Abstract: In this study, the reduction of Cr(VI) by use of scrap
iron, a cheap and locally available industrial waste, was investigated
in continuous system. The greater scrap iron efficiency observed for
the first two sections of the column filling indicate that most of the
reduction process was carried out in the bottom half of the column
filling. This was ascribed to a constant decrease of Cr(VI)
concentration inside the filling, as the water front passes from the
bottom to the top end of the column. While the bottom section of the
column filling was heavily passivated with secondary mineral phases,
the top section was less affected by the passivation process; therefore
the column filling would likely ensure the reduction of Cr(VI) for
time periods longer than 216 hours. The experimental results indicate
that fixed beds columns packed with scrap iron could be successfully
used for the first step of Cr(VI) polluted wastewater treatment.
However, the mass of scrap iron filling should be carefully estimated
since it significantly affects the Cr(VI) reduction efficiency.
Abstract: In this paper, a Gaussian multiple input multiple output multiple eavesdropper (MIMOME) channel is considered where a transmitter communicates to a receiver in the presence of an eavesdropper. We present a technique for determining the secrecy capacity of the multiple input multiple output (MIMO) channel under Gaussian noise. We transform the degraded MIMOME channel into multiple single input multiple output (SIMO) Gaussian wire-tap channels and then use scalar approach to convert it into two equivalent multiple input single output (MISO) channels. The secrecy capacity model is then developed for the condition where the channel state information (CSI) for main channel only is known to the transmitter. The results show that the secret communication is possible when the eavesdropper channel noise is greater than a cutoff noise level. The outage probability is also analyzed of secrecy capacity is also analyzed. The effect of fading and outage probability is also analyzed.
Abstract: End-substitution of quarterthiophene and sexithiophene with hexyl groups leads to highly soluble conjugated oligomers,DZ-dihexylquarterthiophene (DH-4T) and DZ-dihexylsexithiophene (DH-6T). We have characterized these oligomers for optical and electrical properties. We fabricated an organic thin film transistor (OTFT) using the above two air-stable p-type organic semiconductor materials. We obtained a stable characteristic curve. The field effect mobility, Pwas calculated to be 3.2910-4 cm2/Vs for DH-6T based OTFT; while the DH-4T based OTFT had 1.8810-5 cm2/Vs.KeywordsOrganic thin film transistor, DZ-dihexylquarterthiophene, DZ-dihexylsexithiophene.
Abstract: This paper explores the social and political imperatives in the sphere of public policy relating to social justice. In India, the colonial legacy and post-colonial social and political pressures sustained the appropriation of 'caste' category in allocating public resources to the backward class of citizens. For several reasons, 'economic' category could not be placed in allocating resources. This paper examines the reasons behind the deliberative exercises and formulating policies and seeks an alternative framework in realizing social justice in terms of a unified category. This attempt can be viewed as a reconciliation of traditional and modern values for a viable alternative in public policy making.
Abstract: Internet access is a vital part of the modern world and an important tool in the education of our children. It is present in schools, homes and even shopping malls. Mastering the use of the internet is likely to be an important skill for those entering the job markets of the future. An internet user can be anyone he or she wants to be in an online chat room, or play thrilling and challenging games against other players from all corners of the globe. It seems at present time (or near future) for many people relationships in the real world may be neglected as those in the virtual world increase in importance. Internet is provided a fast mode of transportation caused freedom from family bonds and mixing with different cultures and new communities. This research is an attempt to study effect of Internet on Social capital. For this purpose a survey technique on the sample size amounted 168 students of Payame Noor University of Kermanshah city in country of Iran were considered. Degree of social capital is moderate. With the help of the Multi-variable Regression, variables of Iranian message attractive, Interest to internet with effect of positive and variable Creating a cordial atmosphere with negative effect be significant.
Abstract: WiMAX and Wi-Fi are considered as the promising
broadband access solutions for wireless MAN’s and LANs,
respectively. In the recent works WiMAX is considered suitable as a
backhaul service to connect multiple dispersed Wi-Fi ‘hotspots’.
Hence a new integrated WiMAX/Wi-Fi architecture has been
proposed in literatures. In this paper the performance of an integrated
WiMAX/Wi-Fi network has been investigated by streaming a video
conference application. The difference in performance between the
two protocols is compared with respect to video conferencing. The
Heterogeneous network was simulated in the OPNET simulator.
Abstract: With the rapid advanced of technology, the industrial processes become increasingly demanding, from the point of view, power quality and controllability. The advent of multi levels inverters responds partially to these requirements. But actually, the new generation of multi-cells inverters permits to reach more performances, since, it offers more voltage levels. The disadvantage in the increase of voltage levels by the number of cells in cascades is on account of series igbts synchronisation loss, from where, a limitation of cells in cascade to 4. Regarding to these constraints, a new topology is proposed in this paper, which increases the voltage levels of the three-cell inverter from 4 to 8; with the same number of igbts, and using less stored energy in the flaying capacitors. The details of operation and modelling of this new inverter structure are also presented, then tested thanks to a three phase induction motor. KeywordsFlaying capacitors, Multi-cells inverter, pwm, switchers, modelling.
Abstract: A model based fault detection and diagnosis
technique for DC motor is proposed in this paper. Fault detection
using Kalman filter and its different variants are compared. Only
incipient faults are considered for the study. The Kalman Filter
iterations and all the related computations required for fault detection
and fault confirmation are presented. A second order linear state
space model of DC motor is used for this work. A comparative
assessment of the estimates computed from four different observers
and their relative performance is evaluated.
Abstract: In this paper we propose a new approach to constructing the Delaunay Triangulation and the optimum algorithm for the case of multidimensional spaces (d ≥ 2). Analysing the modern state, it is possible to draw a conclusion, that the ideas for the existing effective algorithms developed for the case of d ≥ 2 are not simple to generalize on a multidimensional case, without the loss of efficiency. We offer for the solving this problem an effective algorithm that satisfies all the given requirements. But theoretical complexity of the problem it is impossible to improve as the Worst - Case Optimality for algorithms of solving such a problem is proved.
Abstract: Modern spatial database management systems require a unique Spatial Access Method (SAM) in order solve complex spatial quires efficiently. In this case the spatial data structure takes a prominent place in the SAM. Inadequate data structure leads forming poor algorithmic choices and forging deficient understandings of algorithm behavior on the spatial database. A key step in developing a better semantic spatial object data structure is to quantify the performance effects of semantic and outlier detections that are not reflected in the previous tree structures (R-Tree and its variants). This paper explores a novel SSRO-Tree on SAM to the Topo-Semantic approach. The paper shows how to identify and handle the semantic spatial objects with outlier objects during page overflow/underflow, using gain/loss metrics. We introduce a new SSRO-Tree algorithm which facilitates the achievement of better performance in practice over algorithms that are superior in the R*-Tree and RO-Tree by considering selection queries.
Abstract: The degradation of selected pharmaceuticals in some
water matrices was studied by using several chemical treatments. The
pharmaceuticals selected were the beta-blocker metoprolol, the
nonsteroidal anti-inflammatory naproxen, the antibiotic amoxicillin,
and the analgesic phenacetin; and their degradations were conducted
by using UV radiation alone, ozone, Fenton-s reagent, Fenton-like
system, photo-Fenton system, and combinations of UV radiation and
ozone with H2O2, TiO2, Fe(II), and Fe(III). The water matrices, in
addition to ultra-pure water, were a reservoir water, a groundwater,
and two secondary effluents from two municipal WWTP. The results
reveal that the presence of any second oxidant enhanced the
oxidation rates, with the systems UV/TiO2 and O3/TiO2 providing the
highest degradation rates. It is also observed in most of the
investigated oxidation systems that the degradation rate followed the
sequence: amoxicillin > naproxen > metoprolol > phenacetin. Lower
rates were obtained with the pharmaceuticals dissolved in natural
waters and secondary effluents due to the organic matter present
which consume some amounts of the oxidant agents.
Abstract: Simultaneous determination of multicomponents of phenol, resorcinol and catechol with a chemometric technique a PCranking artificial neural network (PCranking-ANN) algorithm is reported in this study. Based on the data correlation coefficient method, 3 representative PCs are selected from the scores of original UV spectral data (35 PCs) as the original input patterns for ANN to build a neural network model. The results obtained by iterating 8000 .The RMSEP for phenol, resorcinol and catechol with PCranking- ANN were 0.6680, 0.0766 and 0.1033, respectively. Calibration matrices were 0.50-21.0, 0.50-15.1 and 0.50-20.0 μg ml-1 for phenol, resorcinol and catechol, respectively. The proposed method was successfully applied for the determination of phenol, resorcinol and catechol in synthetic and water samples.
Abstract: Laser engraving is a manufacturing method for those applications where previously Electrical Discharge Machining (EDM) was the only choice. Laser engraving technology removes material layer-by-layer and the thickness of layers is usually in the range of few microns. The aim of the present work is to investigate the influence of the process parameters on the surface quality when machined by laser engraving. The examined parameters were: the pulse frequency, the beam speed and the layer thickness. The surface quality was determined by the surface roughness for every set of parameters. Experimental results on Al7075 material showed that the surface roughness strictly depends on the process parameters used.
Abstract: The aim of this study was to develop a dynamic cardiac phantom for quality control in myocardial scintigraphy. The dynamic heart phantom constructed only contained the left ventricle, made of elastic material (latex), comprising two cavities: one internal and one external. The data showed a non-significant variation in the values of left ventricular ejection fraction (LVEF) obtained by varying the heart rate. It was also possible to evaluate the ejection fraction (LVEF) through different arrays of image acquisition and to perform an intercomparison of LVEF by two different scintillation cameras. The results of the quality control tests were satisfactory, showing that they can be used as parameters in future assessments. The new dynamic heart phantom was demonstrated to be effective for use in LVEF measurements. Therefore, the new heart simulator is useful for the quality control of scintigraphic cameras.
Abstract: This paper addresses the problem of recognizing and
interpreting the behavior of human workers in industrial
environments for the purpose of integrating humans in software
controlled manufacturing environments. In this work we propose a
generic concept in order to derive solutions for task-related manual
production applications. Thus, we are able to use a versatile concept
providing flexible components and being less restricted to a specific
problem or application. We instantiate our concept in a spot welding
scenario in which the behavior of a human worker is interpreted
when performing a welding task with a hand welding gun. We
acquire signals from inertial sensors, video cameras and triggers and
recognize atomic actions by using pose data from a marker based
video tracking system and movement data from inertial sensors.
Recognized atomic actions are analyzed on a higher evaluation level
by a finite state machine.
Abstract: To judge whether the memristor can be interpreted as
the fourth fundamental circuit element, we propose a variable-relation
criterion of fundamental circuit elements. According to the criterion,
we investigate the nature of three fundamental circuit elements and the
memristor. From the perspective of variables relation, the memristor
builds a direct relation between the voltage across it and the current
through it, instead of a direct relation between the magnetic flux and
the charge. Thus, it is better to characterize the memristor and the
resistor as two special cases of the same fundamental circuit element,
which is the memristive system in Chua-s new framework. Finally, the
definition of memristor is refined according to the difference between
the magnetic flux and the flux linkage.
Abstract: A new mechanism responsible for structural life
consumption due to resonant fatigue in turbine blades, or vanes, is
presented and explained. A rotating blade or vane in a gas turbine can
change its contour due to erosion and/or material build up, in any of
these instances, the surface pressure distribution occurring on the
suction and pressure sides of blades-vanes can suffer substantial
modification of their pressure and temperatures envelopes and flow
characteristics. Meanwhile, the relative rotation between the blade
and duct vane while the pressurized gas flows and the consequent
wake crossings, will induce a fluctuating thrust force or lift that will
excite the blade.
An actual totally used up set of vane-blade components in a HP
turbine power stage in a gas turbine is analyzed. The blade suffered
some material erosion mostly at the trailing edge provoking a
peculiar surface pressure envelope which evolved as the relative
position between the vane and the blade passed in front of each other.
Interestingly preliminary modal analysis for this eroded blade
indicates several natural frequencies within the aeromechanic power
spectrum, moreover, the highest frequency component is 94% of one
natural frequency indicating near resonant condition.
Independently of other simultaneously occurring fatigue cycles
(such as thermal, centrifugal stresses).
Abstract: Until recently it would have been unusual to consider classifying population movements and refugees as security problem. However, efforts at shaping our world to make ourselves secure have paradoxically led to ever greater insecurity. The feeling of uncertainty, pertinent throughout all discourses of security, has led to the creation of security production into seemingly benign routines of everyday life. Yet, the paper argues, neither of security discourses accounted for, disclosed and challenged the fundamental aporias embedded in Western security narratives. In turn, the paper aims to unpick the conventional security wisdom, which is haunted with strong ontologies, embedded in the politics of Orientalism, and (in)security nexus. The paper concludes that current security affair conceals the integral impossibility of fulfilling its very own promise of assured security. The paper also provides suggestions about alternative security discourse based on mutual dialogue.
Abstract: Linear Discrimination Analysis (LDA) is a linear
solution for classification of two classes. In this paper, we propose a
variant LDA method for multi-class problem which redefines the
between class and within class scatter matrices by incorporating a
weight function into each of them. The aim is to separate classes as
much as possible in a situation that one class is well separated from
other classes, incidentally, that class must have a little influence on
classification. It has been suggested to alleviate influence of classes
that are well separated by adding a weight into between class scatter
matrix and within class scatter matrix. To obtain a simple and
effective weight function, ordinary LDA between every two classes
has been used in order to find Fisher discrimination value and passed
it as an input into two weight functions and redefined between class
and within class scatter matrices. Experimental results showed that
our new LDA method improved classification rate, on glass, iris and
wine datasets, in comparison to different versions of LDA.
Abstract: A analysis on the conventional the blood pressure estimation method using an oscillometric sphygmomanometer was
performed through a computer simulation using an arterial pressure-volume (APV) model. Traditionally, the maximum amplitude algorithm (MAP) was applied on the oscillation waveforms of the APV model to obtain the mean arterial pressure and the characteristic ratio. The estimation of mean arterial pressure and
characteristic ratio was significantly affected with the shape of the blood pressure waveforms and the cutoff frequency of high-pass filter
(HPL) circuitry. Experimental errors are due to these effects when estimating blood pressure. To find out an algorithm independent from
the influence of waveform shapes and parameters of HPL, the volume
oscillation of the APV model and the phase shift of the oscillation with fast fourier transform (FFT) were testified while increasing the cuff
pressure from 1 mmHg to 200 mmHg (1 mmHg per second). The phase shift between the ranges of volume oscillation was then only observed between the systolic and the diastolic blood pressures. The same results were also obtained from the simulations performed on two different the arterial blood pressure waveforms and one
hyperthermia waveform.