for flood early warning
system design in which the magnitude and the timing of a potential
extreme flood are indicated.
Abstract: Multi-Radio Multi-Channel (MRMC) systems are key to power control problems in wireless mesh networks (WMNs). In this paper, we present asynchronous multiple-state based power control for MRMC WMNs. First, WMN is represented as a set of disjoint Unified Channel Graphs (UCGs). Second, each network interface card (NIC) or radio assigned to a unique UCG adjusts transmission power using predicted multiple interaction state variables (IV) across UCGs. Depending on the size of queue loads and intra- and inter-channel states, each NIC optimizes transmission power locally and asynchronously. A new power selection MRMC unification protocol (PMMUP) is proposed that coordinates interactions among radios. The efficacy of the proposed method is investigated through simulations.
Abstract: The optimal extraction condition of dried
Echinocactus grusonii powder was studied. The three independent
variables are raw material drying temperature, extraction
temperature, and extraction time. The dependent variables are both
yield percentage of crude extract and total phenolic quantification as
gallic acid equivalent in crude extract. The experimental design was
based on central composite design. Highest yield percentage of crude
extract could get from extraction condition at raw material drying
temperature at 60°C, extraction temperature at 15°C, and extraction
time for 25 min °C. Moreover, the crude extract with highest phenolic
occurred by extraction condition of raw material drying temperature
at 60°C, extraction temperature at 35 °C, and extraction lasting 25
min.
Abstract: In all industries which are related to heat, suitable
thermal ranges are defined for each device to operate well.
Consideration of these limits requires a thermal control unit beside
the main system. The Satellite Thermal Control Unit exploits from
different methods and facilities individually or mixed. For enhancing
heat transfer between primary surface and the environment,
utilization of radiating extended surfaces are common. Especially for
large temperature differences; variable thermal conductivity has a
strong effect on performance of such a surface .In most literatures,
thermo-physical properties, such as thermal conductivity, are
assumed as constant. However, in some recent researches the
variation of these parameters is considered. This may be helpful for
the evaluation of fin-s temperature distribution in relatively large
temperature differences. A new method is introduced to evaluate
temperature-dependent thermal conductivity values. The finite
volume method is employed to simulate numerically the temperature
distribution in a space radiating fin. The present modeling is carried
out for Aluminum as fin material and compared with previous
method. The present results are also compared with those of two
other analytical methods and good agreement is shown.
Abstract: In this work, sorption of nickel from aqueous solution on hypnea valentiae, red macro algae, was investigated. Batch experiments have been carried out to find the effect of various parameters such as pH, temperature, sorbent dosage, metal concentration and contact time on the sorption of nickel using hypnea valentiae. Response surface methodology (RSM) is employed to optimize the process parameters. Based on the central composite design, quadratic model was developed to correlate the process variables to the response. The most influential factor on each experimental design response was identified from the analysis of variance (ANOVA). The optimum conditions for the sorption of nickel were found to be: pH – 5.1, temperature – 36.8oC, sorbent dosage – 5.1 g/L, metal concentration – 100 mg/L and contact time – 30 min. At these optimized conditions the maximum removal of nickel was found to be 91.97%. A coefficient of determination R2 value 0.9548 shows the fitness of response surface methodology in this work.
Abstract: RFID system, in which we give identification number to each item and detect it with radio frequency, supports more variable service than barcode system can do. For example, a refrigerator with RFID reader and internet connection will automatically notify expiration of food validity to us. But, in spite of its convenience, RFID system has some security threats, because anybody can get ID information of item easily. One of most critical threats is privacy invasion. Existing privacy protection schemes or systems have been proposed, and these schemes or systems defend normal users from attempts that any attacker tries to get information using RFID tag value. But, these systems still have weakness that attacker can get information using analogous value instead of original tag value. In this paper, we mention this type of attack more precisely and suggest 'Tag Broker Model', which can defend it. Tag broker in this model translates original tag value to random value, and user can only get random value. Attacker can not use analogous tag value, because he/she is not able to know original one from it.
Abstract: Collaborative planning, forecasting and
replenishment (CPFR) coordinates the various supply chain
management activities including production and purchase planning,
demand forecasting and inventory replenishment between supply
chain trading partners. This study proposes a systematic way of
analyzing CPFR supporting factors using fuzzy cognitive map
(FCM) approach. FCMs have proven particularly useful for solving
problems in which a number of decision variables and
uncontrollable variables are causally interrelated. Hence the FCMs
of CPFR are created to show the relationships between the factors
that influence on effective implementation of CPFR in the supply
chain.
Abstract: The Beshar River is one of the most important aquatic ecosystems in the upstream of the Karun watershed in south of Iran which is affected by point and non point pollutant sources . This study was done in order to evaluate the effects of pollutants activities on the water quality of the Beshar river and its aquatic ecosystems. This river is approximately 190 km in length and situated at the geographical positions of 51° 20´ to 51° 48´ E and 30° 18´ to 30° 52´ N it is one of the most important aquatic ecosystems of Kohkiloye and Boyerahmad province in south-west Iran. In this research project, five study stations were selected to examine water pollution in the Beshar River systems. Human activity is now one of the most important factors affecting on hydrology and water quality of the Beshar river. Humans use large amounts of resources to sustain various standards of living, although measures of sustainability are highly variable depending on how sustainability is defined. The Beshar river ecosystems are particularly sensitive and vulnerable to human activities. Therefore, to determine the impact of human activities on the Beshar River, the most important water quality parameters such as pH, dissolve oxygen (DO), Biological Oxygen Demand (BOD5), Total Dissolve Solids (TDS), Nitrates (NO3-N) and Phosphates (PO4) were estimated at the five stations. As the results show, the most important pollution index parameters such as BOD5, NO3 and PO4 increase and DO and pH decrease according to human activities (P
Abstract: Studies in economics domain tried to reveal the correlation between stock markets. Since the globalization era, interdependence between stock markets becomes more obvious. The Dynamic Interaction Network (DIN) algorithm, which was inspired by a Gene Regulatory Network (GRN) extraction method in the bioinformatics field, is applied to reveal important and complex dynamic relationship between stock markets. We use the data of the stock market indices from eight countries around the world in this study. Our results conclude that DIN is able to reveal and model patterns of dynamic interaction from the observed variables (i.e. stock market indices). Furthermore, it is also found that the extracted network models can be utilized to predict movement of the stock market indices with a considerably good accuracy.