Abstract: The study site was located in Ratchaburi Province,
Thailand. Four experimental plots in dry dipterocarp forest (DDF)
and four plots in mixed deciduous forest (MDF) were set up to
estimate the above-ground biomass of tree, sapling and bamboo. The
allometry equations were used to investigate above-ground biomass
of these vegetation. Seedling and other understory were determined
using direct harvesting method. Carbon storage in above-ground
biomass was calculated based on IPCC 2006.
The results showed that the above-ground biomass of DDF at
20-40% slope,
Abstract: This paper presents a tested research concept that
implements a complex evolutionary algorithm, genetic algorithm
(GA), in a multi-microcontroller environment. Parallel Distributed
Genetic Algorithm (PDGA) is employed in adaptive beam forming
technique to reduce power usage of adaptive antenna at WCDMA
base station. Adaptive antenna has dynamic beam that requires more
advanced beam forming algorithm such as genetic algorithm which
requires heavy computation and memory space. Microcontrollers are
low resource platforms that are normally not associated with GAs,
which are typically resource intensive. The aim of this project was to
design a cooperative multiprocessor system by expanding the role of
small scale PIC microcontrollers to optimize WCDMA base station
transmitter power. Implementation results have shown that PDGA
multi-microcontroller system returned optimal transmitted power
compared to conventional GA.
Abstract: This paper deals with behavior and capacity of
punching shear force for flat slabs produced from steel fiber
reinforced self compacting concrete (SFRSCC) by application
nonlinear finite element method. Nonlinear finite element analysis on
nine slab specimens was achieved by using ANSYS software. A
general description of the finite element method, theoretical modeling
of concrete and reinforcement are presented. The nonlinear finite
element analysis program ANSYS is utilized owing to its capabilities
to predict either the response of reinforced concrete slabs in the post
elastic range or the ultimate strength of a flat slabs produced from
steel fiber reinforced self compacting concrete (SFRSCC). In order to
verify the analytical model used in this research using test results of
the experimental data, the finite element analysis were performed
then a parametric study of the effect ratio of flexural reinforcement,
ratio of the upper reinforcement, and volume fraction of steel fibers
were investigated. A comparison between the experimental results
and those predicted by the existing models are presented. Results and
conclusions may be useful for designers, have been raised, and
represented.
Abstract: This paper presented the results of an experimental
investigation into the axial fatigue behavior of a 5086 aluminum
alloy which have several notch-aspect ratios a0/c0 and notch
thickness ratio a/t with semi-elliptical surface cracks. Tests were
conducted in la b air for stress levels of 50 % of their yield
strength. Experiments were carried out for various notch to
thickness ratios. Crack growth rates of test specimens both in
surface and depth directions were determined by using die
penetration method. Fuzzy Logic method was used to predict the
deep direction crack growth because the dept of the crack is
considerably difficult to measure.
Abstract: This paper reports on the results of experimental investigations on the performance of a jet pump operated under selected primary flows to optimize the related parameters. For this purpose a two-phase flow jet pump was used employing various profiles of nozzles as the primary device which was designed, fabricated and used along with the combination of mixing tube and diffuser. The profiles employed were circular, conical, and elliptical. The diameter of the nozzle used was 4 mm. The area ratio of the jet pump was 0.16. The test facility created for this purpose was an open loop continuous circulation system. Performance of the jet pump was obtained as iso-efficiency curves on characteristic curves drawn for various water flow rates. To perform the suction capability, evacuation test was conducted at best efficiency point for all the profiles.
Abstract: Application of synthetic antioxidants such as tertbutylhydroquinon
(TBHQ), in spite of their efficiency, is questioned
because of their possible carcinogenic effect. The purpose of this
study was application of mixtures of natural antioxidants that provide
the best oxidative stability for margarine. Antioxidant treatments
included 10 various mixtures (F1- F10) containing 100-500ppm
tocopherol mixture (Toc), 100-200ppm ascorbyl palmitate (AP), 100-
200ppm rosemary extract (Ros) and 1000ppm lecithin(Lec) along
with a control or F0 (with no antioxidant) and F11 with 120ppm
TBHQ. The effect of antioxidant mixtures on the stability of
margarine samples during oven test (60°C), rancimat test at 110°C
and storage at 4°C was evaluated. Final ranking of natural antioxidant
mixtures was as follows: F2,F10>F5,F9>F8>F1,F3,F4>F6, F7.
Considering the results of this research and ranking criteria,
F2(200ppmAp + 200ppmRos) and F10(200ppmRos + 200ppmToc
+1000ppmLec) were recommended as substitutes for TBHQ to
maintain the quality and increase the shelf-life of margarine.
Abstract: Multilevel inverters supplied from equal and constant
dc sources almost don-t exist in practical applications. The variation
of the dc sources affects the values of the switching angles required
for each specific harmonic profile, as well as increases the difficulty
of the harmonic elimination-s equations. This paper presents an
extremely fast optimal solution of harmonic elimination of multilevel
inverters with non-equal dc sources using Tanaka's fuzzy linear
regression formulation. A set of mathematical equations describing
the general output waveform of the multilevel inverter with nonequal
dc sources is formulated. Fuzzy linear regression is then
employed to compute the optimal solution set of switching angles.
Abstract: To estimate the risks of dam failure phenomenon, it is necessary to understand this phenomenon and the involved governing factors. Overtopping and piping are the two main reasons of earthdam failures. In the piping context, the piping is determined as a phenomenon which is occurred between two phases, the water liquid and the solid soil. In this investigation, the onset of piping and its development, as well as the movement of water in soil, are numerically approached. In this regard, a one-dimensional numerical model based on the mass-conserving finite-volume method is developed and applied in order to simulate the piping phenomenon in a continuous circular tunnel of given initial length and radius, located between upstream and downstream. The simulation result includes the time-variations of radius along the tunnel until the radius value reaches its critical and the piping phenomenon converts to overtopping.
Abstract: Recently, majors of doctors are divided into terribly lots of detailed areas. However, it is actually not a rare case that a doctor has a patient who is not in his/her major. He/She must judge an assessment and make a medical treatment plan for this patient. According to our investigation, conventional approaches such as image diagnosis cooperation are insufficient. This paper proposes an 'Assessment / Medical Treatment Plan Consulting System'. We have implemented a pilot system based on our proposition. Its effectiveness is clarified by an evaluation.
Abstract:
Innovation is becoming more and more important in
modern society. There are a lot of researches on different kinds of
innovation but marketing innovation is one kind of innovation that
has not been studied frequently before. Marketing innovation is
defined as a new way in which companies can market themselves to
potential or existing customers.
The study shows some key elements for marketing innovation that
are worth paying attention to when implementing marketing
innovation projects. Examples of such key elements are: paying
attention to the neglected market, suitable market segmentatio
reliable market information, public relationship, increased customer
value, combination of market factors, explore different marketing
channels and the use of technology in combination with what? Beside
the key elements for marketing innovation, we also present some
risks that may occur, such as cost, market uncertainty, information
leakage, imitation and overdependence on experience.
By proposing a set of indicators to measure marketing innovation,
the article offers solutions for marketing innovation implementation
so that any organization can achieve optimal results.
Abstract: In this paper, a method based on Non-Dominated
Sorting Genetic Algorithm (NSGA) has been presented for the Volt /
Var control in power distribution systems with dispersed generation
(DG). Genetic algorithm approach is used due to its broad
applicability, ease of use and high accuracy. The proposed method is
better suited for volt/var control problems. A multi-objective
optimization problem has been formulated for the volt/var control of
the distribution system. The non-dominated sorting genetic algorithm
based method proposed in this paper, alleviates the problem of tuning
the weighting factors required in solving the multi-objective volt/var
control optimization problems. Based on the simulation studies
carried out on the distribution system, the proposed scheme has been
found to be simple, accurate and easy to apply to solve the multiobjective
volt/var control optimization problem of the distribution
system with dispersed generation.
Abstract: This study is aimed to investigate feasibility of the
aerobic biological process to treat oily wastewater from palm oil food
industry. Effect of aeration and sludge concentrations are studied.
Raw sludge and raw wastewater was mixed and acclimatized for five
days in a stirred tank reactor. The aeration rate (no aeration, low;
1.5L/min and high rate; 2L/min) and sludge concentration (3675,
7350, and 11025mg/L of VSS) were varied. Responses of process
were pH, COD, oil and grease, VSS, and PHB content. It was found
that the treatment can remove 85.1 to 97.1 % of COD and remove
12.9 to 54.8% of oil & grease. The PHB yield was found to be within
0.15% to 2.4% as PHB/VSS ratio and 0.01% to 0.12% as PHB/COD
removed. The higher aeration results a high COD removal and oil &
grease removal, while experiment without aeration gives better PHB
yield. Higher sludge concentrations (11025mg/L VSS) give higher
removal of oil & grease while moderate sludge concentration
(7350mg/L VSS) give better result in COD removal. Higher PHB
yield is obtained in low sludge concentration (3675mg/L).
Abstract: The main objective of this paper is to provide an efficient tool for delineating brain tumors in three-dimensional magnetic resonance images and set up compression-transmit schemes to distribute result to the remote doctor. To achieve this goal, we use basically a level-sets approach to delineating brain tumors in threedimensional. Then introduce a new compression and transmission plan of 3D brain structures based for the meshes simplification, adapted for time to the specific needs of the telemedicine and to the capacities restricted by wireless network communication. We present here the main stages of our system, and preliminary results which are very encouraging for clinical practice.
Abstract: Estimation of natural frequency of structures is very
important and isn-t usually calculated simply and sometimes
complicated. Lack of knowledge about that caused hard damage and
hazardous effects.
In this paper, with using from two different models in FEM
method and based on hydrodynamic mass of fluids, natural frequency
of an especial bearing (Fig. 1) in an electric field (or, a periodic
force) is calculated in different stiffness and different geometric. In
final, the results of two models and analytical solution are compared.
Abstract: A climate dependent model is proposed to simulate
the population of Aedes aegypti mosquito. In developing the model,
average temperature of Shah Alam, Malaysia was used to determine
the development rate of each stage of the life cycle of mosquito.
Rainfall dependent function was proposed to simulate the hatching
rate of the eggs under several assumptions. The proposed transition
matrix was obtained and used to simulate the population of eggs,
larvae, pupae and adults mosquito. It was found that the peak of
mosquito abundance comes during a relatively dry period following a
heavy rainfall. In addition, lag time between the peaks of mosquito
abundance and dengue fever cases in Shah Alam was estimated.
Abstract: In this investigation, anatase TiO2 thin films were
grown by radio frequency magnetron sputtering on glass substrates at
a high sputtering pressure and room temperature. The anatase films
were then annealed at 300-600 °C in air for a period of 1 hour. To
examine the structure and morphology of the films, X-ray diffraction
(XRD) and atomic force microscopy (AFM) methods were used
respectively. From X-ray diffraction patterns of the TiO2 films, it was
found that the as-deposited film showed some differences compared
with the annealed films and the intensities of the peaks of the
crystalline phase increased with the increase of annealing
temperature. From AFM images, the distinct variations in the
morphology of the thin films were also observed. The optical
constants were characterized using the transmission spectra of the
films obtained by UV-VIS-IR spectrophotometer. Besides, optical
thickness of the film deposited at room temperature was calculated
and cross-checked by taking a cross-sectional image through SEM.
The optical band gaps were evaluated through Tauc model. It was
observed that TiO2 films produced at room temperatures exhibited
high visible transmittance and transmittance decreased slightly with
the increase of annealing temperatures. The films were found to be
crystalline having anatase phase. The refractive index of the films
was found from 2.31-2.35 in the visible range. The extinction
coefficient was nearly zero in the visible range and was found to
increase with annealing temperature. The allowed indirect optical
band gap of the films was estimated to be in the range from 3.39 to
3.42 eV which showed a small variation. The allowed direct band
gap was found to increase from 3.67 to 3.72 eV. The porosity was
also found to decrease at a higher annealing temperature making the
film compact and dense.
Abstract: In recent years, copulas have become very popular in
financial research and actuarial science as they are more flexible in
modelling the co-movements and relationships of risk factors as compared
to the conventional linear correlation coefficient by Pearson.
However, a precise estimation of the copula parameters is vital in
order to correctly capture the (possibly nonlinear) dependence structure
and joint tail events. In this study, we employ two optimization
heuristics, namely Differential Evolution and Threshold Accepting to
tackle the parameter estimation of multivariate t distribution models
in the EML approach. Since the evolutionary optimizer does not rely
on gradient search, the EML approach can be applied to estimation of
more complicated copula models such as high-dimensional copulas.
Our experimental study shows that the proposed method provides
more robust and more accurate estimates as compared to the IFM
approach.
Abstract: The present study was designed to demonstrate the seasonal variations in physico-chemical parameters of fish farm at Govt. Nursery Unit, Muzaffargarh, Department of Fisheries Govt. of Punjab, Pakistan for a period of eight months from January to August 2008. Water samples were collected on fifteen days basis and have been analyzed for estimation of Air temperature, Water temperature, Light penetration, pH, Total dissolved oxygen, Clouds, Carbonates, Bicarbonates, Total carbonates, Total dissolved solids, Chlorides, Calcium and Hardness. Seasonal fluctuations were observed in all the physico-chemical parameters of fish farm. The overall physicochemical parameters of fish pond water remained within the tolerable range throughout the study period.
Abstract: In this paper, we present a technical and an economic
assessment of several sources of renewable energy in Saudi Arabia;
mainly solar, wind, hydro and biomass. We analyze the
environmental and climatic conditions in relation to these sources
and give an overview of some of the existing clean energy
technologies. Using standardized cost and efficiency data, we carry
out a cost benefit analysis to understand the economic factors
influencing the sustainability of energy production from renewable
sources in light of the energy cost and demand in the Saudi market.
Finally, we take a look at the Saudi petroleum industry and the
existing sources of conventional energy and assess the potential of
building a successful market for renewable energy under the
constraints imposed by the flow of subsidized cheap oil. We show
that while some renewable energy resources are well suited for
distributed or grid connected generation in the kingdom, their
viability is greatly undercut by the well developed and well
capitalized oil industry.
Abstract: This study experimentally and numerically investigates
motor cooling performance. The motor consists of a centrifugal fan,
two axial fans, a shaft, a stator, a rotor and a heat exchanger with 637
cooling tubes. The pressure rise-flow rate (P-Q) performance curves of
the cooling fans at 1800 rpm are tested using a test apparatus
complying with the Chinese National Standard (CNS) 2726.
Compared with the experimental measurements, the numerical
analysis results show that the P-Q performance curves of the axial fan
and centrifugal fan can be estimated within about 2% and 6%,
respectively. By using the simplified model, setting up the heat
exchanger and stator as porous media, the flow field in the motor is
calculated. By using the results of the flow field near the rotor and
stator, and subjecting the heat generation rate as a boundary condition,
the temperature distributions of the stator and rotor are also calculated.
The simulation results show that the calculated temperature of the
stator winding near the axial fans is lower by about 5% than the
measured value, and the calculated temperature of the stator core
located at the center of the stator is about 1% higher than the measured
value. Besides, discussion is made to improve the motor cooling
performance.