Abstract: This paper reports on the theoretical performance
analysis of the 1.3 μm In0.42Ga0.58As /In0.26Ga0.74As multiple quantum
well (MQW) vertical cavity surface emitting laser (VCSEL) on the
ternary In0.31Ga0.69As substrate. The output power of 2.2 mW has
been obtained at room temperature for 7.5 mA injection current. The
material gain has been estimated to be ~3156 cm-1 at room
temperature with the injection carrier concentration of 2×1017 cm-3.
The modulation bandwidth of this laser is measured to be 9.34 GHz
at room temperature for the biasing current of 2 mA above the
threshold value. The outcomes reveal that the proposed InGaAsbased
MQW laser is the promising one for optical communication
system.
Abstract: Oral health is particular important to the hospitalized
patients with chronic schizophrenia for an extreme high potential of the respiratory infections. Due to the degeneration of physical capability, patients of this kind typically fall dependent in the activity of daily living (ADL). A very high percentage of patients had dental
problems of which mostly could be easily avoid by easy regular tooth brushing. Purpose of the project is to develop a mechanism in helping the schizophrenia patients in rebuilding a tooth-cleaning habit. The
project observed and evaluated the tooth-cleaning behavior of 100
male patients in a psychiatric hospital, and found the majority of them
ignored such an activity in a three-month period of time. In the meantime, the primary care-givers were not aware or not convinced
the importance of such a need of dental hygiene, and thus few if any
tooth cleaning training or knowledge on dental hygiene were given to
the patients. The project then developed a program based on the numerous observations and discussions. The improvement program
included patients- group education, care-givers- training, and a
tool-kit for tooth-brush holding was erected. The project launched
with some incentive package. The outcomes were encouraging with
87% of the patients had rebuilt their tooth-brushing habits against
previous 22%, and the tooth cleaning kits were 100% kept against 22%
in the past. This project had significantly improved the oral health of
the patients. The project, included the procedure and the tool-kit
holder specific for this purpose, was a good examples for psychiatric
hospitals.
Abstract: Zeolite A and MCM-41 have extensive applications in basic science, petrochemical science, energy conservation/storage, medicine, chemical sensor, air purification, environmentally benign composite structure and waste remediation. However, the use of zeolite A and MCM-41 in these areas, especially environmental remediation, are restricted due to prohibitive production cost. Efficient recycling of and resource recovery from coal fly ash has been a major topic of current international research interest, aimed at achieving sustainable development of human society from the viewpoints of energy, economy, and environmental strategy. This project reported an original, novel, green and fast methods to produce nano-porous zeolite A and MCM-41 materials from coal fly ash. For zeolite A, this novel production method allows a reduction by half of the total production time while maintaining a high degree of crystallinity of zeolite A which exists in a narrower particle size distribution. For MCM-41, this remarkably green approach, being an environmentally friendly process and reducing generation of toxic waste, can produce pure and long-range ordered MCM-41 materials from coal fly ash. This approach took 24 h at 25 oC to produce 9 g of MCM-41 materials from 30 g of the coal fly ash, which is the shortest time and lowest reaction temperature required to produce pure and ordered MCM-41 materials (having the largest internal surface area) compared to the values reported in the literature. Performance evaluation of the produced zeolite A and MCM-41 materials in wastewater treatment and air pollution control were reported. The residual fly ash was also converted to zeolite Na-P1 which showed good performance in removal of multi-metal ions in wastewater. In wastewater treatment, compared to commercial-grade zeolite A, adsorbents produced from coal fly ash were effective in removing multi heavy metal ions in water and could be an alternative material for treatment of wastewater. In methane emission abatement, the zeolite A (produced from coal fly ash) achieved similar methane removal efficiency compared to the zeolite A prepared from pure chemicals. This report provides the guidance for production of zeolite A and MCM-41 from coal fly ash by a cost-effective approach which opens potential applications of these materials in environmental industry. Finally, environmental and economic aspects of production of zeolite A and MCM-41 from coal fly ash were discussed.
Abstract: Unlike Christianity and Buddhism, Islam, being one
of the three universal world religions, actively penetrates into
people-s everyday life. The main reason for this is that in Islam the
religion and ideology, philosophy, religious organizations and state
bodies are closely interrelated. In order to analyze the state of being
of interrelations of religion and civil society in Kazakhstan, it is
necessary to study Islam and its relations with spiritual culture of the
society. According to the Constitution of the Republic of Kazakhstan
the religion is separated from the state, i.e. each performs its own
function without interfering into each other-s affairs. The right of the
citizens of our republic to freedom of thinking and faith is based on
the Constitution of the RK, Civil Code, Law “On freedom of faith
and religious unions in the Republic of Kazakhstan".
Legislatively secured separation of the mosque and church from
the state does not mean that religion has no influence on the latter.
The state, consisting of citizens with their own beliefs, including
religious ones, cannot be isolated from the influence of religion.
Nowadays it is commonly accepted that it is not possible to
understand and forecast key social processes without taking into
account the religious factor.
Abstract: Formative usability evaluation aims at finding
usability problems during the development process. The earlier these
problems are identified, the less expensive to fix they are. This paper
presents some preliminary results from a formative usability testing
of the 1st prototype developed for the ARiSE (Augmented Reality in
School Environments) project.
Abstract: In this paper, a heuristic method for simultaneous
rescue robot path-planning and mission scheduling is introduced
based on project management techniques, multi criteria decision
making and artificial potential fields path-planning. Groups of
injured people are trapped in a disastrous situation. These people are
categorized into several groups based on the severity of their
situation. A rescue robot, whose ultimate objective is reaching
injured groups and providing preliminary aid for them through a path
with minimum risk, has to perform certain tasks on its way towards
targets before the arrival of rescue team. A decision value is assigned
to each target based on the whole degree of satisfaction of the criteria
and duties of the robot toward the target and the importance of
rescuing each target based on their category and the number of
injured people. The resulted decision value defines the strength of the
attractive potential field of each target. Dangerous environmental
parameters are defined as obstacles whose risk determines the
strength of the repulsive potential field of each obstacle. Moreover,
negative and positive energies are assigned to the targets and
obstacles, which are variable with respects to the factors involved.
The simulation results show that the generated path for two cases
studies with certain differences in environmental conditions and
other risk factors differ considerably.
Abstract: The main objectives of this study are to inspect and
identify any damage of jaimusi highway prestressed concrete bridge
after repair and strengthening of damaged structural members and to
evaluate the performance of the bridge structural members by
adopting static load test. Inspection program after repair and
strengthening includes identifying and evaluating the structural
members of bridge such as T-shape cantilever structure, hanging
beams, corbels, external tendons, anchor beams, sticking steel plate,
and piers. The results of inspection show that the overall state of the
bridge structural member after repair and strengthening is good. The
results of rebound test of concrete strength show that the average
strength of concrete is 46.31Mpa. Whereas, the average value of
concrete strength of anchor beam is 49.82Mpa. According to the
results of static load test, the experimental values are less than
theoretical values of internal forces, deflection, and strain, indicating
that the stiffness of the experimental structure, overall deformation
and integrity satisfy the designed standard and the working
performance is good, and the undertaking capacity has a certain
surplus. There is not visible change in the length and width of cracks
and there are not new cracks under experimental load.
Abstract: In this paper the fatigue crack initiation location of double shear lap joints, treated by interference fit and bolt clamping, have been investigated both experimentally and numerically. To do so, using the fracture section of available fatigue tested specimens of interference fitted and torque tightened Aluminum 2024-T3 plates, the crack initiation location was determined. The stress distribution attained from the finite element analysis was used to help explain the results observed in the experimental tests. The results showed that the fatigue crack initiation location changes from top and mid plane at the hole edge to somewhere far from the hole edge (stress concentration region) in different combination of clamping force, interference fit size and applied cyclic load ranges. It is worth mentioning that the fatigue crack initiation location affects the fatigue life of the specimens too.
Abstract: This paper presents the experiment results of investigating the effects of adding various types and proportions of fibre on mechanical strength and permeability characteristics of recycled aggregate concrete (RAC), which was produced with treated coarse recycled concrete aggregate (RCA). Two types of synthetic fibres (i.e., barchip and polypropylene fibre) with various volume fractions were added to the RAC, which was calculated by the weight of the cement. The hardened RAC properties such as compressive strength, flexural strength, ultrasonic pulse velocity, water absorption and total porosity at the curing ages of 7 and 28 days were evaluated and compared with the properties of the control specimens. Results indicate that the treated coarse RCA enhances the mechanical strength and permeability properties of RAC and adding barchip fibre further optimises the results. Adding 1.2% barchip fibre has the best effect on the mechanical strength performance of the RAC.
Abstract: Using finite element method (FEM), the elastic
new strain-concentration factor (SNCF) of cylindrical bars
with circumferential flat-bottom groove is studied. This new
SNCF has been defined under triaxial stress state. The
employed specimens have constant groove depth with net
section and gross diameters of 10.0 and 16.7 mm,
respectively. The length of flatness ao has been varied form
0.0 ~12.5 mm to study the elastic SNCF of this type of
geometrical irregularities. The results that the elastic new
SNCF rapidly drops from its elastic value of the groove with
ao = 0.0, i.e. circumferential U-notch, and reaches minimum
value at ao = 2 mm. After that the elastic new SNCF becomes
nearly constant with increasing flatness length (ao). The value
of tensile load at yielding at the groove root increases with
increasing ao. The current results show that severity of the
notch decreases with increasing flatness length ao.
Abstract: Yam starch obtained from the water yam (munlued)
by the wet milling process was studied for some physicochemical
properties. Yam starch film was prepared by casting using glycerol as
a plasticizer. The effect of different glycerol (1.30, 1.65 and
2.00g/100g of filmogenic solution) and starch concentrations (3.30,
3.65 and 4.00g /100g of filmogenic solution) were evaluated on some
characteristics of the film. The temperature for obtaining the
gelatinized starch solution was 70-80°C and then dried at 45°C for 4
hours. The resulting starch from munlued granular morphology was
triangular and the average size of the granule was 26.68 μm. The
amylose content by colorimetric method was 26 % and the gelatinize
temperature was 70-80°C. The appearance of the film was smooth,
transparent, and glossy with average moisture content of 25.96% and
thickness of 0.01mm. Puncture deformation and flexibility increased
with glycerol content. The starch and glycerol concentration were a
significant factor of the yam starch film characteristics. Yam starch
film can be described as a biofilm providing many applications and
developments with the advantage of biodegradability.
Abstract: Managing the emergency situations at the Emergency
Staff requires a high co-operation between its members and their fast
decision making. For these purpose it is necessary to prepare Emergency Staff members adequately. The aim of this paper is to
describe the development of information support that focuses to
emergency staff processes and effective decisions. The information
support is based on the principles of process management, and
Process Framework for Emergency Management was used during the
development. The output is the information system that allows users
to simulate an emergency situation, including effective decision making. The system also evaluates the progress of the emergency
processes solving by quantitative and qualitative indicators. By using
the simulator, a higher quality education of specialists can be achieved. Therefore, negative impacts resulting from arising emergency situations can be directly reduced.
Abstract: Money laundering has been described by many as the lifeblood of crime and is a major threat to the economic and social well-being of societies. It has been recognized that the banking system has long been the central element of money laundering. This is in part due to the complexity and confidentiality of the banking system itself. It is generally accepted that effective anti-money laundering (AML) measures adopted by banks will make it tougher for criminals to get their "dirty money" into the financial system. In fact, for law enforcement agencies, banks are considered to be an important source of valuable information for the detection of money laundering. However, from the banks- perspective, the main reason for their existence is to make as much profits as possible. Hence their cultural and commercial interests are totally distinct from that of the law enforcement authorities. Undoubtedly, AML laws create a major dilemma for banks as they produce a significant shift in the way banks interact with their customers. Furthermore, the implementation of the laws not only creates significant compliance problems for banks, but also has the potential to adversely affect the operations of banks. As such, it is legitimate to ask whether these laws are effective in preventing money launderers from using banks, or whether they simply put an unreasonable burden on banks and their customers. This paper attempts to address these issues and analyze them against the background of the Malaysian AML laws. It must be said that effective coordination between AML regulator and the banking industry is vital to minimize problems faced by the banks and thereby to ensure effective implementation of the laws in combating money laundering.
Abstract: A series of microarray experiments produces observations
of differential expression for thousands of genes across multiple
conditions.
Principal component analysis(PCA) has been widely used in
multivariate data analysis to reduce the dimensionality of the data in
order to simplify subsequent analysis and allow for summarization of
the data in a parsimonious manner. PCA, which can be implemented
via a singular value decomposition(SVD), is useful for analysis of
microarray data.
For application of PCA using SVD we use the DNA microarray
data for the small round blue cell tumors(SRBCT) of childhood
by Khan et al.(2001). To decide the number of components which
account for sufficient amount of information we draw scree plot.
Biplot, a graphic display associated with PCA, reveals important
features that exhibit relationship between variables and also the
relationship of variables with observations.
Abstract: We present a novel scheme to evaluate sinusoidal functions with low complexity and high precision using cubic spline interpolation. To this end, two different approaches are proposed to find the interpolating polynomial of sin(x) within the range [- π , π]. The first one deals with only a single data point while the other with two to keep the realization cost as low as possible. An approximation error optimization technique for cubic spline interpolation is introduced next and is shown to increase the interpolator accuracy without increasing complexity of the associated hardware. The architectures for the proposed approaches are also developed, which exhibit flexibility of implementation with low power requirement.
Abstract: In this empirical research, how marketing managers evaluate their firms- performances and decide to make innovation is examined. They use some standards which are past performance of the firm, target performance of the firm, competitor performance, and average performance of the industry to compare and evaluate the firms- performances. It is hypothesized that marketing managers and owners of the firm compare the firms- current performance with these four standards at the same time to decide when to make innovation relating to any aspects of the firm, either management style or products. Relationship between the comparison of the firm-s performance with these standards and innovation are searched in the same regression model. The results of the regression analysis are discussed and some recommendations are made for future studies and applicants.
Abstract: Embedded systems need to respect stringent real
time constraints. Various hardware components included in such
systems such as cache memories exhibit variability and therefore
affect execution time. Indeed, a cache memory access from an
embedded microprocessor might result in a cache hit where the
data is available or a cache miss and the data need to be fetched
with an additional delay from an external memory. It is therefore
highly desirable to predict future memory accesses during
execution in order to appropriately prefetch data without incurring
delays. In this paper, we evaluate the potential of several artificial
neural networks for the prediction of instruction memory
addresses. Neural network have the potential to tackle the nonlinear
behavior observed in memory accesses during program
execution and their demonstrated numerous hardware
implementation emphasize this choice over traditional forecasting
techniques for their inclusion in embedded systems. However,
embedded applications execute millions of instructions and
therefore millions of addresses to be predicted. This very
challenging problem of neural network based prediction of large
time series is approached in this paper by evaluating various neural
network architectures based on the recurrent neural network
paradigm with pre-processing based on the Self Organizing Map
(SOM) classification technique.
Abstract: The objectives of this research are to produce
prototype coconut oil based solvent offset printing inks and to
analyze a basic quality of printing work derived from coconut oil
based solvent offset printing inks, by mean of bringing coconut oil
for producing varnish and bringing such varnish to produce black
offset printing inks. Then, analysis of qualities i.e. CIELAB value,
density value, and dot gain value of printing work from coconut oil
based solvent offset printing inks which printed on gloss-coated
woodfree paper weighs 130 grams were done. The research result of
coconut oil based solvent offset printing inks indicated that the
suitable varnish formulation is using 51% of coconut oil, 36% of
phenolic resin, and 14% of solvent oil 14%, while the result of
producing black offset ink displayed that the suitable formula of
printing ink is using varnish mixed with 20% of coconut oil, and the
analyzing printing work of coconut oil based solvent offset printing
inks which printed on paper, the results were as follows: CIELAB
value of black offset printing ink is at L* = 31.90, a* = 0.27, and b* =
1.86, density value is at 1.27 and dot gain value was high at mid tone
area of image area.
Abstract: Echocardiography imaging is one of the most common diagnostic tests that are widely used for assessing the abnormalities of the regional heart ventricle function. The main goal of the image enhancement task in 2D-echocardiography (2DE) is to solve two major anatomical structure problems; speckle noise and low quality. Therefore, speckle noise reduction is one of the important steps that used as a pre-processing to reduce the distortion effects in 2DE image segmentation. In this paper, we present the common filters that based on some form of low-pass spatial smoothing filters such as Mean, Gaussian, and Median. The Laplacian filter was used as a high-pass sharpening filter. A comparative analysis was presented to test the effectiveness of these filters after being applied to original 2DE images of 4-chamber and 2-chamber views. Three statistical quantity measures: root mean square error (RMSE), peak signal-to-ratio (PSNR) and signal-tonoise ratio (SNR) are used to evaluate the filter performance quantitatively on the output enhanced image.
Abstract: Flexible Job Shop Problem (FJSP) is an extension of
classical Job Shop Problem (JSP). The FJSP extends the routing
flexibility of the JSP, i.e assigning machine to an operation. Thus it
makes it more difficult than the JSP. In this study, Cooperative Coevolutionary
Genetic Algorithm (CCGA) is presented to solve the
FJSP. Makespan (time needed to complete all jobs) is used as the
performance evaluation for CCGA. In order to test performance and
efficiency of our CCGA the benchmark problems are solved.
Computational result shows that the proposed CCGA is comparable
with other approaches.