Abstract: In present study, two kinds of thermal power plant ashes; one the fly ash and the other waste ash are mixed with adhesive tragacanth and cement to produce new composite materials. 48 new samples are produced by varying the percentages of the fly ash, waste ash, cement and tragacanth. The new samples are subjected to some tests to find out their properties such as thermal conductivity, compressive strength, tensile strength and sucking capability of water. It is found that; the thermal conductivity decreases with increasing amount of tragacanth in the mixture. The compressive, tensile strength increases when the rate of tragacanth is up to 1%, whilst as the amount of tragacanth increases up to 1.5%, the compressive, tensile strength decreases slightly. The rate of water absorption of samples was more than 30%. From this result, it is concluded that these materials can not be used as external plaster or internal plaster material that faces to water. They can be used in internal plaster unless touching water and they can be used as cover plaster under roof and riprap material in sandwich panels. It is also found that, these materials can be cut with saw, drilled with screw and painted with any kind of paint.
Abstract: If a possibility distribution and a probability distribution
are describing values x of one and the same system or process
x(t), can they relate to each other? Though in general the possibility
and probability distributions might be not connected at all, we
can assume that in some particular cases there is an association linked
them.
In the presented paper, we consider distributions of bloodstream
concentrations of physiologically active substances and propose that
the probability to observe a concentration x of a substance X can be
produced from the possibility of the event X = x .
The proposed assumptions and resulted theoretical distributions
are tested against the data obtained from various panel studies of the
bloodstream concentrations of the different physiologically active
substances in patients and healthy adults as well.
Abstract: When choosing marketing strategies for international markets, one of the factors that should be considered is the cultural differences that exist among consumers in different countries. If the branding strategy has to be contextual and in tune with the culture, then the brand positioning variables has to interact, adapt and respond to the cultural variables in which the brand is operating. This study provides an overview of the relevance of culture in the development of an effective branding strategy in the international business environment. Hence, the main objective of this study is to provide a managerial framework for developing strategies for cross cultural brand management. The framework is useful because it incorporates the variables that are important in the competitiveness of fast food enterprises irrespective of their size. It provides practical, proactive and result oriented analysis that will help fast food firms augment their strategies in the international fast food markets. The proposed framework will enable managers understand the intricacies involved in branding in the global fast food industry and decrease the use of 'trial and error' when entering into unfamiliar markets.
Abstract: State-dependent Riccati equation based controllers are
becoming increasingly popular because of having attractive
properties like optimality, stability and robustness. This paper focuses
on the design of a roll autopilot for a fin stabilized and canard
controlled 122mm artillery rocket using state-dependent Riccati
equation technique. Initial spin is imparted to rocket during launch
and it quickly decays due to straight tail fins. After the spin phase, the
roll orientation of rocket is brought to zero with the canard deflection
commands generated by the roll autopilot. Roll autopilot has been
developed by considering uncoupled roll, pitch and yaw channels.
The canard actuator is modeled as a second-order nonlinear system.
Elements of the state weighing matrix for Riccati equation have been
chosen to be state dependent to exploit the design flexibility offered
by the Riccati equation technique. Simulation results under varying
conditions of flight demonstrate the wide operating range of the
proposed autopilot.
Abstract: In this paper, a new BiCMOS CCII and CCCII,
capable of operate at ±0.5V and having wide dynamic range with
achieved bandwidth of 480MHz and 430MHz respectively have been
proposed. The structures have been found to be insensitive to the
threshold voltage variations. The proposed circuits are suitable for
implementation using 0.25μm BiCMOS technology. Pspice
simulations confirm the performance of the proposed structures.
Abstract: Social interest and demand on Home-Network has
been increasing greatly. Although various services are being
introduced to respond to such demands, they can cause serious
security problems when linked to the open network such as Internet.
This paper reviews the security requirements to protect the service
users with assumption that the Home-Network environment is
connected to Internet and then proposes the security model based on
the requirement. The proposed security model can satisfy most of the
requirements and further can be dynamically applied to the future
ubiquitous Home-Networks.
Abstract: A new paradigm for software design and development models software by its business process, translates the model into a process execution language, and has it run by a supporting execution engine. This process-oriented paradigm promotes modeling of software by less technical users or business analysts as well as rapid development. Since business process models may be shared by different organizations and sometimes even by different business domains, it is interesting to apply a technique used in traditional software component technology to design reusable business processes. This paper discusses an approach to apply a technique for software component fabrication to the design of process-oriented software units, called process components. These process components result from decomposing a business process of a particular application domain into subprocesses with an aim that the process components can be reusable in different process-based software models. The approach is quantitative because the quality of process component design is measured from technical features of the process components. The approach is also strategic because the measured quality is determined against business-oriented component management goals. A software tool has been developed to measure how good a process component design is, according to the required managerial goals and comparing to other designs. We also discuss how we benefit from reusable process components.
Abstract: The effect of chemical treatment in CdCl2 and thermal
annealing in 400°C, on the defect structures of potentially useful
ZnS\CdS solar cell thin films deposited onto quartz substrate and
prepared by vacuum deposition method was studied using the
Thermoluminesence (TL) techniques. A series of electron and hole
traps are found in the various deposited samples studied. After
annealing, however, it was observed that the intensity and activation
energy of TL signal increases with loss of the low temperature
electron traps.
Abstract: Intelligent systems based on machine learning
techniques, such as classification, clustering, are gaining wide spread
popularity in real world applications. This paper presents work on
developing a software system for predicting crop yield, for example
oil-palm yield, from climate and plantation data. At the core of our
system is a method for unsupervised partitioning of data for finding
spatio-temporal patterns in climate data using kernel methods which
offer strength to deal with complex data. This work gets inspiration
from the notion that a non-linear data transformation into some high
dimensional feature space increases the possibility of linear
separability of the patterns in the transformed space. Therefore, it
simplifies exploration of the associated structure in the data. Kernel
methods implicitly perform a non-linear mapping of the input data
into a high dimensional feature space by replacing the inner products
with an appropriate positive definite function. In this paper we
present a robust weighted kernel k-means algorithm incorporating
spatial constraints for clustering the data. The proposed algorithm
can effectively handle noise, outliers and auto-correlation in the
spatial data, for effective and efficient data analysis by exploring
patterns and structures in the data, and thus can be used for
predicting oil-palm yield by analyzing various factors affecting the
yield.
Abstract: This paper presents the experimental results of
discharge current phenomena on various humidity, temperature,
pressure and pollutant conditions of epoxy resin specimen. The
leakage distance of specimen was 3 cm, that it was supplied by high
voltage. The polluted condition was given with NaCl artificial
pollutant. The conducted measurements were discharge current and
applied voltage. The specimen was put in a hermetically sealed
chamber, and the current waveforms were analyzed with FFT.
The result indicated that on discharge condition, the fifth
harmonics still had dominant, rather than third one. The third
harmonics tent to be appeared on low pressure heavily polluted
condition, and followed by high humidity heavily polluted condition.
On the heavily polluted specimen, the peaks discharge current points
would be high and more frequent. Nevertheless, the specimen still
had capacitive property. Besides that, usually discharge current
points were more frequent. The influence of low pressure was still
dominant to be easier to discharge. The non-linear property would be
appear explicitly on low pressure and heavily polluted condition.
Abstract: Safety of bus journey is a fundamental concern. Risk of injuries and fatalities is severe when bus superstructure fails during rollover accident. Adequate design and sufficient strength of bus superstructure can reduce the number of injuries and fatalities. This paper deals with structural analysis of bus superstructure undergoes rollover event. Several value of mass will be varied in multiple simulations. The purpose of this work is to analyze structural response of bus superstructure in terms of deformation, stress and strain under several loading and constraining conditions. A complete bus superstructure with forty four passenger-s capability was developed using finite element analysis software. Simulations have been conducted to observe the effect of total mass of bus on the strength of superstructure. These simulations are following United Nation Economic Commission of Europe regulation 66 which focuses on strength of large vehicle superstructure. Validation process had been done using simple box model experiment and results obtained are comparing with simulation results. Inputs data from validation process had been used in full scale simulation. Analyses suggested that, the failure of bus superstructure during rollover situation is basically dependent on the total mass of bus and on the strength of bus superstructure.
Abstract: The recent developments in computing and
communication technology permit to users to access multimedia
documents with variety of devices (PCs, PDAs, mobile phones...)
having heterogeneous capabilities. This diversification of supports
has trained the need to adapt multimedia documents according to
their execution contexts. A semantic framework for multimedia
document adaptation based on the conceptual neighborhood graphs
was proposed. In this framework, adapting consists on finding
another specification that satisfies the target constraints and which is
as close as possible from the initial document. In this paper, we
propose a new way of building the conceptual neighborhood graphs
to best preserve the proximity between the adapted and the original
documents and to deal with more elaborated relations models by
integrating the relations relaxation graphs that permit to handle the
delays and the distances defined within the relations.
Abstract: It is believed that DNA damaging toxic metabolites contributes to the development of different pathological conditions. To prevent harmful influence of toxic agents, cells developed number of protecting mechanisms, such as enzymatic reaction of detoxification of reactive metabolites and repair of DNA damage. The aim of the study was to examine the association between polymorphism of GSTT1/GSTM1 and XRCC1/3 genes and coronary artery disease (CAD) incidence. To examine a polymorphism of these genes in CAD susceptibility in patients and controls, PCR based genotyping assay was performed. For GST genes, frequency of GSTM1 null genotype among CAD affected group was significantly increased than in control group (P0.1). We found that neither XRCC1 Arg399Gln nor XRCC3 Thr241Met were associated with CAD risk. Obtained data suggests that GSTM1 null genotype carriers are more susceptible to CAD development.
Abstract: Wind power is among the most actively developing distributed generation (DG) technology. Majority of the wind power based DG technologies employ wind turbine induction generators (WTIG) instead of synchronous generators, for the technical advantages like: reduced size, increased robustness, lower cost, and increased electromechanical damping. However, dynamic changes of wind speed make the amount of active/reactive power injected/drawn to a WTIG embedded distribution network highly variable. This paper analyzes the effect of wind speed changes on the active and reactive power penetration to the wind energy embedded distribution network. Four types of wind speed changes namely; constant, linear change, gust change and random change of wind speed are considered in the analysis. The study is carried out by three-phase, non-linear, dynamic simulation of distribution system component models. Results obtained from the investigation are presented and discussed.
Abstract: This paper presents a real time force sensing
instrument that is designed for human gait analysis purposes. It is
capable of recording and monitoring ground reaction forces exerted
by human foot during various activities such as walking, running and
jumping in real time. In overall, force sensing mat mainly consists of
three elements: the force sensing mat, signal conditioning circuit and
data acquisition device. Force sensing mat is the mat that contains an
array of force sensing elements. To control and process the incoming
signal from the force sensing mat, Force-Logger and Force-Reloader
are developed using National Instrument Labview. This paper
describes the architecture of the force sensing mat, signal
conditioning circuit and the real time streaming of the incoming data
from the force sensing mat. Additionally, a preliminary experiment
dataset is presented in this paper.
Abstract: Stick models are widely used in studying the
behaviour of straight as well as skew bridges and viaducts subjected
to earthquakes while carrying out preliminary studies. The
application of such models to highly curved bridges continues to
pose challenging problems. A viaduct proposed in the foothills of the
Himalayas in Northern India is chosen for the study. It is having 8
simply supported spans @ 30 m c/c. It is doubly curved in horizontal
plane with 20 m radius. It is inclined in vertical plane as well. The
superstructure consists of a box section. Three models have been
used: a conventional stick model, an improved stick model and a 3D
finite element model. The improved stick model is employed by
making use of body constraints in order to study its capabilities. The
first 8 frequencies are about 9.71% away in the latter two models.
Later the difference increases to 80% in 50th mode. The viaduct was
subjected to all three components of the El Centro earthquake of May
1940. The numerical integration was carried out using the Hilber-
Hughes-Taylor method as implemented in SAP2000. Axial forces
and moments in the bridge piers as well as lateral displacements at
the bearing levels are compared for the three models. The maximum
difference in the axial forces and bending moments and
displacements vary by 25% between the improved and finite element
model. Whereas, the maximum difference in the axial forces,
moments, and displacements in various sections vary by 35%
between the improved stick model and equivalent straight stick
model. The difference for torsional moment was as high as 75%. It is
concluded that the stick model with body constraints to model the
bearings and expansion joints is not desirable in very sharp S curved
viaducts even for preliminary analysis. This model can be used only
to determine first 10 frequency and mode shapes but not for member
forces. A 3D finite element analysis must be carried out for
meaningful results.
Abstract: Possible advantages of technology in educational
context required the defining boundaries of formal and informal
learning. Increasing opportunity to ubiquitous learning by
technological support has revealed a question of how to discover
the potential of individuals in the spontaneous environments such as
social networks. This seems to be related with the question of what
purposes in social networks have been being used? Social networks
provide various advantages in educational context as collaboration,
knowledge sharing, common interests, active participation and
reflective thinking. As a consequence of these, the purpose of this
study is composed of proposing a new model that could determine
factors which effect adoption of social network applications for usage
in educational context. While developing a model proposal, the
existing adoption and diffusion models have been reviewed and they
are thought to be suitable on handling an original perspective instead
of using completely other diffusion or acceptance models because of
different natures of education from other organizations. In the
proposed model; social factors, perceived ease of use, perceived
usefulness and innovativeness are determined four direct constructs
that effect adoption process. Facilitating conditions, image,
subjective norms and community identity are incorporated to model
as antecedents of these direct four constructs.
Abstract: Data on 657 lactation from 163 Maltese goat,
collected over a 5-year period were analyzed by a mixed model to
estimate the variance components for heritability. The considered
lactation traits were: milk yield (MY) and lactation length (LL). Year,
parity and type of birth (single or twin) were significant sources of
variation for lactation length; on the other hand milk yield was
significantly influenced only by the year. The average MY was
352.34 kg and the average LL was 230 days. Estimates of heritability
were 0.21 and 0.15 for MY and LL respectively. These values
suggest there is low correlation between genotype and phenotype so
it may be difficult to evaluate animals directly on phenotype. So, the
genetic improvement of this breed may be quite slow without the
support of progeny test aimed to select Maltese breeders.
Abstract: Perishable goods constitute a large portion of retailer inventory and lose value with time due to deterioration and/or obsolescence. Retailers dealing with such goods required considering the factors of short shelf life and the dependency of sales on inventory displayed in determining optimal procurement policy. Many retailers follow the practice of using two bins - primary bin sales fresh items at a list price and secondary bin sales unsold items at a discount price transferred from primary bin on attaining certain age. In this paper, mathematical models are developed for primary bin and for secondary bin that maximizes profit with decision variables of order quantities, optimal review period and optimal selling price at secondary bin. The demand rates in two bins are assumed to be deterministic and dependent on displayed inventory level, price and age but independent of each other. The validity of the model is shown by solving an example and the sensitivity analysis of the model is also reported.
Abstract: The paper presents a complete discrete statistical framework, based on a novel vector quantization (VQ) front-end process. This new VQ approach performs an optimal distribution of VQ codebook components on HMM states. This technique that we named the distributed vector quantization (DVQ) of hidden Markov models, succeeds in unifying acoustic micro-structure and phonetic macro-structure, when the estimation of HMM parameters is performed. The DVQ technique is implemented through two variants. The first variant uses the K-means algorithm (K-means- DVQ) to optimize the VQ, while the second variant exploits the benefits of the classification behavior of neural networks (NN-DVQ) for the same purpose. The proposed variants are compared with the HMM-based baseline system by experiments of specific Arabic consonants recognition. The results show that the distributed vector quantization technique increase the performance of the discrete HMM system.