Abstract: We present a label-free biosensor based on
electrochemical impedance spectroscopy for the detection of proinflammatory
cytokine Tumor Necrosis Factor (TNF-α). Secretion of
TNF-α has been correlated to the onset of various diseases including
rheumatoid arthritis, Crohn-s disease etc. Gold electrodes were
patterned on a silicon substrate and self assembled monolayer of
dithiobis-succinimidyl propionate was used to develop the biosensor
which achieved a detection limit of ~57fM. A linear relationship was
also observed between increasing TNF-α concentrations and chargetransfer
resistance within a dynamic range of 1pg/ml – 1ng/ml.
Abstract: Analytical investigation of the sedimentation
processes in the river engineering and hydraulic structures is of vital
importance as this can affect water supply for the cultivating lands in
the command area. The reason being that gradual sediment formation
behind the reservoir can reduce the nominal capacity of these dams.
The aim of the present paper is to analytically investigate
sedimentation process along the river course and behind the storage
reservoirs in general and the Eastern Intake of the Dez Diversion weir
in particular using the SHARC software. Results of the model
indicated the water level at 115.97m whereas the real time
measurement from the river cross section was 115.98 m which
suggests a significantly close relation between them. The average
transported sediment load in the river was measured at 0.25mm ,
from which it can be concluded that nearly 100% of the suspended
loads in river are moving which suggests no sediment settling but
indicates that almost all sediment loads enters into the intake. It was
further showed the average sediment diameter entering the intake to
be 0.293 mm which in turn suggests that about 85% of suspended
sediments in the river entre the intake. Comparison of the results
from the SHARC model with those obtained form the SSIIM
software suggests quite similar outputs but distinguishing the
SHARC model as more appropriate for the analysis of simpler
problems than other model.
Abstract: This paper presents the impact study of apparent
reactance injected by series Flexible AC Transmission System
(FACTS) i.e. Thyristor Controlled Series Reactor (TCSR) on the
measured impedance of a 400 kV single electrical transmission line
in the presence of phase to earth fault with fault resistance. The study
deals with an electrical transmission line of Eastern Algerian
transmission networks at Group Sonelgaz (Algerian Company of
Electrical and Gas) compensated by TCSR connected at midpoint of
the line. This compensator used to inject active and reactive powers
is controlled by three TCSR-s. The simulations results investigate the
impacts of the TCSR on the parameters of short circuit calculation
and parameters of measured impedance by distance relay in the
presence of earth fault for three cases study.
Abstract: As a part of routine oesophageal HDR Brachytherapy procedure, treatment planning takes about 45 minutes while patients are under light sedation. Some patients may suffer gagging and/or spasms before the 90-minute brachytherapy procedure complete, and the treatment may need to be aborted. A pre-prepared plan generated before patient’s sedation may reduce the brachytherapy procedure time by 40 minutes. This paper reports rationality and evidence of pre-prepared treatment plans. A retrospective study of 28 patients confirms that pre-prepared plans would be acceptable for all reviewed patients. The rationality is further confirmed by a systemic study with a wide range of applicator curvature and treatment volume. Detailed comparison between CT based treatment plans and pre-prepared plans are discussed. The argument holds for endobronchial HDR brachytherapy too. With the above evidence, pre-prepared plans have been used for all oesophageal and endobronchial HDR brachytherapy cases in our clinic.
Abstract: In this paper, we focus on the use of knowledge bases
in two different application areas – control of systems with unknown
or strongly nonlinear models (i.e. hardly controllable by the classical
methods), and robot motion planning in eight directions. The first
one deals with fuzzy logic and the paper presents approaches for
setting and aggregating the rules of a knowledge base. Te second one
is concentrated on a case-based reasoning strategy for finding the
path in a planar scene with obstacles.
Abstract: This paper presents a new type of mechanism and trajectory planning strategy for bipedal walking robot. The newly designed mechanism is able to improve the performance of bipedal walking robot in terms of energy efficiency and weight reduction by utilizing minimum number of actuators. The usage of parallelogram mechanism eliminates the needs of having an extra actuator at the knee joint. This mechanism works together with the joint space trajectory planning in order to realize straight legged walking which cannot be achieved by conventional inverse kinematics trajectory planning due to the singularity. The effectiveness of the proposed strategy is confirmed by computer simulation results.
Abstract: Two-dimensional finite element model was created in this work to investigate the stresses distribution within rock-like samples with offset open non-persistent joints under biaxial loading. The results of this study have explained the fracture mechanisms observed in tests on rock-like material with open non-persistent offset joints [1]. Finite element code SAP2000 was used to study the stresses distribution within the specimens. Four-nodded isoperimetric plain strain element with two degree of freedom per node, and the three-nodded constant strain triangular element with two degree of freedom per node were used in the present study.The results of the present study explained the formation of wing cracks at the tip of the joints for low confining stress as well as the formation of wing cracks at the middle of the joint for the higher confining stress. High shear stresses found in the numerical study at the tip of the joints explained the formation of secondary cracks at the tip of the joints in the experimental study. The study results coincide with the experimental observations which showed that for bridge inclination of 0o, the coalescence occurred due to shear failure and for bridge inclination of 90o the coalescence occurred due to tensile failure while for the other bridge inclinations coalescence occurred due to mixed tensile and shear failure.
Abstract: Information regarding early onset neonatal sepsis
(EONS) pathogens may vary between regions. Global perspectives
showed Group B Streptococcal (GBS) as the most common causative
pathogens, but the widespread use of intrapartum antibiotics has
changed the pathogens pattern towards gram negative
microorganisms, especially E. coli. Objective of this study is to
describe the pathogens isolated, to assess current treatment and risk
of EONS. Records of 899 neonates born in three General Hospitals
between 2009 until 2012 were retrospectively reviewed. Proven was
found in 22 (3%) neonates. The majority was isolated with gram
positive organisms, 17 (2.3%). All grams positive and most gram
negative organisms showed sensitivity to the tested antibiotics. Only
two rare gram negative organisms showed total resistant. Male was
possible risk of proven EONS. Although proven EONS remains
uncommon in Malaysia, nonetheless, the effect of intrapartum
antibiotics still required continuous surveillance.
Abstract: This paper describes a complex energy signal model
that is isomorphic with digital human fingerprint images. By using
signal models, the problem of fingerprint matching is transformed
into the signal processing problem of finding a correlation between
two complex signals that differ by phase-rotation and time-scaling. A
technique for minutiae matching that is independent of image
translation, rotation and linear-scaling, and is resistant to missing
minutiae is proposed. The method was tested using random data
points. The results show that for matching prints the scaling and
rotation angles are closely estimated and a stronger match will have a
higher correlation.
Abstract: A mathematical model of the respiratory system is
introduced in this study. Geometrical dimensions of the respiratory
system were used to compute the acoustic properties of the
respiratory system using the electro-acoustic analogy. The effect of
the geometrical proportions of the respiratory system is observed in
the paper.
Abstract: We developed a non-contact method for the in-situ
monitoring of the thermal forming of glass and Si foils to optimize
the manufacture of mirrors for high-resolution space x-ray
telescopes. Their construction requires precise and light-weight
segmented optics with angular resolution better than 5 arcsec. We
used 75x25 mm Desag D263 glass foils 0.75 mm thick and 0.6 mm
thick Si foils. The glass foils were shaped by free slumping on a
frame at viscosities in the range of 109.3-1012 dPa·s, the Si foils by
forced slumping above 1000°C. Using a Nikon D80 digital camera,
we took snapshots of a foil-s shape every 5 min during its isothermal
heat treatment. The obtained results we can use for computer
simulations. By comparing the measured and simulated data, we can
more precisely define material properties of the foils and optimize
the forming technology.
Abstract: In this work, study the location of interface in a stirred vessel with Rushton impeller by computational fluid dynamic was presented. To modeling rotating the impeller, sliding mesh (SM) technique was used and standard k-ε model was selected for turbulence closure. Mean tangential, radial and axial velocities and also turbulent kinetic energy (k) and turbulent dissipation rate (ε) in various points of tank was investigated. Results show sensitivity of system to location of interface and radius of 7 to 10cm for interface in the vessel with existence characteristics cause to increase the accuracy of simulation.
Abstract: Automobile Industry has great importance in the
Spanish economy (8,7 % of the active Spanish population is
employed in this sector).The above mentioned sector has been one of
the principal sectors affected by the current economic crisis,
consistently, the budgets in advertising have been severely limited
(46,9 % less in the period of reference), these needs of reduction
have originated a substantial change in the advertising strategy (from
2007 the increase of the advertising investment in Internet is 251,6
%), and increase profitability. The growing use of social media by
consumers therefore makes online consumer conversations an
attractive additional format for Automobile firms to promote
products at a lower cost. This research analyzes the relation between
the activity in Social Media and the design in the car industry,
looking for relations between strategies of design based on Social
Media and sales and a channel of information for companies to know
what the consumer preferences. For this ongoing research we used a
longitudinal withdrawal of information has been used using
information of panel. Managerial and research implications of the
finding are discussed.
Abstract: The use of bioindicators plants (lichens, bryophytes
and Sphagnum....) in monitoring pollution by heavy metals has been
the subject of several works. However, few studies have addressed
the impact of specific type-s pollutants (fertilizers, pesticides.) on
these organisms.
We propose in this work to make the highlighting effect of NPKs
(NPK: nitrogen-phosphate-potassium-sulfate (NP2O5K2O) (15,15,15),
at concentrations of 10, 20, 30 , 40 and 50mM/L) on the activity of
detoxification enzymes (GSH/GST, CAT, APX and MDA) of plant
bioindicators (mosses and lichens) after treatment for 3 and 7 days.
This study shows the important role of the defense system in the
accumulation and tolerance to chemical pollutants through the
activation of enzymatic (GST (glutathione-S-transferase, APX
(ascorbat peroxidase), CAT (catalase)) and nonenzymatic biomarkers
(GSH (glutathione), MDA (malondialdehyde)) against oxidative
stress generated by the NPKs.
Abstract: Recently, lots of researchers are attracted to retrieving
multimedia database by using some impression words and their values.
Ikezoe-s research is one of the representatives and uses eight pairs of
opposite impression words. We had modified its retrieval interface and
proposed '2D-RIB'. In '2D-RIB', after a retrieval person selects a
single basic music, the system visually shows some other music
around the basic one along relative position. He/she can select one of
them fitting to his/her intention, as a retrieval result. The purpose of
this paper is to improve his/her satisfaction level to the retrieval result
in 2D-RIB. One of our extensions is to define and introduce the
following two measures: 'melody goodness' and 'general acceptance'.
We implement them in different five combinations. According to an
evaluation experiment, both of these two measures can contribute to
the improvement. Another extension is three types of customization.
We have implemented them and clarified which customization is
effective.
Abstract: In this work study the location of interface in a stirred vessel with a Concave impeller by computational fluid dynamic was presented. To modeling rotating the impeller, sliding mesh (SM) technique was used and standard k-ε model was selected for turbulence closure. Mean tangential, radial and axial velocities and also turbulent kinetic energy (k) and turbulent dissipation rate (ε) in various points of tank was investigated. Results show sensitivity of system to location of interface and radius of 7 to 10cm for interface in the vessel with existence characteristics cause to increase the accuracy of simulation.
Abstract: This article presents a current-mode quadrature
oscillator using differential different current conveyor (DDCC) and
voltage differencing transconductance amplifier (VDTA) as active
elements. The proposed circuit is realized fro m a non-inverting
lossless integrator and an inverting second order low-pass filter. The
oscillation condition and oscillation frequency can be
electronically/orthogonally controlled via input bias currents. The
circuit description is very simple, consisting of merely 1 DDCC, 1
VDTA, 1 grounded resistor and 3 grounded capacitors. Using only
grounded elements, the proposed circuit is then suitable for IC
architecture. The proposed oscillator has high output impedance
which is easy to cascade or dive the external load without the buffer
devices. The PSPICE simulation results are depicted, and the given
results agree well with the theoretical anticipation. The power
consumption is approximately 1.76mW at ±1.25V supply voltages.
Abstract: Border Gateway Protocol (BGP) is the standard routing protocol between various autonomous systems (AS) in the internet. In the event of failure, a considerable delay in the BGP convergence has been shown by empirical measurements. During the convergence time the BGP will repeatedly advertise new routes to some destination and withdraw old ones until it reach a stable state. It has been found that the KEEPALIVE message timer and the HOLD time are tow parameters affecting the convergence speed. This paper aims to find the optimum value for the KEEPALIVE timer and the HOLD time that maximally reduces the convergence time without increasing the traffic. The KEEPALIVE message timer optimal value founded by this paper is 30 second instead of 60 seconds, and the optimal value for the HOLD time is 90 seconds instead of 180 seconds.
Abstract: Since injection engines have a considerable portion, in
consumption of energy and environmental pollution, using an
alternative source of energy with lower pollutant effects in this
regard is necessary.
Biodiesel fuel is a suitable alternative for gasoline in diesel
engines.
In this research the property of biodiesel, the function and the
pollution effects of diesel engine, when using 100% biodiesel, using
100% gasoline and mixing ratio of both fuels for comparing them,
have been investigated.
The researches have shown, using biodiesel fuel in prevalent
diesel engine, will reduce the pollutants such as Co, half burned
carbohydrate and suspended particles and a little increase in
oxidation will achieve while power consumption, particularly fuel
and thermal efficiency of diesel fuel has the same.
Abstract: Short Message Service (SMS) has grown in
popularity over the years and it has become a common way of
communication, it is a service provided through General System
for Mobile Communications (GSM) that allows users to send text
messages to others.
SMS is usually used to transport unclassified information, but
with the rise of mobile commerce it has become a popular tool for
transmitting sensitive information between the business and its
clients. By default SMS does not guarantee confidentiality and
integrity to the message content.
In the mobile communication systems, security (encryption)
offered by the network operator only applies on the wireless link.
Data delivered through the mobile core network may not be
protected. Existing end-to-end security mechanisms are provided
at application level and typically based on public key
cryptosystem.
The main concern in a public-key setting is the authenticity of
the public key; this issue can be resolved by identity-based (IDbased)
cryptography where the public key of a user can be derived
from public information that uniquely identifies the user.
This paper presents an encryption mechanism based on the IDbased
scheme using Elliptic curves to provide end-to-end security
for SMS. This mechanism has been implemented over the standard
SMS network architecture and the encryption overhead has been
estimated and compared with RSA scheme. This study indicates
that the ID-based mechanism has advantages over the RSA
mechanism in key distribution and scalability of increasing
security level for mobile service.