Abstract: We study the performance of compressed beamforming
weights feedback technique in generalized triangular decomposition
(GTD) based MIMO system. GTD is a beamforming technique that
enjoys QoS flexibility. The technique, however, will perform at its
optimum only when the full knowledge of channel state information
(CSI) is available at the transmitter. This would be impossible in
the real system, where there are channel estimation error and limited
feedback. We suggest a way to implement the quantized beamforming
weights feedback, which can significantly reduce the feedback data,
on GTD-based MIMO system and investigate the performance of
the system. Interestingly, we found that compressed beamforming
weights feedback does not degrade the BER performance of the
system at low input power, while the channel estimation error
and quantization do. For comparison, GTD is more sensitive to
compression and quantization, while SVD is more sensitive to the
channel estimation error. We also explore the performance of GTDbased
MU-MIMO system, and find that the BER performance starts
to degrade largely at around -20 dB channel estimation error.
Abstract: Studies on residential satisfaction have been actively
discussed under family house setting. However, limited studies have
been conducted on student residential satisfaction. This study is an
attempt to fill the research gap. It focuses on the influence of socioeconomic
on students- satisfaction with the universities- student
housing facilities. The students who stayed at the on-campus student
housing were the respondents. This study employed two-stage cluster
sampling method in classifying the respondents. Self-administered
questionnaires were distributed face-to-face to the students. In
general, it is confirmed that students- socio-economic backgrounds
have influence on the students- satisfaction with their housing
facilities. The main influential factors were the students- economic
status, sense of sharing, and ethnicity of their roommates.
Furthermore, this study could also provide a useful feedback for the
universities in order to improve their student housing facilities.
Abstract: The catalytic dehydroxylation of glycerol to propylene
glycol was investigated over Cu-ZnO/Al2O3 prepared by incipient
wetness impregnation (IWI) method with different purity feedstocks -
refined glycerol and technical grade glycerol. The main purpose is to
investigate the effects of feed impurities that cause the catalyst
deactivation. The prepared catalyst were tested for its catalytic
activity and selectivity in a continuous flow fixed bed reactor at 523
K, 500 psig, H2/feed molar ratio of 4 and WHSV of 3 h-1. The results
showed that conversion of refined glycerol and technical grade
glycerol at time on stream 6 hour are 99% and 71% and selectivity to
propylene glycol are 87% and 56% respectively. The ICP-EOS and
TPO results indicated that the cause of catalyst deactivation was the
amount of impurities in the feedstock. The higher amount of
impurities (especially Na and K) the lower catalytic activity.
Abstract: This paper analyzes the patterns of the Monte Carlo
data for a large number of variables and minterms, in order to
characterize the circuit path length behavior. We propose models
that are determined by training process of shortest path length
derived from a wide range of binary decision diagram (BDD)
simulations. The creation of the model was done use of feed forward
neural network (NN) modeling methodology. Experimental results
for ISCAS benchmark circuits show an RMS error of 0.102 for the
shortest path length complexity estimation predicted by the NN
model (NNM). Use of such a model can help reduce the time
complexity of very large scale integrated (VLSI) circuitries and
related computer-aided design (CAD) tools that use BDDs.
Abstract: In this paper we present an autoregressive model with
neural networks modeling and standard error backpropagation
algorithm training optimization in order to predict the gross domestic
product (GDP) growth rate of four countries. Specifically we propose
a kind of weighted regression, which can be used for econometric
purposes, where the initial inputs are multiplied by the neural
networks final optimum weights from input-hidden layer after the
training process. The forecasts are compared with those of the
ordinary autoregressive model and we conclude that the proposed
regression-s forecasting results outperform significant those of
autoregressive model in the out-of-sample period. The idea behind
this approach is to propose a parametric regression with weighted
variables in order to test for the statistical significance and the
magnitude of the estimated autoregressive coefficients and
simultaneously to estimate the forecasts.
Abstract: Recently, distributed generation technologies have received much attention for the potential energy savings and reliability assurances that might be achieved as a result of their widespread adoption. Fueling the attention have been the possibilities of international agreements to reduce greenhouse gas emissions, electricity sector restructuring, high power reliability requirements for certain activities, and concern about easing transmission and distribution capacity bottlenecks and congestion. So it is necessary that impact of these kinds of generators on distribution feeder reconfiguration would be investigated. This paper presents an approach for distribution reconfiguration considering Distributed Generators (DGs). The objective function is summation of electrical power losses A Tabu search optimization is used to solve the optimal operation problem. The approach is tested on a real distribution feeder.
Abstract: In this paper we consider a nonlinear feedback control
called augmented automatic choosing control (AACC) using the
gradient optimization automatic choosing functions for nonlinear
systems. Constant terms which arise from sectionwise linearization
of a given nonlinear system are treated as coefficients of a stable
zero dynamics. Parameters included in the control are suboptimally
selected by expanding a stable region in the sense of Lyapunov
with the aid of the genetic algorithm. This approach is applied to
a field excitation control problem of power system to demonstrate
the splendidness of the AACC. Simulation results show that the new
controller can improve performance remarkably well.
Abstract: Partial oxidation (POX) of light hydrocarbons (e.g.
methane) is occurred in the first part of the autothermal reformer
(ATR). The results of the detailed modeling of the reformer based on
the thermodynamic model of the POX and 1D heterogeneous
catalytic model for the fixed bed section are considered here.
According to the results, the overall performance of the ATR can be
improved by changing the important feed parameters.
Abstract: This paper presents a novel CMOS four-transistor
SRAM cell for very high density and low power embedded SRAM
applications as well as for stand-alone SRAM applications. This cell
retains its data with leakage current and positive feedback without
refresh cycle. The new cell size is 20% smaller than a conventional
six-transistor cell using same design rules. Also proposed cell uses
two word-lines and one pair bit-line. Read operation perform from
one side of cell, and write operation perform from another side of
cell, and swing voltage reduced on word-lines thus dynamic power
during read/write operation reduced. The fabrication process is fully
compatible with high-performance CMOS logic technologies,
because there is no need to integrate a poly-Si resistor or a TFT load.
HSPICE simulation in standard 0.25μm CMOS technology confirms
all results obtained from this paper.
Abstract: In North America, Most power distribution systems
employ a four-wire multi-grounded neutral (MGN) design. This paper has explained the inherent characteristics of multi-grounded three-phase four-wire distribution systems under unbalanced
situations. As a result, the mechanism of voltage swell and voltage sag in MGN feeders becomes difficult to understand. The simulation
tool that has been used in this paper is MATLAB under Windows software. In this paper the equivalent model of a full-scale multigrounded
distribution system implemented by MATLAB is
introduced. The results are expected to help utility engineers to understand the impact of MGN on distribution system operations.
Abstract: Vacuum membrane distillation (VMD) process can be
used for water purification or the desalination of salt water. The
process simply consists of a flat sheet hydrophobic micro porous
PTFE membrane and diaphragm vacuum pump without a condenser
for the water recovery or trap. The feed was used aqueous NaCl
solution. The VMD experiments were performed to evaluate the heat
and mass transfer coefficient of the boundary layer in a membrane
module. The only operating parameters are feed inlet temperature,
and feed flow rate were investigated. The permeate flux was strongly
affected by the feed inlet temperature, feed flow rate, and boundary
layer heat transfer coefficient. Since lowering the temperature
polarization coefficient is essential enhance the process performance
considerable and maximizing the heat transfer coefficient for
maximizes the mass flux of distillate water. In this paper, the results
of VMD experiments are used to measure the boundary layer heat
transfer coefficient, and the experimental results are used to reevaluate
the empirical constants in the Dittus- Boelter equation.
Abstract: This paper features the mathematical modeling of a single input single output based Timoshenko smart beam. Further, this mathematical model is used to design a multirate output feedback based discrete sliding mode controller using Bartoszewicz law to suppress the flexural vibrations. The first 2 dominant vibratory modes is retained. Here, an application of the discrete sliding mode control in smart systems is presented. The algorithm uses a fast output sampling based sliding mode control strategy that would avoid the use of switching in the control input and hence avoids chattering. This method does not need the measurement of the system states for feedback as it makes use of only the output samples for designing the controller. Thus, this methodology is more practical and easy to implement.
Abstract: This paper presents key challenges reported by a
group of Australian undergraduate Physical Education students in
conducting a program for persons with an intellectual disability.
Strategies adopted to address these challenges are presented together
with representative feedback given by the Physical Education
students at the completion of the program. The significance of the
program’s findings is summarized.
Abstract: It is well known that a linear dynamic system including
a delay will exhibit limit cycle oscillations when a bang-bang sensor
is used in the feedback loop of a PID controller. A similar behaviour
occurs when a delayed feedback signal is used to train a neural
network. This paper develops a method of predicting this behaviour
by linearizing the system, which can be shown to behave in a manner
similar to an integral controller. Using this procedure, it is possible
to predict the characteristics of the neural network driven limit cycle
to varying degrees of accuracy, depending on the information known
about the system. An application is also presented: the intelligent
control of a spark ignition engine.
Abstract: The continuity in the electric supply of the electric installations is becoming one of the main requirements of the electric supply network (generation, transmission, and distribution of the electric energy). The achievement of this requirement depends from one side on the structure of the electric network and on the other side on the avaibility of the reserve source provided to maintain the supply in case of failure of the principal one. The avaibility of supply does not only depends on the reliability parameters of the both sources (principal and reserve) but it also depends on the reliability of the circuit breaker which plays the role of interlocking the reserve source in case of failure of the principal one. In addition, the principal source being under operation, its control can be ideal and sure, however, for the reserve source being in stop, a preventive maintenances which proceed on time intervals (periodicity) and for well defined lengths of time are envisaged, so that this source will always available in case of the principal source failure. The choice of the periodicity of preventive maintenance of the source of reserve influences directly the reliability of the electric feeder system In this work and on the basis of the semi- markovian's processes, the influence of the time of interlocking the reserve source upon the reliability of an industrial electric network is studied and is given the optimal time of interlocking the reserve source in case of failure the principal one, also the influence of the periodicity of the preventive maintenance of the source of reserve is studied and is given the optimal periodicity.
Abstract: Carbon disulfide is widely used for the production of
viscose rayon, rubber, and other organic materials and it is a
feedstock for the synthesis of sulfuric acid. The objective of this
paper is to analyze possibilities for efficient production of CS2 from
sour natural gas reformation (H2SMR) (2H2S+CH4 =CS2 +4H2) .
Also, the effect of H2S to CH4 feed ratio and reaction temperature on
carbon disulfide production is investigated numerically in a
reforming reactor. The chemical reaction model is based on an
assumed Probability Density Function (PDF) parameterized by the
mean and variance of mixture fraction and β-PDF shape. The results
show that the major factors influencing CS2 production are reactor
temperature. The yield of carbon disulfide increases with increasing
H2S to CH4 feed gas ratio (H2S/CH4≤4). Also the yield of C(s)
increases with increasing temperature until the temperature reaches
to 1000°K, and then due to increase of CS2 production and
consumption of C(s), yield of C(s) drops with further increase in the
temperature. The predicted CH4 and H2S conversion and yield of
carbon disulfide are in good agreement with result of Huang and TRaissi.
Abstract: Dynamic Causal Modeling (DCM) functional
Magnetic Resonance Imaging (fMRI) is a promising technique to
study the connectivity among brain regions and effects of stimuli
through modeling neuronal interactions from time-series
neuroimaging. The aim of this study is to study characteristics of a
mirror neuron system (MNS) in elderly group (age: 60-70 years old).
Twenty volunteers were MRI scanned with visual stimuli to study a
functional brain network. DCM was employed to determine the
mechanism of mirror neuron effects. The results revealed major
activated areas including precentral gyrus, inferior parietal lobule,
inferior occipital gyrus, and supplementary motor area. When visual
stimuli were presented, the feed-forward connectivity from visual
area to conjunction area was increased and forwarded to motor area.
Moreover, the connectivity from the conjunction areas to premotor
area was also increased. Such findings can be useful for future
diagnostic process for elderly with diseases such as Parkinson-s and
Alzheimer-s.
Abstract: Repetitive control and feedback dithering modulation
are applied to a single-phase voltage source inverter, with an aim to
eliminate harmonics and stabilize the inverter under load variations.
The proposed control and modulation scheme comprise multiple loops
of feedback, which helps improve inverter performance and
robustness. Experimental results show that the designed inverter
exhibits very low distortion at its output with THD of about 0.3%
under different load variations.
Abstract: The three-time-scale plant model of a wind power
generator, including a wind turbine, a flexible vertical shaft, a Variable
Inertia Flywheel (VIF) module, an Active Magnetic Bearing (AMB)
unit and the applied wind sequence, is constructed. In order to make
the wind power generator be still able to operate as the spindle speed
exceeds its rated speed, the VIF is equipped so that the spindle speed
can be appropriately slowed down once any stronger wind field is
exerted. To prevent any potential damage due to collision by shaft
against conventional bearings, the AMB unit is proposed to regulate
the shaft position deviation. By singular perturbation order-reduction
technique, a lower-order plant model can be established for the
synthesis of feedback controller. Two major system parameter
uncertainties, an additive uncertainty and a multiplicative uncertainty,
are constituted by the wind turbine and the VIF respectively.
Frequency Shaping Sliding Mode Control (FSSMC) loop is proposed
to account for these uncertainties and suppress the unmodeled
higher-order plant dynamics. At last, the efficacy of the FSSMC is
verified by intensive computer and experimental simulations for
regulation on position deviation of the shaft and counter-balance of
unpredictable wind disturbance.
Abstract: In this paper, we consider the almost periodic solutions of a discrete cooperation system with feedback controls. Assuming that the coefficients in the system are almost periodic sequences, we obtain the existence and uniqueness of the almost periodic solution which is uniformly asymptotically stable.