Abstract: Autologous Chondrocyte Implantation (ACI) is used worldwide since 1998 to treat cartilage defect. GEL based ACI is a new tissue-engineering technique to treat full thickness cartilage defect with fibrin and thrombin as scaffold for chondrocytes. Purpose of this study is to see safety and efficacy of gel based ACI for knee cartilage defect in multiple centres with different surgeons. Gel-based Autologous Chondrocyte Implantation (GACI) has shown effectiveness in treating isolated cartilage defect of knee joint. Long term results are still needed to be studied. This study was followed-up up to two years and showed benefit to patients. All enrolled patients with a mean age of 28.5 years had an average defect size of3 square centimeters, and were grade IV as per ICRS grading. All patients were followed up several times and at several intervals at 6th week, 8th week, 11th week, 17th week, 29th week, 57th week after surgery. The outcomes were measured based on the IKDC (subjective and objective) and MOCART scores.
Abstract: Fe-2%Mn-0.5%Si-0.2C steel was welded and corroded
at 600, 700 and 800oC for 20 h in 1 atm of N2/H2S/H2O-mixed gas in
order to characterize the high-temperature corrosion behavior of the
welded joint. Corrosion proceeded fast and almost linearly. It
increased with an increase in the corrosion temperature. H2S formed
FeS owing to sulfur released from H2S. The scales were fragile and
nonadherent.
Abstract: The rapid growth of the human population and the
environmental degradation associated with increased consumption of
resources raises concerns on sustainability. Social sustainability
constitutes one of the three dimensions of sustainability together with
environmental and economic dimensions. Even though there is not an
agreement on what social sustainability consists of, it is a well known
fact that it necessitates user participation. The fore, this study aims to
observe and analyze the role of user participation on social
sustainability. In this paper, the links between user participation and indicators of
social sustainability have been searched. In order to achieve this, first
of all a literature review on social sustainability has been done;
accordingly, the information obtained from researches has been used
in the evaluation of the projects conducted in the developing
countries considering user participation. These examples are taken as
role models with pros and cons for the development of the checklist
for the evaluation of the case studies. Furthermore, a case study over
the post earthquake residential settlements in Turkey have been
conducted. The case study projects are selected considering different building
scales (differing number of residential units), scale of the problem
(post-earthquake settlements, rehabilitation of shanty dwellings) and
the variety of users (differing socio-economic dimensions). Decisionmaking,
design, building and usage processes of the selected projects
and actors of these processes have been investigated in the context of
social sustainability. The cases include: New Gourna Village by
Hassan Fathy, Quinta Monroy dwelling units conducted in Chile by
Alejandro Aravena and Beyköy and Beriköy projects in Turkey
aiming to solve the problem of housing which have appeared after the
earthquake happened in 1999 have been investigated. Results of the
study possible links between social sustainability indicators and user
participation and links between user participation and the
peculiarities of place. Results are compared and discussed in order to find possible
solutions to form social sustainability through user participation.
Results show that social sustainability issues depend on communities'
characteristics, socio-economic conditions and user profile but user
participation has positive effects on some social sustainability
indicators like user satisfaction, a sense of belonging and social
stability.
Abstract: The combination of multi–walled carbon nanotubes
(MWCNTs) with polymers offers an attractive route to reinforce the
macromolecular compounds as well as the introduction of new
properties based on morphological modifications or electronic
interactions between the two constituents. As they are only a few
nanometers in dimension, it offers ultra-large interfacial area per
volume between the nano-element and polymer matrix. Nevertheless,
the use of MWCNTs as a rough material in different applications has
been largely limited by their poor processability, insolubility, and
infusibility. Studies concerning the nanofiller reinforced polymer
composites are justified in an attempt to overcome these limitations.
This work presents one preliminary study of MWCNTs dispersion
into the PVDF homopolymer. For preparation, the composite
components were diluted in n,n-dimethylacetamide (DMAc) with
mechanical agitation assistance. After complete dilution, followed by
slow evaporation of the solvent at 60°C, the samples were dried.
Films of about 80 μm were obtained. FTIR and UV-Vis
spectroscopic techniques were used to characterize the
nanocomposites. The appearance of absorption bands in the FTIR
spectra of nanofilled samples, when compared to the spectrum of
pristine PVDF samples, are discussed and compared with the UV-Vis
measurements.
Abstract: This paper analyzes the institutionalization of social
protest in Spain. In the current crisis Podemos party seems to
represent the political positions of the most affected citizens by the
economic situation. It studies using quantitative techniques (statistical
bivariate analysis), focusing on the exploitation of several bases of
statistics data from the Center for Sociological and Research of
Spanish Government, 15M movement characterization to its
institutionalization in the Podemos party. Making a comparison
between the participant's profile by the 15M and the social bases of
Podemos votes. Data on the transformation of the socio-demographic
profile of the fans, connoisseurs and 15M participants and voters are
given.
Abstract: Centrifugal-casting machine is used in manufacturing
special machine components like multi-layer journal bearing used in
all internal combustion engine, steam, gas turbine and air craft turboengine
where isotropic properties and high precisions are desired.
Moreover, this machine can be used in manufacturing thin wall hightech
machine components like cylinder liners and piston rings of IC
engine and other machine parts like sleeves, and bushes. Heavy-duty
machine component like railway wheel can also be prepared by
centrifugal casting. A lot of technological developments are required
in casting process for production of good casted machine body and
machine parts. Usually defects like blowholes, surface roughness,
chilled surface etc. are found in sand casted machine parts. But these
can be removed by centrifugal casting machine using rotating
metallic die. Moreover, die rotation, its temperature control, and good
pouring practice can contribute to the quality of casting because of
the fact that the soundness of a casting in large part depends upon
how the metal enters into the mold or dies and solidifies. Poor
pouring practice leads to variety of casting defects such as
temperature loss, low quality casting, excessive turbulence, over
pouring etc. Besides these, handling of molten metal is very
unsecured and dangerous for the workers. In order to get rid of all
these problems, the need of an automatic pouring device arises. In
this research work, a robot assisted pouring device and a centrifugal
casting machine are designed, developed constructed and tested
experimentally which are found to work satisfactorily. The robot
assisted pouring device is further modified and developed for using it
in actual metal casting process. Lot of settings and tests are required
to control the system and ultimately it can be used in automation of
centrifugal casting machine to produce high-tech machine parts with
desired precision.
Abstract: A composite material with carbon fiber and polymer
matrix has been used as adherent for manufacturing adhesive joints.
In order to evaluate different fiber orientations on joint performance,
the adherents with the 0°, ±15°, ±30°, ±45° fiber orientations were
used in the single lap joint configuration. The joints with an overlap
length of 25 mm were prepared according to the ASTM 1002
specifications and subjected to tensile loadings. The structural
adhesive used was a two-part epoxy to be cured at 70°C for an hour.
First, mechanical behaviors of the adherents were measured using
three point bending test. In the test, considerations were given to
stress to failure and elastic modulus. The results were compared with
theoretical ones using rule of mixture. Then, the joints were
manufactured in a specially prepared jig, after a proper surface
preparation. Experimental results showed that the fiber orientations
of the adherents affected the joint performance considerably; the
joints with ±45° adherents experienced the worst shear strength, half
of those with 0° adherents, and in general, there was a great
relationship between the fiber orientations and failure mechanisms.
Delamination problems were observed for many joints, which were
thought to be due to peel effects at the ends of the overlap. It was
proved that the surface preparation applied to the adherent surface
was adequate. For further explanation of the results, a numerical
work should be carried out using a possible non-linear analysis.
Abstract: This paper presents the strategic development plan of
winged rockets WIRES (WInged REusable Sounding rocket) aiming
at unmanned suborbital winged rocket for demonstrating future fully
reusable space transportation technologies, such as aerodynamics,
Navigation, Guidance and Control (NGC), composite structure,
propulsion system, and cryogenic tanks etc., by universities in
collaboration with government and industries, as well as the past and
current flight test results.
Abstract: Our purpose is to investigate how the relationship
between employees and innovation management processes can drive
organizations to successful innovations. This research is deeply
related to a new way of thinking about human resources management
practices. It’s not simply about improving the employees’
engagement, but rather about a different and more radical
commitment: the employee can take on the role traditionally played
by the customer, namely to become the first tester of an innovative
product or service, the first user/customer and eventually the first
investor in the innovation. This new perception of employees could
create the basis of a novelty in the innovation process where
innovation is taken to a next level when the problems with customer
driven innovation on the one hand, and employees driven innovation
on the other can be balanced. This research identifies an effective
approach to innovation where the employees will participate
throughout the whole innovation process, not only in the idea
creation but also in the idea definition and development by giving
feedback in parallel to that provided by customers and lead-users.
Abstract: Magnetic Resonance Imaging Contrast Agents
(MRI-CM) are significant in the clinical and biological imaging as
they have the ability to alter the normal tissue contrast, thereby
affecting the signal intensity to enhance the visibility and detectability
of images. Superparamagnetic Iron Oxide (SPIO) nanoparticles,
coated with dextran or carboxydextran are currently available for
clinical MR imaging of the liver. Most SPIO contrast agents are
T2 shortening agents and Resovist (Ferucarbotran) is one of a
clinically tested, organ-specific, SPIO agent which has a low
molecular carboxydextran coating. The enhancement effect of
Resovist depends on its relaxivity which in turn depends on factors
like magnetic field strength, concentrations, nanoparticle properties,
pH and temperature. Therefore, this study was conducted to
investigate the impact of field strength and different contrast
concentrations on enhancement effects of Resovist. The study
explored the MRI signal intensity of Resovist in the physiological
range of plasma from T2-weighted spin echo sequence at three
magnetic field strengths: 0.47 T (r1=15, r2=101), 1.5 T (r1=7.4,
r2=95), and 3 T (r1=3.3, r2=160) and the range of contrast
concentrations by a mathematical simulation. Relaxivities of r1 and r2
(L mmol-1 Sec-1) were obtained from a previous study and the selected
concentrations were 0.05, 0.06, 0.07, 0.08, 0.09, 0.1, 0.2, 0.3, 0.4, 0.5,
0.6, 0.7, 0.8, 0.9, 1.0, 2.0, and 3.0 mmol/L. T2-weighted images were
simulated using TR/TE ratio as 2000 ms /100 ms. According to the
reference literature, with increasing magnetic field strengths, the
r1 relaxivity tends to decrease while the r2 did not show any
systematic relationship with the selected field strengths. In parallel,
this study results revealed that the signal intensity of Resovist at lower
concentrations tends to increase than the higher concentrations. The
highest reported signal intensity was observed in the low field strength
of 0.47 T. The maximum signal intensities for 0.47 T, 1.5 T and 3 T
were found at the concentration levels of 0.05, 0.06 and 0.05 mmol/L,
respectively. Furthermore, it was revealed that, the concentrations
higher than the above, the signal intensity was decreased
exponentially. An inverse relationship can be found between the field
strength and T2 relaxation time, whereas, the field strength was
increased, T2 relaxation time was decreased accordingly. However,
resulted T2 relaxation time was not significantly different between
0.47 T and 1.5 T in this study. Moreover, a linear correlation of
transverse relaxation rates (1/T2, s–1) with the concentrations of
Resovist can be observed. According to these results, it can conclude
that the concentration of SPIO nanoparticle contrast agents and the
field strengths of MRI are two important parameters which can affect the signal intensity of T2-weighted SE sequence. Therefore, when MR
imaging those two parameters should be considered prudently.
Abstract: This paper proposes a method of learning topics for
broadcasting contents. There are two kinds of texts related to
broadcasting contents. One is a broadcasting script, which is a series of
texts including directions and dialogues. The other is blogposts, which
possesses relatively abstracted contents, stories, and diverse
information of broadcasting contents. Although two texts range over
similar broadcasting contents, words in blogposts and broadcasting
script are different. When unseen words appear, it needs a method to
reflect to existing topic. In this paper, we introduce a semantic
vocabulary expansion method to reflect unseen words. We expand
topics of the broadcasting script by incorporating the words in
blogposts. Each word in blogposts is added to the most semantically
correlated topics. We use word2vec to get the semantic correlation
between words in blogposts and topics of scripts. The vocabularies of
topics are updated and then posterior inference is performed to
rearrange the topics. In experiments, we verified that the proposed
method can discover more salient topics for broadcasting contents.
Abstract: Motion response of floating structures is of great
concern in marine engineering. Nonlinearity is an inherent property
of any floating bodies subjected to irregular waves. These floating
structures are continuously subjected to environmental loadings from
wave, current, wind etc. This can result in undesirable motions of the
vessel which may challenge the operability. For a floating body to
remain in its position, it should be able to induce a restoring force
when displaced. Mooring is provided to enable this restoring force.
This paper discusses the hydrodynamic performance and motion
characteristics of an 8 point spread mooring system applied to a pipe
laying barge operating in the West African sea. The modelling of the
barge is done using a computer aided-design (CAD) software
RHINOCEROS. Irregular waves are generated using a suitable wave
spectrum. Both frequency domain and time domain analysis is done.
Numerical simulations based on potential theory are carried out to
find the responses and hydrodynamic performance of the barge in
both free floating as well as moored conditions. Initially, potential
flow frequency domain analysis is done to obtain the Response
Amplitude Operator (RAO) which gives an idea about the structural
motion in free floating state. RAOs for different wave headings are
analyzed. In the following step, a time domain analysis is carried out
to obtain the responses of the structure in the moored condition. In
this study, wave induced motions are only taken into consideration.
Wind and current loads are ruled out and shall be included in further
studies. For the current study, 2000 seconds simulation is taken. The
results represent wave induced motion responses, mooring line
tensions and identify critical mooring lines.
Abstract: A combined heat and power (CHP) system is an efficient and clean way to generate power (electricity). Heat produced by the CHP system can be used for water and space heating. The CHP system which uses hydrogen as fuel produces zero carbon emission. Its’ efficiency can reach more than 80% whereas that of a traditional power station can only reach up to 50% because much of the thermal energy is wasted. The other advantages of CHP systems include that they can decentralize energy generation, improve energy security and sustainability, and significantly reduce the energy cost to the users. This paper presents the economic benefits of using a CHP system in the domestic environment. For this analysis, natural gas is considered as potential fuel as the hydrogen fuel cell based CHP systems are rarely used. UK government incentives for CHP systems are also considered as the added benefit. Results show that CHP requires a significant initial investment in returns it can reduce the annual energy bill significantly. Results show that an investment may be paid back in 7 years. After the back period, CHP can run for about 3 years as most of the CHP manufacturers provide 10 year warranty.
Abstract: The paper presents an additive manufacturing process for the production of metal and composite parts. It is termed as composite metal foil manufacturing and is a combination of laminated object manufacturing and brazing techniques. The process has been described in detail and is being used to produce dissimilar aluminum to copper foil single lap joints. A three dimensional finite element model has been developed to study the thermo-mechanical characteristics of the dissimilar Al/Cu single lap joint. The effects of thermal stress and strain have been analyzed by carrying out transient thermal analysis on the heated plates used to join the two 0.1mm thin metal foils. Tensile test has been carried out on the foils before joining and after the single Al/Cu lap joints are made, they are subjected to tensile lap-shear test to analyze the effect of heat on the foils. The analyses are designed to assess the mechanical integrity of the foils after the brazing process and understand whether or not the heat treatment has an effect on the fracture modes of the produced specimens.
Abstract: This paper explored the challenges faced by the
management of a Ghanaian state enterprise in managing conflicts and
disturbances associated with its attempt to implement new work
practices to enhance its capability to operate as a commercial entity.
The purpose was to understand the extent to which organizational
involvement, consistency and adaptability influence employees’
consumption of new work practices in transforming the
organization’s organizational activity system. Using selfadministered
questionnaires, data were collected from one hundred
and eighty (180) employees and analyzed using both descriptive and
inferential statistics. The results showed that constraints in
organizational involvement and adaptability prevented the positive
consumption of new work practices by employees in the
organization. It is also found that the organization’s employees failed
to consume the new practices being implemented, because they
perceived the process as non-involving, and as such, did not
encourage the development of employee capability, empowerment,
and teamwork. The study concluded that the failure of the
organization’s management to create opportunities for organizational
learning constrained its ability to get employees consume the new
work practices, which situation could have facilitated the
organization’s capabilities of operating as a commercial entity.
Abstract: The early-stage damage detection in offshore
structures requires continuous structural health monitoring and for the
large area the position of sensors will also plays an important role in
the efficient damage detection. Determining the dynamic behavior of
offshore structures requires dense deployment of sensors. The wired
Structural Health Monitoring (SHM) systems are highly expensive
and always needs larger installation space to deploy. Wireless sensor
networks can enhance the SHM system by deployment of scalable
sensor network, which consumes lesser space. This paper presents the
results of wireless sensor network based Structural Health Monitoring
method applied to a scaled experimental model of offshore structure
that underwent wave loading. This method determines the
serviceability of the offshore structure which is subjected to various
environment loads. Wired and wireless sensors were installed in the
model and the response of the scaled BLSRP model under wave
loading was recorded. The wireless system discussed in this study is
the Raspberry pi board with Arm V6 processor which is programmed
to transmit the data acquired by the sensor to the server using Wi-Fi
adapter, the data is then hosted in the webpage. The data acquired
from the wireless and wired SHM systems were compared and the
design of the wireless system is verified.
Abstract: The focus of this study was to determine the factors associated with the use of substances for sport performance of youth in Lagos state sport. Questionnaire was the instrument used for the study. Descriptive research method was used. The estimated population for the study was 2000 sport men and women. The sample size was 200 respondents for purposive sampling techniques were used. The instrument was validated in it content and constructs value. The instrument was administered with the assistance of the coaches. Same 200 copies administered were returned. The data obtained was analysed using simple percentage and chi-square (x2) for stated hypothesis at 0.05 level of significance. The finding reveal that sport injuries exercise induced and anaphylaxis and asthma and feeling of loss of efficacy associated with alcohol used on sport performance among the users of substances. Alcohol users are recommended to partake in sport like swimming, basketball and volleyball because they have space of time for resting while at play. Government should be fully in charge of the health of sport men and women.
Abstract: Low density polyethylene (LDPE) nanocomposites
with 3, 5 and 7 wt. % cobalt ferrite (CoFe2O4) nanopowder fabricated
with extrusion mixing and followed up by hot press to reach compact
samples. The transmission/reflection measurements were carried out
with a network analyzer in the frequency range of 8-12 GHz. By
increasing the percent of CoFe2O4 nanopowder, reflection loss (S11)
increases, while transferring loss (S21) decreases. Reflectivity (R)
calculations made using S11 and S21. Increase in percent of CoFe2O4
nanopowder up to 7 wt. % in composite leaded to higher reflectivity
amount, and revealed that increasing the percent of CoFe2O4
nanopowder up to 7 wt. % leads to further microwave absorption in
8-12 GHz range.
Abstract: In this paper, an attempt has been made for the design
of a robotic library using an intelligent system. The robot works on
the ARM microprocessor, motor driver circuit with 5 degrees of
freedom with Wi-Fi and GPS based communication protocol. The
authenticity of the library books is controlled by RFID. The proposed
robotic library system is facilitated with embedded system and ARM.
In this library issuance system, the previous potential readers’
authentic review reports have been taken into consideration for
recommending suitable books to the deserving new users and the
issuance of books or periodicals is based on the users’ decision. We
have conjectured that the Wi-Fi based robotic library management
system would allow fast transaction of books issuance and it also
produces quality readers.
Abstract: Currently, there are few user friendly Weigh-in-
Motion (WIM) data analysis softwares available which can produce
traffic input data for the recently developed AASHTOWare pavement
Mechanistic-Empirical (ME) design software. However, these
softwares have only rudimentary Quality Control (QC) processes.
Therefore, they cannot properly deal with erroneous WIM data. As
the pavement performance is highly sensible to the quality of WIM
data, it is highly recommended to use more refined QC process on
raw WIM data to get a good result. This study develops a userfriendly
software, which can produce traffic input for the ME design
software. This software takes the raw data (Class and Weight data)
collected from the WIM station and processes it with a sophisticated
QC procedure. Traffic data such as traffic volume, traffic distribution,
axle load spectra, etc. can be obtained from this software; which can
directly be used in the ME design software.