Abstract: This experiment was conducted in attempt of
improving hydrodynamic efficiency of the propulsion mechanism by
installing a spring to the wing so that the opening angle of the wing in
one stroke can be changed automatically, compared to the existing
method of fixed maximum opening angle in Weis-Fogh type ship
propulsion mechanism. Average thrust coefficient was almost fixed
with all velocity ratio with the prototype, but with the spring type,
thrust coefficient increased sharply as velocity ratio increased.
Average propulsive efficiency was larger with bigger opening angle in
the prototype, but in the spring type, the one with smaller spring
coefficient had larger value. In the range over 1.0 in velocity ratio
where big thrust can be generated, spring type had more than twice of
propulsive efficiency increase compared to the prototype.
Abstract: In this paper, we present a technical and an economic
assessment of several sources of renewable energy in Saudi Arabia;
mainly solar, wind, hydro and biomass. We analyze the
environmental and climatic conditions in relation to these sources
and give an overview of some of the existing clean energy
technologies. Using standardized cost and efficiency data, we carry
out a cost benefit analysis to understand the economic factors
influencing the sustainability of energy production from renewable
sources in light of the energy cost and demand in the Saudi market.
Finally, we take a look at the Saudi petroleum industry and the
existing sources of conventional energy and assess the potential of
building a successful market for renewable energy under the
constraints imposed by the flow of subsidized cheap oil. We show
that while some renewable energy resources are well suited for
distributed or grid connected generation in the kingdom, their
viability is greatly undercut by the well developed and well
capitalized oil industry.
Abstract: Using 1km grid datasets representing monthly mean
precipitation, monthly mean temperature, and dry matter production
(DMP), we considered the regional plant production ability in
Southeast and South Asia, and also employed pixel-by-pixel
correlation analysis to assess the intensity of relation between climate
factors and plant production. While annual DMP in South Asia was
approximately less than 2,000kg, the one in most part of Southeast
Asia exceeded 2,500 - 3,000kg. It suggested that plant production in
Southeast Asia was superior to South Asia, however, Rain-Use
Efficiency (RUE) representing dry matter production per 1mm
precipitation showed that inland of Indochina Peninsula and India
were higher than islands in Southeast Asia. By the results of
correlation analysis between climate factors and DMP, while the area
in most parts of Indochina Peninsula indicated negative correlation
coefficients between DMP and precipitation or temperature, the area
in Malay Peninsula and islands showed negative correlation to
precipitation and positive one to temperature, and most part of India
dominating South Asia showed positive to precipitation and negative
to temperature. In addition, the areas where the correlation coefficients
exceeded |0.8| were regarded as “susceptible" to climate factors, and
the areas smaller than |0.2| were “insusceptible". By following the
discrimination, the map implying expected impacts by climate change
was provided.
Abstract: This paper gives an introduction to Web mining, then
describes Web Structure mining in detail, and explores the data
structure used by the Web. This paper also explores different Page
Rank algorithms and compare those algorithms used for Information
Retrieval. In Web Mining, the basics of Web mining and the Web
mining categories are explained. Different Page Rank based
algorithms like PageRank (PR), WPR (Weighted PageRank), HITS
(Hyperlink-Induced Topic Search), DistanceRank and DirichletRank
algorithms are discussed and compared. PageRanks are calculated for
PageRank and Weighted PageRank algorithms for a given hyperlink
structure. Simulation Program is developed for PageRank algorithm
because PageRank is the only ranking algorithm implemented in the
search engine (Google). The outputs are shown in a table and chart
format.
Abstract: New Growth Theory helps us make sense of the
ongoing shift from a resource-based economy to a knowledge-based
economy. It underscores the point that the economic processes which
create and diffuse new knowledge are critical to shaping the growth
of nations, communities and individual firms. In all too many
contributions to New (Endogenous) Growth Theory – though not in
all – central reference is made to 'a stock of knowledge', a 'stock of
ideas', etc., this variable featuring centre-stage in the analysis. Yet it
is immediately apparent that this is far from being a crystal clear
concept. The difficulty and uncertainty of being able to capture the
value associated with knowledge is a real problem. The intent of this
paper is introducing new thinking and theorizing about the
knowledge and its measurability in new growth theory. Moreover the
study aims to synthesize various strain of the literature with a
practical bearing on knowledge concept. By contribution of
institution framework which is found within NGT, we can indirectly
measure the knowledge concept. Institutions matter because they
shape the environment for production and employment of new
knowledge
Abstract: This paper discusses the design characteristics management accounting systems should have to be useful for strategic planning and control and provides brief introductions to strategic variance analysis, profit-linked performance measurement models and balanced scorecard. It shows two multi-period, multiproduct models are specified, can be related to Porter's strategy framework and cost and revenue drivers, and can be used to support strategic planning, control and cost management.
Abstract: Warranty is a powerful marketing tool for the
manufacturer and a good protection for both the manufacturer and the
customer. However, warranty always involves additional costs to the
manufacturer, which depend on product reliability characteristics and
warranty parameters. This paper presents an approach to optimisation
of warranty parameters for known product failure distribution to
reduce the warranty costs to the manufacturer while retaining the
promotional function of the warranty. Combination free replacement
and pro-rata warranty policy is chosen as a model and the length of
free replacement period and pro-rata policy period are varied, as well
as the coefficients that define the pro-rata cost function. Multiparametric
warranty optimisation is done by using genetic algorithm.
Obtained results are guideline for the manufacturer to choose the
warranty policy that minimises the costs and maximises the profit.
Abstract: This paper presents ageing experiments controlled by the evolution of junction parameters. The deterioration of the device is related to high injection effects which modified the transport mechanisms in the space charge region of the junction. Physical phenomena linked to the degradation of junction parameters that affect the devices reliability are reported and discussed. We have used the method based on numerical analysis of experimental current-voltage characteristic of the junction, in order to extract the electrical parameters. The simultaneous follow-up of the evolutions of the series resistance and of the transition voltage allow us to introduce a new parameter for reliability evaluation.
Abstract: Almost all Libyan industries (both private and public) have struggled with many difficulties during the past three decades due to many problems. These problems have created a strongly negative impact on the productivity and utilization of many companies within Libya. This paper studies the current awareness and implementation levels of Just-In-Time (JIT) within the Libyan Textile private industry. A survey has been applied in this study using an intensive detailed questionnaire. Based on the analysis of the survey responses, the results show that the management body within the surveyed companies has a modest strategy towards most of the areas that are considered as being very crucial in any successful implementation of JIT. The results also show a variation within the implementation levels of the JIT elements as these varies between Low and Acceptable levels. The paper has also identified limitations within the investigated areas within this industry, and has pointed to areas where senior managers within the Libyan textile industry should take immediate actions in order to achieve effective implementation of JIT within their companies.
Abstract: Data Envelopment Analysis (DEA) is a methodology
that computes efficiency values for decision making units (DMU) in a
given period by comparing the outputs with the inputs. In many cases,
there are some time lag between the consumption of inputs and the
production of outputs. For a long-term research project, it is hard to
avoid the production lead time phenomenon. This time lag effect
should be considered in evaluating the performance of organizations.
This paper suggests a model to calculate efficiency values for the
performance evaluation problem with time lag. In the experimental
part, the proposed methods are compared with the CCR and an
existing time lag model using the data set of the 21st century frontier
R&D program which is a long-term national R&D program of Korea.
Abstract: A structural study of an aqueous electrolyte whose
experimental results are available. It is a solution of LiCl-6H2O type
at glassy state (120K) contrasted with pure water at room temperature
by means of Partial Distribution Functions (PDF) issue from neutron
scattering technique. Based on these partial functions, the Reverse
Monte Carlo method (RMC) computes radial and angular correlation
functions which allow exploring a number of structural features of
the system. The obtained curves include some artifacts. To remedy
this, we propose to introduce a screened potential as an additional
constraint. Obtained results show a good matching between
experimental and computed functions and a significant improvement
in PDFs curves with potential constraint. It suggests an efficient fit of
pair distribution functions curves.
Abstract: Overcurrent (OC) relays are the major protection
devices in a distribution system. The operating time of the OC relays
are to be coordinated properly to avoid the mal-operation of the
backup relays. The OC relay time coordination in ring fed
distribution networks is a highly constrained optimization problem
which can be stated as a linear programming problem (LPP). The
purpose is to find an optimum relay setting to minimize the time of
operation of relays and at the same time, to keep the relays properly
coordinated to avoid the mal-operation of relays.
This paper presents two phase simplex method for optimum time
coordination of OC relays. The method is based on the simplex
algorithm which is used to find optimum solution of LPP. The
method introduces artificial variables to get an initial basic feasible
solution (IBFS). Artificial variables are removed using iterative
process of first phase which minimizes the auxiliary objective
function. The second phase minimizes the original objective function
and gives the optimum time coordination of OC relays.
Abstract: Localized surface plasmon resonance (LSPR) is the
coherent oscillation of conductive electrons confined in noble
metallic nanoparticles excited by electromagnetic radiation, and
nanosphere lithography (NSL) is one of the cost-effective methods to
fabricate metal nanostructures for LSPR. NSL can be categorized
into two major groups: dispersed NSL and closely pack NSL. In
recent years, gold nanocrescents and gold nanoholes with vertical
sidewalls fabricated by dispersed NSL, and silver nanotriangles and
gold nanocaps on silica nanospheres fabricated by closely pack NSL,
have been reported for LSPR biosensing. This paper introduces
several novel gold nanostructures fabricated by NSL in LSPR
applications, including 3D nanostructures obtained by evaporating
gold obliquely on dispersed nanospheres, nanoholes with slant
sidewalls, and patchy nanoparticles on closely packed nanospheres,
all of which render satisfactory sensitivity for LSPR sensing. Since
the LSPR spectrum is very sensitive to the shape of the metal
nanostructures, formulas are derived and software is developed for
calculating the profiles of the obtainable metal nanostructures by
NSL, for different nanosphere masks with different fabrication
conditions. The simulated profiles coincide well with the profiles of
the fabricated gold nanostructures observed under scanning electron
microscope (SEM) and atomic force microscope (AFM), which
proves that the software is a useful tool for the process design of
different LSPR nanostructures.
Abstract: Chua’s circuit is one of the most important electronic devices that are used for Chaos and Bifurcation studies. A central role of secure communication is devoted to it. Since the adaptive control is used vastly in the linear systems control, here we introduce a new trend of application of adaptive method in the chaos controlling field. In this paper, we try to derive a new adaptive control scheme for Chua’s circuit controlling because control of chaos is often very important in practical operations. The novelty of this approach is for sake of its robustness against the external perturbations which is simulated as an additive noise in all measured states and can be generalized to other chaotic systems. Our approach is based on Lyapunov analysis and the adaptation law is considered for the feedback gain. Because of this, we have named it NAFT (Nonlinear Adaptive Feedback Technique). At last, simulations show the capability of the presented technique for Chua’s circuit.
Abstract: Palladium-catalyzed hydrodechlorination is a
promising alternative for the treatment of environmentally relevant
water bodies, such as groundwater, contaminated with chlorinated
organic compounds (COCs). In the aqueous phase
hydrodechlorination of COCs, Pd-based catalysts were found to have
a very high catalytic activity. However, the full utilization of the
catalyst-s potential is impeded by the sensitivity of the catalyst to
poisoning and deactivation induced by reduced sulfur compounds
(e.g. sulfides). Several regenerants have been tested before to recover
the performance of sulfide-fouled Pd catalyst. But these only
delivered partial success with respect to re-establishment of the
catalyst activity. In this study, the deactivation behaviour of
Pd/Al2O3 in the presence of sulfide was investigated. Subsequent to
total deactivation the catalyst was regenerated in the aqueous phase
using potassium permanganate. Under neutral pH condition,
oxidative regeneration with permanganate delivered a slow recovery
of catalyst activity. However, changing the pH of the bulk solution to
acidic resulted in the complete recovery of catalyst activity within a
regeneration time of about half an hour. These findings suggest the
superiority of permanganate as regenerant in re-activating Pd/Al2O3
by oxidizing Pd-bound sulfide.
Abstract: We present a new method for the fully automatic 3D
reconstruction of the coronary artery centerlines, using two X-ray
angiogram projection images from a single rotating monoplane
acquisition system. During the first stage, the input images are
smoothed using curve evolution techniques. Next, a simple yet
efficient multiscale method, based on the information of the Hessian
matrix, for the enhancement of the vascular structure is introduced.
Hysteresis thresholding using different image quantiles, is used to
threshold the arteries. This stage is followed by a thinning procedure
to extract the centerlines. The resulting skeleton image is then pruned
using morphological and pattern recognition techniques to remove
non-vessel like structures. Finally, edge-based stereo correspondence
is solved using a parallel evolutionary optimization method based on
f symbiosis. The detected 2D centerlines combined with disparity
map information allow the reconstruction of the 3D vessel
centerlines. The proposed method has been evaluated on patient data
sets for evaluation purposes.
Abstract: In this paper we introduce an approach via optimization methods to find approximate solutions for nonlinear Fredholm integral equations of the first kind. To
this purpose, we consider two stages of approximation.
First we convert the integral equation to a moment problem and then we modify the new problem to two classes of optimization problems, non-constraint optimization problems
and optimal control problems. Finally numerical examples is
proposed.
Abstract: It is necessary to evaluate the bridges conditions and
strengthen bridges or parts of them. The reinforcement necessary due
to some reasons can be summarized as: First, a changing in use of
bridge could produce internal forces in a part of structural which
exceed the existing cross-sectional capacity. Second, bridges may
also need reinforcement because damage due to external factors
which reduced the cross-sectional resistance to external loads. One of
other factors could listed here its misdesign in some details, like
safety of bridge or part of its.This article identify the design demands
of Qing Shan bridge located in is in Heilongjiang Province He gang -
Nen Jiang Road 303 provincial highway, Wudalianchi area, China, is
an important bridge in the urban areas. The investigation program
was include the observation and evaluate the damage in T- section
concrete beams , prestressed concrete box girder bridges section in
additional evaluate the whole state of bridge includes the pier ,
abutments , bridge decks, wings , bearing and capping beam, joints,
........etc. The test results show that the bridges in general structural
condition are good. T beam span No 10 were observed, crack
extended upward along the ribbed T beam, and continue to the T
beam flange. Crack width varying between 0.1mm to 0.4mm, the
maximum about 0.4mm. The bridge needs to be improved flexural
bending strength especially at for T beam section.
Abstract: In this paper, to optimize the “Characteristic Straight Line Method" which is used in the soil displacement analysis, a “best estimate" of the geodetic leveling observations has been achieved by taking in account the concept of 'Height systems'. This concept has been discussed in detail and consequently the concept of “height". In landslides dynamic analysis, the soil is considered as a mosaic of rigid blocks. The soil displacement has been monitored and analyzed by using the “Characteristic Straight Line Method". Its characteristic components have been defined constructed from a “best estimate" of the topometric observations. In the measurement of elevation differences, we have used the most modern leveling equipment available. Observational procedures have also been designed to provide the most effective method to acquire data. In addition systematic errors which cannot be sufficiently controlled by instrumentation or observational techniques are minimized by applying appropriate corrections to the observed data: the level collimation correction minimizes the error caused by nonhorizontality of the leveling instrument's line of sight for unequal sight lengths, the refraction correction is modeled to minimize the refraction error caused by temperature (density) variation of air strata, the rod temperature correction accounts for variation in the length of the leveling rod' s Invar/LO-VAR® strip which results from temperature changes, the rod scale correction ensures a uniform scale which conforms to the international length standard and the introduction of the concept of the 'Height systems' where all types of height (orthometric, dynamic, normal, gravity correction, and equipotential surface) have been investigated. The “Characteristic Straight Line Method" is slightly more convenient than the “Characteristic Circle Method". It permits to evaluate a displacement of very small magnitude even when the displacement is of an infinitesimal quantity. The inclination of the landslide is given by the inverse of the distance reference point O to the “Characteristic Straight Line". Its direction is given by the bearing of the normal directed from point O to the Characteristic Straight Line (Fig..6). A “best estimate" of the topometric observations was used to measure the elevation of points carefully selected, before and after the deformation. Gross errors have been eliminated by statistical analyses and by comparing the heights within local neighborhoods. The results of a test using an area where very interesting land surface deformation occurs are reported. Monitoring with different options and qualitative comparison of results based on a sufficient number of check points are presented.
Abstract: A filter is used to remove undesirable frequency information from a dynamic signal. This paper shows that the Znotch filter filtering technique can be applied to remove the noise nuisance from a machining signal. In machining, the noise components were identified from the sound produced by the operation of machine components itself such as hydraulic system, motor, machine environment and etc. By correlating the noise components with the measured machining signal, the interested components of the measured machining signal which was less interfered by the noise, can be extracted. Thus, the filtered signal is more reliable to be analysed in terms of noise content compared to the unfiltered signal. Significantly, the I-kaz method i.e. comprises of three dimensional graphical representation and I-kaz coefficient, Z∞ could differentiate between the filtered and the unfiltered signal. The bigger space of scattering and the higher value of Z∞ demonstrated that the signal was highly interrupted by noise. This method can be utilised as a proactive tool in evaluating the noise content in a signal. The evaluation of noise content is very important as well as the elimination especially for machining operation fault diagnosis purpose. The Z-notch filtering technique was reliable in extracting noise component from the measured machining signal with high efficiency. Even though the measured signal was exposed to high noise disruption, the signal generated from the interaction between cutting tool and work piece still can be acquired. Therefore, the interruption of noise that could change the original signal feature and consequently can deteriorate the useful sensory information can be eliminated.