Abstract: Nowadays, power systems, energy generation by wind
has been very important. Noting that the production of electrical
energy by wind turbines on site to several factors (such as wind speed
and profile site for the turbines, especially off the wind input speed,
wind rated speed and wind output speed disconnect) is dependent. On
the other hand, several different types of turbines in the market there.
Therefore, selecting a turbine that its capacity could also answer the
need for electric consumers the efficiency is high something is
important and necessary. In this context, calculating the amount of
wind power to help optimize overall network, system operation, in
determining the parameters of wind power is very important.
In this article, to help calculate the amount of wind power plant,
connected to the national network in the region Manjil wind,
selecting the best type of turbine and power delivery profile
appropriate to the network using Monte Carlo method has been.
In this paper, wind speed data from the wind site in Manjil, as minute
and during the year has been. Necessary simulations based on
Random Numbers Simulation method and repeat, using the software
MATLAB and Excel has been done.
Abstract: Smoke from domestic wood burning has been
identified as a major contributor to air pollution, motivating detailed
emission measurements under controlled conditions. A series of
experiments was performed to characterise the emissions from wood
combustion in a fireplace and in a woodstove of two common species
of trees grown in Spain: Pyrenean oak (Quercus pyrenaica) and
black poplar (Populus nigra). Volatile organic compounds (VOCs) in
the exhaust emissions were collected in Tedlar bags, re-sampled in
sorbent tubes and analysed by thermal desorption-gas
chromatography-flame ionisation detection. Pyrenean oak presented
substantially higher emissions in the woodstove than in the fireplace,
for the majority of compounds. The opposite was observed for
poplar. Among the 45 identified species, benzene and benzenerelated
compounds represent the most abundant group, followed by
oxygenated VOCs and aliphatics. Emission factors obtained in this
study are generally of the same order than those reported for
residential experiments in the USA.
Abstract: In this study, multiwall carbon nanotubes (MWNTs)
were modified with nitric acid chemically and by dielectric barrier
discharge (DBD) plasma in an oxygen-based atmosphere. Used
carbon nanotubes (CNTs) were prepared by chemical vapour
deposition (CVD) floating catalyst method. For removing amorphous
carbon and metal catalyst, MWNTs were exposed to dry air and
washed with hydrochloric acid. Heating purified CNTs under helium
atmosphere caused elimination of acidic functional groups. Fourier
transformed infrared spectroscopy (FTIR) shows formation of
oxygen containing groups such as C=O and COOH. Brunauer,
Emmett, Teller (BET) analysis revealed that functionalization causes
generation of defects on the sidewalls and opening of the ends of
CNTs. Results of temperature-programmed desorption (TPD) and gas
chromatography(GC) indicate that nitric acid treatment create more
acidic groups than plasma treatment.
Abstract: Square pipes (pipes with square cross sections) are
being used for various industrial objectives, such as machine
structure components and housing/building elements. The utilization
of them is extending rapidly and widely. Hence, the out-put of those
pipes is increasing and new application fields are continually
developing.
Due to various demands in recent time, the products have to
satisfy difficult specifications with high accuracy in dimensions. The
reshaping process design of pipes with square cross sections;
however, is performed by trial and error and based on expert-s
experience.
In this paper, a computer-aided simulation is developed based on
the 2-D elastic-plastic method with consideration of the shear
deformation to analyze the reshaping process. Effect of various
parameters such as diameter of the circular pipe and mechanical
properties of metal on product dimension and quality can be
evaluated by using this simulation. Moreover, design of reshaping
process include determination of shrinkage of cross section,
necessary number of stands, radius of rolls and height of pipe at each
stand, are investigated. Further, it is shown that there are good
agreements between the results of the design method and the
experimental results.
Abstract: Infrastructure investments are important in developing
countries, it will not only help to foster the economic growth of a
nation, but it will also act as a platform in which new forms of
partnership and collaboration can be developed mainly in East Asian
countries. Since the last two decades, many infrastructure projects
had been completed through build-operate-transfer (BOT) type of
procurement. The developments of BOT have attracted participation
of local and foreign private sector investor to secure funding and to
deliver projects on time, within the budget and to the required
specifications. Private sectors are preferred by the government in
East Asia to participate in BOT projects due to lack of public
funding. The finding has resulted that the private sector or promoter
of the BOT projects is exposed to multiple risks which have been
discussed in this paper. Effective risk management methods and
good managerial skills are required in ensuring the success of the
project. The review indicated that mitigation measures should be
employed by the promoter throughout the concession period and
support from the host government is also required in ensuring the
success of the BOT project.
Abstract: The cDNA encoding the 326 amino acids of a Class I
basic chitinase gene from Leucaena leucocephala de Wit (KB3,
Genbank accession: AAM49597) was cloned under the control of
CaMV35S promoter in pCAMBIA 1300 and transferred to
Koshihikari. Calli of Koshihikari rice was transformed with
agrobacterium with this construct expressing the chitinase and β-
glucouronidase (GUS). The frequencies of calli 90 % has been
obtained from rice seedlings cultured on NB medium. The high
regeneration frequencies, 74% was obtained from calli cultured on
regeneration medium containing 4 mg/l BAP, and 7 g/l phytagel at
25°C. Various factors were studied in order to establish a procedure
for the transformation of Koshihikari Agrobacterium tumefaciens.
Supplementation of 50 mM acetosyringone to the medium during
coculivation was important to enhance the frequency to transient
transformation. The 4 week-old scutellum-derived calli were
excellent starting materials. Selection medium based on NB medium
supplement with 40 mg/l hygromycin and 400 mg/l cefotaxime were
an optimized medium for selection of transformed rice calli. The
percentage of transformation 70 was obtained. Recombinant calli and
regenerated rice plants were checked the expression of chitinase and
gus by PCR, northern blot gel, southern blot gel, and gus assay.
Chitinase and gus were expressed in all parts of recombinant rice.
The rice line expressing the KB3 chiitnase was more resistant to the
blast fungus Fusarium monoliforme than control line.
Abstract: The UK Government has emphasized the role of Local Authorities as a key player in its flagship residential energy efficiency strategies, by identifying and targeting areas for energy efficiency improvements. Residential energy consumption in England is characterized by significant geographical variation in energy demand, which makes centralized targeting of areas for energy efficiency intervention difficult. This paper draws on research which aims to understand how demographic, social, economic, urban form and climatic factors influence the geographical variations in English residential gas consumption. The paper reports the findings of a multiple regression model that shows how 64% of the geographical variation in residential gas consumption is accounted for by variations in these factors. Results from this study, after further refinement and validation, can be used by Local Authorities to identify areas within their boundaries that have higher than expected gas consumption, these may be prime targets for energy efficiency initiatives.
Abstract: The objective of this research is to develop the
performance indicators (PIs) in operational level for the Pre-hospital Emergency Medical Service (EMS) system employing in Thailand. This research started with ascertaining the current pre-hospital care
system. The team analyzed the strategies of Narerthorn, a government unit under the ministry of public health, and the existing PIs of the pre-hospital care. Afterwards, the current National Strategic Plan of EMS development (2008-2012) of the Emergency
Medical Institute of Thailand (EMIT) was considered using strategic
analysis to developed Strategy Map (SM) and identified the Success
Factors (SFs). The analysis results from strategy map and SFs were used to develop the Performance Indicators (PIs). To verify the set of
PIs, the team has interviewed with the relevant practitioners for the possibilities to implement the PIs. To this paper, it was to ascertain
that all the developed PIs support the objectives of the strategic plan. Nevertheless, the results showed that the operational level PIs suited
only with the first dimension of National Strategic Plan
(infrastructure and information technology development). Besides,
the SF was the infrastructure development (to contribute the EMS system to people throughout with standard and efficiency both in normally and disaster conditions). Finally, twenty-nine indicators
were developed from the analysis results of SM and SFs.
Abstract: Above Elbow Prosthesis is one of the most commonly
amputated or missing limbs. The research is done for modelling
techniques of upper limb prosthesis and design of high torque, light
weight and compact in size elbow actuator. The purposed actuator
consists of a DC motor, planetary gear set and a harmonic drive. The
calculations show that the actuator is good enough to be used in real
life powered prosthetic upper limb or rehabilitation exoskeleton.
Abstract: The objective of this paper is to study the electrical
resistivity complexity between field and laboratory measurement, in
order to improve the effectiveness of data interpretation for
geophysical ground resistivity survey. The geological outcrop in
Penang, Malaysia with an obvious layering contact was chosen as the
study site. Two dimensional geoelectrical resistivity imaging were
used in this study to maps the resistivity distribution of subsurface,
whereas few subsurface sample were obtained for laboratory
advance. In this study, resistivity of samples in original conditions is
measured in laboratory by using time domain low-voltage technique,
particularly for granite core sample and soil resistivity measuring set
for soil sample. The experimentation results from both schemes are
studied, analyzed, calibrated and verified, including basis and
correlation, degree of tolerance and characteristics of substance.
Consequently, the significant different between both schemes is
explained comprehensively within this paper.
Abstract: In this paper, transversal vibration of buried pipelines
during loading induced by underground explosions is analyzed. The
pipeline is modeled as an infinite beam on an elastic foundation, so
that soil-structure interaction is considered by means of transverse
linear springs along the pipeline. The pipeline behavior is assumed to
be ideal elasto-plastic which an ultimate strain value limits the plastic
behavior. The blast loading is considered as a point load, considering
the affected length at some point of the pipeline, in which the
magnitude decreases exponentially with time. A closed-form solution
for the quasi-static problem is carried out for both elastic and elasticperfect
plastic behaviors of pipe materials. At the end, a comparative
study on steel and polyethylene pipes with different sizes buried in
various soil conditions, affected by a predefined underground
explosion is conducted, in which effect of each parameter is
discussed.
Abstract: Blood pulse is an important human physiological signal commonly used for the understanding of the individual physical health. Current methods of non-invasive blood pulse sensing require direct contact or access to the human skin. As such, the performances of these devices tend to vary with time and are subjective to human body fluids (e.g. blood, perspiration and skin-oil) and environmental contaminants (e.g. mud, water, etc). This paper proposes a simulation model for the novel method of non-invasive acquisition of blood pulse using the disturbance created by blood flowing through a localized magnetic field. The simulation model geometry represents a blood vessel, a permanent magnet, a magnetic sensor, surrounding tissues and air in 2-dimensional. In this model, the velocity and pressure fields in the blood stream are described based on Navier-Stroke equations and the walls of the blood vessel are assumed to have no-slip condition. The blood assumes a parabolic profile considering a laminar flow for blood in major artery near the skin. And the inlet velocity follows a sinusoidal equation. This will allow the computational software to compute the interactions between the magnetic vector potential generated by the permanent magnet and the magnetic nanoparticles in the blood. These interactions are simulated based on Maxwell equations at the location where the magnetic sensor is placed. The simulated magnetic field at the sensor location is found to assume similar sinusoidal waveform characteristics as the inlet velocity of the blood. The amplitude of the simulated waveforms at the sensor location are compared with physical measurements on human subjects and found to be highly correlated.
Abstract: The objective of this paper is to estimate realistic
principal extrusion process parameters by means of artificial neural
network. Conventionally, finite element analysis is used to derive
process parameters. However, the finite element analysis of the
extrusion model does not consider the manufacturing process
constraints in its modeling. Therefore, the process parameters
obtained through such an analysis remains highly theoretical.
Alternatively, process development in industrial extrusion is to a
great extent based on trial and error and often involves full-size
experiments, which are both expensive and time-consuming. The
artificial neural network-based estimation of the extrusion process
parameters prior to plant execution helps to make the actual extrusion
operation more efficient because more realistic parameters may be
obtained. And so, it bridges the gap between simulation and real
manufacturing execution system. In this work, a suitable neural
network is designed which is trained using an appropriate learning
algorithm. The network so trained is used to predict the
manufacturing process parameters.
Abstract: An optical fiber Fabry-Perot interferometer (FFPI) is
proposed and demonstrated for dynamic measurements in a
mechanical vibrating target. A polishing metal with a low reflectance
value adhered to a mechanical vibrator was excited via a function
generator at various excitation frequencies. Output interference
fringes were generated by modulating the reference and sensing
signal at the output arm. A fringe-counting technique was used for
interpreting the displacement information on the dedicated computer.
The fiber interferometer has been found the capability of the
displacement measurements of 1.28 μm – 96.01 μm. A commercial
displacement sensor was employed as a reference sensor for
investigating the measurement errors from the fiber sensor. A
maximum percentage measurement error of approximately 1.59 %
was obtained.
Abstract: MinC plays an important role in bacterial cell division
system by inhibiting FtsZ assembly. However, the molecular
mechanism of the action is poorly understood. E. coli MinC Nterminus
domain was purified and crystallized using 1.4 M sodium
citrate pH 6.5 as a precipitant. X-ray diffraction data was collected
and processed to 2.3 Å from a native crystal. The crystal belonged to
space group P212121, with the unit cell parameters a = 52.7, b = 54.0,
c = 64.7 Å. Assuming the presence of two molecules in the
asymmetric unit, the Matthews coefficient value is 1.94 Å3 Da-1,
which corresponds to a solvent content of 36.5%. The overall
structure of MinCN is observed as a dimer form through anti-parallel
ß-strand interaction.
Abstract: Conventionally the selection of parameters depends
intensely on the operator-s experience or conservative technological
data provided by the EDM equipment manufacturers that assign
inconsistent machining performance. The parameter settings given by
the manufacturers are only relevant with common steel grades. A
single parameter change influences the process in a complex way.
Hence, the present research proposes artificial neural network (ANN)
models for the prediction of surface roughness on first commenced
Ti-15-3 alloy in electrical discharge machining (EDM) process. The
proposed models use peak current, pulse on time, pulse off time and
servo voltage as input parameters. Multilayer perceptron (MLP) with
three hidden layer feedforward networks are applied. An assessment
is carried out with the models of distinct hidden layer. Training of the
models is performed with data from an extensive series of
experiments utilizing copper electrode as positive polarity. The
predictions based on the above developed models have been verified
with another set of experiments and are found to be in good
agreement with the experimental results. Beside this they can be
exercised as precious tools for the process planning for EDM.
Abstract: Analytical solution of the first-order and third-order
shear deformation theories are developed to study the free vibration
behavior of simply supported functionally graded plates. The
material properties of plate are assumed to be graded in the thickness
direction as a power law distribution of volume fraction of the
constituents. The governing equations of functionally graded plates
are established by applying the Hamilton's principle and are solved
by using the Navier solution method. The influence of side-tothickness
ratio and constituent of volume fraction on the natural
frequencies are studied. The results are validated with the known
data in the literature.
Abstract: The paper proposes an approach using genetic algorithm for computing the region based image similarity. The image is denoted using a set of segmented regions reflecting color and texture properties of an image. An image is associated with a family of image features corresponding to the regions. The resemblance of two images is then defined as the overall similarity between two families of image features, and quantified by a similarity measure, which integrates properties of all the regions in the images. A genetic algorithm is applied to decide the most plausible matching. The performance of the proposed method is illustrated using examples from an image database of general-purpose images, and is shown to produce good results.
Abstract: The bypass exhaust system of a 160 MW combined cycle has been modeled and analyzed using numerical simulation in 2D prospective. Analysis was carried out using the commercial numerical simulation software, FLUENT 6.2. All inputs were based on the technical data gathered from working conditions of a Siemens V94.2 gas turbine, installed in the Yazd power plant. This paper deals with reduction of pressure drop in bypass exhaust system using turning vanes mounted in diverter box in order to alleviate turbulent energy dissipation rate above diverter box. The geometry of such turning vanes has been optimized based on the flow pattern at diverter box inlet. The results show that the use of optimized turning vanes in diverter box can improve the flow pattern and eliminate vortices around sharp edges just before the silencer. Furthermore, this optimization could decrease the pressure drop in bypass exhaust system and leads to higher plant efficiency.
Abstract: Different numerical methods are employed and developed for simulating interfacial flows. A large range of applications belong to this group, e.g. two-phase flows of air bubbles in water or water drops in air. In such problems surface tension effects often play a dominant role. In this paper, various models of surface tension force for interfacial flows, the CSF, CSS, PCIL and SGIP models have been applied to simulate the motion of small air bubbles in water and the results were compared and reviewed. It has been pointed out that by using SGIP or PCIL models, we are able to simulate bubble rise and obtain results in close agreement with the experimental data.