Abstract: Signalized intersections on high-volume arterials are
often congested during peak hours, causing a decrease in through
movement efficiency on the arterial. Much of the vehicle delay
incurred at conventional intersections is caused by high left-turn
demand. Unconventional intersection designs attempt to reduce
intersection delay and travel time by rerouting left-turns away from
the main intersection and replacing it with right-turn followed by Uturn.
The proposed new type of U-turn intersection is geometrically
designed with a raised island which provides a protected U-turn
movement. In this study several scenarios based on different
distances between U-turn and main intersection, traffic volume of
major/minor approaches and percentage of left-turn volumes were
simulated by use of AIMSUN, a type of traffic microsimulation
software. Subsequently some models are proposed in order to
compute travel time of each movement. Eventually by correlating
these equations to some in-field collected data of some implemented
U-turn facilities, the reliability of the proposed models are approved.
With these models it would be possible to calculate travel time of
each movement under any kind of geometric and traffic condition. By
comparing travel time of a conventional signalized intersection with
U-turn intersection travel time, it would be possible to decide on
converting signalized intersections into this new kind of U-turn
facility or not. However comparison of travel time is not part of the
scope of this research. In this paper only travel time of this innovative
U-turn facility would be predicted. According to some before and
after study about the traffic performance of some executed U-turn
facilities, it is found that commonly, this new type of U-turn facility
produces lower travel time. Thus, evaluation of using this type of
unconventional intersection should be seriously considered.
Abstract: In this paper, algorithms for the automatic localisation
of two anatomical soft tissue landmarks of the head the medial
canthus (inner corner of the eye) and the tragus (a small, pointed,
cartilaginous flap of the ear), in CT images are describet. These
landmarks are to be used as a basis for an automated image-to-patient
registration system we are developing. The landmarks are localised
on a surface model extracted from CT images, based on surface
curvature and a rule based system that incorporates prior knowledge
of the landmark characteristics. The approach was tested on a dataset
of near isotropic CT images of 95 patients. The position of the
automatically localised landmarks was compared to the position of
the manually localised landmarks. The average difference was 1.5
mm and 0.8 mm for the medial canthus and tragus, with a maximum
difference of 4.5 mm and 2.6 mm respectively.The medial canthus
and tragus can be automatically localised in CT images, with
performance comparable to manual localisation
Abstract: The prediction of transmembrane helical segments
(TMHs) in membrane proteins is an important field in the
bioinformatics research. In this paper, a new method based on discrete
wavelet transform (DWT) has been developed to predict the number
and location of TMHs in membrane proteins. PDB coded as 1KQG
was chosen as an example to describe the prediction of the number and
location of TMHs in membrane proteins by using this method. To
access the effect of the method, 80 proteins with known 3D-structure
from Mptopo database are chosen at random as the test objects
(including 325 TMHs), 308 of which can be predicted accurately, the
average predicted accuracy is 96.3%. In addition, the above 80
membrane proteins are divided into 13 groups according to their
function and type. In particular, the results of the prediction of TMHs
of the 13 groups are satisfying.
Abstract: The purpose of this study is to determine in what
ways elementary education prospective teachers are being informed
about innovations and to explain the role of social influence in the
usage process of a technological innovation in terms of genders. The
study group consisted of 300 prospective teachers, including 234
females and 66 males. Data have been collected by a questionnaire
developed by the researchers. The result of the study showed that,
while prospective teachers are being informed about innovations
most frequently by mass media, they rarely seek to take expert
advice. In addition, analysis of results showed that the social
influence on females were significantly higher than males in usage
process of a technological innovation.
Abstract: Recent years have witnessed the rapid development of
the Internet and telecommunication techniques. Information security
is becoming more and more important. Applications such as covert
communication, copyright protection, etc, stimulate the research of
information hiding techniques. Traditionally, encryption is used to
realize the communication security. However, important information
is not protected once decoded. Steganography is the art and science
of communicating in a way which hides the existence of the communication.
Important information is firstly hidden in a host data, such
as digital image, video or audio, etc, and then transmitted secretly
to the receiver.In this paper a data hiding model with high security
features combining both cryptography using finite state sequential
machine and image based steganography technique for communicating
information more securely between two locations is proposed.
The authors incorporated the idea of secret key for authentication
at both ends in order to achieve high level of security. Before the
embedding operation the secret information has been encrypted with
the help of finite-state sequential machine and segmented in different
parts. The cover image is also segmented in different objects through
normalized cut.Each part of the encoded secret information has been
embedded with the help of a novel image steganographic method
(PMM) on different cuts of the cover image to form different stego
objects. Finally stego image is formed by combining different stego
objects and transmit to the receiver side. At the receiving end different
opposite processes should run to get the back the original secret
message.
Abstract: Ultrasonic machining (USM) is a non-traditional
machining process being widely used for commercial machining of
brittle and fragile materials such as glass, ceramics and
semiconductor materials. However, USM could be a viable
alternative for machining a tough material such as titanium; and this
aspect needs to be explored through experimental research. This
investigation is focused on exploring the use of ultrasonic machining
for commercial machining of pure titanium (ASTM Grade-I) and
evaluation of tool wear rate (TWR) under controlled experimental
conditions. The optimal settings of parameters are determined
through experiments planned, conducted and analyzed using Taguchi
method. In all, the paper focuses on parametric optimization of
ultrasonic machining of pure titanium metal with TWR as response,
and validation of the optimized value of TWR by conducting
confirmatory experiments.
Abstract: Soft topological spaces are considered as mathematical tools for dealing with uncertainties, and a fuzzy topological space
is a special case of the soft topological space. The purpose of this paper is to study soft topological spaces. We introduce some new concepts in soft topological spaces such as soft closed mapping, soft open mappings, soft connected spaces and soft paracompact spaces. We also redefine the concept of soft points such that it is reasonable in soft topological spaces. Moreover, some basic properties of these concepts are explored.
Abstract: This paper describes analysis of low velocity transverse impact on fully backed sandwich beams with composite faces from Eglass/epoxy and cores from Polyurethane or PVC. Indentation on sandwich beams has been analyzed with the existing theories and modeled with the FE code ABAQUS, also loadings have been done experimentally to verify theoretical results. Impact on fully backed has been modeled in two cases of impactor energy with SDOF model (single-degree-of-freedom) and indentation stiffness: lower energy for elastic indentation of sandwich beams and higher energy for plastic area in indentation. Impacts have been modeled by ABAQUS. Impact results can describe response of beam in terms of core and faces thicknesses, core material, indentor energy and energy absorbed. The foam core is modeled using the crushable foam material model and response of the foam core is experimentally characterized in uniaxial compression with higher velocity loading to define quasi impact behaviour.
Abstract: This study is a descriptive-normative research. It
attempted to investigate the restaurants’ firm performance in terms of
the customers and restaurant personnel’s degree of satisfaction. A
total of 12 restaurants in Bangkok, Thailand that offer Thai cuisine
were included in this study. It involved 24 stockholders/managers,
120 subordinates and 360 customers. General Managers and
restaurants’ stockholders, 10 staffs, and 30 costumers for each
restaurant were chosen for random sampling. This study found that
respondents are slightly satisfied with their work environment but are
generally satisfied with the accessibility to transportation, to malls,
convenience, safety, recreation, noise-free, and attraction; customers
find the Quality of Food in most Thai Cuisines like services, prices of
food, sales promotion, and capital and length of service satisfactory.
Therefore, both stockholder-related and personnel-related factors
which are influenced by restaurant, personnel, and customer-related
factors are partially accepted whereas; customer-related factors which
are influenced by restaurant, personnel and customer-related factors
are rejected.
Abstract: Fuller’s earth is a fine-grained, naturally occurring substance that has a substantial ability to adsorb impurities. In the present study Fuller’s earth has been characterized and used for the removal of Pb(II) from aqueous solution. The effect of various physicochemical parameters such as pH, adsorbent dosage and shaking time on adsorption were studied. The result of the equilibrium studies showed that the solution pH was the key factor affecting the adsorption. The optimum pH for adsorption was 5. Kinetics data for the adsorption of Pb(II) was best described by pseudo-second order model. The effective diffusion co-efficient for Pb(II) adsorption was of the order of 10-8 m2/s. The adsorption data for metal adsorption can be well described by Langmuir adsorption isotherm. The maximum uptake of metal was 103.3 mg/g of adsorbent. Mass transfer analysis was also carried out for the adsorption process. The values of mass transfer coefficients obtained from the study indicate that the velocity of the adsorbate transport from bulk to the solid phase was quite fast. The mean sorption energy calculated from Dubinin-Radushkevich isotherm indicated that the metal adsorption process was chemical in nature.
Abstract: This paper discusses aspects of re-design of loadshedding
schemes with respect to actual developments in the Kosovo
power system. Load-shedding is a type of emergency control that is
designed to ensure system stability by reducing power system load to
match the power generation supply. This paper presents a new
adaptive load-shedding scheme that provides emergency protection
against excess frequency decline, in cases when the Kosovo power
system might be disconnected from the regional transmission
network. The proposed load-shedding scheme uses the local
frequency rate information to adapt the load-shedding pattern to suit
the size and location of the occurring disturbance. The proposed
scheme is tested in a software simulation on a large scale PSS/E
model which represents nine power system areas of Southeast Europe
including the Kosovo power system.
Abstract: Color image segmentation plays an important role in
computer vision and image processing areas. In this paper, the
features of Volterra filter are utilized for color image segmentation.
The discrete Volterra filter exhibits both linear and nonlinear
characteristics. The linear part smoothes the image features in
uniform gray zones and is used for getting a gross representation of
objects of interest. The nonlinear term compensates for the blurring
due to the linear term and preserves the edges which are mainly used
to distinguish the various objects. The truncated quadratic Volterra
filters are mainly used for edge preserving along with Gaussian noise
cancellation. In our approach, the segmentation is based on K-means
clustering algorithm in HSI space. Both the hue and the intensity
components are fully utilized. For hue clustering, the special cyclic
property of the hue component is taken into consideration. The
experimental results show that the proposed technique segments the
color image while preserving significant features and removing noise
effects.
Abstract: Paper is dealing with vulnerability concerning elements of hydrological structures and elements of technological equipments which are acceptable for groundwater resources. The vulnerability assessment stems from the application of the register of hazards and a potential threat to individual water source elements within each type of hazard. The proposed procedure is pattern for assessing the risks of disturbance, damage, or destruction of water source by the identified natural or technological hazards and consequently for classification of these risks in relation to emergency water supply. Using of this procedure was verified on selected groundwater resource in particular region, which seems to be as potentially useful for crisis planning system.
Abstract: Semiconductor nanomaterials like TiO2 nanoparticles
(TiO2-NPs) approximately less than 100 nm in diameter have become
a new generation of advanced materials due to their novel and
interesting optical, dielectric, and photo-catalytic properties. With the
increasing use of NPs in commerce, to date few studies have
investigated the toxicological and environmental effects of NPs.
Motivated by the importance of TiO2-NPs that may contribute to the
cancer research field especially from the treatment prospective
together with the fractal analysis technique, we have investigated the
effect of TiO2-NPs on colony morphology in the dark condition
using fractal dimension as a key morphological characterization
parameter. The aim of this work is mainly to investigate the cytotoxic
effects of TiO2-NPs in the dark on the growth of human cervical
carcinoma (HeLa) cell colonies from morphological aspect. The in
vitro studies were carried out together with the image processing
technique and fractal analysis. It was found that, these colonies were
abnormal in shape and size. Moreover, the size of the control
colonies appeared to be larger than those of the treated group. The
mean Df +/- SEM of the colonies in untreated cultures was
1.085±0.019, N= 25, while that of the cultures treated with TiO2-NPs
was 1.287±0.045. It was found that the circularity of the control
group (0.401±0.071) is higher than that of the treated group
(0.103±0.042). The same tendency was found in the diameter
parameters which are 1161.30±219.56 μm and 852.28±206.50 μm
for the control and treated group respectively. Possible explanation of
the results was discussed, though more works need to be done in
terms of the for mechanism aspects. Finally, our results indicate that
fractal dimension can serve as a useful feature, by itself or in
conjunction with other shape features, in the classification of cancer
colonies.
Abstract: Stage bus operated in the mixed traffic might always meet many problems about low quality and reliability of services. The low quality and reliability of bus service can make the system not attractive and directly reduce the interest of using bus service. This paper presents the result of field investigation and analysis of on-time performance and service regularity of stage bus in mixed traffic. Data for analysis was collected from the field by on-board observation along the Ipoh-Lumut corridor in Perak, Malaysia. From analysis and discussion, it can be concluded that on-time performance and service regularity varies depend on station, typical day, time period, operation characteristics of bus and characteristics of traffic. The on-time performance and service regularity of stage bus in mixed traffic can be derived by using data collected by onboard survey. It is clear that on-time performance and service regularity of the existing stage bus system was low.
Abstract: The comparisons of two typical fluidic thrust vectoring exhaust nozzles including two-dimensional(2-D) nozzle and axisymmetric nozzle on aerodynamic characteristics was presented by numerical simulation. The results show: the thrust vector angles increased with the increasing secondary flow but decreased with the nozzle pressure ratio (NPR) increasing. With the same secondary flow and NPR, the thrust vector angles of 2-D nozzle were higher than the axisymmetric nozzle-s. So with the lower NPR and more secondary weight flow, the much higher thrust vector angle was caused by 2-D fluidic nozzle. And with the higher NPR and less secondary weight flow, there was not much difference in angular dimension between two nozzles.
Abstract: Ability of accurate and reliable location estimation in
indoor environment is the key issue in developing great number of
context aware applications and Location Based Services (LBS).
Today, the most viable solution for localization is the Received
Signal Strength (RSS) fingerprinting based approach using wireless
local area network (WLAN). This paper presents two RSS
fingerprinting based approaches – first we employ widely used
WLAN based positioning as a reference system and then investigate
the possibility of using GSM signals for positioning. To compare
them, we developed a positioning system in real world environment,
where realistic RSS measurements were collected. Multi-Layer
Perceptron (MLP) neural network was used as the approximation
function that maps RSS fingerprints and locations. Experimental
results indicate advantage of WLAN based approach in the sense of
lower localization error compared to GSM based approach, but GSM
signal coverage by far outreaches WLAN coverage and for some
LBS services requiring less precise accuracy our results indicate that
GSM positioning can also be a viable solution.
Abstract: Scaffolds play a key role in tissue engineering and can be produced in many different ways depending on the applications and the materials used. Most researchers used an experimental trialand- error approach into new biomaterials but computer simulation applied to tissue engineering can offer a more exhaustive approach to test and screen out biomaterials. This paper develops the model of scaffolds and Computational Fluid Dynamics that show the value of computer simulations in determining the influence of the geometrical scaffold parameter porosity, pore size and shape on the permeability of scaffolds, magnitude of velocity, drop pressure, shear stress distribution and level and the proper design of the geometry of the scaffold. This creates a need for more advanced studies that include aspects of dynamic conditions of a micro fluid passing through the scaffold were characterized for tissue engineering applications and differentiation of tissues within scaffolds.
Abstract: Vinegar is a precious food additive and complement as well as effective preservative against food spoilage. Recently traditional vinegar production has been improved using various natural substrates and fruits such as grape, palm, cherry, coconut, date, sugarcane, rice and balsam. These neoclassical fermentations resulted in several vinegar types with different tastes, fragrances and nutritional values because of applying various acetic acid bacteria as starters. Acetic acid bacteria include genera Acetobacter, Gluconacetobacter and Gluconobacter according to latest edition of Bergy-s Manual of Systematic Bacteriology that classifies genera on the basis of their 16s RNA differences. Acetobacter spp as the main vinegar starters belong to family Acetobacteraceae that are gram negative obligate aerobes, chemoorganotrophic bacilli that are oxidase negative and oxidize ethanol to acetic acid. In this research we isolated and identified a native Acetobacter strain with high acetic acid productivity and tolerance against high ethanol concentrations from Iranian peach as a summer delicious fruit that is very susceptible to food spoilage and decay. We used selective and specific laboratorial culture media such as Standard GYC, Frateur and Carr medium. Also we used a new industrial culture medium and a miniature fermentor with a new aeration system innovated by Pars Yeema Biotechnologists Co., Isfahan Science and Technology Town (ISTT), Isfahan, Iran. The isolated strain was successfully cultivated in modified Carr media with 2.5% and 5% ethanol simultaneously in high temperatures, 34 - 40º C after 96 hours of incubation period. We showed that the increase of ethanol concentration resulted in rising of strain sensitivity to high temperature. In conclusion we isolated and characterized a new Acetobacter strain from Iranian peach that could be considered as a potential strain for production of a new vinegar type, peach vinegar, with a delicious taste and advantageous nutritional value in food biotechnology and industrial microbiology.
Abstract: High redundancy and strong uncertainty are two main characteristics for underwater robotic manipulators with unlimited workspace and mobility, but they also make the motion planning and control difficult and complex. In order to setup the groundwork for the research on control schemes, the mathematical representation is built by using the Denavit-Hartenberg (D-H) method [9]&[12]; in addition to the geometry of the manipulator which was studied for establishing the direct and inverse kinematics. Then, the dynamic model is developed and used by employing the Lagrange theorem. Furthermore, derivation and computer simulation is accomplished using the MATLAB environment. The result obtained is compared with mechanical system dynamics analysis software, ADAMS. In addition, the creation of intelligent artificial skin using Interlink Force Sensing ResistorTM technology is presented as groundwork for future work