Abstract: In this paper, a target signal detection method using
multiple signal classification (MUSIC) algorithm is proposed. The
MUSIC algorithm is a subspace-based direction of arrival (DOA)
estimation method. The algorithm detects the DOAs of multiple
sources using the inverse of the eigenvalue-weighted eigen spectra. To
apply the algorithm to target signal detection for GSC-based
beamforming, we utilize its spectral response for the target DOA in
noisy conditions. For evaluation of the algorithm, the performance of
the proposed target signal detection method is compared with that of
the normalized cross-correlation (NCC), the fixed beamforming, and
the power ratio method. Experimental results show that the proposed
algorithm significantly outperforms the conventional ones in receiver
operating characteristics(ROC) curves.
Abstract: This article proposes a current-mode square-rooting
circuit using current follower transconductance amplifier (CTFA).
The amplitude of the output current can be electronically controlled
via input bias current with wide input dynamic range. The proposed
circuit consists of only single CFTA. Without any matching
conditions and external passive elements, the circuit is then
appropriate for an IC architecture. The magnitude of the output signal
is temperature-insensitive. The PSpice simulation results are
depicted, and the given results agree well with the theoretical
anticipation. The power consumption is approximately 1.96mW at
±1.5V supply voltages.
Abstract: In this paper, a block code to minimize the peak-toaverage
power ratio (PAPR) of orthogonal frequency division
multiplexing (OFDM) signals is proposed. It is shown that cyclic
shift and codeword inversion cause not change to peak envelope
power. The encoding rule for the proposed code comprises of
searching for a seed codeword, shifting the register elements, and
determining codeword inversion, eliminating the look-up table for
one-to-one correspondence between the source and the coded data.
Simulation results show that OFDM systems with the proposed code
always have the minimum PAPR.
Abstract: A fast settling multipath CMOS OTA for high speed
switched capacitor applications is presented here. With the basic
topology similar to folded-cascode, bandwidth and DC gain of the
OTA are enhanced by adding extra paths for signal from input to
output. Designed circuit is simulated with HSPICE using level 49
parameters (BSIM 3v3) in 0.35mm standard CMOS technology. DC
gain achieved is 56.7dB and Unity Gain Bandwidth (UGB) obtained
is 1.15GHz. These results confirm that adding extra paths for signal
can improve DC gain and UGB of folded-cascode significantly.
Abstract: In this paper an alternative analysis in the time
domain is described and the results of the interpolation process are
presented by means of functions that are based on the rule of
conditional mathematical expectation and the covariance function. A
comparison between the interpolation error caused by low order
filters and the classic sinc(t) truncated function is also presented.
When fewer samples are used, low-order filters have less error. If the
number of samples increases, the sinc(t) type functions are a better
alternative. Generally speaking there is an optimal filter for each
input signal which depends on the filter length and covariance
function of the signal. A novel scheme of work for adaptive
interpolation filters is also presented.
Abstract: In this paper, an automatic determination algorithm for nuclear magnetic resonance (NMR) spectra of the metabolites in the living body by magnetic resonance spectroscopy (MRS) without human intervention or complicated calculations is presented. In such method, the problem of NMR spectrum determination is transformed into the determination of the parameters of a mathematical model of the NMR signal. To calculate these parameters efficiently, a new model called modified Hopfield neural network is designed. The main achievement of this paper over the work in literature [30] is that the speed of the modified Hopfield neural network is accelerated. This is done by applying cross correlation in the frequency domain between the input values and the input weights. The modified Hopfield neural network can accomplish complex dignals perfectly with out any additinal computation steps. This is a valuable advantage as NMR signals are complex-valued. In addition, a technique called “modified sequential extension of section (MSES)" that takes into account the damping rate of the NMR signal is developed to be faster than that presented in [30]. Simulation results show that the calculation precision of the spectrum improves when MSES is used along with the neural network. Furthermore, MSES is found to reduce the local minimum problem in Hopfield neural networks. Moreover, the performance of the proposed method is evaluated and there is no effect on the performance of calculations when using the modified Hopfield neural networks.
Abstract: We discuss the signal detection through nonlinear
threshold systems. The detection performance is assessed by the
probability of error Per . We establish that: (1) when the signal is
complete suprathreshold, noise always degrades the signal detection
both in the single threshold system and in the parallel array of
threshold devices. (2) When the signal is a little subthreshold, noise
degrades signal detection in the single threshold system. But in the
parallel array, noise can improve signal detection, i.e., stochastic
resonance (SR) exists in the array. (3) When the signal is predominant
subthreshold, noise always can improve signal detection and SR
always exists not only in the single threshold system but also in the
parallel array. (4) Array can improve signal detection by raising the
number of threshold devices. These results extend further the
applicability of SR in signal detection.
Abstract: In this work, we present a comparison between
different techniques of image compression. First, the image is
divided in blocks which are organized according to a certain scan.
Later, several compression techniques are applied, combined or
alone. Such techniques are: wavelets (Haar's basis), Karhunen-Loève
Transform, etc. Simulations show that the combined versions are the
best, with minor Mean Squared Error (MSE), and higher Peak Signal
to Noise Ratio (PSNR) and better image quality, even in the presence
of noise.
Abstract: The use of Inverse Discrete Fourier Transform (IDFT) implemented in the form of Inverse Fourier Transform (IFFT) is one of the standard method of reconstructing Magnetic Resonance Imaging (MRI) from uniformly sampled K-space data. In this tutorial, three of the major problems associated with the use of IFFT in MRI reconstruction are highlighted. The tutorial also gives brief introduction to MRI physics; MRI system from instrumentation point of view; K-space signal and the process of IDFT and IFFT for One and two dimensional (1D and 2D) data.
Abstract: Functional gastrointestinal disorders affect millions of people spread all age regardless of race and sex. There are, however, rare diagnostic methods for the functional gastrointestinal disorders because functional disorders show no evidence of organic and physical causes. Our research group identified recently that the gastrointestinal tract well in the patients with the functional gastrointestinal disorders becomes more rigid than healthy people when palpating the abdominal regions overlaying the gastrointestinal tract. Aim of this study is, therefore, to develop a diagnostic system for the functional gastrointestinal disorders based on ultrasound technique, which can quantify the characteristic above related to the rigidity of the gastrointestinal tract well. Ultrasound system was designed. The system consisted of transmitter, ultrasonic transducer, receiver, TGC, and CPLD, and verified via a phantom test. For the phantom test, ten soft-tissue specimens were harvested from porcine. Five of them were then treated chemically to mimic a rigid condition of gastrointestinal tract well, which was induced by functional gastrointestinal disorders. Additionally, the specimens were tested mechanically to identify if the mimic was reasonable. The customized ultrasound system was finally verified through application to human subjects with/without functional gastrointestinal disorders (Normal and Patient Groups). It was identified from the mechanical test that the chemically treated specimens were more rigid than normal specimen. This finding was favorably compared with the result obtained from the phantom test. The phantom test also showed that ultrasound system well described the specimen geometric characteristics and detected an alteration in the specimens. The maximum amplitude of the ultrasonic reflective signal in the rigid specimens (0.2±0.1Vp-p) at the interface between the fat and muscle layers was explicitly higher than that in the normal specimens (0.1±0.0Vp-p). Clinical tests using our customized ultrasound system for human subject showed that the maximum amplitudes of the ultrasonic reflective signals near to the gastrointestinal tract well for the patient group (2.6±0.3Vp-p) were generally higher than those in normal group (0.1±0.2Vp-p). Here, maximum reflective signals was appeared at 20mm depth approximately from abdominal skin for all human subjects, corresponding to the location of the boundary layer close to gastrointestinal tract well. These results suggest that newly designed diagnostic system based on ultrasound technique may diagnose enough the functional gastrointestinal disorders.
Abstract: This paper addresses control of commutation of switched reluctance (SR) motor without the use of a physical position detector. Rotor position detection schemes for SR motor based on magnetisation characteristics of the motor use normal excitation or applied current /voltage pulses. The resulting schemes are referred to as passive or active methods respectively. The research effort is in realizing an economical sensorless SR rotor position detector that is accurate, reliable and robust to suit a particular application. An effective and reliable means of generating commutation signals of an SR motor based on inductance profile of its stator windings determined using active probing technique is presented. The scheme has been validated online using a 4-phase 8/6 SR motor and an 8-bit processor.
Abstract: The design of chaos-based secure communication
via synchronized modified Chua-s systems is investigated in
this paper. A continuous control law is proposed to ensure
synchronization of the master and slave modified Chua-s
systems by using the variable structure control technique.
Particularly, the concept of extended systems is introduced
such that a continuous control input is obtained to avoid
chattering phenomenon. Then, it becomes possible to ensure
that the message signal embedded in the transmitter can be
recovered in the receiver.
Abstract: The approach based on the wavelet transform has
been widely used for image denoising due to its multi-resolution
nature, its ability to produce high levels of noise reduction and the
low level of distortion introduced. However, by removing noise, high
frequency components belonging to edges are also removed, which
leads to blurring the signal features. This paper proposes a new
method of image noise reduction based on local variance and edge
analysis. The analysis is performed by dividing an image into 32 x 32
pixel blocks, and transforming the data into wavelet domain. Fast
lifting wavelet spatial-frequency decomposition and reconstruction is
developed with the advantages of being computationally efficient and
boundary effects minimized. The adaptive thresholding by local
variance estimation and edge strength measurement can effectively
reduce image noise while preserve the features of the original image
corresponding to the boundaries of the objects. Experimental results
demonstrate that the method performs well for images contaminated
by natural and artificial noise, and is suitable to be adapted for
different class of images and type of noises. The proposed algorithm
provides a potential solution with parallel computation for real time
or embedded system application.
Abstract: Frequency domain independent component analysis has
a scaling indeterminacy and a permutation problem. The scaling
indeterminacy can be solved by use of a decomposed spectrum. For
the permutation problem, we have proposed the rules in terms of gain
ratio and phase difference derived from the decomposed spectra and
the source-s coarse directions.
The present paper experimentally clarifies that the gain ratio and
the phase difference work effectively in a real environment but their
performance depends on frequency bands, a microphone-space and
a source-microphone distance. From these facts it is seen that it is
difficult to attain a perfect solution for the permutation problem in a
real environment only by either the gain ratio or the phase difference.
For the perfect solution, this paper gives a solution to the problems
in a real environment. The proposed method is simple, the amount of
calculation is small. And the method has high correction performance
without depending on the frequency bands and distances from source
signals to microphones. Furthermore, it can be applied under the real
environment. From several experiments in a real room, it clarifies
that the proposed method has been verified.
Abstract: Different pseudo-random or pseudo-noise (PN) as well as orthogonal sequences that can be used as spreading codes for code division multiple access (CDMA) cellular networks or can be used for encrypting speech signals to reduce the residual intelligence are investigated. We briefly review the theoretical background for direct sequence CDMA systems and describe the main characteristics of the maximal length, Gold, Barker, and Kasami sequences. We also discuss about variable- and fixed-length orthogonal codes like Walsh- Hadamard codes. The equivalence of PN and orthogonal codes are also derived. Finally, a new PN sequence is proposed which is shown to have certain better properties than the existing codes.
Abstract: Oil debris signal generated from the inductive oil
debris monitor (ODM) is useful information for machine condition
monitoring but is often spoiled by background noise. To improve the
reliability in machine condition monitoring, the high-fidelity signal
has to be recovered from the noisy raw data. Considering that the noise
components with large amplitude often have higher frequency than
that of the oil debris signal, the integral transform is proposed to
enhance the detectability of the oil debris signal. To cancel out the
baseline wander resulting from the integral transform, the empirical
mode decomposition (EMD) method is employed to identify the trend
components. An optimal reconstruction strategy including both
de-trending and de-noising is presented to detect the oil debris signal
with less distortion. The proposed approach is applied to detect the oil
debris signal in the raw data collected from an experimental setup. The
result demonstrates that this approach is able to detect the weak oil
debris signal with acceptable distortion from noisy raw data.
Abstract: This paper presents the development of an active
vibration control using direct adaptive controller to suppress the
vibration of a flexible beam system. The controller is realized based
on linear parametric form. Differential evolution optimisation
algorithm is used to optimize the controller using single objective
function by minimizing the mean square error of the observed
vibration signal. Furthermore, an alternative approach is developed to
systematically search for the best controller model structure together
with it parameter values. The performance of the control scheme is
presented and analysed in both time and frequency domain.
Simulation results demonstrate that the proposed scheme is able to
suppress the unwanted vibration effectively.
Abstract: The purpose of this paper is to present a Dynamic
Time Warping technique which reduces significantly the data
processing time and memory size of multi-dimensional time series
sampled by the biometric smart pen device BiSP. The acquisition
device is a novel ballpoint pen equipped with a diversity of sensors
for monitoring the kinematics and dynamics of handwriting
movement. The DTW algorithm has been applied for time series
analysis of five different sensor channels providing pressure,
acceleration and tilt data of the pen generated during handwriting on
a paper pad. But the standard DTW has processing time and memory
space problems which limit its practical use for online handwriting
recognition. To face with this problem the DTW has been applied to
the sum of the five sensor signals after an adequate down-sampling
of the data. Preliminary results have shown that processing time and
memory size could significantly be reduced without deterioration of
performance in single character and word recognition. Further
excellent accuracy in recognition was achieved which is mainly due
to the reduced dynamic time warping RDTW technique and a novel
pen device BiSP.
Abstract: Overhead conveyor systems are in use in many installations around the world, meeting the widest range of applications possible. Overhead conveyor systems are particularly preferred in automotive industry but also at post offices. Overhead conveyor systems must always be integrated with a logistical process by finding the best way for a cheaper material flow in order to guarantee precise and fast workflows. With their help, any transport can take place without wasting ground and space, without excessive company capacity, lost or damaged products, erroneous delivery, endless travels and without wasting time. Ultra-light overhead conveyor systems are rope-based conveying systems with individually driven vehicles. The vehicles can move automatically on the rope and this can be realized by energy and signals. Crossings are realized by switches. Ultra-light overhead conveyor systems provide optimal material flow, which produces profit and saves time. This article introduces two new ultra-light overhead conveyor designs in logistics and explains their components. According to the explanation of the components, scenarios are created by means of their technical characteristics. The scenarios are visualized with the help of CAD software. After that, assumptions are made for application area. According to these assumptions scenarios are visualized. These scenarios help logistics companies achieve lower development costs as well as quicker market maturity.
Abstract: Deep Brain Stimulation or DBS is the second solution
for Parkinson's Disease. Its three parameters are: frequency, pulse
width and voltage. They must be optimized to achieve successful
treatment. Nowadays it is done clinically by neurologists and there is
not certain numerical method to detect them. The aim of this research
is to introduce simulation and modeling of Parkinson's Disease
treatment as a computational procedure to select optimum voltage.
We recorded finger tremor signals of some Parkinsonian patients
under DBS treatment at constant frequency and pulse width but
variable voltages; then, we adapted a new model to fit these data. The
optimum voltages obtained by data fitting results were the same as
neurologists- commented voltages, which means modeling can be
used as an engineering method to select optimum stimulation
voltages.