Abstract: ZnO nanostructures including nanowires, nanorods,
and nanoneedles were successfully deposited on GaAs substrates,
respectively, by simple two-step chemical method for the first time. A
ZnO seed layer was firstly pre-coated on the O2-plasma treated
substrate by sol-gel process, followed by the nucleation of ZnO
nanostructures through hydrothermal synthesis. Nanostructures with
different average diameter (15-250 nm), length (0.9-1.8 μm), density
(0.9-16×109 cm-2) were obtained via adjusting the growth time and
concentration of precursors. From the reflectivity spectra, we
concluded ordered and taper nanostructures were preferential for
photovoltaic applications. ZnO nanoneedles with an average diameter
of 106 nm, a moderate length of 2.4 μm, and the density of 7.2×109
cm-2 could be synthesized in the concentration of 0.04 M for 18 h.
Integrated with the nanoneedle array, the power conversion efficiency
of single junction solar cell was increased from 7.3 to 12.2%,
corresponding to a 67% improvement.
Abstract: Nanocrystalline thin film of Na0.1V2O5.nH2O xerogel
obtained by sol gel synthesis was used as gas sensor. Gas sensing
properties of different gases such as hydrogen, petroleum and
humidity were investigated. Applying XRD and TEM the size of the
nanocrystals is found to be 7.5 nm. SEM shows a highly porous
structure with submicron meter-sized voids present throughout the
sample. FTIR measurement shows different chemical groups
identifying the obtained series of gels. The sample was n-type
semiconductor according to the thermoelectric power and electrical
conductivity. It can be seen that the sensor response curves from
130oC to 150oC show a rapid increase in sensitivity for all types of
gas injection, low response values for heating period and the rapid
high response values for cooling period. This result may suggest that
this material is able to act as gas sensor during the heating and
cooling process.
Abstract: This paper describes the development of a 16-ports optical code division multiple access (OCDMA) encoder prototype based on Arrayed Waveguide Grating (AWG) and optical switches. It is potentially to provide a high security for data transmission due to all data will be transmitted in binary code form. The output signals from AWG are coded with a binary code that given to an optical switch before it signal modulate with the carrier and transmitted to the receiver. The 16-ports encoder used 16 double pole double throw (DPDT) toggle switches to control the polarization of voltage source from +5 V to -5 V for 16 optical switches. When +5 V is given, the optical switch will give code '1' and vice versa. The experimental results showed the insertion loss, crosstalk, uniformity, and optical signal-noise-ratio (OSNR) for the developed prototype are
Abstract: Artificial Bee Colony (ABC) algorithm is a relatively new swarm intelligence technique for clustering. It produces higher
quality clusters compared to other population-based algorithms but with poor energy efficiency, cluster quality consistency and typically slower in convergence speed. Inspired by energy saving foraging behavior of natural honey bees this paper presents a Quality and Quantity Aware Artificial Bee Colony (Q2ABC) algorithm to improve quality of cluster identification, energy efficiency and convergence speed of the original ABC. To evaluate the performance of Q2ABC algorithm, experiments were conducted on a suite of ten benchmark UCI datasets. The results demonstrate Q2ABC outperformed ABC and K-means algorithm in the quality of clusters delivered.
Abstract: Robustness is one of the primary performance criteria for an Intelligent Video Surveillance (IVS) system. One of the key factors in enhancing the robustness of dynamic video analysis is,providing accurate and reliable means for shadow detection. If left undetected, shadow pixels may result in incorrect object tracking and classification, as it tends to distort localization and measurement information. Most of the algorithms proposed in literature are computationally expensive; some to the extent of equalling computational requirement of motion detection. In this paper, the homogeneity property of shadows is explored in a novel way for shadow detection. An adaptive division image (which highlights homogeneity property of shadows) analysis followed by a relatively simpler projection histogram analysis for penumbra suppression is the key novelty in our approach.
Abstract: The objective of the present work is to conduct
investigations leading to a more complete explanation of single phase
natural convective heat transfer in an enclosure with fin utilizing
nano fluids. The nano fluid used, which is composed of Aluminum
oxide nano particles in suspension of Ethylene glycol, is provided at
various volume fractions. The study is carried out numerically for a
range of Rayleigh numbers, fin heights and aspect ratio. The flow and
temperature distributions are taken to be two-dimensional. Regions
with the same velocity and temperature distributions are identified as
symmetry of sections. One half of such a rectangular region is chosen
as the computational domain taking into account the symmetry about
the fin. Transport equations are modeled by a stream functionvorticity
formulation and are solved numerically by finite-difference
schemes. Comparisons with previously published works on the basis
of special cases are done. Results are presented in the form of
streamline, vector and isotherm plots as well as the variation of local
Nusselt number along the fin under different conditions.
Abstract: Indigenous Knowledge (IK) has many social and
economic benefits. However, IK is at the risk of extinction due to the
difficulties to preserve it as most of the IK largely remains
undocumented. This study aims to design a model of the factors
affecting the adoption of Information and Communication
Technologies (ICTs) for the preservation of IK. The proposed model
is based on theoretical frameworks on ICT adoption. It was designed
following a literature review of ICT adoption theories for households,
and of the factors affecting ICT adoption for IK. The theory that
fitted to the best all factors was then chosen as the basis for the
proposed model. This study found that the Model of Adoption of
Technology in Households (MATH) is the most suitable theoretical
framework for modeling ICT adoption factors for the preservation of
IK.
Abstract: This paper presents an improvement method of
the multiple pitch estimation algorithm using comb filters.
Conventionally the pitch was estimated by using parallel
-connected comb filters method (PCF). However, PCF has
problems which often fail in the pitch estimation when there is
the fundamental frequency of higher tone near harmonics of
lower tone. Therefore the estimation is assigned to a wrong
note when shared frequencies happen. This issue often occurs
in estimating octave 3 or more. Proposed method, for solving
the problem, estimates the pitch with every harmonic instead of
every octave. As a result, our method reaches the accuracy of
more than 80%.
Abstract: The objective of this research seeks to transmit a distance training model to the community in the upper northeastern region. The group sampling consists of 60 community leaders in the municipality of sub-district Kumphawapi, Kumphawapi Disrict, Udonthani Province. The research tools rely on the following instruments, they are : 1) the achievement test of community leaders- training and 2) the satisfaction questionnaires of community leaders. The statistics used in data analysis takes the statistical mean, percentage, standard deviation, and statistical T-test. The resulted findings reveal : 1) the efficiency of the distance training developed by the researcher for the community leaders joining in the training received the average score between in-training and post-training period higher than the setup criterion, 2) the two groups of participants in the training achieved higher knowledge than their pre-training state, 3) the comparison of the achievements between the two group presented no different results, 4) the community leaders obtained the high-to-highest satisfaction.
Abstract: The objectives of this study are to determine the
effects of soil cover type on characteristics of leachates generated
from landfill lysimeters. Four lysimeters with diameter and height
of 0.15 and 3.00 m, respectively, were prepared. Three lysimeters
were filled with municipal waste and three different cover soil types
i.e. sandy loam soil, silty loam soil and clay soil while another
lysimeter was filled solely with municipal waste. The study was
conducted in the rainy season. Leachate quantities were measured
every day and leachate characteristics were determined once a week.
The cumulative leachate quantity from the lysimeter filled solely
with municipal waste was found to be around 27% higher than the
lysimeters using cover soils. There were no any differences of the
cumulative leachate amounts generated from the lysimeters using
three types of soils. The comparison of the total mass of pollutants
generated from all lysimeters showed that the lysimeter filled solely
with municipal waste generated the maximum quantities of
pollutants. Among the lysimeters using different types of soils, the
lysimeter using sandy loam soil generated the lowest amount of most
of pollutants, compared with the lysimeters using silty loam and clay
soils. It can be concluded that in term of pollutant attenuation in the
leachate, a sandy loam is the most suitable soil to be used as a cover
soil in the landfill.
Abstract: This contribution deals with the relationship between
communication effectiveness and the extent of communication
among organizational units. To facilitate communication between
employees and to increase the level of understanding, the knowledge
of communication tools is necessary. Recent experience has shown
that personal communication is critical for smooth running of
companies and cannot be fully replaced by any form of technical
communication devices.
Below are presented the outcomes of the research on the
relationship between the extent of communication among
organisational units and its efficiency.
Abstract: To support user mobility for a wireless network new mechanisms are needed and are fundamental, such as paging, location updating, routing, and handover. Also an important key feature is mobile QoS offered by the WATM. Several ATM network protocols should be updated to implement mobility management and to maintain the already ATM QoS over wireless ATM networks. A survey of the various schemes and types of handover is provided. Handover procedure allows guarantee the terminal connection reestablishment when it moves between areas covered by different base stations. It is useful to satisfy user radio link transfer without interrupting a connection. However, failure to offer efficient solutions will result in handover important packet loss, severe delays and degradation of QoS offered to the applications. This paper reviews the requirements, characteristics and open issues of wireless ATM, particularly with regard to handover. It introduces key aspects of WATM and mobility extensions, which are added in the fixed ATM network. We propose a flexible approach for handover management that will minimize the QoS deterioration. Functional entities of this flexible approach are discussed in order to achieve minimum impact on the connection quality when a MT crosses the BS.
Abstract: A Variable Structure Model Reference Adaptive Controller using state variables is proposed for a class of multi input-multi output systems. Adaptation law is of variable structure type and switching functions is designed based on stability requirements. Global exponential stability is proved based on Lyapunov criterion. Transient behavior is analyzed using sliding mode control and shows perfect model following at a finite time.
Abstract: This paper describes the design of a voltage based maximum power point tracker (MPPT) for photovoltaic (PV) applications. Of the various MPPT methods, the voltage based method is considered to be the simplest and cost effective. The major disadvantage of this method is that the PV array is disconnected from the load for the sampling of its open circuit voltage, which inevitably results in power loss. Another disadvantage, in case of rapid irradiance variation, is that if the duration between two successive samplings, called the sampling period, is too long there is a considerable loss. This is because the output voltage of the PV array follows the unchanged reference during one sampling period. Once a maximum power point (MPP) is tracked and a change in irradiation occurs between two successive samplings, then the new MPP is not tracked until the next sampling of the PV array voltage. This paper proposes an MPPT circuit in which the sampling interval of the PV array voltage, and the sampling period have been shortened. The sample and hold circuit has also been simplified. The proposed circuit does not utilize a microcontroller or a digital signal processor and is thus suitable for low cost and low power applications.
Abstract: Polymer melt compressibility and mold surface roughness, which are generally ignored during the filling stage of the conventional injection molding, may become increasingly significant in micro injection molding where the parts become smaller. By employing the 2.5D generalized Hele-Shaw model, we presented here the effects of polymer compressibility and mold surface roughness on mold-filling in a micro-thickness cavity. To elucidate the effects of surface roughness, numerical investigations were conducted using a cavity flat plate which has two halves with different surface roughness. This allows the comparison of flow field on two different halves under identical processing conditions but with different roughness. Results show that polymer compressibility and mold surface roughness have effects on mold filling in micro injection molding. There is in shrinkage reduction as the density is increased due to polymer melt compressibility during the filling stage.
Abstract: QoS Routing aims to find paths between senders and
receivers satisfying the QoS requirements of the application which
efficiently using the network resources and underlying routing
algorithm to be able to find low-cost paths that satisfy given QoS
constraints. The problem of finding least-cost routing is known to be
NP hard or complete and some algorithms have been proposed to
find a near optimal solution. But these heuristics or algorithms either
impose relationships among the link metrics to reduce the complexity
of the problem which may limit the general applicability of the
heuristic, or are too costly in terms of execution time to be applicable
to large networks. In this paper, we analyzed two algorithms namely
Characterized Delay Constrained Routing (CDCR) and Optimized
Delay Constrained Routing (ODCR). The CDCR algorithm dealt an
approach for delay constrained routing that captures the trade-off
between cost minimization and risk level regarding the delay
constraint. The ODCR which uses an adaptive path weight function
together with an additional constraint imposed on the path cost, to
restrict search space and hence ODCR finds near optimal solution in
much quicker time.
Abstract: Small signal stability causes small perturbations in the
generator that can cause instability in the power network. It is
generally known that small signal stability are directly related to the
generator and load properties. This paper examines the effects of
generator input variations on power system oscillations for a small
signal stability study. Eigenvaules and eigenvectors are used to
examine the stability of the power system. The dynamic power
system's mathematical model is constructed and thus calculated using
load flow and small signal stability toolbox on MATLAB. The power
system model is based on a 3-machine 9-bus system that was
modified to suit this study. In this paper, Participation Factors are a
means to gauge the effects of variation in generation with other
parameters on the network are also incorporated.
Abstract: The mixing behaviors of dry and wet granular
materials in gas fluidized bed systems were investigated
computationally using the combined Computational Fluid Dynamics
and Discrete Element Method (CFD-DEM). Dry particles were
observed to mix fairly rapidly during the fluidization process due to
vigorous relative motions between particles induced by the flow of
gas. In contrast, due to the presence of strong cohesive forces arising
from capillary liquid bridges between wet particles, the mixing
efficiencies of wet granular materials under similar operating
conditions were observed to be reduced significantly.
Abstract: In this paper we present a novel design of a wearable
electronic textile. After defining a special application, we used the
specifications of some low power, tiny elements including sensors,
microcontrollers, transceivers, and a fault tolerant special topology to
have the most reliability as well as low power consumption and
longer lifetime. We have considered two different conditions as
normal and bodily critical conditions and set priorities for using
different sensors in various conditions to have a longer effective
lifetime.
Abstract: Ground-level tropospheric ozone is one of the air
pollutants of most concern. It is mainly produced by photochemical
processes involving nitrogen oxides and volatile organic compounds
in the lower parts of the atmosphere. Ozone levels become
particularly high in regions close to high ozone precursor emissions
and during summer, when stagnant meteorological conditions with
high insolation and high temperatures are common.
In this work, some results of a study about urban ozone
distribution patterns in the city of Badajoz, which is the largest and
most industrialized city in Extremadura region (southwest Spain) are
shown. Fourteen sampling campaigns, at least one per month, were
carried out to measure ambient air ozone concentrations, during
periods that were selected according to favourable conditions to
ozone production, using an automatic portable analyzer.
Later, to evaluate the ozone distribution at the city, the measured
ozone data were analyzed using geostatistical techniques. Thus, first,
during the exploratory analysis of data, it was revealed that they were
distributed normally, which is a desirable property for the subsequent
stages of the geostatistical study. Secondly, during the structural
analysis of data, theoretical spherical models provided the best fit for
all monthly experimental variograms. The parameters of these
variograms (sill, range and nugget) revealed that the maximum
distance of spatial dependence is between 302-790 m and the
variable, air ozone concentration, is not evenly distributed in reduced
distances. Finally, predictive ozone maps were derived for all points
of the experimental study area, by use of geostatistical algorithms
(kriging). High prediction accuracy was obtained in all cases as
cross-validation showed. Useful information for hazard assessment
was also provided when probability maps, based on kriging
interpolation and kriging standard deviation, were produced.