Abstract: Composite pins of rubber dust collected from tyre
retreading centres of trucks, cars and buses etc.and epoxy with
weight percentages of 10. 15, and 20 % of rubber (weight fractions of
9, 13 and 17 % respectively) have been prepared in house with the
help of a split wooden mould. The pins were tested in a pin-on-disc
wear monitor to determine the co-efficient of friction and weight
losses with varying speeds, loads and time. The wear volume and
wear rates have also been found out for all these three specimens.. It
is observed that all the specimens have exhibited very low coefficient
of friction and low wear rates under dry sliding condition. Out of the
above three samples tested, the specimen with 10 % rubber dust by
weight has shown lowest wear rates. However a peculiar result i.e
decreasing trend has been obtained with 20% reinforcement of rubber
in epoxy while rubbed against steel at varying speeds. This might
have occurred due to high surface finish of the disc and formation of
a thin transfer layer from the composite
Abstract: The purpose of this paper is to assess the value of neural networks for classification of cancer and noncancer prostate cells. Gauss Markov Random Fields, Fourier entropy and wavelet average deviation features are calculated from 80 noncancer and 80 cancer prostate cell nuclei. For classification, artificial neural network techniques which are multilayer perceptron, radial basis function and learning vector quantization are used. Two methods are utilized for multilayer perceptron. First method has single hidden layer and between 3-15 nodes, second method has two hidden layer and each layer has between 3-15 nodes. Overall classification rate of 86.88% is achieved.
Abstract: Preparation of size controlled nano-particles of silver catalyst on carbon substrate from e-waste has been investigated. Chemical route was developed by extraction of the metals available in nitric acid followed by treatment with hydrofluoric acid. Silver metal particles deposited with an average size 4-10 nm. A stabilizer concentration of 10- 40 g/l was used. The average size of the prepared silver decreased with increase of the anode current density. Size uniformity of the silver nano-particles was improved distinctly at higher current density no more than 20mA... Grain size increased with EK time whereby aggregation of particles was observed after 6 h of reaction.. The chemical method involves adsorption of silver nitrate on the carbon substrate. Adsorbed silver ions were directly reduced to metal particles using hydrazine hydrate. Another alternative method is by treatment with ammonia followed by heating the carbon loaded-silver hydroxide at 980°C. The product was characterized with the help of XRD, XRF, ICP, SEM and TEM techniques.
Abstract: The “conveyor belt" as a product represents a
complex high performance component with a wide range of different
applications. Further development of these highly complex
components demands an integration of new technologies and new
enhanced materials. In this context nanostructured fillers appear to
have a more promising effect on the performance of the conveyor
belt composite than conventional micro-scaled fillers.
Within the project “DotTrans" nanostructured fillers, for example
silicon dioxide, are used to optimize performance parameters of
conveyor belt systems. The objective of the project includes
operating parameters like energy consumption or friction
characteristics as well as adaptive parameters like cut or wear
resistance.
Abstract: It has been defined that the “network is the system".
This implies providing levels of service, reliability, predictability and
availability that are commensurate with or better than those that
individual computers provide today. To provide this requires
integrated network management for interconnected networks of
heterogeneous devices covering both the local campus. In this paper
we are addressing a framework to effectively deal with this issue. It
consists of components and interactions between them which are
required to perform the service fault management. A real-world
scenario is used to derive the requirements which have been applied
to the component identification. An analysis of existing frameworks
and approaches with respect to their applicability to the framework is
also carried out.
Abstract: Face and facial expressions play essential roles in
interpersonal communication. Most of the current works on the facial
expression recognition attempt to recognize a small set of the
prototypic expressions such as happy, surprise, anger, sad, disgust
and fear. However the most of the human emotions are
communicated by changes in one or two of discrete features. In this
paper, we develop a facial expressions synthesis system, based on the
facial characteristic points (FCP's) tracking in the frontal image
sequences. Selected FCP's are automatically tracked using a crosscorrelation
based optical flow. The proposed synthesis system uses a
simple deformable facial features model with a few set of control
points that can be tracked in original facial image sequences.
Abstract: In this paper, the effect of receive and/or transmit
antenna spacing on the performance (BER vs. SNR) of multipleantenna
systems is determined by using an RCS (Radar Cross
Section) channel model. In this physical model, the scatterers
existing in the propagation environment are modeled by their RCS so
that the correlation of the receive signal complex amplitudes, i.e.,
both magnitude and phase, can be estimated. The proposed RCS
channel model is then compared with classical models.
Abstract: For lack of the visualization of the ultrasonic detection
method of partial discharge (PD), the ultrasonic detection technology
combined with the X-ray visual detection method (UXV) is proposed.
The method can conduct qualitative analysis accurately and conduct
reliable positioning diagnosis to the internal insulation defects of
GIS, and while it could make up the blindness of the X-ray visual
detection method and improve the detection rate. In this paper, an
experimental model of GIS is used as the trial platform, a variety of
insulation defects are set inside the GIS cavity. With the proposed
method, the ultrasonic method is used to conduct the preliminary
detection, and then the X-ray visual detection is used to locate and
diagnose precisely. Therefore, the proposed UXV technology is
feasible and practical.
Abstract: Artificial Intelligence based gaming is an interesting topic in the state-of-art technology. This paper presents an automation of a tradition Omani game, called Al-Hawalees. Its related issues are resolved and implemented using artificial intelligence approach. An AI approach called mini-max procedure is incorporated to make a diverse budges of the on-line gaming. If number of moves increase, time complexity will be increased in terms of propositionally. In order to tackle the time and space complexities, we have employed a back propagation neural network (BPNN) to train in off-line to make a decision for resources required to fulfill the automation of the game. We have utilized Leverberg- Marquardt training in order to get the rapid response during the gaming. A set of optimal moves is determined by the on-line back propagation training fashioned with alpha-beta pruning. The results and analyses reveal that the proposed scheme will be easily incorporated in the on-line scenario with one player against the system.
Abstract: The presented work is motivated by a French law
regarding nuclear waste management. A new conceptual Accelerator
Driven System (ADS) designed for the Minor Actinides (MA)
transmutation has been assessed by numerical simulation. The
MUltiple Spallation Target (MUST) ADS combines high thermal power (up to 1.4 GWth) and high specific power. A 30 mA and 1
GeV proton beam is divided into three secondary beams transmitted on three liquid lead-bismuth spallation targets. Neutron and thermalhydraulic
simulations have been performed with the code MURE, based on the Monte-Carlo transport code MCNPX. A methodology has been developed to define characteristic of the MUST ADS concept according to a specific transmutation scenario. The reference
scenario is based on a MA flux (neptunium, americium and curium)
providing from European Fast Reactor (EPR) and a plutonium multireprocessing
strategy is accounted for. The MUST ADS reference
concept is a sodium cooled fast reactor. The MA fuel at equilibrium is mixed with MgO inert matrix to limit the core reactivity and
improve the fuel thermal conductivity. The fuel is irradiated over five
years. Five years of cooling and two years for the fuel fabrication are
taken into account. The MUST ADS reference concept burns about 50% of the initial MA inventory during a complete cycle. In term of
mass, up to 570 kg/year are transmuted in one concept. The methodology to design the MUST ADS and to calculate fuel
composition at equilibrium is precisely described in the paper. A detailed fuel evolution analysis is performed and the reference scenario is compared to a scenario where only americium transmutation is performed.
Abstract: Springback is a significant problem in the sheet metal
forming process. When the tools are released after the stage of
forming, the product springs out, because of the action of the internal
stresses. In many cases the deviation of form is too large and the
compensation of the springback is necessary. The precise prediction
of the springback of product is increasingly significant for the design
of the tools and for compensation because of the higher ratio of the
yield stress to the elastic modulus.
The main object in this paper was to study the effect of the
anisotropy on the springback for three directions of rolling: 0°, 45°
and 90°. At the same time, we highlighted the influence of three
different metallic materials: Aluminum, Steel and Galvanized steel.
The original of our purpose consist on tests which are ensured by
adapting a U-type stretching-bending device on a tensile testing
machine, where we studied and quantified the variation of the
springback according to the direction of rolling. We also showed the
role of lubrication in the reduction of the springback.
Moreover, in this work, we have studied important characteristics
in deep drawing process which is a springback. We have presented
defaults that are showed in this process and many parameters
influenced a springback.
Finally, our results works lead us to understand the influence of
grains orientation with different metallic materials on the springback
and drawing some conclusions how to concept deep drawing tools. In
addition, the conducted work represents a fundamental contribution
in the discussion the industry application.
Abstract: At present, it is very common to find renewable
energy resources, especially wind power, connected to distribution
systems. The impact of this wind power on voltage distribution levels
has been addressed in the literature. The majority of this works deals
with the determination of the maximum active and reactive power
that is possible to be connected on a system load bus, until the
voltage at that bus reaches the voltage collapse point. It is done by the
traditional methods of PV curves reported in many references.
Theoretical expression of maximum power limited by voltage
stability transfer through a grid is formulated using an exact
representation of distribution line with ABCD parameters. The
expression is used to plot PV curves at various power factors of a
radial system. Limited values of reactive power can be obtained. This
paper presents a method to study the relationship between the active
power and voltage (PV) at the load bus to identify the voltage
stability limit. It is a foundation to build a permitted working
operation region in complying with the voltage stability limit at the
point of common coupling (PCC) connected wind farm.
Abstract: Traditionally, Internet has provided best-effort service to every user regardless of its requirements. However, as Internet becomes universally available, users demand more bandwidth and applications require more and more resources, and interest has developed in having the Internet provide some degree of Quality of Service. Although QoS is an important issue, the question of how it will be brought into the Internet has not been solved yet. Researches, due to the rapid advances in technology are proposing new and more desirable capabilities for the next generation of IP infrastructures. But neither all applications demand the same amount of resources, nor all users are service providers. In this way, this paper is the first of a series of papers that presents an architecture as a first step to the optimization of QoS in the Internet environment as a solution to a SMSE's problem whose objective is to provide public service to internet with certain Quality of Service expectations. The service provides new business opportunities, but also presents new challenges. We have designed and implemented a scalable service framework that supports adaptive bandwidth based on user demands, and the billing based on usage and on QoS. The developed application has been evaluated and the results show that traffic limiting works at optimum and so it does exceeding bandwidth distribution. However, some considerations are done and currently research is under way in two basic areas: (i) development and testing new transfer protocols, and (ii) developing new strategies for traffic improvements based on service differentiation.
Abstract: Multi-Radio Multi-Channel Wireless Mesh Networks (MRMC-WMNs) operate at the backbone to access and route high volumes of traffic simultaneously. Such roles demand high network capacity, and long “online" time at the expense of accelerated transmission energy depletion and poor connectivity. This is the problem of transmission power control. Numerous power control methods for wireless networks are in literature. However, contributions towards MRMC configurations still face many challenges worth considering. In this paper, an energy-efficient power selection protocol called PMMUP is suggested at the Link-Layer. This protocol first divides the MRMC-WMN into a set of unified channel graphs (UCGs). A UCG consists of multiple radios interconnected to each other via a common wireless channel. In each UCG, a stochastic linear quadratic cost function is formulated. Each user minimizes this cost function consisting of trade-off between the size of unification states and the control action. Unification state variables come from independent UCGs and higher layers of the protocol stack. The PMMUP coordinates power optimizations at the network interface cards (NICs) of wireless mesh routers. The proposed PMMUP based algorithm converges fast analytically with a linear rate. Performance evaluations through simulations confirm the efficacy of the proposed dynamic power control.
Abstract: This paper presents a new problem solving approach
that is able to generate optimal policy solution for finite-state
stochastic sequential decision-making problems with high data
efficiency. The proposed algorithm iteratively builds and improves
an approximate Markov Decision Process (MDP) model along with
cost-to-go value approximates by generating finite length trajectories
through the state-space. The approach creates a synergy between an
approximate evolving model and approximate cost-to-go values to
produce a sequence of improving policies finally converging to the
optimal policy through an intelligent and structured search of the
policy space. The approach modifies the policy update step of the
policy iteration so as to result in a speedy and stable convergence to
the optimal policy. We apply the algorithm to a non-holonomic
mobile robot control problem and compare its performance with
other Reinforcement Learning (RL) approaches, e.g., a) Q-learning,
b) Watkins Q(λ), c) SARSA(λ).
Abstract: Researches show that probability-statistical methods application, especially at the early stage of the aviation Gas Turbine Engine (GTE) technical condition diagnosing, when the flight information has property of the fuzzy, limitation and uncertainty is unfounded. Hence the efficiency of application of new technology Soft Computing at these diagnosing stages with the using of the Fuzzy Logic and Neural Networks methods is considered. According to the purpose of this problem training with high accuracy of fuzzy multiple linear and non-linear models (fuzzy regression equations) which received on the statistical fuzzy data basis is made. For GTE technical condition more adequate model making dynamics of skewness and kurtosis coefficients- changes are analysed. Researches of skewness and kurtosis coefficients values- changes show that, distributions of GTE work parameters have fuzzy character. Hence consideration of fuzzy skewness and kurtosis coefficients is expedient. Investigation of the basic characteristics changes- dynamics of GTE work parameters allows drawing conclusion on necessity of the Fuzzy Statistical Analysis at preliminary identification of the engines' technical condition. Researches of correlation coefficients values- changes shows also on their fuzzy character. Therefore for models choice the application of the Fuzzy Correlation Analysis results is offered. At the information sufficiency is offered to use recurrent algorithm of aviation GTE technical condition identification (Hard Computing technology is used) on measurements of input and output parameters of the multiple linear and non-linear generalised models at presence of noise measured (the new recursive Least Squares Method (LSM)). The developed GTE condition monitoring system provides stageby- stage estimation of engine technical conditions. As application of the given technique the estimation of the new operating aviation engine technical condition was made.
Abstract: Isobaric vapor-liquid equilibrium measurements are reported for the binary mixtures of n-Butylamine and Triethylamine with Cumene at 97.3 kPa. The measurements have been performed using a vapor recirculating type (modified Othmer's) equilibrium still. The binary mixture of n-Butylamine + Cumene shows positive deviation from ideality. Triethylamine + Cumene mixture shows negligible deviation from ideality. None of the systems form an azeotrope. The activity coefficients have been calculated taking into consideration the vapor phase nonideality. The data satisfy the thermodynamic consistency test of Herington. The activity coefficients have been satisfactorily correlated by means of the Margules, NRTL, and Black equations. The activity coefficient values obtained by the UNIFAC model are also reported.
Abstract: Sedimentation process resulting from soil erosion in
the water basin especially in arid and semi-arid where poor
vegetation cover in the slope of the mountains upstream could
contribute to sediment formation. The consequence of sedimentation
not only makes considerable change in the morphology of the river
and the hydraulic characteristics but would also have a major
challenge for the operation and maintenance of the canal network
which depend on water flow to meet the stakeholder-s requirements.
For this reason mathematical modeling can be used to simulate the
effective factors on scouring, sediment transport and their settling
along the waterways. This is particularly important behind the
reservoirs which enable the operators to estimate the useful life of
these hydraulic structures. The aim of this paper is to simulate the
sedimentation and erosion in the eastern and western water intake
structures of the Dez Diversion weir using GSTARS-3 software. This
is done to estimate the sedimentation and investigate the ways in
which to optimize the process and minimize the operational
problems. Results indicated that the at the furthest point upstream of
the diversion weir, the coarser sediment grains tended to settle. The
reason for this is the construction of the phantom bridge and the
outstanding rocks just upstream of the structure. The construction of
these along the river course has reduced the momentum energy
require to push the sediment loads and make it possible for them to
settle wherever the river regime allows it. Results further indicated a
trend for the sediment size in such a way that as the focus of study
shifts downstream the size of grains get smaller and vice versa. It
was also found that the finding of the GSTARS-3 had a close
proximity with the sets of the observed data. This suggests that the
software is a powerful analytical tool which can be applied in the
river engineering project with a minimum of costs and relatively
accurate results.
Abstract: The quality of short term load forecasting can improve the efficiency of planning and operation of electric utilities. Artificial Neural Networks (ANNs) are employed for nonlinear short term load forecasting owing to their powerful nonlinear mapping capabilities. At present, there is no systematic methodology for optimal design and training of an artificial neural network. One has often to resort to the trial and error approach. This paper describes the process of developing three layer feed-forward large neural networks for short-term load forecasting and then presents a heuristic search algorithm for performing an important task of this process, i.e. optimal networks structure design. Particle Swarm Optimization (PSO) is used to develop the optimum large neural network structure and connecting weights for one-day ahead electric load forecasting problem. PSO is a novel random optimization method based on swarm intelligence, which has more powerful ability of global optimization. Employing PSO algorithms on the design and training of ANNs allows the ANN architecture and parameters to be easily optimized. The proposed method is applied to STLF of the local utility. Data are clustered due to the differences in their characteristics. Special days are extracted from the normal training sets and handled separately. In this way, a solution is provided for all load types, including working days and weekends and special days. The experimental results show that the proposed method optimized by PSO can quicken the learning speed of the network and improve the forecasting precision compared with the conventional Back Propagation (BP) method. Moreover, it is not only simple to calculate, but also practical and effective. Also, it provides a greater degree of accuracy in many cases and gives lower percent errors all the time for STLF problem compared to BP method. Thus, it can be applied to automatically design an optimal load forecaster based on historical data.
Abstract: Gastric ulceration is a discontinuity in gastric mucosa, usually occurs due to imbalance between the gastric mucosal protective factors, that is called gastric mucosal barrier, and the aggressive factors, to which the mucosa is exposed. This study was carried out on sixty male Sprague-Dowely rats (12- 16 weeks old) allocated into two groups. The first control group and the second Gastric lesion group which induced by oral administration of a single daily dose of aspirin at a dose of 300 mg/kg body weight for 7 consecutive-days (6% aspirin solution will be prepared and each rat will be given 5 ml of that solution/kg body weight). Blood is collected 1, 2 and 3 weeks after induction of gastric ulceration. Significant increase in serum copper, nitric oxide, and prostaglandin E2 all over the period of experiment. Significant decrease in erythrocyte superoxide dismutase (t-SOD) activities, serum (calcium, phosphorus, glucose and insulin) levels. Non-significant changes in serum sodium and potassium levels are obtained.