Abstract: This work is an attempt to use the standard Smoothed
Particle Hydrodynamics methodology for the simulation of the
complex unsteady, free-surface flow in a rotating Turgo impulse
water turbine. A comparison of two different geometries was
conducted. The SPH method due to its mesh-less nature is capable of
capturing the flow features appearing in the turbine, without
diffusion at the water/air interface. Furthermore results are compared
with a commercial CFD package (Fluent®) and the SPH algorithm
proves to be capable of providing similar results, in much less time
than the mesh based CFD program. A parametric study was also
performed regarding the turbine inlet angle.
Abstract: The thermal, epithermal and fast fluxes were
calculated for three irradiation channels at Egypt Second Research
Reactor (ETRR-2) using CITVAP code. The validity of the
calculations was verified by experimental measurements. There are
some deviations between measurements and calculations. This is due
to approximations in the calculation models used, homogenization of
regions, condensation of energy groups and uncertainty in nuclear
data used. Neutron flux data for the three irradiation channels are
now available. This would enable predicting the irradiation
conditions needed for future radioisotope production.
Abstract: Several studies have shown the association between
ambient particulate matter (PM) and adverse health effects and
climate change, thus highlighting the need to limit the anthropogenic
sources of PM. PM Exposure is commonly monitored as mass
concentration of PM10 (particle aerodynamic diameter < 10μm) or
PM2.5 (particle aerodynamic diameter < 2.5μm), although increasing
toxicity with decreasing aerodynamic diameter has been reported due
to increased surface area and enhanced chemical reactivity with other
species. Additionally, the light scattering properties of PM increases
with decreasing size. Hence, it is important to study the chemical
characterization of finer fraction of the particulate matter and to
identify their sources so that they can be controlled appropriately to a
large extent at the sources before reaching to the receptors.
Abstract: The power consumption of an Optical Packet Switch
equipped with SOA technology based Spanke switching fabric is
evaluated. Sophisticated analytical models are introduced to evaluate
the power consumption versus the offered traffic, the main
switch parameters, and the used device characteristics. The impact
of Amplifier Spontaneous Emission (ASE) noise generated by a
transmission system on the power consumption is investigated. As
a matter of example for 32×32 switches supporting 64 wavelengths
and offered traffic equal to 0,8, the average energy consumption per
bit is 5, 07 · 10-2 nJ/bit and increases if ASE noise introduced by
the transmission systems is increased.
Abstract: Recently, neural networks have shown good
results for detection of a certain pattern in a given image. In
our previous papers [1-5], a fast algorithm for pattern
detection using neural networks was presented. Such
algorithm was designed based on cross correlation in the
frequency domain between the input image and the weights
of neural networks. Image conversion into symmetric shape
was established so that fast neural networks can give the
same results as conventional neural networks. Another
configuration of symmetry was suggested in [3,4] to improve
the speed up ratio. In this paper, our previous algorithm for
fast neural networks is developed. The frequency domain
cross correlation is modified in order to compensate for the
symmetric condition which is required by the input image.
Two new ideas are introduced to modify the cross correlation
algorithm. Both methods accelerate the speed of the fast
neural networks as there is no need for converting the input
image into symmetric one as previous. Theoretical and
practical results show that both approaches provide faster
speed up ratio than the previous algorithm.
Abstract: Buildings and associated construction methods have a significant impact on the environment. As construction activity increases in Kuwait, there is a need to create design and construction strategies which will minimize the environmental impact of new buildings. Green construction is a design philosophy intended to improve the sustainability of construction by the minimization of resource depletion and CO2 emissions throughout the life cycle of buildings. This paper presents and discusses the results of a survey that was conducted in Kuwait, with the objective of investigating the awareness of developers and other stakeholders regarding their understanding and use of green construction strategies. The results of the survey demonstrate that whilst there seems to be a reasonable level of awareness amongst the stakeholders, this awareness is not currently well reflected in the design and construction practices actually being applied. It is therefore concluded is there is a pressing need for intervention from Government in order that the use of sustainable green design and construction strategies becomes the norm in Kuwait.
Abstract: In a product development process, understanding the functional behavior of the system, the role of components in achieving functions and failure modes if components/subsystem fails its required function will help develop appropriate design validation and verification program for reliability assessment. The integration of these three issues will help design and reliability engineers in identifying weak spots in design and planning future actions and testing program. This case study demonstrate the advantage of unascertained theory described in the subjective cognition uncertainty, and then applies blind number (BN) theory in describing the uncertainty of the mechanical system failure process and the same time used the same theory in bringing out another mechanical reliability system model. The practical calculations shows the BN Model embodied the characters of simply, small account of calculation but betterforecasting capability, which had the value of macroscopic discussion to some extent.
Abstract: This paper introduces an adiabatic register file based
on two-phase CPAL (Complementary Pass-Transistor Adiabatic
Logic circuits) with power-gating scheme, which can operate on a
single-phase power clock. A 32×32 single-phase adiabatic register file
with power-gating scheme has been implemented with TSMC 0.18μm
CMOS technology. All the circuits except for the storage cells employ
two-phase CPAL circuits, and the storage cell is based on the
conventional memory one. The two-phase non-overlap power-clock
generator with power-gating scheme is used to supply the proposed
adiabatic register file. Full-custom layouts are drawn. The energy and
functional simulations have been performed using the net-list
extracted from their layouts. Compared with the traditional static
CMOS register file, HSPICE simulations show that the proposed
adiabatic register file can work very well, and it attains about 73%
energy savings at 100 MHz.
Abstract: There are many debates now regarding undervalued
and overvalued currencies currently traded on the world financial
market. This paper contributes to these debates from a theoretical
point of view. We present the three most commonly used methods of
estimating the equilibrium real effective exchange rate (REER):
macroeconomic balance approach, external sustainability approach
and equilibrium real effective exchange rate approach in the reduced
form. Moreover, we discuss key concepts of the calculation of the
real exchange rate (RER) based on applied explanatory variables:
nominal exchange rates, terms of trade and tradable and non-tradable
goods. Last but not least, we discuss the three main driving forces
behind real exchange rates movements which include terms of trade,
relative productivity growth and the interest rate differential.
Abstract: This paper presents a method for the optimal
allocation of Distributed generation in distribution systems. In this
paper, our aim would be optimal distributed generation allocation for
voltage profile improvement and loss reduction in distribution
network. Genetic Algorithm (GA) was used as the solving tool,
which referring two determined aim; the problem is defined and
objective function is introduced. Considering to fitness values
sensitivity in genetic algorithm process, there is needed to apply load
flow for decision-making. Load flow algorithm is combined
appropriately with GA, till access to acceptable results of this
operation. We used MATPOWER package for load flow algorithm
and composed it with our Genetic Algorithm. The suggested method
is programmed under MATLAB software and applied ETAP
software for evaluating of results correctness. It was implemented on
part of Tehran electricity distributing grid. The resulting operation of
this method on some testing system is illuminated improvement of
voltage profile and loss reduction indexes.
Abstract: During the year 1999, Serbia (ex Yugoslavia) and their northern province, Vojvodina, has been bombarded. Because of that general public believe is that this region was contaminated by depleted uranium and that there is a potential contaminant of agricultural products due to soil radioactivity. This paper presents the repeated analysis of agricultural soil samples in Vojvodina. The same investigation was carried out during the year 2001, and it was concluded that, based on the gamma-spectrometric analysis of 50 soil samples taken from the region of Vojvodina, there haven-t been registered any increase of radioactivity that could endanger the food production. We continue with the monitoring of this region. The comparison between those two sets of results is presented.
Abstract: In this paper, we propose a hardware and software
design method for automotive Electronic Control Units (ECU)
considering the functional safety. The proposed ECU is considered for
the application to Electro-Mechanical Actuator systems and the
validity of the design method is shown by the application to the
Electro-Mechanical Brake (EMB) control system which is used as a
brake actuator in Brake-By-Wire (BBW) systems. The importance of a
functional safety-based design approach to EMB ECU design has been
emphasized because of its safety-critical functions, which are executed
with the aid of many electric actuators, sensors, and application
software. Based on hazard analysis and risk assessment according to
ISO26262, the EMB system should be ASIL-D-compliant, the highest
ASIL level. To this end, an external signature watchdog and an
Infineon 32-bit microcontroller TriCore are used to reduce risks
considering common-cause hardware failure. Moreover, a software
design method is introduced for implementing functional
safety-oriented monitoring functions based on an asymmetric dual
core architecture considering redundancy and diversity. The validity
of the proposed ECU design approach is verified by using the EMB
Hardware-In-the-Loop (HILS) system, which consists of the EMB
assembly, actuator ECU, a host PC, and a few debugging devices.
Furthermore, it is shown that the existing sensor fault tolerant control
system can be used more effectively for mitigating the effects of
hardware and software faults by applying the proposed ECU design
method.
Abstract: In this paper, a new approach for target recognition based on the Empirical mode decomposition (EMD) algorithm of Huang etal. [11] and the energy tracking operator of Teager [13]-[14] is introduced. The conjunction of these two methods is called Teager-Huang analysis. This approach is well suited for nonstationary signals analysis. The impulse response (IR) of target is first band pass filtered into subsignals (components) called Intrinsic mode functions (IMFs) with well defined Instantaneous frequency (IF) and Instantaneous amplitude (IA). Each IMF is a zero-mean AM-FM component. In second step, the energy of each IMF is tracked using the Teager energy operator (TEO). IF and IA, useful to describe the time-varying characteristics of the signal, are estimated using the Energy separation algorithm (ESA) algorithm of Maragos et al .[16]-[17]. In third step, a set of features such as skewness and kurtosis are extracted from the IF, IA and IMF energy functions. The Teager-Huang analysis is tested on set of synthetic IRs of Sonar targets with different physical characteristics (density, velocity, shape,? ). PCA is first applied to features to discriminate between manufactured and natural targets. The manufactured patterns are classified into spheres and cylinders. One hundred percent of correct recognition is achieved with twenty three echoes where sixteen IRs, used for training, are free noise and seven IRs, used for testing phase, are corrupted with white Gaussian noise.
Abstract: The current education system in India is adept in
equipping and assessing the scholastic development of children.
However, there is an immediate need to strengthen co-scholastic
areas like life-skills, values and attitudes to equip students to face real
life challenges. Audio-visual technology and their respective media
can make a significant contribution to a value based learning
curriculum. Thus, co-scholastic skills need to be effectively nurtured
by a medium that is entertaining and impactful. Films in general have
a tremendous impact in our society. Films with a positive message
make a formidable learning experience that can influence and inspire
generations of learners. Leveraging on this powerful medium,
EduMedia India Pvt. Ltd. has introduced School Cinema a well
researched film-based learning module supported by a fun and
exciting workbook, designed to introduce and reaffirm life-skills and
values to children, thereby having a positive influence on their
attitudes.
Abstract: It is important problems to increase the detection rates
and reduce false positive rates in Intrusion Detection System (IDS).
Although preventative techniques such as access control and
authentication attempt to prevent intruders, these can fail, and as a
second line of defence, intrusion detection has been introduced. Rare
events are events that occur very infrequently, detection of rare
events is a common problem in many domains. In this paper we
propose an intrusion detection method that combines Rough set and
Fuzzy Clustering. Rough set has to decrease the amount of data and
get rid of redundancy. Fuzzy c-means clustering allow objects to
belong to several clusters simultaneously, with different degrees of
membership. Our approach allows us to recognize not only known
attacks but also to detect suspicious activity that may be the result of
a new, unknown attack. The experimental results on Knowledge
Discovery and Data Mining-(KDDCup 1999) Dataset show that the
method is efficient and practical for intrusion detection systems.
Abstract: The presented article deals with the description of a
numerical model of a corridor at a Central Interim Spent Fuel Storage
Facility (hereinafter CISFSF). The model takes into account the
effect of air flows on the temperature of stored waste. The
computational model was implemented in the ANSYS/CFX
programming environment in the form of a CFD task solution, which
was compared with an approximate analytical calculation. The article
includes a categorization of the individual alternatives for the
ventilation of such underground systems. The aim was to evaluate a
ventilation system for a CISFSF with regard to its stability and
capacity to provide sufficient ventilation for the removal of heat
produced by stored casks with spent nuclear fuel.
Abstract: In the past many uneconomic solutions for limitation
and interruption of short-circuit currents in low power applications
have been introduced, especially polymer switch based on the
positive temperature coefficient of resistance (PCTR) concept.
However there are many limitations in the active material, which
consists of conductive fillers. This paper presents a significantly
improved and simplified approach that replaces the existing current
limiters with faster switching elements. Its elegance lies in the
remarkable simplicity and low-cost processes of producing the device
using polyaniline (PANI) doped with methane-sulfonic acid (MSA).
Samples characterized as lying in the metallic and critical regimes of
metal insulator transition have been studied by means of electrical
performance in the voltage range from 1V to 5 V under different
environmental conditions. Moisture presence is shown to increase the
resistivity and also improved its current limiting performance.
Additionally, the device has also been studied for electrical resistivity
in the temperature range 77 K-300 K. The temperature dependence of
the electrical conductivity gives evidence for a transport mechanism
based on variable range hopping in three dimensions.
Abstract: This paper applies fuzzy AHP to evaluate the service
quality of online auction. Service quality is a composition of various
criteria. Among them many intangible attributes are difficult to
measure. This characteristic introduces the obstacles for respondents
on reply in the survey. So as to overcome this problem, we invite
fuzzy set theory into the measurement of performance and use AHP in
obtaining criteria. We found the most concerned dimension of service
quality is Transaction Safety Mechanism and the least is Charge Item.
Other criteria such as information security, accuracy and information
are too vital.
Abstract: The CMLP building was developed to be a model for
sustainability with strategies to reduce water, energy and pollution,
and to provide a healthy environment for the building occupants. The
aim of this paper is to investigate the environmental effects of energy
used by this building. A LCA (life cycle analysis) was led to measure
the real environmental effects produced by the use of energy. The
impact categories most affected by the energy use were found to be
the human health effects, as well as ecotoxicity. Natural gas
extraction, uranium milling for nuclear energy production, and the
blasting for mining and infrastructure construction are the processes
contributing the most to emissions in the human health effect. Data
comparing LCA results of CMLP building with a conventional
building results showed that energy used by the CMLP building has
less damage for the environment and human health than a
conventional building.
Abstract: In this paper we will consider the most known ratios
control schemes ((L/D, V/B),(L/D,V/F), Ryskamp-s, and
(D/(L+D),V/B)) for binary distillation column and we compare them
in the basis of interactions and disturbance propagation. The models
for these configurations are deuced using mathematical
transformations taking the energy balance structure (LV) as a base
model. The dynamic relative magnitude criterion (DRMC) is used to
assess the interactions. The results show that the introduction of
ratios in controlling the column tends to minimize the degree of
interactions between the loops.