Abstract: Mercury is a natural occurring element and present in
various concentrations in the environment. Due to its toxic effects, it
is desirable to research mercury sensitive materials to adsorb
mercury. This paper describes the preparation of Au nanoparticles for
mercury adsorption by using a microwave (MW)-polyol method in
the presence of three different Sodium Chloride (NaCl)
concentrations (10, 20 and 30 mM). Mixtures of spherical, triangular,
octahedral, decahedral particles and 1-D product were obtained using
this rapid method. Sizes and shapes was found strongly depend on the
concentrations of NaCl. Without NaCl concentration, spherical,
triangular plates, octahedral, decahedral nanoparticles and 1D
product were produced. At the lower NaCl concentration (10 mM),
spherical, octahedral and decahedral nanoparticles were present,
while spherical and decahedral nanoparticles were preferentially form
by using 20 mM of NaCl concentration. Spherical, triangular plates,
octahedral and decahedral nanoparticles were obtained at the highest
NaCl concentration (30 mM). The amount of mercury adsorbed using
20 ppm mercury solution is the highest (67.5 %) for NaCl
concentration of 30 mM. The high yield of polygonal particles will
increase the mercury adsorption. In addition, the adsorption of
mercury is also due to the sizes of the particles. The sizes of particles
become smaller with increasing NaCl concentrations (size ranges, 5-
16 nm) than those synthesized without addition of NaCl (size ranges
11-32 nm). It is concluded that NaCl concentrations affects the
formation of sizes and shapes of Au nanoparticles thus affects the
mercury adsorption.
Abstract: In recent years application of natural antimicrobials
instead of conventional ones, due to their hazardous effects on health,
has got serious attentions. On the basis of the results of different
studies, chitosan, a natural bio-degradable and non-toxic
biopolysaccharide derived from chitin, has potential to be used as a
natural antimicrobial. Chitosan has exhibited high antimicrobial
activity against a wide variety of pathogenic and spoilage
microorganisms, including fungi, and Gram-positive and Gramnegative
bacteria. The antimicrobial action is influenced by intrinsic
factors such as the type of chitosan, the degree of chitosan
polymerization and extrinsic factors such as the microbial organism,
the environmental conditions and presence of the other components.
The use of chitosan in food systems should be based on sufficient
knowledge of the complex mechanisms of its antimicrobial mode of
action. In this article we review a number of studies on the
investigation of chitosan antimicrobial properties and application of
them in culture and food mediums.
Abstract: A device analysis of the photoconductive
semiconductor switch is carried out to investigate distribution of
electric field and carrier concentrations as well as the current density
distribution. The operation of this device was then investigated as a
switch operating in X band. It is shown that despite the presence of
symmetry geometry, switch current density of the on-state steady
state mode is distributed asymmetrically throughout the device.
Abstract: Silver nanoparticles were prepared by chemical reduction method. Silver nitrate was taken as the metal precursor and hydrazine hydrate as a reducing agent. The formation of the silver nanoparticles was monitored using UV-Vis absorption spectroscopy. The UV-Vis spectroscopy revealed the formation of silver nanopart├¡cles by exhibing the typical surface plasmon absorption maxima at 418-420 nm from the UV–Vis spectrum. Comparison of theoretical (Mie light scattering theory) and experimental results showed that diameter of silver nanoparticles in colloidal solution is about 60 nm. We have used energy-dispersive spectroscopy (EDX), X-ray diffraction (XRD), transmission electron microscopy (TEM) and, UV–Vis spectroscopy to characterize the nanoparticles obtained. The energy-dispersive spectroscopy (EDX) of the nanoparticles dispersion confirmed the presence of elemental silver signal no peaks of other impurity were detected. The average size and morphology of silver nanoparticles were determined by transmission electron microscopy (TEM). TEM photographs indicate that the nanopowders consist of well dispersed agglomerates of grains with a narrow size distribution (40 and 60 nm), whereas the radius of the individual particles are between 10 and 20 nm. The synthesized nanoparticles have been structurally characterized by X-ray diffraction and transmission high-energy electron diffraction (HEED). The peaks in the XRD pattern are in good agreement with the standard values of the face-centered-cubic form of metallic silver (ICCD-JCPDS card no. 4-0787) and no peaks of other impurity crystalline phases were detected. Additionally, the antibacterial activity of the nanopart├¡culas dispersion was measured by Kirby-Bauer method. The nanoparticles of silver showed high antimicrobial and bactericidal activity against gram positive bacteria such as Escherichia Coli, Pseudimonas aureginosa and staphylococcus aureus which is a highly methicillin resistant strain.
Abstract: In the current study, we have conducted an experimental investigation on the utilization of electronic arc furnace (EAF) reducing slag for the absorption of CO2 via wet grinding method. It was carried out by various grinding conditions. The slag was ground in the vibrating ball mill in the presence of CO2 and pure water under ambient temperature. The reaction behavior was monitored with constant pressure method, and the changes of experimental systems volume as a function of grinding time were measured. It was found that the CO2 absorption occurred as soon as the grinding started. The CO2 absorption was significantly increased in the case of wet grinding compare to the dry grinding. Generally, the amount of CO2 absorption increased as the amount of water, weight of slag and initial pressure increased. However, it was decreased when the amount of water exceeds 200ml and when smaller balls were used. The absorption of CO2 occurred simultaneously with the start of the grinding and it stopped when the grinding was stopped. According to this research, the CO2 reacted with the CaO inside the slag, forming CaCO3.
Abstract: In this study, the dispersion of heavy particles line in
an isotropic and incompressible three-dimensional turbulent flow has
been studied using the Kinematic Simulation techniques to find out
the evolution of the line fractal dimension. The fractal dimension of
the line is found in the case of different particle gravity (in practice,
different values of particle drift velocity) in the presence of small
particle inertia with a comparison with that obtained in the diffusion
case of material line at the same Reynolds number. It can be
concluded for the dispersion of heavy particles line in turbulent flow
that the particle gravity affect the fractal dimension of the line for
different particle gravity velocities in the range 0.2 < W < 2. With
the increase of the particle drift velocity, the fractal dimension of the
line decreases which may be explained as the particles pass many
scales in their journey in the direction of the gravity and the particles
trajectories do not affect by these scales at high particle drift
velocities.
Abstract: With the presence of a uniform vertical magnetic field and suspended particles, thermocapillary instability in a horizontal liquid layer is investigated. The resulting eigenvalue is solved by the Galerkin technique for various basic temperature gradients. It is found that the presence of magnetic field always has a stability effect of increasing the critical Marangoni number.
Abstract: EcoDam is an adenine-N6 DNA methyltransferase
that methylates the GATC sites in the Escherichia coli genome.
DNA-adenine methylation is not present in higher eukaryotes
including humans. These observations raise the possibility that dam
inhibitors may be used as anti-microbial agents. Polyphosphate
(Poly(P)) is an important metabolite and signaling molecule in
prokaryotes and eukaryotes. Here, by using gel retardation
experiments to investigate the competition of DNA binding by
EcoDam in the presence of polyphosphate, we found that Poly (P)
strongly interferes with DNA binding by EcoDam, while same
concentration of monophosphate does not. In addition, we
demonstrated that Poly (P) binding inhibits the activity of EcoDam
and our results suggest that Poly (P) led to strong inhibition of the
EcoDam catalytic activity, while monophosphate had only moderate
effect.
Abstract: Inventory decisional environment of short life-cycle
products is full of uncertainties arising from randomness and
fuzziness of input parameters like customer demand requiring
modeling under hybrid uncertainty. Prior inventory models
incorporating fuzzy demand have unfortunately ignored stochastic
variation of demand. This paper determines an unambiguous optimal
order quantity from a set of n fuzzy observations in a newsvendor
inventory setting in presence of fuzzy random variable demand
capturing both fuzzy perception and randomness of customer
demand. The stress of this paper is in providing solution procedure
that attains optimality in two steps with demand information
availability in linguistic phrases leading to fuzziness along with
stochastic variation. The first step of solution procedure identifies
and prefers one best fuzzy opinion out of all expert opinions and the
second step determines optimal order quantity from the selected
event that maximizes profit. The model and solution procedure is
illustrated with a numerical example.
Abstract: Unsteady magnetohydrodynamics (MHD) boundary
layer flow and heat transfer over a continuously stretching surface in
the presence of radiation is examined. By similarity transformation,
the governing partial differential equations are transformed to a set of
ordinary differential equations. Numerical solutions are obtained by
employing the Runge-Kutta-Fehlberg method scheme with shooting
technique in Maple software environment. The effects of
unsteadiness parameter, radiation parameter, magnetic parameter and
Prandtl number on the heat transfer characteristics are obtained and
discussed. It is found that the heat transfer rate at the surface
increases as the Prandtl number and unsteadiness parameter increase
but decreases with magnetic and radiation parameter.
Abstract: Gas hydrates form when a number of factors co-exist:
free water, hydrocarbon gas, cold temperatures and high pressures are typical of the near mud-line conditions in a deepwater drilling
operation. Subsequently, when drilling with water based muds, particularly on exploration wells, the risk of hydrate formation
associated with a gas influx is high. The consequences of gas hydrate
formation while drilling are severe, and as such, every effort should be made to ensure the risk of hydrate formation is either eliminated
or significantly reduced. Thermodynamic inhibitors are used to reduce the free water content of a drilling mud, and thus suppress the
hydrate formation temperature. Very little experimental work has
been performed by oil and gas research companies on the evaluation
of gas hydrate formation in a water-based drilling mud. The main
objective of this paper is to investigate the experimental gas hydrate
formation for a mixture of methane, carbon dioxide & nitrogen in a
water-based drilling mud with or without presence of different
concentrations of thermodynamic inhibitors including pure salt and a
combination of salt with methanol or ethylene glycol at different
concentrations in a static loop apparatus. The experiments were
performed using a static loop apparatus consisting of a 2.4307 cm
inside diameter and 800 cm long pipe. All experiments were conducted at 2200 psia. The temperature in the loop was decreased at
a rate of 3.33 °F/h from initial temperature of 80 °F.
Abstract: The conventional production of biodiesel from crude
palm oil which contains large amounts of free fatty acids in the
presence of a homogeneous base catalyst confronts the problems of
soap formation and very low yield of biodiesel. To overcome these
problems, free fatty acids must be esterified to their esters in the
presence of an acid catalyst prior to alkaline-catalyzed
transesterification. Sulfated metal oxides are a promising group of
catalysts due to their very high acidity. In this research, aluminadoped
sulfated tin oxide (SO4
2-/Al2O3-SnO2) catalysts were prepared
and used for esterification of free fatty acids in crude palm oil in a
batch reactor. The SO4
2-/Al2O3-SnO2 catalysts were prepared from
different Al precursors. The results showed that different Al
precursors gave different activities of the SO4
2-/Al2O3-SnO2 catalysts.
The esterification of free fatty acids in crude palm oil with methanol
in the presence of SO4
2-/Al2O3-SnO2 catalysts followed first-order
kinetics.
Abstract: In this paper is shown that the probability-statistic methods application, especially at the early stage of the aviation gas turbine engine (GTE) technical condition diagnosing, when the flight information has property of the fuzzy, limitation and uncertainty is unfounded. Hence is considered the efficiency of application of new technology Soft Computing at these diagnosing stages with the using of the Fuzzy Logic and Neural Networks methods. Training with high accuracy of fuzzy multiple linear and non-linear models (fuzzy regression equations) which received on the statistical fuzzy data basis is made. Thus for GTE technical condition more adequate model making are analysed dynamics of skewness and kurtosis coefficients' changes. Researches of skewness and kurtosis coefficients values- changes show that, distributions of GTE work parameters have fuzzy character. Hence consideration of fuzzy skewness and kurtosis coefficients is expedient. Investigation of the basic characteristics changes- dynamics of GTE work parameters allows to draw conclusion on necessity of the Fuzzy Statistical Analysis at preliminary identification of the engines' technical condition. Researches of correlation coefficients values- changes shows also on their fuzzy character. Therefore for models choice the application of the Fuzzy Correlation Analysis results is offered. For checking of models adequacy is considered the Fuzzy Multiple Correlation Coefficient of Fuzzy Multiple Regression. At the information sufficiency is offered to use recurrent algorithm of aviation GTE technical condition identification (Hard Computing technology is used) on measurements of input and output parameters of the multiple linear and non-linear generalised models at presence of noise measured (the new recursive Least Squares Method (LSM)). The developed GTE condition monitoring system provides stage-bystage estimation of engine technical conditions. As application of the given technique the estimation of the new operating aviation engine temperature condition was made.
Abstract: Web applications have become complex and crucial for many firms, especially when combined with areas such as CRM (Customer Relationship Management) and BPR (Business Process Reengineering). The scientific community has focused attention to Web application design, development, analysis, testing, by studying and proposing methodologies and tools. Static and dynamic techniques may be used to analyze existing Web applications. The use of traditional static source code analysis may be very difficult, for the presence of dynamically generated code, and for the multi-language nature of the Web. Dynamic analysis may be useful, but it has an intrinsic limitation, the low number of program executions used to extract information. Our reverse engineering analysis, used into our WAAT (Web Applications Analysis and Testing) project, applies mutational techniques in order to exploit server side execution engines to accomplish part of the dynamic analysis. This paper studies the effects of mutation source code analysis applied to Web software to build application models. Mutation-based generated models may contain more information then necessary, so we need a pruning mechanism.
Abstract: Structural redundancy is an interesting point in
seismic design of structures. Initially, the structural redundancy is
described as indeterminate degree of a system. Although many definitions are presented for redundancy in structures, recently the
definition of structural redundancy has been related to the configuration of structural system and the number of lateral load
transferring directions in the structure. The steel frames with infill walls are general systems in the constructing of usual residential buildings in some countries. It is
obviously declared that the performance of structures will be affected by adding masonry infill walls. In order to investigate the effect of
infill walls on the redundancy of the steel frame which constructed
with masonry walls, the components of redundancy including redundancy variation index, redundancy strength index and
redundancy response modification factor were extracted for the
frames with masonry infills. Several steel frames with typical storey number and various numbers of bays were designed and considered.
The redundancy of frames with and without infill walls was evaluated by proposed method. The results showed the presence of infill causes increase of redundancy.
Abstract: The development of aid's systems for the medical
diagnosis is not easy thing because of presence of inhomogeneities in
the MRI, the variability of the data from a sequence to the other as
well as of other different source distortions that accentuate this
difficulty. A new automatic, contextual, adaptive and robust
segmentation procedure by MRI brain tissue classification is
described in this article. A first phase consists in estimating the
density of probability of the data by the Parzen-Rozenblatt method.
The classification procedure is completely automatic and doesn't
make any assumptions nor on the clusters number nor on the
prototypes of these clusters since these last are detected in an
automatic manner by an operator of mathematical morphology called
skeleton by influence zones detection (SKIZ). The problem of
initialization of the prototypes as well as their number is transformed
in an optimization problem; in more the procedure is adaptive since it
takes in consideration the contextual information presents in every
voxel by an adaptive and robust non parametric model by the
Markov fields (MF). The number of bad classifications is reduced by
the use of the criteria of MPM minimization (Maximum Posterior
Marginal).
Abstract: The purposes of researches - to estimate implicit ethnic attitudes by direct and indirect methods, to determine the accordance of two types measuring, to investigate influence of task type used in an experiment, on the results of measuring, as well as to determine a presence or communication between recent episodic events and chronologic correlations of ethnic attitudes. Method of the implicit measuring - an evaluative priming (EPT) carried out with the use of different SOA intervals, explicit methods of research are G.Soldatova-s types of ethnic identity, G.Soldatova-s index of tolerance, E.Bogardus scale of social distance. During five stages of researches received results open some aspects of implicit measuring, its correlation with the results of self-reports on different SOA intervals, connection of implicit measuring with emotional valence of episodic events of participants and other indexes, presenting a contribution to the decision of implicit measuring application problem for study of different social constructs
Abstract: This paper addresses parameter and state estimation problem in the presence of the perturbation of observer gain bounded input disturbances for the Lipschitz systems that are linear in unknown parameters and nonlinear in states. A new nonlinear adaptive resilient observer is designed, and its stability conditions based on Lyapunov technique are derived. The gain for this observer is derived systematically using linear matrix inequality approach. A numerical example is provided in which the nonlinear terms depend on unmeasured states. The simulation results are presented to show the effectiveness of the proposed method.
Abstract: The scalar wave equation for a potential in a curved space time, i.e., the Laplace-Beltrami equation has been studied in this work. An action principle is used to derive a finite element algorithm for determining the modes of propagation inside a waveguide of arbitrary shape. Generalizing this idea, the Maxwell theory in a curved space time determines a set of linear partial differential equations for the four electromagnetic potentials given by the metric of space-time. Similar to the Einstein-s formulation of the field equations of gravitation, these equations are also derived from an action principle. In this paper, the expressions for the action functional of the electromagnetic field have been derived in the presence of gravitational field.
Abstract: This paper introduces a new approach for the performance
analysis of adaptive filter with error saturation nonlinearity in
the presence of impulsive noise. The performance analysis of adaptive
filters includes both transient analysis which shows that how fast
a filter learns and the steady-state analysis gives how well a filter
learns. The recursive expressions for mean-square deviation(MSD)
and excess mean-square error(EMSE) are derived based on weighted
energy conservation arguments which provide the transient behavior
of the adaptive algorithm. The steady-state analysis for co-related
input regressor data is analyzed, so this approach leads to a new
performance results without restricting the input regression data to
be white.