Abstract: In this paper, effects of using Alumina-water
nanofluid on the rate of heat transfer have been investigated
numerically. Physical model is a square enclosure with insulated top
and bottom horizontal walls, while the vertical walls are kept at
different constant temperatures. Two appropriate models are used to
evaluate the viscosity and thermal conductivity of nanofluid. The
governing stream-vorticity equations are solved using a second order
central finite difference scheme, coupled to the conservation of mass
and energy. The study has been carried out for the Richardson
number 0.1 to 10 and the solid volume fraction 0 to 0.04. Results are
presented by isotherms lines, average Nusselt number and normalized
Nusselt number in different range of φ and Ri for forced, combined
and natural convection dominated regime. It is found that higher heat
transfer rate is predicted when the effects of nanoparticle is taken into
account.
Abstract: Numerical studies were conducted using Lattice
Boltzmann Method (LBM) to study the natural convection in a square
cavity in the presence of roughness. An algorithm based on a single
relaxation time Bhatnagar-Gross-Krook (BGK) model of Lattice
Boltzmann Method (LBM) was developed. Roughness was
introduced on both the hot and cold walls in the form of sinusoidal
roughness elements. The study was conducted for a Newtonian fluid
of Prandtl number (Pr) 1.0. The range of Ra number was explored
from 10^3 to 10^6 in a laminar region. Thermal and hydrodynamic
behavior of fluid was analyzed using a differentially heated square
cavity with roughness elements present on both the hot and cold wall.
Neumann boundary conditions were introduced on horizontal walls
with vertical walls as isothermal. The roughness elements were at the
same boundary condition as corresponding walls. Computational
algorithm was validated against previous benchmark studies
performed with different numerical methods, and a good agreement
was found to exist. Results indicate that the maximum reduction in
the average heat transfer was 16.66 percent at Ra number 10^5.
Abstract: This paper addresses the issue of the autonomous
mobile robot (AMR) navigation task based on the hybrid control
modes. The novel hybrid control mode, based on multi-sensors
information by using the fuzzy approach, has been presented in this
research. The system operates in real time, is robust, enables the robot
to operate with imprecise knowledge, and takes into account the
physical limitations of the environment in which the robot moves,
obtaining satisfactory responses for a large number of different
situations. An experiment is simulated and carried out with a pioneer
mobile robot. From the experimental results, the effectiveness and
usefulness of the proposed AMR obstacle avoidance and navigation
scheme are confirmed. The experimental results show the feasibility,
and the control system has improved the navigation accuracy. The
implementation of the controller is robust, has a low execution time,
and allows an easy design and tuning of the fuzzy knowledge base.
Abstract: Activated carbons (M4P0, M4P2, and M5P2) used in
this research were produced from palm shell and polyetherether
ketone (PEEK) via carbonization, impregnation and microwave
activation. The adsorption/desorption process was carried out using
static volumetric adsorption. Regeneration is important in the overall
economy of the process and waste minimization. This work focuses
on the thermal regeneration of the CO2 exhausted microwave
activated carbons. The regeneration strategy adopted was thermal
with nitrogen purge desorption with N2 feed flow rate of 20 ml/min
for 1 h at atmospheric pressure followed by drying at 150oC.Seven
successive adsorption/regeneration processes were carried out on the
material. It was found that after seven adsorption regeneration cycles;
the regeneration efficiency (RE) for CO2 activated carbon from palm
shell only (M4P0) was more than 90% while that of hybrid palm
shell-PEEK (M4P2, M5P2) was above 95%. The cyclic adsorption
and regeneration shows the stability of the adsorbent materials.
Abstract: The purpose of this study is to investigate the kinematic
characteristics and differences of the snatch barbell trajectory of 53 kg
class female weight lifters. We take the 2014 Taiwan College Cup
players as examples, and tend to make kinematic applications through
the proven weightlifting barbell track system. The competition videos
are taken by consumer camcorder with a tripod which set up at the side
of the lifter. The results will be discussed in three parts, the first part is
various lifting phase, the second part is the compare lifting between
success and unsuccessful, and the third part is to compare the
outstanding player with the general. Conclusion through the barbell
can be used to observe the trajectories of our players lifting the usual
process cannot be observed in the presence of malfunction or habits, so
that the coach can find the problem and guide the players more
accurately. Our system can be applied in practice and competition to
increase the resilience of the lifter on the field.
Abstract: Poly vinyl acetate (PVA)-based titania (TiO2)–carbon
nanotube composite nanofibers (PVA-TCCNs) with various
PVA-to-solvent ratios and PVA-based TiO2 composite nanofibers
(PVA-TN) were synthesized using an electrospinning process,
followed by thermal treatment. The photocatalytic activities of these
nanofibers in the degradation of airborne monocyclic aromatics under
visible-light irradiation were examined. This study focuses on the
application of these photocatalysts to the degradation of the target
compounds at sub-part-per-million indoor air concentrations. The
characteristics of the photocatalysts were examined using scanning
electron microscopy, X-ray diffraction, ultraviolet-visible
spectroscopy, and Fourier-transform infrared spectroscopy. For all the
target compounds, the PVA-TCCNs showed photocatalytic
degradation efficiencies superior to those of the reference PVA-TN.
Specifically, the average photocatalytic degradation efficiencies for
benzene, toluene, ethyl benzene, and o-xylene (BTEX) obtained using
the PVA-TCCNs with a PVA-to-solvent ratio of 0.3 (PVA-TCCN-0.3)
were 11%, 59%, 89%, and 92%, respectively, whereas those observed
using PVA-TNs were 5%, 9%, 28%, and 32%, respectively.
PVA-TCCN-0.3 displayed the highest photocatalytic degradation
efficiency for BTEX, suggesting the presence of an optimal
PVA-to-solvent ratio for the synthesis of PVA-TCCNs. The average
photocatalytic efficiencies for BTEX decreased from 11% to 4%, 59%
to 18%, 89% to 37%, and 92% to 53%, respectively, when the flow
rate was increased from 1.0 to 4.0 L min1. In addition, the average
photocatalytic efficiencies for BTEX increased 11% to ~0%, 59% to
3%, 89% to 7%, and 92% to 13%, respectively, when the input
concentration increased from 0.1 to 1.0 ppm. The prepared
PVA-TCCNs were effective for the purification of airborne aromatics
at indoor concentration levels, particularly when the operating
conditions were optimized.
Abstract: In this paper, reliable consensus of multi-agent systems
with sampled-data is investigated. By using a suitable
Lyapunov-Krasovskii functional and some techniques such as
Wirtinger Inequality, Schur Complement and Kronecker Product, the
results of such system are obtained by solving a set of Linear Matrix
Inequalities (LMIs). One numerical example is included to show the
effectiveness of the proposed criteria.
Abstract: The mixed micellization of adiphenine hydrochloride (ADP) with 1-decyl-3-methylimidazolium chloride (C10mim.Cl), was investigated at different mole fractions and temperatures by surface tension measurements. The synergistic behavior (i.e., non-ideal behavior) for binary mixtures was explained by the deviation of critical micelle concentration (cmc) from ideal critical micelle concentration (cmc*), micellar mole fraction (Xim) from ideal micellar mole fraction (Xiideal), the values of interaction parameter (β) and activity coefficients (fi) (for both mixed micelles and mixed monolayer). The excess free energy (ΔGex) for the ADP- C10mim.Cl binary mixtures explain the stability of mixed micelles in comparison to micelles of pure ADP and C10mim.Cl. Interfacial parameters, i.e., Gibbs surface excess (Гmax), minimum head group area at air/ water
interface (Amin), and free energy of micellization (ΔG0m) were also evaluated for the systems.
Abstract: Carbon Deposits are often occurred inside the
industrial coke oven during coking process. Accumulation of carbon
deposits may cause a big issue, which seriously influences the coking
operation. The carbon is burning off by injecting fresh air through
pipes into coke oven which is an efficient way practically operated in
industries. The burning off carbon deposition in coke oven performed
by Computational Fluid Dynamics (CFD) method has provided an
evaluation of the feasibility study. A three dimensional, transient,
turbulent reacting flow simulation has performed with three different
injecting air flow rate and another kind of injecting configuration. The
result shows that injection higher air flow rate would effectively
reduce the carbon deposits. In the meantime, the opened charging
holes would suck extra oxygen from atmosphere to participate in
reactions. In term of coke oven operating limits, the wall temperatures
are monitored to prevent over-heating of the adiabatic walls during
burn-off process.
Abstract: This paper presents two techniques, local feature
extraction using image spectrum and low frequency spectrum
modelling using GMM to capture the underlying statistical
information to improve the performance of face recognition
system. Local spectrum features are extracted using overlap sub
block window that are mapped on the face image. For each of this
block, spatial domain is transformed to frequency domain using
DFT. A low frequency coefficient is preserved by discarding high
frequency coefficients by applying rectangular mask on the
spectrum of the facial image. Low frequency information is non-
Gaussian in the feature space and by using combination of several
Gaussian functions that has different statistical properties, the best
feature representation can be modelled using probability density
function. The recognition process is performed using maximum
likelihood value computed using pre-calculated GMM components.
The method is tested using FERET datasets and is able to achieved
92% recognition rates.
Abstract: Presently, it is necessary to ensure the sustainable
development of passenger and freight transport. Increasing
performance of road freight has had a negative impact to environment
and society. It is therefore necessary to increase the competitiveness
of intermodal transport, which is more environmentally friendly. The
study describes the effectiveness of logistical centers realization for
companies and society and research how the partial internalization of
external costs reflected in the efficient use of these centers and
increase the competitiveness of intermodal transport to road freight.
In our research, we use the method of comparative analysis and
market research to describe the advantages of logistic centers for their
users as well as for society as a whole. Method normal costing is used
for calculation infrastructure and total costs, method of conversion
costing for determine the external costs. We modelled total society
costs for road freight transport and inter modal transport chain (we
assumed that most of the traffic is carried by rail) with different
loading schemes for condition in the Slovak Republic. Our research
has shown that higher utilization of inter modal transport chain do
good not only for society, but for companies providing freight
services too. Increase in use of inter modal transport chain can bring
many benefits to society that do not bring direct immediate financial
return. They often bring the multiplier effects, such as greater use of
environmentally friendly transport mode and reduce the total society
costs.
Abstract: This paper describes the problem of building secure
computational services for encrypted information in the Cloud
Computing without decrypting the encrypted data; therefore, it meets
the yearning of computational encryption algorithmic aspiration
model that could enhance the security of big data for privacy,
confidentiality, availability of the users. The cryptographic model
applied for the computational process of the encrypted data is the
Fully Homomorphic Encryption Scheme. We contribute a theoretical
presentations in a high-level computational processes that are based
on number theory and algebra that can easily be integrated and
leveraged in the Cloud computing with detail theoretic mathematical
concepts to the fully homomorphic encryption models. This
contribution enhances the full implementation of big data analytics
based cryptographic security algorithm.
Abstract: The traditional Turkish houses becoming unusable are
a result of the deterioration of the balanced interaction between users
and house (human and house) continuing during the history.
Especially depending upon the change in social structure, the houses
becoming neglected do not meet the desires of the users and do not
have the meaning but the shelter are becoming unusable and are
being destroyed.
A conservation policy should be developed and renovations should
be made in order to pass the traditional houses carrying the quality of
a cultural and historical document presenting the social structure, the
lifestyle and the traditions of its own age to the next generations and
to keep them alive.
Abstract: The characteristics of temperature distribution and
electric field in a natural rubber glove (NRG) using microwave
energy during microwave heating process are investigated
numerically and experimentally. A three-dimensional model of NRG
and microwave oven are considered in this work. The influences of
position, heating time and rotation angle of NRG on temperature
distribution and electric field are presented in details. The coupled
equations of electromagnetic wave propagation and heat transfer are
solved using the finite element method (FEM). The numerical model
is validated with an experimental study at a frequency of 2.45 GHz.
The results show that the numerical results closely match the
experimental results. Furthermore, it is found that the temperature
distribution and electric field increases with increasing heating time.
The hot spot zone appears in NRG at the tip of middle finger while
the maximum temperature occurs in case of rotation angle of NRG =
60 degree. This investigation provides the essential aspects for a
fundamental understanding of heat transport of NRG using
microwave energy in industry.
Abstract: Co metal supported on SiO2 and Al2O3 catalysts with
a metal loading varied from 30 of 70 wt.% were evaluated for
decomposition of methane to COx free hydrogen and carbon
nanomaterials. The catalytic runs were carried out from 550-800oC
under atmospheric pressure using fixed bed vertical flow reactor. The
fresh and spent catalysts were characterized by BET surface area
analyzer, XRD, SEM, TEM and TG analysis. The data showed that
50% Co/Al2O3 catalyst exhibited remarkable higher activity at 800oC
with respect to H2 production compared to rest of the catalysts.
However, the catalytic activity and durability was greatly declined at
higher temperature. The main reason for the catalytic inhibition of Co
containing SiO2 catalysts is the higher reduction temperature of
Co2SiO4. TEM images illustrate that the carbon materials with
various morphologies, carbon nanofibers (CNFs), helical-shaped
CNFs and branched CNFs depending on the catalyst composition and
reaction temperature were obtained.
Abstract: Lipases constitute one of the most important groups of
industrial enzymes that catalyze the hydrolysis of triacylglycerol to
glycerol and fatty acids. Muscarinic antagonist relieves smooth
muscle spasm of the gastrointestinal tract and effect on the
cardiovascular system. In this research the effect of a muscarinic
antagonist on the lipase activity of Pseudomonas aeruginosa was
studied. Lineweaver–Burk plot showed that the drug inhibited the
enzyme by competitive inhibition. The IC50 value (0.16 mM) and Ki
(0.03 mM) of the drug revealed the drug bound to enzyme with high
affinity. Determination of enzyme activity in various pH and
temperature showed that the maximum activity of lipase was at pH 8
and 60oC both in presence and absence of the drug.
Abstract: In this study, several crossplots of the P-impedance
with the lithology logs (gamma ray, neutron porosity, deep resistivity,
water saturation and Vp/Vs curves) were made in three available
wells, which were drilled in central part of the Blue Nile basin in
depths varies from 1460m to 1600m. These crossplots were
successful to discriminate between sand and shale when using PImpedance
values, and between the wet sand and the pay sand when
using both P-impedance and Vp/Vs together. Also some impedance
sections were converted to porosity sections using linear formula to
characterize the reservoir in terms of porosity. The used crossplots
were created on log resolution, while the seismic resolution can
identify only the reservoir, unless a 3D seismic angle stacks were
available; then it would be easier to identify the pay sand with great
confidence; through high resolution seismic inversion and
geostatistical approach when using P-impedance and Vp/Vs volumes.
Abstract: The objective of this study was to evaluate the
physical and chemical characteristics of Serra da Estrela cheese and
compare these results with those of the sensory analysis. For the
study were taken six samples of Serra da Estrela cheese produced
with 6 different ecotypes of thistle in a dairy situated in Penalva do
Castelo. The chemical properties evaluated were moisture content,
protein, fat, ash, chloride and pH; the physical properties studied
were color and texture; and finally a sensory evaluation was
undertaken. The results showed moisture varying in the range 40-
48%, protein in the range 15-20%, fat between 41-45%, ash between
3.9-5.0% and chlorides varying from 1.2 to 3.0%. The pH varied
from 4.8 to 5.4. The textural properties revealed that the crust
hardness is relatively low (maximum 7.3 N), although greater than
flesh firmness (maximum 1.7 N), and also that these cheeses are in
fact soft paste type, with measurable stickiness and intense
adhesiveness. The color analysis showed that the crust is relatively
light (L* over 50), and with a predominant yellow coloration (b*
around 20 or over) although with a slight greenish tone (a* negative).
The results of the sensory analysis did not show great variability for
most of the attributes measured, although some differences were
found in attributes such as crust thickness, crust uniformity, and
creamy flesh.
Abstract: Flours of wheat, chestnut, acorn and lupin were
evaluated in relation to phenolic compounds, antioxidant activity, and
oxalate content. At the chemical level the results show some
variability between samples by type of flour, and the sample of
chestnut flour presented the higher value of oxalate (0.00348
mg/100g) when compared to the other samples in the study.
Considering the content of phenolic compounds, the sample that
stood out was the acorn flour, having a high value of 0.812 g
AGE/100 g. All the samples presented intermediate content of
antioxidant activity and the sample that showed a slightly higher
value was the wheat flour with a value of 0.746 mM TRE/g sample.
Abstract: Emissions of atmospheric pollutants from ships and
harbour activities are a growing concern at international level given
their potential impacts on air quality and climate. These close-to-land
emissions have potential impact on local communities in terms of air
quality and health. Recent studies show that the impact of maritime
traffic to atmospheric particulate matter concentrations in several
coastal urban areas is comparable with the impact of road traffic of a
medium size town. However, several different approaches have been
used for these estimates making difficult a direct comparison of
results. In this work, an integrated approach based on emission
inventories and dedicated measurement campaigns has been applied
to give a comparable estimate of the impact of maritime traffic to
PM2.5 and particle number concentrations in three major harbours of
the Adriatic/Ionian Seas. The influences of local meteorology and of
the logistic layout of the harbours are discussed.