Abstract: Ammonia nitrogen is one of the most hazardous
water pollutants, discharging into water receptors through industrial
effluents. Negative environmental impacts of such chemical species
in hydrosphere include accelerated eutrophication, water toxicity and
harming the aquatics. Natural zeolite clinoptilolite has very high
selectivity & capacity for ammonium cation sorption. It occurs in
high abundances and rich mines of this zeolite exist in different parts
of Iran and thus are available more cheaply and with different sizing.
The aim of this study is to investigate ammonia nitrogen removal
over this natural sorbent from real samples of high polluted
wastewater discharging from a fertilizer producing plant. The
experimental results showed that this natural sorbent without even
any pre treatment system & with the same particle size available in
Iranian markets has still high capability & selectivity in ammonia
nitrogen removal both in batch and continuous tests.
Abstract: This paper proposes a new optimal feedback controller
for voltage source converters VSC's, for current regulated voltage
source converters, which allows compensate the harmonics of current
produced by nonlinear loads and load reactive power. The aim of the
present paper is to describe a novel switching signal generation
technique called optimal controller which guarantees that the injected
currents follow the reference currents determined by the
compensation strategy, with the smallest possible tracking error and
fixed switching frequency. It is compared with well-known
hysteresis current controller HCC. The validity of presented method
and its comparison with HCC is studied through simulation results.
Abstract: A cross-sectional study was carried out to determine the prevalence, species characterization and associated risk factors with Eimeria (E.) in sheep of district Toba Tek Singh from April, 2009 to March, 2010. Of the total 486 faecal samples examined for Eimeria, 209 (43%) were found infected with five species of Eimeria. Amongst the identified species of Eimeria, E. ovinoidalis was the commonest one (48.32%), followed in order by E. ahsata, E. intricata, E. parva and E. faurei with prevalence of 45.45, 28.71, 24.40 and 19.14 percent respectively. Peak prevalence was observed in August. Wet season (rainy and post-rainy) was found to be favourable for Eimeria infection. Lambs had significantly higher prevalence (P < 0.05) of Eimeria than adults. Similarly higher prevalence of Eimeria was observed in female as compared to male. Among management and husbandry practices; watering system, housing system, floor type and herd size strongly influenced the prevalence of Eimeria. Coccidiosis was more prevalent in closed housing system, non-cemented floor type, pond watered animals and larger herds (P < 0.05) as compared to open housing system, partially cemented floor type, tap watered animals and smaller herds respectively. Feeding system, breed and body condition of animals were not found as risk factors (P>0.05) influencing prevalence of Eimeria.
Abstract: Supply chain management has become more
challenging with the emerging trend of globalization and
sustainability. Lately, research related to perishable products supply
chains, in particular agricultural food products, has emerged. This is
attributed to the additional complexity of managing this type of
supply chains with the recently increased concern of public health,
food quality, food safety, demand and price variability, and the
limited lifetime of these products. Inventory management for agrifood
supply chains is of vital importance due to the product
perishability and customers- strive for quality. This paper
concentrates on developing a simulation model of a real life case
study of a two echelon production-distribution system for agri-food
products. The objective is to improve a set of performance measures
by developing a simulation model that helps in evaluating and
analysing the performance of these supply chains. Simulation results
showed that it can help in improving overall system performance.
Abstract: Extreme temperature of several stations in Malaysia is
modelled by fitting the monthly maximum to the Generalized
Extreme Value (GEV) distribution. The Mann-Kendall (MK) test
suggests a non-stationary model. Two models are considered for
stations with trend and the Likelihood Ratio test is used to determine
the best-fitting model. Results show that half of the stations favour a
model which is linear for the location parameters. The return level is
the level of events (maximum temperature) which is expected to be
exceeded once, on average, in a given number of years, is obtained.
Abstract: A biosensor based on glucose oxidase (GOx) immobilized onto nanoparticles zirconium oxide with polyethylene nanocomposite for glucose monitoring has been designed. The CTAB/PEG/ZrO2/GOx nanocomposite was deposited onto screen printed carbon paste (SPCE) electrode via spin coating technique. The properties of CTAB/PEG/ZrO2/GOx were study using scanning electron microscopy (SEM). The SPE modified with the CTAB/PEG/ZrO2/GOx showed electrocatalytical response to the oxidation of glucose when ferrocene carboxaldehyde was used as an artificial redox mediator, which was studied by cyclic voltammetry (CV). Several parameters such as working potential, effect of pH and effect of ZrO2/PEG layers that governed the analytical performance of the biosensor, have been studied. The biosensor was applied to detect glucose with a linear range of 0.4 to 2.0 mmol L−1 with good repetability and reproducibility.
Abstract: Antimicrobial (AM) starch-based films were
developed by incorporating chitosan and lauric acid as antimicrobial
agent into starch-based film. Chitosan has wide range of applications
as a biomaterial, but barriers still exist to its broader use due to its
physical and chemical limitations. In this work, a series of
starch/chitosan (SC) blend films containing 8% of lauric acid was
prepared by casting method. The structure of the film was
characterized by Fourier transform infrared spectroscopy (FTIR), Xray
diffraction (XRD), and scanning electron microscopy (SEM).
The results indicated that there were strong interactions were present
between the hydroxyl groups of starch and the amino groups of
chitosan resulting in a good miscibility between starch and chitosan
in the blend films. Physical properties and optical properties of the
AM starch-based film were evaluated. The AM starch-based films
incorporated with chitosan and lauric acid showed an improvement in
water vapour transmission rate (WVTR) and addition of starch
content provided more transparent films while the yellowness of the
film attributed to the higher chitosan content. The improvement in
water barrier properties was mainly attributed to the hydrophobicity
of lauric acid and optimum chitosan or starch content. AM starch
based film also showed excellent oxygen barrier. Obtaining films
with good oxygen permeability would be an indication of the
potential use of these antimicrobial packaging as a natural packaging
and an alternative packaging to the synthetic polymer to protect food
from oxidation reactions
Abstract: This study analyses the perceptions of secondary
school students about the accounting profession in Malaysia. Fifty
five form three and form four students who are taking
accounting/commerce subjects were met. Individual-s perception
data were collected through questionnaires. The results at the
secondary school level suggest that the stereotypical negative image
of the accountant ends, with students expressing the positive view of
the work of an accountant. There were also gender differences in
perceiving the accounting profession. Overall, the results of the study
suggest that we are now in line in projecting positive and accurate
perceptions of the accounting profession to secondary school
students.
Abstract: For many industrial applications plate heat
exchangers are demonstrating a large superiority over the
other types of heat exchangers. The efficiency of such a
device depends on numerous factors the effect of which needs
to be analysed and accurately evaluated.
In this paper we present a theoretical analysis of a cocurrent
plate heat exchanger and the results of its numerical
simulation.
Knowing the hot and the cold fluid streams inlet temperatures,
the respective heat capacities mCp
and the value of the
overall heat transfer coefficient, a 1-D mathematical model
based on the steady flow energy balance for a differential
length of the device is developed resulting in a set of N first
order differential equations with boundary conditions where N
is the number of channels.For specific heat exchanger
geometry and operational parameters, the problem is
numerically solved using the shooting method.
The simulation allows the prediction of the temperature
map in the heat exchanger and hence, the evaluation of its
performances. A parametric analysis is performed to evaluate
the influence of the R-parameter on the e-NTU values. For
practical purposes effectiveness-NTU graphs are elaborated
for specific heat exchanger geometry and different operating
conditions.
Abstract: In this paper, several different types of natural gas liquefaction cycle. First, two processes are a cascade process with two staged compression were designed and simulated. These include Inter-cooler which is consisted to Propane, Ethylene and Methane cycle, and also, liquid-gas heat exchanger is applied to between of methane and ethylene cycles (process2) and between of ethylene and propane (process2). Also, these cycles are compared with two staged cascade process using only a Inter-cooler (process1). The COP of process2 and process3 showed about 13.99% and 6.95% higher than process1, respectively. Also, the yield efficiency of LNG improved comparing with process1 by 13.99% lower specific power. Additionally, C3MR process are simulated and compared with Process 2.
Abstract: This paper presented a theoretical and numerical investigation of the Compact Antenna Test Range (CATR) equipped with Super Hybrid Modulated Segmented Exponential Serrations (SHMSES). The investigation was based on diffraction theory and, more specifically, the Fresnel diffraction formulation. The CATR provides uniform illumination within the Fresnel region to test antenna. Application of serrated edges has been shown to be a good method to control diffraction at the edges of the reflectors. However, in order to get some insight into the positive effect of serrated edges a less rigorous analysis technique known as Physical Optics (PO) may be used. Ripple free and enhanced quiet zone width are observed for specific values of width and height modulation factors per serrations. The performance of SHMSE serrated reflector is evaluated in order to observe the effects of edge diffraction on the test zone fields.
Abstract: Vinegar or sour wine is a product of alcoholic and
subsequent acetous fermentation of sugary precursors derived from
several fruits or starchy substrates. This delicious food additive and
supplement contains not less than 4 grams of acetic acid in 100 cubic
centimeters at 20°C. Among the large number of bacteria that are
able to produce acetic acid, only few genera are used in vinegar
industry most significant of which are Acetobacter and
Gluconobacter. In this research we isolated and identified an
Acetobacter strain from Iranian apricot, a very delicious and sensitive
summer fruit to decay, we gathered from fruit's stores in Isfahan,
Iran. The main culture media we used were Carr, GYC, Frateur and
an industrial medium for vinegar production. We isolated this strain
using a novel miniature fermentor we made at Pars Yeema
Biotechnologists Co., Isfahan Science and Technology Town (ISTT),
Isfahan, Iran. The microscopic examinations of isolated strain from
Iranian apricot showed gram negative rods to cocobacilli. Their
catalase reaction was positive and oxidase reaction was negative and
could ferment ethanol to acetic acid. Also it showed an acceptable
growth in 5%, 7% and 9% ethanol concentrations at 30°C using
modified Carr media after 24, 48 and 96 hours incubation
respectively. According to its tolerance against high concentrations of
ethanol after four days incubation and its high acetic acid production,
8.53%, after 144 hours, this strain could be considered as a suitable
industrial strain for a production of a new type of vinegar, apricot
vinegar, with a new and delicious taste. In conclusion this is the first
report of isolation and identification of an Acetobacter strain from
Iranian apricot with a very good tolerance against high ethanol
concentrations as well as high acetic acid productivity in an
acceptable incubation period of time industrially. This strain could be
used in vinegar industry to convert apricot spoilage to a beneficiary
product and mentioned characteristics have made it as an amenable
strain in food and agricultural biotechnology.
Abstract: Among the various cooling processes in industrial
applications such as: electronic devices, heat exchangers, gas
turbines, etc. Gas turbine blades cooling is the most challenging one.
One of the most common practices is using ribbed wall because of
the boundary layer excitation and therefore making the ultimate
cooling. Vortex formation between rib and channel wall will result in
a complicated behavior of flow regime. At the other hand, selecting
the most efficient method for capturing the best results comparing to
experimental works would be a fascinating issue. In this paper 4
common methods in turbulence modeling: standard k-e, rationalized
k-e with enhanced wall boundary layer treatment, k-w and RSM
(Reynolds stress model) are employed to a square ribbed channel to
investigate the separation and thermal behavior of the flow in the
channel. Finally all results from different methods which are used in
this paper will be compared with experimental data available in
literature to ensure the numerical method accuracy.
Abstract: Over Current Relays (OCRs) and Directional Over Current Relays (DOCRs) are widely used for the radial protection and ring sub transmission protection systems and for distribution systems. All previous work formulates the DOCR coordination problem either as a Non-Linear Programming (NLP) for TDS and Ip or as a Linear Programming (LP) for TDS using recently a social behavior (Particle Swarm Optimization techniques) introduced to the work. In this paper, a Modified Particle Swarm Optimization (MPSO) technique is discussed for the optimal settings of DOCRs in power systems as a Non-Linear Programming problem for finding Ip values of the relays and for finding the TDS setting as a linear programming problem. The calculation of the Time Dial Setting (TDS) and the pickup current (Ip) setting of the relays is the core of the coordination study. PSO technique is considered as realistic and powerful solution schemes to obtain the global or quasi global optimum in optimization problem.
Abstract: While the explosive increase in information published
on the Web, researchers have to filter information when searching for
conference related information. To make it easier for users to search
related information, this paper uses Topic Maps and social information
to implement ontology since ontology can provide the formalisms and
knowledge structuring for comprehensive and transportable machine
understanding that digital information requires. Besides enhancing
information in Topic Maps, this paper proposes a method of
constructing research Topic Maps considering social information.
First, extract conference data from the web. Then extract conference
topics and the relationships between them through the proposed
method. Finally visualize it for users to search and browse. This paper
uses ontology, containing abundant of knowledge hierarchy structure,
to facilitate researchers getting useful search results. However, most
previous ontology construction methods didn-t take “people" into
account. So this paper also analyzes the social information which helps
researchers find the possibilities of cooperation/combination as well as
associations between research topics, and tries to offer better results.
Abstract: Continuous measurements and multivariate methods are applied in researching the effects of energy consumption on indoor air quality (IAQ) in a Finnish one-family house. Measured data used in this study was collected continuously in a house in Kuopio, Eastern Finland, during fourteen months long period. Consumption parameters measured were the consumptions of district heat, electricity and water. Indoor parameters gathered were temperature, relative humidity (RH), the concentrations of carbon dioxide (CO2) and carbon monoxide (CO) and differential air pressure. In this study, self-organizing map (SOM) and Sammon's mapping were applied to resolve the effects of energy consumption on indoor air quality. Namely, the SOM was qualified as a suitable method having a property to summarize the multivariable dependencies into easily observable two-dimensional map. Accompanying that, the Sammon's mapping method was used to cluster pre-processed data to find similarities of the variables, expressing distances and groups in the data. The methods used were able to distinguish 7 different clusters characterizing indoor air quality and energy efficiency in the study house. The results indicate, that the cost implications in euros of heating and electricity energy vary according to the differential pressure, concentration of carbon dioxide, temperature and season.
Abstract: The issue of human anthropology took an important
role in the last epochs and still hasn-t lost its importance. Scientists of
different countries were interested in investigating the appearance of
human being and the idea of life after death. While writing this article
we noticed that scientists who made research in this issue, despite of
the different countries and different epochs in which they lived, had
similarities in their opinions. In given article we wrote great Kazakh
poet AbaiKunanbayev-s philosophical view to the problem of human
anthropology.
Abstract: This work presents a study on the abrasive water jet
(AWJ) machining. An explicit finite element analysis (FEA) of
single abrasive particle impact on stainless steel 1.4304 (AISI 304) is
conducted. The abrasive water jet machining is modeled by FEA
software ABAQUS/CAE. Shapes of craters in FEM simulation
results were used and compared with the previous experimental and
FEM works by means of crater sphericity. The influence of impact
angle and particle velocity was observed. Adaptive mesh domain is
used to model the impact zone. Results are in good agreement with
those obtained from the experimental and FEM simulation. The
crater-s depth is also obtained for different impact angle and abrasive
particle velocities.
Abstract: The treatment of the industrial wastewater can be
particularly difficult in the presence of toxic compounds. Excessive
concentration of Chromium in soluble form is toxic to a wide variety
of living organisms. Biological removal of heavy metals using natural
and genetically engineered microorganisms has aroused great interest
because of its lower impact on the environment. Ralston
metallidurans, formerly known as Alcaligenes eutrophus is a LProteobacterium
colonizing industrial wastewater with a high content
of heavy metals. Tris-buffered mineral salt medium was used for
growing Alcaligenes eutrophus AE104 (pEBZ141). The cells were
cultivated for 18 h at 30 oC in Tris-buffered mineral salt medium
containing 3 mM disodium sulphate and 46 mM sodium gluconate as
the carbon source. The cells were harvested by centrifugation,
washed, and suspended in 10 mM Tris HCl, pH 7.0, containing 46
mM sodium gluconate, and 5 mM Chromium. Interaction among
induction of chr resistance determinant, and chromate reduction have
been demonstrated. Results of this study show that the above bacteria
can be very useful for bioremediation of chromium from industrial
wastewater.
Abstract: Signal processing applications which are iterative in
nature are best represented by data flow graphs (DFG). In these
applications, the maximum sampling frequency is dependent on the
topology of the DFG, the cyclic dependencies in particular. The
determination of the iteration bound, which is the reciprocal of the
maximum sampling frequency, is critical in the process of hardware
implementation of signal processing applications. In this paper, a
novel technique to compute the iteration bound is proposed. This
technique is different from all previously proposed techniques, in the
sense that it is based on the natural flow of tokens into the DFG
rather than the topology of the graph. The proposed algorithm has
lower run-time complexity than all known algorithms. The
performance of the proposed algorithm is illustrated through
analytical analysis of the time complexity, as well as through
simulation of some benchmark problems.