Abstract: Packing problems arise in a wide variety of application
areas. The basic problem is that of determining an efficient arrangement
of different objects in a region without any overlap and
with minimal wasted gap between shapes. This paper presents a
novel population based approach for optimizing arrangement of irregular
shapes. In this approach, each shape is coded as an agent and
the agents' reproductions and grouping policies results in arrangements
of the objects in positions with least wasted area between
them. The approach is implemented in an application for cutting
sheets and test results on several problems from literature are presented.
Abstract: Liquid-liquid extraction is a process using two immiscible
liquids to extract compounds from one phase without high
temperature requirement. Mostly, the technical implementation of
this process is carried out in mixer-settlers or extraction columns. In
real chemical processes, chemicals may have high viscosity and
contain impurities. These impurities may change the settling behavior
of the process without measurably changing the physical properties
of the phases. In the current study, the settling behavior and the affected
parameters in a high-viscosity system were observed. Batchsettling
experiments were performed to experimentally quantify the
settling behavior and the mixer-settler model of Henschke [1] was
used to evaluate the behavior of the toluene + water system. The
viscosity of the system was increased by adding polyethylene glycol
4000 to the aqueous phase. NaCl and Na2SO4 were used to study the
influence of electrolytes. The results from this study show that increasing
the viscosity of water has a higher influence on the settling
behavior in comparison to the effects of the electrolytes. It can be
seen from the experiments that at high salt concentrations, there was
no effect on the settling behavior.
Abstract: The development and use of mobile devices as well as its integration within education systems to deliver electronic contents and to support real-time communications was the focus of this research. In order to investigate the software engineering issues in using mobile devices a research on electronic content was initiated. The Developed MP3 mobile software solution was developed as a prototype for testing and developing a strategy for designing a usable m-learning environment. The mobile software solution was evaluated using mobile device using the link: http://projects.seeu.edu.mk/mlearn. The investigation also tested the correlation between the two mobile learning indicators: electronic content and attention, based on the Task Based learning instructional method. The mobile software solution ''M-Learn“ was developed as a prototype for testing the approach and developing a strategy for designing usable m-learning environment. The proposed methodology is about what learning modeling approach is more appropriate to use when developing mobile learning software.
Abstract: This research paper designs a unique motion planner
of multiple platoons of nonholonomic car-like robots as a feasible
solution to the lane changing/merging maneuvers. The decentralized
planner with a leaderless approach and a path-guidance principle
derived from the Lyapunov-based control scheme generates collision
free avoidance and safe merging maneuvers from multiple lanes to a
single lane by deploying a split/merge strategy. The fixed obstacles
are the markings and boundaries of the road lanes, while the moving
obstacles are the robots themselves. Real and virtual road lane
markings and the boundaries of road lanes are incorporated into a
workspace to achieve the desired formation and configuration of the
robots. Convergence of the robots to goal configurations and the
repulsion of the robots from specified obstacles are achieved by
suitable attractive and repulsive potential field functions,
respectively. The results can be viewed as a significant contribution
to the avoidance algorithm of the intelligent vehicle systems (IVS).
Computer simulations highlight the effectiveness of the split/merge
strategy and the acceleration-based controllers.
Abstract: Fuel cell is an emerging technology in the field
of renewable energy sources which has the capacity to replace
conventional energy generation sources. Fuel cell utilizes hydrogen
energy to produce electricity. The electricity generated by the fuel
cell can’t be directly used for a specific application as it needs
proper power conditioning. Moreover, the output power fluctuates
with different operating conditions. To get a stable output power
at an economic rate, power conditioning circuit is essential for fuel
cell. This paper implements a two-staged power conditioning unit for
fuel cell based distributed generation using hysteresis current control
technique.
Abstract: Over recent years, the number of building integrated photovoltaic (BIPV) installations for home systems have been increasing in Malaysia. The paper concerns an analysis - as part of current Research and Development (R&D) efforts - to integrate photovoltaics as an architectural feature of a detached house in the new satellite township of Putrajaya, Malaysia. The analysis was undertaken using calculation and simulation tools to optimize performance of BIPV home system. In this study, a the simulation analysis was undertaken for selected bungalow units based on a long term recorded weather data for city of Kuala Lumpur. The simulation and calculation was done with consideration of a PV panels' tilt and direction, shading effect and economical considerations. A simulation of the performance of a grid connected BIPV house in Kuala Lumpur was undertaken. This case study uses a 60 PV modules with power output of 2.7 kW giving an average of PV electricity output is 255 kWh/month..
Abstract: Transdermal delivery of ondansetron hydrochloride (OdHCl) can prevent the problems encountered with oral ondansetron. In previously conducted studies, effect of amount of polyvinyl pyrrolidone, permeation enhancer and casting solvent on the physicochemical properties on OdHCl were investigated. It is feasible to develop ondansetron transdermal patch by using ethyl cellulose and polyvinyl pyrrolidone with dibutyl pthalate as plasticizer, however, the desired flux is not achieved. The primary aim of this study is to use dimethyl succinate (DMS) and propylene glycol that are not incorporated in previous studies to determine their effect on the physicochemical properties of an OdHCl transdermal patch using ethyl cellulose and polyvinyl pyrrolidone. This study also investigates the effect of permeation enhancer (eugenol and phosphatidylcholine) on the release of OdHCl. The results showed that propylene glycol is a more suitable plasticizer compared to DMS in the fabrication of OdHCl transdermal patch using ethyl cellulose and polyvinyl pyrrolidone as polymers. Propylene glycol containing patch has optimum drug content, thickness, moisture content and water absorption, tensile strength, and a better release profile than DMS. Eugenol and phosphatidylcholine can increase release of OdHCl from the patches. From the physicochemical result and permeation profile, a combination of 350mg of ethyl cellulose, 150mg polyvinyl pyrrolidone, 3% of total polymer weight of eugenol, and 40% of total polymer weight of propylene glycol is the most suitable formulation to develop an OdHCl patch. OdHCl release did not increase with increasing the percentage of plasticiser. DMS 4, PG 4, DMS 9, PG 9, DMS 14, and PG 14 gave better release profiles where using 300mg: 0mg, 300mg: 100mg, and 350mg: 150mg of EC: PVP. Thus, 40% of PG or DMS appeared to be the optimum amount of plasticiser when the above combination where EC: PVP was used. It was concluded from the study that a patch formulation containing 350mg EC, 150mg PVP, 40% PG and 3% eugenol is the best transdermal matrix patch compositions for the uniform and continuous release/permeation of OdHCl over an extended period. This patch design can be used for further pharmacokinetic and pharmacodynamic studies in suitable animal models.
Abstract: This research studied the hypoglycemic effect of
water soluble polysaccharide (WSP) extracted from yam (Dioscorea
hispida) tuber by three different methods: aqueous extraction, papain
assisted extraction, and tempeh inoculums assisted extraction. The
two later extraction methods were aimed to remove WSP binding
protein to have more pure WSP. The hypoglycemic activities were
evaluated by means in vivo test on alloxan induced hyperglycemic
rats, glucose response test (GRT), in situ glucose absorption test
using everted sac, and short chain fatty acids (SCFAs) analysis. All
yam WSP extracts exhibited ability to decrease blood glucose level in
hyperglycemia condition as well as inhibited glucose absorption and
SCFA formation. The order of hypoglycemic activity was tempeh
inoculums assisted- >papain assisted- >aqueous WSP extracts. GRT
and in situ glucose absorption test showed that order of inhibition
was papain assisted- >tempeh inoculums assisted- >aqueous WSP
extracts. Digesta of caecum of yam WSP extracts oral fed rats had
more SCFA than control. Tempeh inoculums assisted WSP extract
exhibited the most significant hypoglycemic activity.
Abstract: An accurate procedure to determine free vibrations of
beams and plates is presented.
The natural frequencies are exact solutions of governing vibration
equations witch load to a nonlinear homogeny system.
The bilinear and linear structures considered simulate a bridge.
The dynamic behavior of this one is analyzed by using the theory of
the orthotropic plate simply supported on two sides and free on the
two others. The plate can be excited by a convoy of constant or
harmonic loads. The determination of the dynamic response of the
structures considered requires knowledge of the free frequencies and
the shape modes of vibrations. Our work is in this context. Indeed,
we are interested to develop a self-consistent calculation of the Eigen
frequencies.
The formulation is based on the determination of the solution of
the differential equations of vibrations. The boundary conditions
corresponding to the shape modes permit to lead to a homogeneous
system. Determination of the noncommonplace solutions of this
system led to a nonlinear problem in Eigen frequencies.
We thus, develop a computer code for the determination of the
eigenvalues. It is based on a method of bisection with interpolation
whose precision reaches 10 -12. Moreover, to determine the
corresponding modes, the calculation algorithm that we develop uses
the method of Gauss with a partial optimization of the "pivots"
combined with an inverse power procedure. The Eigen frequencies
of a plate simply supported along two opposite sides while
considering the two other free sides are thus analyzed. The results
could be generalized with the case of a beam by regarding it as a
plate with low width.
We give, in this paper, some examples of treated cases. The
comparison with results presented in the literature is completely
satisfactory.
Abstract: Since atmosphere pressure field is an actual envoy of
climatic signal the atmospheric Highs and Lows should be attributed
to the key active focal points within the ocean-atmosphere interplay
system. Here we were set a task to determine how the dynamics of
those centres of action relates to the climate change both on regional
and global scales. For this target the near-surface temperature and
atmospheric pressure differences between the Icelandic Low and the
Azores High were considered. The secular term of phase states of the
system under consideration was found divided into three
nonintersecting subsets. Each of that was put in consequence with
one of three climatic scenarios related to the periods of 1905-1935
(relatively warm phase), 1940-1970 (cold phase) and 1980-2000
(warm phase).
Abstract: The RANS method with Saffman-s turbulence model
was employed to solve the time-dependent turbulent Navier-Stokes
and energy equations for oscillating pipe flows. The method of
partial sums of the Fourier series is used to analyze the harmonic
velocity and temperature results. The complete structures of the
oscillating pipe flows and the averaged Nusselt numbers on the tube
wall are provided by numerical simulation over wide ranges of ReA
and ReR. Present numerical code is validated by comparing the
laminar flow results to analytic solutions and turbulence flow results
to published experimental data at lower and higher Reynolds
numbers respectively. The effects of ReA and ReR on the velocity,
temperature and Nusselt number distributions have been di scussed.
The enhancement of the heat transfer due to oscillating flows has
also been presented. By the way of analyzing the overall Nusselt
number over wide ranges of the Reynolds number Re and Keulegan-
Carpenter number KC, the optimal ratio of the tube diameter over
the oscillation amplitude is obtained based on the existence of a
nearly constant optimal KC number. The potential application of the
present results in sea water cooling has also been discussed.
Abstract: The improvement of irrigation systems in the Nile
Delta is one of the most important attempts in Egypt to implement
more effective irrigation technology by improving the existing
irrigation networks. Demand delivery system in the existing irrigation
network is using of mechanical gates structures to automatically
divert water from one portion of an agricultural field to another in the
desired amount and sequence. This paper discusses evaluating main
irrigation networks system under the government managed before
and after improvement systems in the Nile Delta. The overall results
indicate that policy of using the demand delivery concept through
irrigation networks is successful by improving water delivery
performance among them than the rotation delivery concept that used
before. It is provided fair share of water delivery among irrigation
districts and available water in the end of irrigation network,
although this system located in an end of irrigation networks in the
Nile Delta.
Abstract: Spray chilling using air-mist nozzles has received
much attention in the food processing industry because of the
benefits it has shown over forced air convection. These benefits
include an increase in the heat transfer coefficient and a reduction in
the water loss by the product during cooling. However, few studies
have simulated the heat transfer and aerodynamics phenomena of the
air-mist chilling process for optimal operating conditions. The study
provides insight into the optimal conditions for spray impaction, heat
transfer efficiency and control of surface flooding. A computational
fluid dynamics model using a two-phase flow composed of water
droplets injected with air is developed to simulate the air-mist
chilling of food products. The model takes into consideration
droplet-to-surface interaction, water-film accumulation and surface
runoff. The results of this study lead to a better understanding of the
heat transfer enhancement, water conservation, and to a clear
direction for the optimal design of air-mist chilling systems that can
be used in commercial applications in the food and meat processing
industries.
Abstract: Four phenylurea herbicides (isoproturon, chlortoluron, diuron and linuron) were dissolved in different water matrices in order to study their chemical degradation by using UV radiation, ozone and some advanced oxidation processes (UV/H2O2, O3/H2O2, Fenton reagent and the photo- Fenton system). The waters used were: ultra-pure water, a commercial mineral water, a groundwater and a surface water taken from a reservoir. Elimination levels were established for each herbicide and for several global quality parameters, and a kinetic study was performed in order to determine basic kinetic parameters of each reaction between the target phenylureas and these oxidizing systems.
Abstract: A major goal of any enterprise is to create a ratings
system of customer satisfaction, goods and services. It is obvious that
the company cannot change what is not measured. In order to get a
clearer picture of the preferences of the major consumer groups, this
stage should be based on extensive research, including a variety of
interviews and surveys. It is necessary to know the key benefits,
which determine customer satisfaction in the market segment, of the
properties of certain goods and services. It is important to estimate
the terms of these preferences from the viewpoint of the client. This
article discusses the importance of customer satisfaction, and ways of
assessing it.
Abstract: The paper shows how the CASMAS modeling language,
and its associated pervasive computing architecture, can be
used to facilitate continuity of care by providing members of patientcentered
communities of care with a support to cooperation and
knowledge sharing through the usage of electronic documents and
digital devices. We consider a scenario of clearly fragmented care to
show how proper mechanisms can be defined to facilitate a better
integration of practices and information across heterogeneous care
networks. The scenario is declined in terms of architectural components
and cooperation-oriented mechanisms that make the support
reactive to the evolution of the context where these communities
operate.
Abstract: An ordered porous antimony-doped tin oxide (ATO) film was successfully prepared using a simple coating process with colloidal templates. The facile production was effective when a combination of 16-nm ATO (as a model of an inorganic nanoparticle) and polystyrene (PS) spheres (as a model of the template) weresimply coated to produce a composite ATO/PS film. Heat treatment was then used to remove the PS and produce the porous film. The porous film with a spherical pore shape and a highly ordered porous structure could be obtained. A potential way for the control of pore size could be also achieved by changing initial template size. The theoretical explanation and mechanism of porous formation were also added, which would be important for the scaling-up prediction and estimation.
Abstract: Nowadays there are many methods for representing
knowledge such as semantic network, neural network, and conceptual
graphs. Nonetheless, these methods are not sufficiently efficient
when applied to perform and deduce on knowledge domains about
supporting in general education such as algebra, analysis or plane
geometry. This leads to the introduction of computational network
which is a useful tool for representation knowledge base, especially
for computational knowledge, especially knowledge domain about
general education. However, when dealing with a practical problem,
we often do not immediately find a new solution, but we search
related problems which have been solved before and then proposing
an appropriate solution for the problem. Besides that, when finding
related problems, we have to determine whether the result of them
can be used to solve the practical problem or not. In this paper, the
extension model of computational network has been presented. In this
model, Sample Problems, which are related problems, will be used
like the experience of human about practical problem, simulate the
way of human thinking, and give the good solution for the practical
problem faster and more effectively. This extension model is applied
to construct an automatic system for solving algebraic problems in
middle school.
Abstract: The compatibility of optical resonators with microfluidic systems may be relevant for chemical and biological applications. Here, a fluorescent-core microcavity (FCM) is investigated as a refractometric sensor for heavy oils. A high-index film of silicon quantum dots (QDs) was formed inside the capillary, supporting cylindrical fluorescence whispering gallery modes (WGMs). A set of standard refractive index oils was injected into a capillary, causing a shift of the WGM resonances toward longer wavelengths. A maximum sensitivity of 240 nm/RIU (refractive index unit) was found for a nominal oil index of 1.74. As well, a sensitivity of 22 nm/RIU was obtained for a lower index of 1.48, more typical of fuel hydrocarbons. Furthermore, the observed spectra and sensitivities were compared to theoretical predictions and reproduced via FDTD simulations, showing in general an excellent agreement. This work demonstrates the potential use of FCMs for oil sensing applications and the more generally for detecting liquid solutions with a high refractive index or high viscosity.
Abstract: Heat pipes are two-phase heat transfer devices with
high effective thermal conductivity. Due to the high heat transport
capacity, heat exchanger with heat pipes has become much smaller
than traditional heat exchangers in handling high heat fluxes. With
the working fluid in a heat pipe, heat can be absorbed on the
evaporator region and transported to the condenser region where the
vapour condenses releasing the heat to the cooling media. Heat pipe
technology has found increasing applications in enhancing the
thermal performance of heat exchangers in microelectranics, energy
saving in HVAC systems for operating rooms,surgery centers, hotels,
cleanrooms etc, temperature regulation systems for the human body
and other industrial sectors. Development activity in heat pipe and
thermosyphon technology in asia in recent years is surveyed. Some
new results obtained in Australia and other countries are also
included.