Abstract: This study utilizes a frequency domain approach over
the period of 1996 to 2013 to examine the causal relationship between
governance and economic growth in ten Asian countries, which have
different levels of democracy; classified as “Free”, “Partly Free”, and
“Not Free” countries. The empirical results show that there is no
Granger causality running from governance to economic growth in
“Not Free” countries and “Partly Free” countries with the exception of
Singapore. As for “Free” countries such as South Korea and Taiwan,
there is a one-way causality running from governance to economic
growth. The findings of this study indicate that policy makers in South
Korea, Taiwan, and Singapore could use governance index to improve
their predictions of the future economic growth.
Abstract: This work presents an improved single fiber pull-out
test for fiber/matrix interface characterization. This test has been
used to study the Inter-Facial Shear Strength ‘IFSS’ of hemp fibers
reinforced polypropylene (PP). For this aim, the fiber diameter
has been carefully measured using a tomography inspired method.
The fiber section contour can then be approximated by a circle
or a polygon. The results show that the IFSS is overestimated if
the circular approximation is used. The Influence of the molding
temperature on the IFSS has also been studied. We find that a molding
temperature of 183◦C leads to better interfacial properties. Above or
below this temperature the interface strength is reduced.
Abstract: Distillery spentwash contains high chemical oxygen
demand (COD), biological oxygen demand (BOD), color, total
dissolved solids (TDS) and other contaminants even after biological
treatment. The effluent can’t be discharged as such in the surface
water bodies or land without further treatment. Reverse osmosis (RO)
treatment plants have been installed in many of the distilleries at
tertiary level in many of the distilleries in India, but are not properly
working due to fouling problem which is caused by the presence of
high concentration of organic matter and other contaminants in
biologically treated spentwash. In order to make the membrane
treatment a proven and reliable technology, proper pre-treatment is
mandatory. In the present study, ultra-filtration (UF) for pretreatment
of RO at tertiary stage has been performed. Operating
parameters namely initial pH (pHo: 2–10), trans-membrane pressure
(TMP: 4-20 bars) and temperature (T: 15-43°C) were used for
conducting experiments with UF system. Experiments were
optimized at different operating parameters in terms of COD, color,
TDS and TOC removal by using response surface methodology
(RSM) with central composite design. The results showed that
removal of COD, color and TDS was 62%, 93.5% and 75.5%
respectively, with UF, at optimized conditions with increased
permeate flux from 17.5 l/m2/h (RO) to 38 l/m2/h (UF-RO). The
performance of the RO system was greatly improved both in term of
pollutant removal as well as water recovery.
Abstract: Biodiesel production from vegetable oil will produce
glycerol as by-product about 10% of the biodiesel production. The
amount of glycerol that was produced needed alternative way to
handling immediately so as to not become the waste that polluted
environment. One of the solutions was to process glycerol to
polyglycidyl nitrate (PGN). PGN is synthesized from glycerol by
three-step reactions i.e. nitration of glycerol, cyclization of 13-
dinitroglycerine and polymerization of glycosyl nitrate. Optimum
condition of nitration of glycerol with nitric acid has not been known.
Thermodynamic feasibility should be done before run experiments in
the laboratory. The aim of this study was to determine the parameters
those affect nitration of glycerol and nitric acid and chose the
operation condition. Many parameters were simulated to verify its
possibility to experiment under conditions which would get the
highest conversion of 1, 3-dinitroglycerine and which was the ideal
condition to get it. The parameters that need to be studied to obtain
the highest conversion of 1, 3-dinitroglycerine were mol ratio of
nitric acid/glycerol, reaction temperature, mol ratio of
glycerol/dichloromethane and pressure. The highest conversion was
obtained in the range of mol ratio of nitric acid /glycerol between 2/1
– 5/1, reaction temperature of 5-25oC and pressure of 1 atm. The
parameters that need to be studied further to obtain the highest
conversion of 1.3 DNG are mol ratio of nitric acid/glycerol and
reaction temperature.
Abstract: In this study, to clarify the effectiveness of an
aluminum/chromium/tungsten-based-coated tool for cutting sintered
steel, tool wear was experimentally investigated. The sintered steel
was turned with the (Al60,Cr25,W15)N-, (Al60,Cr25,W15)(C,N)- and
(Al64,Cr28,W8)(C,N)-coated cemented carbide tools according to the
physical vapor deposition (PVD) method. Moreover, the tool wear of
the aluminum/chromium/tungsten-based-coated item was compared
with that of the (Al,Cr)N coated tool. Furthermore, to clarify the tool
wear mechanism of the aluminum/chromium/tungsten-coating film for
cutting sintered steel, Scanning Electron Microscope observation and
Energy Dispersive x-ray Spectroscopy mapping analysis were
conducted on the abraded surface. The following results were
obtained: (1) The wear progress of the (Al64,Cr28,W8)(C,N)-coated
tool was the slowest among that of the five coated tools. (2) Adding
carbon (C) to the aluminum/chromium/tungsten-based-coating film
was effective for improving the wear-resistance. (3) The main wear
mechanism of the (Al60,Cr25,W15)N-, the (Al60,Cr25,W15)(C,N)-
and the (Al64,Cr28,W8)(C,N)-coating films was abrasive wear.
Abstract: The economic use and ease of construction of profiled
deck composite slab is marred with the complex and un-economic
strength verification required for the serviceability and general safety
considerations. Beside these, albeit factors such as shear span length,
deck geometries and mechanical frictions greatly influence the
longitudinal shear strength, that determines the ultimate strength of
profiled deck composite slab, and number of methods available for its
determination; partial shear and slope-intercept are the two methods
according to Euro-code 4 provision. However, the complexity
associated with shear behavior of profiled deck composite slab, the
use of these methods in determining the load carrying capacities of
such slab yields different and conflicting values. This couple with the
time and cost constraint associated with the strength verification is a
source of concern that draws more attentions nowadays, the issue is
critical. Treating some of these known shear strength influencing
factors as random variables, the load carrying capacity violation of
profiled deck composite slab from the use of the two-methods
defined according to Euro-code 4 are determined using reliability
approach, and comparatively studied. The study reveals safety values
from the use of m-k method shows good standing compared with that
from the partial shear method.
Abstract: Bicycle Level of Service (BLOS) is a measure for
evaluating street conditions for cyclists. Currently, various methods
are proposed for BLOS. These analytical methods however have
some drawbacks: they usually assume cyclists as users that can share
street facilities with motorized vehicles, it is not easy to link them to
design process and they are not easy to follow. In addition, they only
support a narrow range of cycling facilities and may not be applicable
for all situations. Along this, the current paper introduces various
effective design factors for bicycle-friendly streets. This study
considers cyclists as users of streets who have special needs and
facilities. Therefore, the key factors that influence BLOS based on
different cycling facilities that are proposed by developed guidelines
and literature are identified. The combination of these factors
presents a complete set of effective design factors for bicycle-friendly
streets. In addition, the weight of each factor in existing BLOS
models is estimated and these effective factors are ranked based on
these weights. These factors and their weights can be used in further
studies to propose special bicycle-friendly street design model.
Abstract: The main parameters affecting the workability are the
water content, particle size, and the total surface of the grains, as long
as the mixing water begins by wetting the surface of the grains and
then fills the voids between the grains to form entrapped water, the
quantity of water remaining is called free water. The aim of this study is to undertake a fractal approach through
the relationship between the concrete formulation parameters and
workability. To develop this approach a series of concrete taken from
the literature was investigated by varying formulation parameters
such as G/S, the quantity of cement C and the quantity of water W. We also call another model as the model of water layer thickness
and model of paste layer thickness to judge their relevance, hence the
following results: the relevance of the water layer thickness model is
considered as a relevant when there is a variation in the water
quantity. The model of the paste layer thickness is only applicable if
we considered that the paste is made with the grain value Dmax =
2.85: value from which we see a stability of the model.
Abstract: The efficient and economic allocation of resources is
one main goal in the field of production planning and control.
Nowadays, a new variable gains in importance throughout the
planning process: Energy. Energy-efficiency has already been widely
discussed in literature, but with a strong focus on reducing the overall
amount of energy used in production. This paper provides a brief
systematic approach, how energy-supply-orientation can be used for
an energy-cost-efficient production planning and thus combining the
idea of energy-efficiency and energy-flexibility.
Abstract: Superabsorbent polymers received much attention and
are used in many fields because of their superior characters to
traditional absorbents, e.g., sponge and cotton. So, it is very
important but challenging to prepare highly and fast-swelling
superabsorbents. A reliable, efficient and low-cost technique for
removing heavy metal ions from wastewater is the adsorption using
bio-adsorbents obtained from biological materials, such as
polysaccharides-based hydrogels superabsorbents. In this study, novel multi-functional superabsorbent composites
type semi-interpenetrating polymer networks (Semi-IPNs) were
prepared via graft polymerization of acrylamide onto chitosan
backbone in presence of gelatin, CTS-g-PAAm/Ge, using potassium
persulfate and N,N’-methylene bisacrylamide as initiator and
crosslinker, respectively. These hydrogels were also partially
hydrolyzed to achieve superabsorbents with ampholytic properties
and uppermost swelling capacity. The formation of the grafted
network was evidenced by Fourier Transform Infrared Spectroscopy
(ATR-FTIR) and Thermogravimetric Analysis (TGA). The porous
structures were observed by Scanning Electron Microscope (SEM).
From TGA analysis, it was concluded that the incorporation of the Ge
in the CTS-g-PAAm network has marginally affected its thermal
stability. The effect of gelatin content on the swelling capacities of
these superabsorbent composites was examined in various media
(distilled water, saline and pH-solutions). The water absorbency was
enhanced by adding Ge in the network, where the optimum value was
reached at 2 wt. % of Ge. Their hydrolysis has not only greatly
optimized their absorption capacity but also improved the swelling
kinetic.These materials have also showed reswelling ability. We
believe that these super-absorbing materials would be very effective
for the adsorption of harmful metal ions from wastewater.
Abstract: This paper describes a new approach which can be
used to interpret the experimental creep deformation data obtained
from miniaturized thin plate bending specimen test to the
corresponding uniaxial data based on an inversed application of the
reference stress method. The geometry of the thin plate is fully
defined by the span of the support, l, the width, b, and the thickness,
d. Firstly, analytical solutions for the steady-state, load-line creep
deformation rate of the thin plates for a Norton’s power law under
plane stress (b→0) and plane strain (b→∞) conditions were obtained,
from which it can be seen that the load-line deformation rate of the
thin plate under plane-stress conditions is much higher than that
under the plane-strain conditions. Since analytical solution is not
available for the plates with random b-values, finite element (FE)
analyses are used to obtain the solutions. Based on the FE results
obtained for various b/l ratios and creep exponent, n, as well as the
analytical solutions under plane stress and plane strain conditions, an
approximate, numerical solutions for the deformation rate are
obtained by curve fitting. Using these solutions, a reference stress
method is utilised to establish the conversion relationships between
the applied load and the equivalent uniaxial stress and between the
creep deformations of thin plate and the equivalent uniaxial creep
strains. Finally, the accuracy of the empirical solution was assessed
by using a set of “theoretical” experimental data.
Abstract: In this study, nuclear magnetic resonance
spectroscopy and nuclear quadrupole resonance spectroscopy
parameters of 14N (Nitrogen in imidazole ring) in N–H…O hydrogen
bonding for Histidine hydrochloride monohydrate were calculated via
density functional theory. We considered a five-molecule model
system of Histidine hydrochloride monohydrate. Also we examined
the trends of environmental effect on hydrogen bonds as well as
cooperativity. The functional used in this research is M06-2X which
is a good functional and the obtained results has shown good
agreement with experimental data. This functional was applied to
calculate the NMR and NQR parameters. Some correlations among
NBO parameters, NMR and NQR parameters have been studied
which have shown the existence of strong correlations among them.
Furthermore, the geometry optimization has been performed using
M062X/6-31++G(d,p) method. In addition, in order to study
cooperativity and changes in structural parameters, along with
increase in cluster size, natural bond orbitals have been employed.
Abstract: EEG correlates of mathematical and trait anxiety level
were studied in 52 healthy Russian-speakers during execution of
error-recognition tasks with lexical, arithmetic and algebraic
conditions. Event-related spectral perturbations were used as a
measure of brain activity. The ERSP plots revealed alpha/beta
desynchronizations within a 500-3000 ms interval after task onset
and slow-wave synchronization within an interval of 150-350 ms.
Amplitudes of these intervals reflected the accuracy of error
recognition, and were differently associated with the three conditions.
The correlates of anxiety were found in theta (4-8 Hz) and beta2 (16-
20 Hz) frequency bands. In theta band the effects of mathematical
anxiety were stronger expressed in lexical, than in arithmetic and
algebraic condition. The mathematical anxiety effects in theta band
were associated with differences between anterior and posterior
cortical areas, whereas the effects of trait anxiety were associated
with inter-hemispherical differences. In beta1 and beta2 bands effects
of trait and mathematical anxiety were directed oppositely. The trait
anxiety was associated with increase of amplitude of
desynchronization, whereas the mathematical anxiety was associated
with decrease of this amplitude. The effect of mathematical anxiety
in beta2 band was insignificant for lexical condition but was the
strongest in algebraic condition. EEG correlates of anxiety in theta
band could be interpreted as indexes of task emotionality, whereas
the reaction in beta2 band is related to tension of intellectual
resources.
Abstract: Artificial neural networks have gained a lot of interest
as empirical models for their powerful representational capacity,
multi input and output mapping characteristics. In fact, most feedforward
networks with nonlinear nodal functions have been proved to
be universal approximates. In this paper, we propose a new
supervised method for color image classification based on selforganizing
feature maps (SOFM). This algorithm is based on
competitive learning. The method partitions the input space using
self-organizing feature maps to introduce the concept of local
neighborhoods. Our image classification system entered into RGB
image. Experiments with simulated data showed that separability of
classes increased when increasing training time. In additional, the
result shows proposed algorithms are effective for color image
classification.
Abstract: This paper investigates the parametric stability of an
axially moving web subjected to non-uniform in-plane edge
excitations on two opposite, simply-supported edges. The web is
modeled as a viscoelastic plate whose constitutive relation obeys the
Kelvin-Voigt model, and the in-plane edge excitations are expressed
as the sum of a static tension and a periodical perturbation. Due to the
in-plane edge excitations, the moving plate may bring about
parametric instability under certain situations. First, the in-plane
stresses of the plate due to the non-uniform edge excitations are
determined by solving the in-plane forced vibration problem. Then,
the dependence on the spatial coordinates in the equation of transverse
motion is eliminated by the generalized Galerkin method, which
results in a set of discretized system equations in time. Finally, the
method of multiple scales is utilized to solve the set of system
equations analytically if the periodical perturbation of the in-plane
edge excitations is much smaller as compared with the static tension of
the plate, from which the stability boundaries of the moving plate are
obtained. Numerical results reveal that only combination resonances
of the summed-type appear under the in-plane edge excitations
considered in this work.
Abstract: Aurèsregion is one of the arid and semi-arid areas that
have suffered climate crises and overexploitation of natural resources
they have led to significant land degradation. The use of remote sensing data allowed us to analyze the land and
its spatiotemporal changes in the Aurès between 1987 and 2013, for
this work, we adopted a method of analysis based on the exploitation
of the images satellite Landsat TM 1987 and Landsat OLI 2013, from
the supervised classification likelihood coupled with field surveys of
the mission of May and September of 2013. Using ENVI EX software by the superposition of the ground cover
maps from 1987 and 2013, one can extract a spatial map change of
different land cover units. The results show that between 1987 and
2013 vegetation has suffered negative changes are the significant
degradation of forests and steppe rangelands, and sandy soils and
bare land recorded a considerable increase. The spatial change map land cover units between 1987 and 2013
allows us to understand the extensive or regressive orientation of
vegetation and soil, this map shows that dense forests give his place
to clear forests and steppe vegetation develops from a degraded forest
vegetation and bare, sandy soils earn big steppe surfaces that explain
its remarkable extension.
The analysis of remote sensing data highlights the profound
changes in our environment over time and quantitative monitoring of
the risk of desertification.
Abstract: In this paper, influence of harmonics on medium
voltage distribution system of Bogazici Electricity Distribution Inc.
(BEDAS) which takes place at Istanbul/Turkey is investigated. A ring
network consisting of residential loads is taken into account for this
study. Real system parameters and measurement results are used for
simulations. Also, probable working conditions of the system are
analyzed for 50%, 75%, and 100% loading of transformers with
similar harmonic contents. Results of the study are exhibited the
influence of nonlinear loads on %THDV, P.F. and technical losses of
the medium voltage distribution system.
Abstract: This paper presents a state-of-the-art survey of the
operations research models developed for internal audit planning.
Two alternative approaches have been followed in the literature for
audit planning: (1) identifying the optimal audit frequency; and (2)
determining the optimal audit resource allocation. The first approach
identifies the elapsed time between two successive audits, which can
be presented as the optimal number of audits in a given planning
horizon, or the optimal number of transactions after which an audit
should be performed. It also includes the optimal audit schedule. The
second approach determines the optimal allocation of audit frequency
among all auditable units in the firm. In our review, we discuss both
the deterministic and probabilistic models developed for audit
planning. In addition, game theory models are reviewed to find the
optimal auditing strategy based on the interactions between the
auditors and the clients.
Abstract: Accurate forecasting of fresh produce demand is one
the challenges faced by Small Medium Enterprise (SME)
wholesalers. This paper is an attempt to understand the cause for the
high level of variability such as weather, holidays etc., in demand of
SME wholesalers. Therefore, understanding the significance of
unidentified factors may improve the forecasting accuracy. This
paper presents the current literature on the factors used to predict
demand and the existing forecasting techniques of short shelf life
products. It then investigates a variety of internal and external
possible factors, some of which is not used by other researchers in the
demand prediction process. The results presented in this paper are
further analysed using a number of techniques to minimize noise in
the data. For the analysis past sales data (January 2009 to May 2014)
from a UK based SME wholesaler is used and the results presented
are limited to product ‘Milk’ focused on café’s in derby. The
correlation analysis is done to check the dependencies of variability
factor on the actual demand. Further PCA analysis is done to
understand the significance of factors identified using correlation.
The PCA results suggest that the cloud cover, weather summary and
temperature are the most significant factors that can be used in
forecasting the demand. The correlation of the above three factors
increased relative to monthly and becomes more stable compared to
the weekly and daily demand.
Abstract: High Voltage Direct Current (HVDC) power
transmission is employed to move large amounts of electric power.
There are several possibilities to enhance the transient stability in a
power system. One adequate option is by using the high
controllability of the HVDC if HVDC is available in the system. This
paper presents a control technique for HVDC to enhance the transient
stability. The strategy controls the power through the HVDC to help
make the system more transient stable during disturbances. Loss of
synchronism is prevented by quickly producing sufficient
decelerating energy to counteract accelerating energy gained during.
In this study, the power flow in the HVDC link is modulated with the
addition of an auxiliary signal to the current reference of the rectifier
firing angle controller. This modulation control signal is derived from
speed deviation signal of the generator utilizing a PD controller; the
utilization of a PD controller is suitable because it has the property of
fast response. The effectiveness of the proposed controller is
demonstrated with a SMIB test system.