Abstract: The effect of particle size on shear strength of
granular materials are investigated using direct shear tests. Small
direct shear test (60 mm by 60 mm by 24 mm deep) were conducted
for particles passing the sieves with opening size of 2.36 mm.
Meanwhile, particles passing the standard 20 mm sieves were tested
using large direct shear test (300 mm by 300 mm by 200 mm deep).
The large direct shear tests and the small direct shear tests carried out
using the same shearing rate of 0.09 mm/min and similar normal
stresses of 100, 200 and 300 kPa. The results show that the peak and
residual shear strength increases as particle size increases.
Abstract: This paper focuses on the presentation of results
which were obtained as a part of the project FR-TI 3/742: “System of
Lightweight Materials for Finishing of Buildings with Waste Raw
Materials”. Attention was paid to the light weighting of polymermodified
mortars applicable as adhesives, screeds and repair mortars.
In terms of repair mortars, they were ones intended for the sanitation
of aerated concrete.
Abstract: The objective of the study was to select the survival of
probiotic strains when exposed to acidic and bile salts condition. Four
probiotic strains Lactobacillus casei subsp. rhamnosus TISTR 047,
Lactobacillus casei TISTR 1500, Lactobacillus acidophilus TISTR
1338 and Lactobacillus plantarum TISTR 1465 were cultured in
MRS broth and incubated at 35ºC for 15 hours before being inoculated
into acidic condition 5 M HCl, pH 2 for 2 hours and bile salt 0.3%,
pH 5.8 for 8 hour. The survived probiotics were counted in MRS agar.
Among four stains, Lactobacillus casei subsp. rhamnosus TISTR 047
was the highest tolerance specie. Lactobacillus casei subsp.
rhamnosus TISTR 047 reduced 6.74±0.07 log CFU/ml after growing
in acid and 5.52±0.05 log CFU/ml after growing in bile salt. Then,
double emulsion of microorganisms was chosen to encapsulate before
spray drying. Spray drying was done with the inlet temperature 170ºC
and outlet temperature 80ºC. The results showed that the survival of
encapsulated Lactobacillus casei subsp. rhamnosus TISTR 047 after
spray drying decreased from 9.63 ± 0.32 to 8.31 ± 0.11 log CFU/ml
comparing with non-encapsulated, 9.63 ± 0.32 to 4.06 ± 0.08 log
CFU/ml. Therefore, Lactobacillus casei subsp. rhamnosus TISTR 047
would be able to survive in gastrointestinal and spray drying condition.
Abstract: Persea declinata (Bl.) Kosterm is a member of the
Lauraceae family, widely distributed in Southeast Asia. It is from the
same genus with avocado (Persea americana Mill), which is widely
consumed as food and for medicinal purposes. In the present study,
we examined the anticancer properties of Persea declinata (Bl.)
Kosterm bark methanolic crude extract (PDM). PDM exhibited a
potent antiproliferative effect in MCF-7 human breast cancer cells,
with an IC50 value of 16.68 .g/mL after 48h of treatment. We
observed that PDM caused cell cycle arrest and subsequent apoptosis
in MCF-7 cells, as exhibited by increased population at G0/G1 phase,
higher lactate dehydrogenase (LDH) release, and DNA
fragmentation. Mechanistic studies showed that PDM caused
significant elevation in ROS production, leading to perturbation of
mitochondrial membrane potential, cell permeability, and activation
of caspases-3/7. On the other hand, real-time PCR and Western blot
analysis showed that PDM treatment increased the expression of the
proapoptotic molecule, Bax, but decreased the expression of
prosurvival proteins, Bcl-2 and Bcl-xL, in a dose-dependent manner.
These findings imply that PDM could inhibit proliferation in MCF-7
cells via cell cycle arrest and apoptosis induction, indicating its
potential as a therapeutic agent worthy of further development.
Abstract: This article presents summary on preparation and
characterization of zinc, copper, cadmium and cobalt chromite
nanocrystals, embedded in an amorphous silica matrix. The
ZnCr2O4/SiO2, CuCr2O4/SiO2, CdCr2O4/SiO2 and CoCr2O4/SiO2
nanocomposites were prepared by a conventional sol-gel method
under acid catalysis. Final heat treatment of the samples was carried
out at temperatures in the range of 900−1200 ◦C to adjust the
phase composition and the crystallite size, respectively. The resulting
samples were characterized by Powder X-ray diffraction (PXRD),
High Resolution Transmission Electron Microscopy (HRTEM),
Raman/FTIR spectroscopy and magnetic measurements. Formation
of the spinel phase was confirmed in all samples. The average size of
the nanocrystals was determined from the PXRD data and by direct
particle size observation on HRTEM; both results were correlated.
The mean particle size (reviewed by HRTEM) was in the range from
∼4 to 46 nm. The results showed that the sol-gel method can be
effectively used for preparation of the spinel chromite nanoparticles
embedded in the silica matrix and the particle size is driven by the
type of the cation A2+ in the spinel structure and the temperature
of the final heat treatment. Magnetic properties of the nanocrystals
were found to be just moderately modified in comparison to the bulk
phases.
Abstract: The organizations of European and Czech critical
infrastructure have specific position, mission, characteristics and
behaviour in European Union and Czech state/business environments,
regarding specific requirements for regional and global security
environments. They must respect policy of national security and
global rules, requirements and standards in all their inherent and
outer processes of supply - customer chains and networks. A
controlling is generalized capability to have control over situational
policy. This paper aims and purposes are to introduce the controlling
as quite new necessary process attribute providing for critical
infrastructure is environment the capability and profit to achieve its
commitment regarding to the effectiveness of the quality
management system in meeting customer/ user requirements and also
the continual improvement of critical infrastructure organization’s
processes overall performance and efficiency, as well as its societal
security via continual planning improvement via DYVELOP
modelling.
Abstract: This paper attempts to evaluate the effect of fire
damage on concrete by using nonlinear resonance vibration method,
one of the nonlinear nondestructive method. Concrete exhibits not
only nonlinear stress-strain relation but also hysteresis and discrete
memory effect which are contained in consolidated materials.
Hysteretic materials typically show the linear resonance frequency
shift. Also, the shift of resonance frequency is changed according to
the degree of micro damage. The degree of the shift can be obtained
through nonlinear resonance vibration method. Five exposure
scenarios were considered in order to make different internal micro
damage. Also, the effect of post-fire-curing on fire-damaged concrete
was taken into account to conform the change in internal damage.
Hysteretic nonlinearity parameter was obtained by amplitudedependent
resonance frequency shift after specific curing periods. In
addition, splitting tensile strength was measured on each sample to
characterize the variation of residual strength. Then, a correlation
between the hysteretic nonlinearity parameter and residual strength
was proposed from each test result.
Abstract: Diabetes is a growing health problem in worldwide.
Especially, the patients with Type 1 diabetes need strict glycemic
control because they have deficiency of insulin production. This
paper attempts to control blood glucose based on body mathematical
body model. The Bergman minimal mathematical model is used to
develop the nonlinear controller. A novel back-stepping based sliding
mode control (B-SMC) strategy is proposed as a solution that
guarantees practical tracking of a desired glucose concentration. In
order to show the performance of the proposed design, it is compared
with conventional linear and fuzzy controllers which have been done
in previous researches. The numerical simulation result shows the
advantages of sliding mode back stepping controller design to linear
and fuzzy controllers.
Abstract: Nonalcoholic fatty liver disease (NAFLD) has
increased in conjunction with obesity. The accuracy of risk factors
for detecting NAFLD in obese adolescents has not undergone a
formal evaluation. The aim of this study was to evaluate predictors of
NAFLD among Egyptian female obese adolescents. The study
included 162 obese female adolescents. All were subjected to
anthropometry, biochemical analysis and abdominal ultrasongraphic
assessment. Metabolic syndrome (MS) was diagnosed according to
the IDF criteria. Significant association between presence of MS and
NAFLD was observed. Obese adolescents with NAFLD had
significantly higher levels of ALT, triglycerides, fasting glucose,
insulin, blood pressure and HOMA-IR, whereas decreased HDL-C
levels as compared with obese cases without NAFLD. Receiver–
operating characteristic (ROC) curve analysis shows that ALT is a
sensitive predictor for NAFLD, confirming that ALT can be used as a
marker of NAFLD.
Abstract: The aim of the paper was to elaborate a novel calculator BasWilCalc, that allows to estimate the actual amount of biomass on the basket willow plantations. The proposed method is based on the results of field experiment conducted during years 2011-2013 on basket willow plantation in the south-western part of Poland. As input data the results of destructive measurements of the diameter, length and weight of willow stems and non-destructive biometric measurements of diameter in the middle of stems and their length during the growing season performed at weekly intervals were used. Performed analysis enabled to develop the algorithm which, due to the fact that energy plantations are of known and constant planting structure, allows to estimate the actual amount of willow basket biomass on the plantation with a given probability and accuracy specified by the model, based on the number of stems measured and the age of the plantation.
Abstract: The mathematical analysis on radiation obtained and
the development of the solar photovoltaic (PV) array groundwater
pumping is needed in the rural areas of Thohoyandou for sizing and
power performance subject to the climate conditions within the area.
A simple methodology approach is developed for the directed
coupled solar, controller and submersible ground water pump system.
The system consists of a PV array, pump controller and submerged
pump, battery backup and charger controller. For this reason, the
theoretical solar radiation is obtained for optimal predictions and
system performance in order to achieve different design and
operating parameters. Here the examination of the PV schematic
module in a Direct Current (DC) application is used for obtainable
maximum solar power energy for water pumping. In this paper, a
simple efficient photovoltaic water pumping system is presented with
its theoretical studies and mathematical modeling of photovoltaics
(PV) system.
Abstract: This paper presents a comparison of reference
management software between RefWorks and Zotero. The results
were drawn by comparing two software and the novelty of this paper
is the comparative analysis of software and it has shown that
ReftWorks can import more information from the Google Scholar for
the researchers. This finding could help to know researchers to use
the reference management software.
Abstract: Calcium phosphate coating (CaP) has been employed
for protein delivery, but the typical direct protein adsorption on the
coating led to low incorporation content and fast release of the
protein from the coating. By using bovine serum albumin (BSA) as a
model protein, rapid biomimetic co-precipitation between calcium
phosphate and BSA was employed to control the distribution of BSA
within calcium phosphate coating during biomimetic formation on
titanium surface for only 6 h at 50oC in an accelerated calcium
phosphate solution. As a result, the amount of BSA incorporation and
release duration could be increased by using a rapid biomimetic coprecipitation
technique. Up to 43 fold increases in the BSA
incorporation content and the increase from 6 h to more than 360 h in
release duration compared to typical direct adsorption technique were
observed depending on the initial BSA concentration used during coprecipitation
(1, 10 and 100 μg.ml-1). From x-ray diffraction and
Fourier transform infrared spectroscopy studies, the coating
composition was not altered with the incorporation of BSA by this
rapid biomimetic co-precipitation and mainly comprised octacalcium
phosphate and hydroxyapatite. However, the microstructure of
calcium phosphate crystals changed from straight, plate-like units to
curved, plate-like units with increasing BSA content.
Abstract: In Capitalism all economic activity rests upon a set of
core institutional foundations, main from which are privately owned
capital assets and profit. How these core institutional foundations are
working in former soviet countries, in particular in Travel and
Tourism Industry of Georgia?
The role of Travel and Tourism as a key pillar of economic growth
is being increasingly recognized by governments in all regions of the
world. For the last few years Georgia succeeded in the World Bank
and IFC “Doing Business” rankings. Despite of that, during decades
totally different statistical data of the tourism sector were provided by
the different State bodies; economic parameters were published few,
or not published at all.
The frequency and extent of property rights violation in Georgia
has repeatedly been the subject of concern for the last decade. Total
value of abrogated by the former Georgian Government private
property is estimated approximately in US$4-5 billion.
Thus, if economic profitability is unknown and property rights are
not protected – that means that the main institutional foundations of
capitalism in Georgia, are not working properly yet, that cause
management problems at all levels of the national Travel and
Tourism industry of Georgia.
Abstract: The purpose of this research is to study of consumer
perception and understanding consumer buying behavior that related
between satisfied and factors affecting the purchasing. Methodology
can be classified between qualitative and quantitative approaches for
the qualitative research were interviews from middlemen who bought
organic vegetables, and middlemen related to production and
marketing system. A questionnaire was utilized as a tool to collect
data. Statistics utilized in this research included frequency,
percentage, mean, standard deviation, and multiple regression
analysis. The result show the reason to decision buying motives is
Fresh products of organic vegetables is the most significant factor on
individuals’ income, with a b of –.143, t = –2.470, the price of
organic vegetables is the most significant factor on individuals’
income, with a b of .176, t = 2.561, p value = .011. The results show
that most people with higher income think about the organic products
are expensive and have negative attitudes towards organic vegetable
as individuals with low and medium income level. Therefore,
household income had a significant influence on the purchasing
decision.
Abstract: The purpose of this research was to identify factors
that influenced the success of e-commerce implementation within
SMEs businesses. In order to achieve the objectives of this research,
the researcher collected data from random firms in Thailand, both the
users and those who are not using the e-commerce. The data was
comprised of the results of 310 questionnaires, as well as 10
interviews with owner/managers of businesses who are currently
using e-commerce successfully. The data were analyzed by using
descriptive statistics, which included frequency, percentages, mean,
and the standard deviation of pertinent factors. Independent t-test and
one-way ANOVA test were also used. The findings of this research
revealed that 50% of all the firms surveyed had e-commerce website,
whereas, over 20% of all firms surveyed had developing an ecommerce
strategy. The result findings also indicate that
organizational factors, technological factors and environment factors
as significant factors effecting success of e-commerce
implementation in SMEs. From the hypotheses testing, the findings
revealed that the different level of support use ecommerce by
owner/manager had different success in e-commerce implementation.
Moreover, the difference in e-commerce management approach
affected the success in terms of higher total sales for the business or
higher number of retained or returning customers.
Abstract: The success of any retail business is predisposed by its
swift response and its knack in understanding the constraints and the
requirements of customers. In this paper a conceptual design model
of an automated customer-friendly supermarket has been proposed.
In this model a 10-sided, space benefited, regular polygon shaped
gravity shelves have been designed for goods storage and effective
customer-specific algorithms have been built-in for quick automatic
delivery of the randomly listed goods. The algorithm is developed
with two main objectives, viz., delivery time and priority. For
meeting these objectives the randomly listed items are reorganized
according to the critical-path of the robotic arm specific to the
identified shop and its layout and the items are categorized according
to the demand, shape, size, similarity and nature of the product for an
efficient pick-up, packing and delivery process. We conjectured that
the proposed automated supermarket model reduces business
operating costs with much customer satisfaction warranting a winwin
situation.
Abstract: Copper being one of the major intrinsic residual
impurities in steel possesses the tendency to induce severe
microstructural distortions if not controlled within certain limits.
Hence, this paper investigates the effect of this element on the
mechanical properties of construction steel with a view to ascertain
its safe limits for effective control. The experiment entails collection
of statistically scheduled samples of hot rolled profiles with varied
copper concentrations in the range of 0.12-0.39 wt. %. From these
samples were prepared standard test specimens subjected to tensile,
impact, hardness and microstructural analyses. Results show a rather
huge compromise in mechanical properties as the specimens
demonstrated 54.3%, 74.2% and 64.9% reduction in tensile strength,
impact energy and hardness respectively as copper content increases
from 0.12 wt. % to 0.39 wt. %. The steel’s abysmal performance is
due to the severe distortion of the microstructure occasioned by the
development of incoherent complex compounds which weaken the
pearlite reinforcing phase. It is concluded that the presence of copper
above 0.22 wt. % is deleterious to construction steel performance.
Abstract: The discarded clam shell waste, fossil and edible oil
as biolubricant feedstocks create environmental impacts and food
chain dilemma, thus this work aims to circumvent these issues by
using activated saltwater clam shell waste (SCSW) as solid catalyst
for conversion of Jatropha curcas oil as non-edible sources to ester
biolubricant. The characterization of solid catalyst was done by
Differential Thermal Analysis-Thermo Gravimetric Analysis (DTATGA),
X-Ray Fluorescence (XRF), X-Ray Diffraction (XRD),
Brunauer-Emmett-Teller (BET), Field Emission Scanning Electron
Microscopy (FESEM) and Fourier Transformed Infrared
Spectroscopy (FTIR) analysis. The calcined catalyst was used in the
transesterification of Jatropha oil to methyl ester as the first step, and
the second stage was involved the reaction of Jatropha methyl ester
(JME) with trimethylolpropane (TMP) based on the various process
parameters. The formated biolubricant was analyzed using the
capillary column (DB-5HT) equipped Gas Chromatography (GC).
The conversion results of Jatropha oil to ester biolubricant can be
found nearly 96.66%, and the maximum distribution composition
mainly contains 72.3% of triester (TE).
Abstract: Economic Dispatch (ED) is one of the most
challenging problems of power system since it is difficult to determine
the optimum generation scheduling to meet the particular load demand
with the minimum fuel costs while all constraints are satisfied. The
objective of the Economic Dispatch Problems (EDPs) of electric
power generation is to schedule the committed generating units
outputs so as to meet the required load demand at minimum operating
cost while satisfying all units and system equality and inequality
constraints. In this paper, an efficient and practical steady-state genetic
algorithm (SSGAs) has been proposed for solving the economic
dispatch problem. The objective is to minimize the total generation
fuel cost and keep the power flows within the security limits. To
achieve that, the present work is developed to determine the optimal
location and size of capacitors in transmission power system where,
the Participation Factor Algorithm and the Steady State Genetic
Algorithm are proposed to select the best locations for the capacitors
and determine the optimal size for them.