Abstract: The objective of this study is to investigate the
combustion in a pilot-ignited supercharged dual-fuel engine, fueled
with different types of gaseous fuels under various equivalence ratios.
It is found that if certain operating conditions are maintained,
conventional dual-fuel engine combustion mode can be transformed to
the combustion mode with the two-stage heat release. This mode of
combustion was called the PREMIER (PREmixed Mixture Ignition in
the End-gas Region) combustion. During PREMIER combustion,
initially, the combustion progresses as the premixed flame
propagation and then, due to the mixture autoignition in the end-gas
region, ahead of the propagating flame front, the transition occurs with
the rapid increase in the heat release rate.
Abstract: Minimum Quantity Lubrication (MQL) technique
obtained a significant attention in machining processes to reduce
environmental loads caused by usage of conventional cutting fluids.
Recently nanofluids are finding an extensive application in the field
of mechanical engineering because of their superior lubrication and
heat dissipation characteristics. This paper investigates the use of a
nanofluid under MQL mode to improve grinding characteristics of
Ti-6Al-4V alloy. Taguchi-s experimental design technique has been
used in the present investigation and a second order model has been
established to predict grinding forces and surface roughness.
Different concentrations of water based Al2O3 nanofluids were
applied in the grinding operation through MQL setup developed in
house and the results have been compared with those of conventional
coolant and pure water. Experimental results showed that grinding
forces reduced significantly when nano cutting fluid was used even at
low concentration of the nano particles and surface finish has been
found to improve with higher concentration of the nano particles.
Abstract: Iran is one of the greatest producers of date in the
world. However due to lack of information about its viscoelastic
properties, much of the production downgraded during harvesting
and postharvesting processes. In this study the effect of temperature
and moisture content of product were investigated on stress
relaxation characteristics. Therefore, the freshly harvested date
(kabkab) at tamar stage were put in controlled environment chamber
to obtain different temperature levels (25, 35, 45, and 55 0C) and
moisture contents (8.5, 8.7, 9.2, 15.3, 20, 32.2 %d.b.). A texture
analyzer TAXT2 (Stable Microsystems, UK) was used to apply
uniaxial compression tests. A chamber capable to control temperature
was designed and fabricated around the plunger of texture analyzer to
control the temperature during the experiment. As a new approach a
CCD camera (A4tech, 30 fps) was mounted on a cylindrical glass
probe to scan and record contact area between date and disk.
Afterwards, pictures were analyzed using image processing toolbox
of Matlab software. Individual date fruit was uniaxially compressed
at speed of 1 mm/s. The constant strain of 30% of thickness of date
was applied to the horizontally oriented fruit. To select a suitable
model for describing stress relaxation of date, experimental data were
fitted with three famous stress relaxation models including the
generalized Maxwell, Nussinovitch, and Pelege. The constant in
mentioned model were determined and correlated with temperature
and moisture content of product using non-linear regression analysis.
It was found that Generalized Maxwell and Nussinovitch models
appropriately describe viscoelastic characteristics of date fruits as
compared to Peleg mode.
Abstract: Dried tomato peel (DTP) was tested in vivo (n=10) in 42 week-old laying hens at rates of 0, 40, 70, 100 and 130g/kg DM feed. Laying hens were fed in group 120 g DM/day/animal for 26 days. After 21 days, feed intake was not affected after DTP incorporation (97% of the offered feed in the five groups). Laying rate was not significantly different after DTP incorporation at 4 and 10% from the control group. Egg yolk resulting from DTP-enriched diets, contained lower amounts of cholesterol (14 to 17mg/g) and triglyceride (188mg/g) compared to the control group (22 and 241 mg/g, respectively) (P
Abstract: Lean production (or lean management respectively)
gained popularity in several waves. The last three decades have been
filled with numerous attempts to apply these concepts in companies.
However, this has only been partially successful. The roots of lean
production can be traced back to Toyota-s just-in-time production.
This concept, which according to Womack-s, Jones- and Roos-
research at MIT was employed by Japanese car manufacturers,
became popular under its international names “lean production",
“lean-manufacturing" and was termed “Schlanke Produktion" in
Germany. This contribution shows a review about lean production in
Germany over the last thirty years: development, trial & error and
implementation as well.
Abstract: One of the biggest drawbacks of the wireless
environment is the limited bandwidth. However, the users sharing
this limited bandwidth have been increasing considerably. SDMA
technique which entails using directional antennas allows to increase
the capacity of a wireless network by separating users in the medium.
In this paper, it has been presented how the capacity can be enhanced
while the mean delay is reduced by using directional antennas in
wireless networks employing TDMA/FDD MAC. Computer
modeling and simulation of the wireless system studied are realized
using OPNET Modeler. Preliminary simulation results are presented
and the performance of the model using directional antennas is
evaluated and compared consistently with the one using
omnidirectional antennas.
Abstract: Intercropping is one of the sustainable agricultural
factors. The SPAD meter can be used to predict nitrogen index
reliably, it may also be a useful tool for assessing the relative impact
of weeds on crops. In order to study the effect of weeds on SPAD in
corn (Zea mays L.), sweet basil (Ocimum basilicum L.) and borage
(Borago officinalis L.) in intercropping system, a factorial experiment
was conducted in three replications in 2011. Experimental factors
were included intercropping of corn with sweet basil and borage in
different ratios (100:0, 75:25, 50:50, 25:75 and 0:100 corn: borage or
sweet basil) and weed infestation (weed control and weed
interference). The results showed that intercropping of corn with
sweet basil and borage increased the SPAD value of corn compare to
monoculture in weed interference condition. Sweet basil SPAD value
in weed control treatments (43.66) was more than weed interference
treatments (40.17). Corn could increase the borage SPAD value
compare to monoculture in weed interference treatments.
Abstract: Open Agent System platform based on High Level
Architecture is firstly proposed to support the application involving
heterogeneous agents. The basic idea is to develop different wrappers
for different agent systems, which are wrapped as federates to join a
federation. The platform is based on High Level Architecture and the
advantages for this open standard are naturally inherited, such as
system interoperability and reuse. Especially, the federal architecture
allows different federates to be heterogeneous so as to support the
integration of different agent systems. Furthermore, both implicit
communication and explicit communication between agents can be
supported. Then, as the wrapper RTI_JADE an example, the
components are discussed. Finally, the performance of RTI_JADE is
analyzed. The results show that RTI_JADE works very efficiently.
Abstract: In this paper we address a multi-objective scheduling problem for unrelated parallel machines. In unrelated parallel systems, the processing cost/time of a given job on different machines may vary. The objective of scheduling is to simultaneously determine the job-machine assignment and job sequencing on each machine. In such a way the total cost of the schedule is minimized. The cost function consists of three components, namely; machining cost, earliness/tardiness penalties and makespan related cost. Such scheduling problem is combinatorial in nature. Therefore, a Simulated Annealing approach is employed to provide good solutions within reasonable computational times. Computational results show that the proposed approach can efficiently solve such complicated problems.
Abstract: This paper discusses a new model of Islamic code of
ethics for directors. Several corporate scandals and local (example
Transmile and Megan Media) and overseas corporate (example
Parmalat and Enron) collapses show that the current corporate
governance and regulatory reform are unable to prevent these events
from recurring. Arguably, the code of ethics for directors is under
research and the current code of ethics only concentrates on binding
the work of the employee of the organization as a whole, without
specifically putting direct attention to the directors, the group of
people responsible for the performance of the company. This study
used a semi-structured interview survey of well-known Islamic
scholars such as the Mufti to develop the model. It is expected that
the outcome of the research is a comprehensive model of code of
ethics based on the Islamic principles that can be applied and used by
the company to construct a code of ethics for their directors.
Abstract: The software industry has been considered a critical
infrastructure for any nation. Several studies have indicated that
national competitiveness increasingly depends upon Information and
Communication Technology (ICT), and software is one of the major
components of ICT, important for both large and small enterprises.
Even though there has been strong growth in the software industry in
Thailand, the industry has faced many challenges and problems that
need to be resolved. For example, the amount of pirated software has
been rising, and Thailand still has a large gap in the digital divide.
Additionally, the adoption among SMEs has been slow. This paper
investigates various issues in the software industry in Thailand, using
information acquired through analysis of secondary sources,
observation, and focus groups. The results of this study can be used
as “lessons learned" for the development of the software industry in
any developing country.
Abstract: The protection issues in distribution systems with open and closed-loop are studied, and a generalized protection setting scheme based on the traditional over current protection theories is proposed to meet the new requirements. The setting method is expected to be easier realized using computer program, so that the on-line adaptive setting for coordination in distribution system can be implemented. An automatic setting program is created and several cases are taken into practice. The setting results are verified by the coordination curves of the protective devices which are plotted using MATLAB.
Abstract: Active vibration control is an important problem in
structures. The objective of active vibration control is to reduce the vibrations of a system by automatic modification of the system-s
structural response. In this paper, the modeling and design of a fast
output sampling feedback controller for a smart flexible beam system embedded with shear sensors and actuators for SISO system using
Timoshenko beam theory is proposed. FEM theory, Timoshenko beam theory and the state space techniques are used to model the
aluminum cantilever beam. For the SISO case, the beam is divided into 5 finite elements and the control actuator is placed at finite
element position 1, whereas the sensor is varied from position 2 to 5, i.e., from the nearby fixed end to the free end. Controllers are
designed using FOS method and the performance of the designed FOS controller is evaluated for vibration control for 4 SISO models
of the same plant. The effect of placing the sensor at different locations on the beam is observed and the performance of the
controller is evaluated for vibration control. Some of the limitations of the Euler-Bernoulli theory such as the neglection of shear and
axial displacement are being considered here, thus giving rise to an accurate beam model. Embedded shear sensors and actuators have
been considered in this paper instead of the surface mounted sensors
and actuators for vibration suppression because of lot of advantages. In controlling the vibration modes, the first three dominant modes of
vibration of the system are considered.
Abstract: Principle component analysis is often combined with
the state-of-art classification algorithms to recognize human faces.
However, principle component analysis can only capture these
features contributing to the global characteristics of data because it is a
global feature selection algorithm. It misses those features
contributing to the local characteristics of data because each principal
component only contains some levels of global characteristics of data.
In this study, we present a novel face recognition approach using
non-negative principal component analysis which is added with the
constraint of non-negative to improve data locality and contribute to
elucidating latent data structures. Experiments are performed on the
Cambridge ORL face database. We demonstrate the strong
performances of the algorithm in recognizing human faces in
comparison with PCA and NREMF approaches.
Abstract: This paper and its companion (Part 2) deal with
modeling and optimization of two NP-hard problems in production
planning of flexible manufacturing system (FMS), part type selection
problem and loading problem. The part type selection problem and
the loading problem are strongly related and heavily influence the
system-s efficiency and productivity. The complexity of the problems
is harder when flexibilities of operations such as the possibility of
operation processed on alternative machines with alternative tools are
considered. These problems have been modeled and solved
simultaneously by using real coded genetic algorithms (RCGA)
which uses an array of real numbers as chromosome representation.
These real numbers can be converted into part type sequence and
machines that are used to process the part types. This first part of the
papers focuses on the modeling of the problems and discussing how
the novel chromosome representation can be applied to solve the
problems. The second part will discuss the effectiveness of the
RCGA to solve various test bed problems.
Abstract: Improving performance measures in the construction
processes has been a major concern for managers and decision
makers in the industry. They seek for ways to recognize the key
factors which have the largest effect on the process. Identifying such
factors can guide them to focus on the right parts of the process in
order to gain the best possible result. In the present study design of
experiment (DOE) has been applied to a computer simulation model
of brick laying process to determine significant factors while
productivity has been chosen as the response of the experiment. To
this end, four controllable factors and their interaction have been
experimented and the best factor level has been calculated for each
one. The results indicate that three factors, namely, labor of brick,
labor of mortar and inter arrival time of mortar along with interaction
of labor of brick and labor of mortar are significant.
Abstract: Heart disease (HD) is a major cause of morbidity and mortality in the modern society. Medical diagnosis is an important but complicated task that should be performed accurately and efficiently and its automation would be very useful. All doctors are unfortunately not equally skilled in every sub specialty and they are in many places a scarce resource. A system for automated medical diagnosis would enhance medical care and reduce costs. In this paper, a new approach based on coactive neuro-fuzzy inference system (CANFIS) was presented for prediction of heart disease. The proposed CANFIS model combined the neural network adaptive capabilities and the fuzzy logic qualitative approach which is then integrated with genetic algorithm to diagnose the presence of the disease. The performances of the CANFIS model were evaluated in terms of training performances and classification accuracies and the results showed that the proposed CANFIS model has great potential in predicting the heart disease.
Abstract: Rotation or tilt present in an image capture by digital
means can be detected and corrected using Artificial Neural Network
(ANN) for application with a Face Recognition System (FRS). Principal
Component Analysis (PCA) features of faces at different angles
are used to train an ANN which detects the rotation for an input image
and corrected using a set of operations implemented using another
system based on ANN. The work also deals with the recognition
of human faces with features from the foreheads, eyes, nose and
mouths as decision support entities of the system configured using
a Generalized Feed Forward Artificial Neural Network (GFFANN).
These features are combined to provide a reinforced decision for
verification of a person-s identity despite illumination variations. The
complete system performing facial image rotation detection, correction
and recognition using re-enforced decision support provides a
success rate in the higher 90s.
Abstract: Owing to extensive use of hydrogen in refining or
petrochemical units, it is essential to manage hydrogen network in
order to make the most efficient utilization of hydrogen. On the other
hand, hydrogen is an important byproduct not properly used through
petrochemical complexes and mostly sent to the fuel system. A few
works have been reported in literature to improve hydrogen network
for petrochemical complexes. In this study a comprehensive analysis
is carried out on petrochemical units using a modified automated
targeting technique which is applied to determine the minimum
hydrogen consumption. Having applied the modified targeting
method in two petrochemical cases, the results showed a significant
reduction in required fresh hydrogen.
Abstract: Partial Discharge measurement is a very important
means of assessing the integrity of insulation systems in a High
Voltage apparatus. In compressed gas insulation systems, floating
particles can initiate partial discharge activities which adversely
affect the working of insulation. Partial Discharges below the
inception voltage also plays a crucial in damaging the integrity of
insulation over a period of time. This paper discusses the effect of
loose and fixed Copper and Nichrome wire particles on the PD
characteristics in SF6-N2 (10:90) gas mixtures at a pressure of
0.4MPa. The Partial Discharge statistical parameters and their
correlation to the observed results are discussed.