Abstract: This paper studies the application of a variety of
sawdust materials in the production of lightweight insulating bricks.
First, the mineralogical and chemical composition of clays was determined. Next, ceramic bricks were fabricated with different
quantities of materials (3–6 and 9 wt. % for sawdust, 65 wt. % for grey clay, 24–27 and 30 wt. % for yellow clay and 2 wt% of tuff).
These bricks were fired at 800 and 950 °C. The effect of adding this sawdust on the technological behaviour of the brick was assessed by
drying and firing shrinkage, water absorption, porosity, bulk density
and compressive strength. The results have shown that the optimum
sintering temperature is 950 °C. Below this temperature, at 950 °C,
increased open porosity was observed, which decreased the compressive strength of the bricks. Based on the results obtained, the
optimum amounts of waste were 9 wt. % sawdust of eucalyptus, 24 wt. % shaping moisture and 1.6 particle size diameter. These percentages produced bricks whose mechanical properties were
suitable for use as secondary raw materials in ceramic brick
production.
Abstract: Safety Health and Environment Code of Practice (SHE
COP) was developed to help road transportation operators to manage
its operation in a systematic and safe manner. A study was conducted
to determine the effectiveness of SHE COP implementation during
non-OPS period. The objective of the study is to evaluate the
implementations of SHE COP among bus operators during wee hour
operations. The data was collected by completing a set of checklist
after observing the activities during pre departure, during the trip, and
upon arrival. The results show that there are seven widely practiced
SHE COP elements. 22% of the buses have average speed exceeding
the maximum permissible speed on the highways (90 km/h), with
13% of the buses were travelling at the speed of more than 100 km/h.
The statistical analysis shows that there is only one significant
association which relates speeding with prior presence of
enforcement officers.
Abstract: Turbulent forced convection flow in a 2-dimensional channel over periodic grooves is numerically investigated. Finite volume method is used to study the effect of turbulence model. The range of Reynolds number varied from 10000 to 30000 for the ribheight to channel-height ratio (B/H) of 2. The downstream wall is heated by a uniform heat flux while the upstream wall is insulated. The investigation is analyzed with different types of nanoparticles such as SiO2, Al2O3, and ZnO, with water as a base fluid are used. The volume fraction is varied from 1% to 4% and the nanoparticle diameter is utilized between 20nm to 50nm. The results revealed 114% heat transfer enhancement compared to the water in a grooved channel by using SiO2 nanoparticle with volume fraction and nanoparticle diameter of 4% and 20nm respectively.
Abstract: Deep cold rolling (DCR) is a cold working process, which easily produces a smooth and work-hardened surface by plastic deformation of surface irregularities. In the present study, the influence of main deep cold rolling process parameters on the surface roughness and the hardness of AISI 4140 steel were studied by using fractional factorial design of experiments. The assessment of the surface integrity aspects on work material was done, in terms of identifying the predominant factor amongst the selected parameters, their order of significance and setting the levels of the factors for minimizing surface roughness and/or maximizing surface hardness. It was found that the ball diameter, rolling force, initial surface roughness and number of tool passes are the most pronounced parameters, which have great effects on the work piece-s surface during the deep cold rolling process. A simple, inexpensive and newly developed DCR tool, with interchangeable collet for using different ball diameters, was used throughout the experimental work presented in this paper.
Abstract: Numerical calculations of flow around a square cylinder are presented using the multi-relaxation-time lattice Boltzmann method at Reynolds number 150. The effects of upstream locations, downstream locations and blockage are investigated systematically. A detail analysis are given in terms of time-trace analysis of drag and lift coefficients, power spectra analysis of lift coefficient, vorticity contours visualizations and phase diagrams. A number of physical quantities mean drag coefficient, drag coefficient, Strouhal number and root-mean-square values of drag and lift coefficients are calculated and compared with the well resolved experimental data and numerical results available in open literature. The results had shown that the upstream, downstream and height of the computational domain are at least 7.5, 37.5 and 12 diameters of the cylinder, respectively.
Abstract: Global environmental changes lead to increased frequency and scale of natural disaster, Taiwan is under the influence of global warming and extreme weather. Therefore, the vulnerability was increased and variability and complexity of disasters is relatively enhanced. The purpose of this study is to consider the source and magnitude of hazard characteristics on the tourism industry. Using modern risk management concepts, integration of related domestic and international basic research, this goes beyond the Taiwan typhoon disaster risk assessment model and evaluation of loss. This loss evaluation index system considers the impact of extreme weather, in particular heavy rain on the tourism industry in Taiwan. Consider the extreme climate of the compound impact of disaster for the tourism industry; we try to make multi-hazard risk assessment model, strategies and suggestions. Related risk analysis results are expected to provide government department, the tourism industry asset owners, insurance companies and banking include tourist disaster risk necessary information to help its tourism industry for effective natural disaster risk management.
Abstract: Dried soy protein hydrolysate powder was added to
the burger in order to enhance the oxidative stability as well as
decreases the microbial spoilage. The soybean bioactive compounds
(soy protein hydrolysate) as antioxidant and antimicrobial were added
at level of 1, 2 and 3 %.Chemical analysis and physical properties
were affected by protein hydrolysate addition. The TBA values were
significantly affected (P < 0.05) by the storage period and the level of
soy protein hydrolysate. All the tested soybean protein hydrolysate
additives showed strong antioxidant properties. Samples of soybean
protein hydrolysate showed the lowest (P < 0.05) TBA values at each
time of storage.
The counts of all determined microbiological indicators were
significantly (P < 0.05) affected by the addition of the soybean
protein hydrolysate. Decreasing trends of different extent were also
observed in samples of the treatments for total viable counts,
Coliform, Staphylococcus aureus, yeast and molds. Storage period
was being significantly (P < 0.05) affected on microbial counts in all
samples Staphylococcus aureus were the most sensitive microbe
followed by Coliform group of the sample containing protein
hydrolysate, while molds and yeast count showed a decreasing trend
but not significant (P < 0.05) until the end of the storage period
compared with control sample. Sensory attributes were also
performed, added protein hydrolysate exhibits beany flavor which
was clear about samples of 3% protein hydrolysate.
Abstract: The main aim of this study was to examine whether
people understand indicative conditionals on the basis of syntactic
factors or on the basis of subjective conditional probability. The
second aim was to investigate whether the conditional probability of
q given p depends on the antecedent and consequent sizes or derives
from inductive processes leading to establish a link of plausible cooccurrence
between events semantically or experientially associated.
These competing hypotheses have been tested through a 3 x 2 x 2 x 2
mixed design involving the manipulation of four variables: type of
instructions (“Consider the following statement to be true", “Read the
following statement" and condition with no conditional statement);
antecedent size (high/low); consequent size (high/low); statement
probability (high/low). The first variable was between-subjects, the
others were within-subjects. The inferences investigated were Modus
Ponens and Modus Tollens. Ninety undergraduates of the Second
University of Naples, without any prior knowledge of logic or
conditional reasoning, participated in this study.
Results suggest that people understand conditionals in a syntactic
way rather than in a probabilistic way, even though the perception of
the conditional probability of q given p is at least partially involved in
the conditionals- comprehension. They also showed that, in presence
of a conditional syllogism, inferences are not affected by the
antecedent or consequent sizes. From a theoretical point of view these
findings suggest that it would be inappropriate to abandon the idea
that conditionals are naturally understood in a syntactic way for the
idea that they are understood in a probabilistic way.
Abstract: This paper presents a low-voltage low-power differential linear transconductor with near rail-to-rail input swing. Based on the current-mirror OTA topology, the proposed transconductor combines the Flipped Voltage Follower (FVF) technique to linearize the transconductor behavior that leads to class- AB linear operation and the virtual transistor technique to lower the effective threshold voltages of the transistors which offers an advantage in terms of low supply requirement. Design of the OTA has been discussed. It operates at supply voltages of about ±0.8V. Simulation results for 0.18μm TSMC CMOS technology show a good input range of 1Vpp with a high DC gain of 81.53dB and a total harmonic distortion of -40dB at 1MHz for an input of 1Vpp. The main aim of this paper is to present and compare new OTA design with high transconductance, which has a potential to be used in low voltage applications.
Abstract: The aim of this work is to analyze a viscous flow in
the axisymmetric nozzle taken into account the mesh size both in the
free stream and into the boundary layer. The resolution of the Navier-
Stokes equations is realized by using the finite volume method to
determine the supersonic flow parameters at the exit of convergingdiverging
nozzle. The numerical technique uses the Flux Vector
Splitting method of Van Leer. Here, adequate time stepping
parameter, along with CFL coefficient and mesh size level is selected
to ensure numerical convergence. The effect of the boundary layer
thickness is significant at the exit of the nozzle. The best solution is
obtained with using a very fine grid, especially near the wall, where
we have a strong variation of velocity, temperature and shear stress.
This study enabled us to confirm that the determination of boundary
layer thickness can be obtained only if the size of the mesh is lower
than a certain value limits given by our calculations.
Abstract: Human always tried to create a suitable situation for their life according to environmental conditions. In fact, geography has an important role in the shape of our living area. Iran also as a four-season country has different climate type: hot and humid, hot and dry, mid and humid, and cold; therefore, we can find different architecture styles in Iran. Gilan-s traditional architecture is a suitable sample of sustainable construction in Iran. Because the main factors of every dwelling are the climatic, social, economic and cultural effects which demonstrate the interaction between environment and people settlement. This paper was determined the interaction between environmental factors and the rural dwellings in the Gilan province. Also, traditional village (city) of Masouleh as a rare sample of rural and sustainable architecture was introduced.
Abstract: The evolution of current modeling specifications gives rise to the problem of generating automated test cases from a variety of application tools. Past endeavours on behavioural testing of UML statecharts have not systematically leveraged the potential of existing graph theory for testing of objects. Therefore there exists a need for a simple, tool-independent, and effective method for automatic test generation. An architecture, codenamed ACUTE-J (Automated stateChart Unit Testing Engine for Java), for automating the unit test generation process is presented. A sequential approach for converting UML statechart diagrams to JUnit test classes is described, with the application of existing graph theory. Research byproducts such as a universal XML Schema and API for statechart-driven testing are also proposed. The result from a Java implementation of ACUTE-J is discussed in brief. The Chinese Postman algorithm is utilised as an illustration for a run-through of the ACUTE-J architecture.
Abstract: The aim of this paper is to provide a better
understanding of the implementation of Project Management
practices by UiTM contractors to ensure project success. A
questionnaire survey was administered to 120 UiTM contractors in
Malaysia. The purpose of this method was to gather information on
the contractors- project background and project management skills. It
was found that all of the contractors had basic knowledge and
understanding of project management skills. It is suggested that a
reasonable project plan and an appropriate organizational structure
are influential factors for project success. It is recommended that the
contractors need to have an effective program of work and up to date
information system are emphasized.
Abstract: In order to study of hydropriming and halopriming on
germination and early growth stage of wheat (Triticum aestivum) an
experiment was carried out in laboratory of the Department of
Agronomy and Plant breeding, Shahrood University of Technology.
Seed treatments consisted of T1: control (untreated seeds), T2:
soaking in distilled water for 18 h (hydropriming). T3: soaking in -
1.2 MPa solution of CaSO4 for 36 h (halopriming). Germination and
early seedling growth were studied using distilled water (control) and
under osmotic potentials of -0.4, -0.8 and -1.2 MPa for NaCl and
polyethylene glycol (PEG 6000), respectively. Results showed that
Hydroprimed seeds achieved maximum germination seedling dry
weight, especially during the higher osmotic potentials. Minimum
germination was recorded at untreated seeds (control) followed by
osmopriming. Under high osmotic potentials, hydroprimed seeds had
higher GI (germination index) as compared to haloprimed or
untreated seeds. Interaction effect of seed treatment and osmotic
potential significantly affected the seedling vigour index (SVI).
Abstract: This research aims to study the preferable tourism and
the elements of choosing tourist destination from domestic tourist in
Bangkok and the nearby areas in Thailand.The data were collected by
using 1249 set of questionnaires, in mid-August 2012. The result
illustrates that religious destinations are the most preferable places
for the tourist. The average expense per travel is approximately 47
USD a time. Travellers travel based on the advertisement in the
television and internet and their decisions is based on the reputation
of the destinations.
The result on a place dimension demonstrates the neatness and
well managed location play a crucial role on tourist destination.
Gender, age, marriage status and their origins are affecting their
spending and travelling behaviour. The researcher reckon that
providing the area of arcade, selling the souvenir and promoting
tourism among a young professional group would be an important
key follow the income distribution policy, including managing the
destination to welcome the family group, which the result is to
identified as the highest spending.
Abstract: The purpose of this study is to suggest energy efficient
routing for ad hoc networks which are composed of nodes with limited
energy. There are diverse problems including limitation of energy
supply of node, and the node energy management problem has been
presented. And a number of protocols have been proposed for energy
conservation and energy efficiency. In this study, the critical point of
the EA-MPDSR, that is the type of energy efficient routing using only
two paths, is improved and developed. The proposed TP-MESR uses
multi-path routing technique and traffic prediction function to increase
number of path more than 2. It also verifies its efficiency compared to
EA-MPDSR using network simulator (NS-2). Also, To give a
academic value and explain protocol systematically, research
guidelines which the Hevner(2004) suggests are applied. This
proposed TP-MESR solved the existing multi-path routing problem
related to overhead, radio interference, packet reassembly and it
confirmed its contribution to effective use of energy in ad hoc
networks.
Abstract: In this paper, we study FPGA implementation of a
novel supra-optimal receiver diversity combining technique,
generalized maximal ratio combining (GMRC), for wireless
transmission over fading channels in SIMO systems. Prior
published results using ML-detected GMRC diversity signal
driven by BPSK showed superior bit error rate performance to
the widely used MRC combining scheme in an imperfect
channel estimation (ICE) environment. Under perfect channel
estimation conditions, the performance of GMRC and MRC
were identical. The main drawback of the GMRC study was
that it was theoretical, thus successful FPGA implementation
of it using pipeline techniques is needed as a wireless
communication test-bed for practical real-life situations.
Simulation results showed that the hardware implementation
was efficient both in terms of speed and area. Since diversity
combining is especially effective in small femto- and picocells,
internet-associated wireless peripheral systems are to
benefit most from GMRC. As a result, many spinoff
applications can be made to the hardware of IP-based 4th
generation networks.
Abstract: Having considered tactile sensing and palpation of a
surgeon in order to detect kidney stone during open surgery; we
present the 2D model of nephrolithiasis (two dimensional model of
kidney containing a simulated stone). The effects of stone existence
that appear on the surface of kidney (because of exerting mechanical
load) are determined. Using Finite element method, it is illustrated
that the created stress patterns on the surface of kidney and stress
graphs not only show existence of stone inside kidney, but also show
its exact location.
Abstract: An investigation of the process of deformation hardening and evolution of deformation defect medium in dispersion-hardened materials with face centered cubic matrices and nanoparticles was done. Mathematical model including balance equation for the deformation defects was used.
Abstract: The most common type of controller being used in
the industry is PI(D) controller which has been used since 1945 and
is still being widely used due to its efficiency and simplicity. In
most cases, the PI(D) controller was tuned without taking into
consideration of the effect of actuator saturation. In real processes,
the most common actuator which is valve will act as constraint and
restrict the controller output. Since the controller is not designed to
encounter saturation, the process may windup and consequently
resulted in large oscillation or may become unstable. Usually, an
antiwindup compensator is added to the feedback control loop to
reduce the deterioration effect of integral windup. This research
aims to specifically control processes with constraints. The
proposed method was applied to two different types of food
processes, which are blending and spray drying. Simulations were
done using MATLAB and the performances of the proposed
method were compared with other conventional methods. The
proposed technique was able to control the processes and avoid
saturation such that no anti windup compensator is needed.