Abstract: The relationship between different types of Molybdenum disulfide greases under extreme pressure loading and different speed situations have been studied using Design of Experiment (DOE) under 1200rpm steady state rotational speed and cyclic frequencies between 2400 and 1200rpm using a Plint machine software to set up the different rotational speed situations.
Research described here is aimed at providing good friction and wear performance while optimizing cyclic frequencies and MoS2 concentration due to the recent concern about grease behavior in extreme pressure applications. Extreme load of 785 Newton was used in conjunction with different cyclic frequencies (2400rpm -3.75min, 1200rpm -7.5min, 2400rpm -3.75min, 1200rpm -7.5min), to examine lithium based grease with and without MoS2 for equal number of revolutions, and a total run of 36000 revolutions; then compared to 1200rpm steady speed for the same total number of revolutions. 4 Ball wear tester was utilized to run large number of experiments randomly selected by the DOE software. The grease was combined with fine grade MoS2 or technical grade then heated to 750C and the wear scar width was collected at the end of each test. DOE model validation results verify that the data were very significant and can be applied to a wide range of extreme pressure applications. Based on simulation results and Scanning Electron images (SEM), it has been found that wear was largely dependent on the cyclic frequency condition. It is believed that technical grade MoS2 greases under faster cyclic speeds perform better and provides antiwear film that can resist extreme pressure loadings. Figures showed reduced wear scars width and improved frictional values.
Abstract: Optical network uses a tool for routing called Latin
router. These routers use particular algorithms for routing. For
example, we can refer to LDF algorithm that uses backtracking (one
of CSP methods) for problem solving. In this paper, we proposed
new approached for completion routing table (DRA&CRA
algorithm) and compare with pervious proposed ways and showed
numbers of backtracking, blocking and run time for DRA algorithm
less than LDF and CRA algorithm.
Abstract: Recent research has shown that milk proteins can
yield bioactive peptides with opioid, mineral binding,
cytomodulatory, antihypertensive, immunostimulating, antimicrobial
and antioxidative activity in the human body. Bioactive peptides are
encrypted in milk proteins and are only released by enzymatic
hydrolysis in vivo during gastrointestinal digestion, food processing
or by microbial enzymes in fermented products. At present
significant research is being undertaken on the health effects of
bioactive peptides. A variety of naturally formed bioactive peptides
have been found in fermented dairy products, such as yoghurt, sour
milk and cheese. In particular, antihypertensive peptides have been
identified in fermented milks, whey and ripened cheese. Some of
these peptides have been commercialized in the form of fermented
milks. Bioactive peptides have the potential to be used in the
formulation of health-enhancing nutraceuticals, and as potent drugs
with well defined pharmacological effects.
Abstract: In this study, a three-dimensional haptotaxis model to simulate the migration of a population of cancer cells has been proposed. The invasion of cancer cells is related with the hapto-attractant and the effect of the interface energies between the cells and the ECM. The diffuse interface model, which incorporates the haptotaxis mechanism and interface energies, is employed. The semi-implicit Fourier spectral scheme is adopted for efficient evaluation of the simulation. The simulation results thoroughly reveal the dynamics of cancer-cell migration.
Abstract: The sonochemical decolorization and degradation of azo dye Methyl violet using Fenton-s reagent in the presence of a high-frequency acoustic field has been investigated. Dyeing and textile effluents are the major sources of azo dyes, and are most troublesome among industrial wastewaters, causing imbalance in the eco-system. The effect of various operating conditions (initial concentration of dye, liquid-phase temperature, ultrasonic power and frequency and process time) on sonochemical degradation was investigated. Conversion was found to increase with increase in initial concentration, temperature, power level and frequency. Both horntype and tank-type sonicators were used, at various power levels (250W, 400W and 500W) for frequencies ranging from 20 kHz - 1000 kHz. A 'Process Intensification' parameter PI, was defined to quantify the enhancement of the degradation reaction by ultrasound when compared to control (i.e., without ultrasound). The present work clearly demonstrates that a high-frequency ultrasonic bath can be used to achieve higher process throughput and energy efficiency at a larger scale of operation.
Abstract: Based on the combined shape feature and texture
feature, a fast object detection method with rotation invariant features
is proposed in this paper. A quick template matching scheme based
online learning designed for online applications is also introduced in
this paper. The experimental results have shown that the proposed
approach has the features of lower computation complexity and
higher detection rate, while keeping almost the same performance
compared to the HOG-based method, and can be more suitable for
run time applications.
Abstract: To produce sugar and ethanol, sugarcane processing
generates several agricultural residues, being straw and bagasse is
considered as the main among them. And what to do with this
residues has been subject of many studies and experiences in an
industry that, in recent years, highlighted by the ability to transform
waste into valuable products such as electric power. Cellulose is the
main component of these materials. It is the most common organic
polymer and represents about 1.5 x 1012 tons of total production of
biomass per year and is considered an almost inexhaustible source of
raw material. Pretreatment with mineral acids is one of the most
widely used as stage of cellulose extraction from lignocellulosic
materials for solubilizing most of the hemicellulose content. This
study had as goal to find the best reaction time of sugarcane bagasse
pretreatment with sulfuric acid in order to minimize the losses of
cellulose concomitantly with the highest possible removal of
hemicellulose and lignin. It was found that the best time for this
reaction was 40 minutes, in which it was reached a loss of
hemicelluloses around 70% and lignin and cellulose, around 15%.
Over this time, it was verified that the cellulose loss increased and
there was no loss of lignin and hemicellulose.
Abstract: In this work, we study elliptic divisibility sequences
over finite fields. Morgan Ward in [14], [15] gave arithmetic theory
of elliptic divisibility sequences and formulas for elliptic divisibility
sequences with rank two over finite field Fp. We study elliptic
divisibility sequences with rank three, four and five over a finite field
Fp, where p > 3 is a prime and give general terms of these sequences
and then we determine elliptic and singular curves associated with
these sequences.
Abstract: The work describes the use of a synthetic transmit
aperture (STA) with a single element transmitting and all elements
receiving in medical ultrasound imaging. STA technique is a novel
approach to today-s commercial systems, where an image is acquired
sequentially one image line at a time that puts a strict limit on the
frame rate and the amount of data needed for high image quality. The
STA imaging allows to acquire data simultaneously from all
directions over a number of emissions, and the full image can be
reconstructed.
In experiments a 32-element linear transducer array with 0.48 mm
inter-element spacing was used. Single element transmission aperture
was used to generate a spherical wave covering the full image region.
The 2D ultrasound images of wire phantom are presented obtained
using the STA and commercial ultrasound scanner Antares to
demonstrate the benefits of the SA imaging.
Abstract: Computational simulation of steam flow and heat transfer in power plant condensers on the basis of the threedimensional mathematical model for the flow through porous media is presented. In order to solve the mathematical model of steam flow and heat transfer in power plant condensers, the Streamline Upwind Petrov-Galerkin finite element method is applied. By comparison of the results of simulation with experimental results about an experimental condenser, it is confirmed that SUPG finite element method can be successfully applied for solving the three-dimensional mathematical model of steam flow and heat transfer in power plant condensers.
Abstract: Based on the one-bit-matching principle and by turning the de-mixing matrix into an orthogonal matrix via certain normalization, Ma et al proposed a one-bit-matching learning algorithm on the Stiefel manifold for independent component analysis [8]. But this algorithm is not adaptive. In this paper, an algorithm which can extract kurtosis and its sign of each independent source component directly from observation data is firstly introduced.With the algorithm , the one-bit-matching learning algorithm is revised, so that it can make the blind separation on the Stiefel manifold implemented completely in the adaptive mode in the framework of natural gradient.
Abstract: In recent years, there have been attempts to store
natural gas in adsorptive form. This is called adsorptive natural gas,
or ANG. The problem with this technology is the low sorption
capacity. The purpose is to achieve compressed natural gas (CNG)
capacity of 230 V/V. Further research is required to achieve such
target. Several research studies have been performed with this target;
through either the modification or development of new sorbents or
the optimization of the operation sorption process itself. In this work,
storage of methane on molecular sieves 5A and 13X was studied on
dry basis, and on wet basis to certain extent. The temperature and the
pressure dynamics were investigated. The results indicated that
regardless of the charge pressure, the time for the peak temperature
during the methane charge process is always the same. This can be
used as a characteristic of the adsorbent. The total achieved
deliveries using molecular sieves were much lower than that of
activated carbons; 53.0 V/V for the case of 13X molecular sieves and
43 V/V for the case of 5A molecular sieves, both at 2oC and 4 MPa
(580 psi). Investigation of charge pressure dynamic using wet
molecular sieves at 2oC and a mass ratio of 0.5, revealed slowness of
the process and unexpected behavior.
Abstract: In order to apply partially filled steel grid composite deck as the horizontal supporting structure of various kinds of infrastructures, the variation of its flexural strength according to design parameters such as cross and longitudinal bars constituting the steel grid and the type of shear connection is evaluated and compared experimentally. The result shows that the design sensitivity of the deck to the spacing of the cross bars is insignificant in the case of structure with low risk of punching failure or without load distribution problem. By means of shear connection composed by transverse rebar and longitudinal bar without additional shear stud bolts, the complete interaction between steel grid and concrete slab is able to be achieved and the composite deck can develop its bending resistance capacity.
Abstract: It has been shown that a load discontinuity at the end of
an impulse will result in an extra impulse and hence an extra amplitude
distortion if a step-by-step integration method is employed to yield the
shock response. In order to overcome this difficulty, three remedies
are proposed to reduce the extra amplitude distortion. The first remedy
is to solve the momentum equation of motion instead of the force
equation of motion in the step-by-step solution of the shock response,
where an external momentum is used in the solution of the momentum
equation of motion. Since the external momentum is a resultant of the
time integration of external force, the problem of load discontinuity
will automatically disappear. The second remedy is to perform a single
small time step immediately upon termination of the applied impulse
while the other time steps can still be conducted by using the time step
determined from general considerations. This is because that the extra
impulse caused by a load discontinuity at the end of an impulse is
almost linearly proportional to the step size. Finally, the third remedy
is to use the average value of the two different values at the integration
point of the load discontinuity to replace the use of one of them for
loading input. The basic motivation of this remedy originates from the
concept of no loading input error associated with the integration point
of load discontinuity. The feasibility of the three remedies are
analytically explained and numerically illustrated.
Abstract: The aim of this study is to determine the basic information and communication technology (ICT) skills that may be needed by students studying in the 8th grade of the primary education in their cooperative project works implemented via the Internet. Within the scope of the study, the curriculum used for European Computer Driving License (ECDL) and the curriculum used in Turkey are also compared in terms of the ability to use ICT, which is aimed to be provided to the students. The research population of the study, during which the pre test – post test control group experimental model was used, consisted of 40 students from three different schools. In the first stage of the study, the skills that might be needed by students for their cooperative project works implemented via the Internet were determined through examination of the completed Comenious, e – twinning and WorldLinks projects. In the second stage of the study, the curriculums of the Turkish Ministry of National Education (MEB) and ECDL were evaluated by seven different teachers in line with these skills. Also in this study the ECDL and MEB curriculums were compared in terms of capability to provide the skills to implement cooperative projects via the Internet. In line with the findings of the study, the skills that might be needed by students to implement cooperative projects via the Internet were outlined, and existence of a significant difference was established in favor of the ECDL curriculum upon comparison of both curriculums in accordance with this outline (U = 50,500; p
Abstract: This study employs auto-regressive distributed lag (ARDL) bounds approach to cointegration for long run and errorcorrection modeling (ECM) for short run analysis to examine the relationship between revenue gap and economic growth for Pakistan using annual time series data over the period 1980 to 2008. The short and long run results indicate that revenue gap is statistical significant and negatively effect economic growth. The significant and negative coefficient of error correction term in ECM indicates that after a shock, the long rum equilibrium will again converge towards equilibrium about 10.406 percent within a year.
Abstract: Wind is among the potential energy resources which
can be harnessed to generate wind energy for conversion into
electrical power. Due to the variability of wind speed with time and
height, it becomes difficult to predict the generated wind energy more
optimally. In this paper, an attempt is made to establish a
probabilistic model fitting the wind speed data recorded at
Makambako site in Tanzania. Wind speeds and direction were
respectively measured using anemometer (type AN1) and wind Vane
(type WD1) both supplied by Delta-T-Devices at a measurement
height of 2 m. Wind speeds were then extrapolated for the height of
10 m using power law equation with an exponent of 0.47. Data were
analysed using MINITAB statistical software to show the variability
of wind speeds with time and height, and to determine the underlying
probability model of the extrapolated wind speed data. The results
show that wind speeds at Makambako site vary cyclically over time;
and they conform to the Weibull probability distribution. From these
results, Weibull probability density function can be used to predict
the wind energy.
Abstract: The purpose of this study was to investigate the effects of computer–based instructional designs, namely modality and redundancy principles on the attitude and learning of music theory among primary pupils of different Music Intelligence levels. The lesson of music theory was developed in three different modes, audio and image (AI), text with image (TI) and audio with image and text (AIT). The independent variables were the three modes of courseware. The moderator variable was music intelligence. The dependent variables were the post test score. ANOVA was used to determine the significant differences of the pretest scores among the three groups. Analyses of covariance (ANCOVA) and Post hoc were carried out to examine the main effects as well as the interaction effects of the independent variables on the dependent variables. High music intelligence pupils performed significantly better than low music intelligence pupils in all the three treatment modes. The AI mode was found to help pupils with low music intelligence significantly more than the TI and AIT modes.
Abstract: Among various testing methodologies, Built-in Self-
Test (BIST) is recognized as a low cost, effective paradigm. Also,
full adders are one of the basic building blocks of most arithmetic
circuits in all processing units. In this paper, an optimized testable 2-
bit full adder as a test building block is proposed. Then, a BIST
procedure is introduced to scale up the building block and to generate
a self testable n-bit full adders. The target design can achieve 100%
fault coverage using insignificant amount of hardware redundancy.
Moreover, Overall test time is reduced by utilizing polymorphic
gates and also by testing full adder building blocks in parallel.
Abstract: Carbon Capture & Storage (CCS) is one of the various
methods that can be used to reduce the carbon footprint of the
energy sector. This paper focuses on the absorption of CO2 from
flue gas using packed columns, whose efficiency is highly dependent
on the structure of the liquid films within the column. To study the
characteristics of liquid films a CFD solver, OpenFOAM is utilised
to solve two-phase, isothermal film flow using the volume-of-fluid
(VOF) method. The model was validated using existing experimental
data and the Nusselt theory. It was found that smaller plate inclination
angles, with respect to the horizontal plane, resulted in larger wetted
areas on smooth plates. However, only a slight improvement in
the wetted area was observed. Simulations were also performed
using a ridged plate and it was observed that these surface textures
significantly increase the wetted area of the plate. This was mainly
attributed to the channelling effect of the ridges, which helped to
oppose the surface tension forces trying to minimise the surface area.
Rivulet formations on the ridged plate were also flattened out and
spread across a larger proportion of the plate width.