Abstract: The aerodynamics characteristics of a blended-wing body (BWB) aircraft were obtained in Universiti Teknologi MARA low speed wind tunnel. The scaled-down of BWB model consisted of a canard as its horizontal stabilizer. There were four canards with different aspect ratio used in the experiments. Canard setting angles were varied from -20q to 20q. All tests were conducted at velocity of 35 m/s, with Mach number 0.1. At low angles of attacks, the increment of lift slope for various canards aspect ratio is small and almost constant. Higher canard aspect ratio will cause higher drag. However, canard has a high effect to the moment at zero lift, CM,0.The visualization using mini tuff was performed to observe the airflow at the upper surface of canard. KeywordsAerodynamics,blended-wing body, canard, wind tunnel.
Abstract: This analysis investigates the distortion of flow
measurement and the increase of cavitation along orifice
flowmeter. The analysis using the numerical method (CFD)
validated the distortion of flow measurement through the inlet
velocity profile considering the convergence and grid
dependency. Realizable k-e model was selected and y+ was
about 50 in this numerical analysis. This analysis also estimated
the vulnerability of cavitation effect due to inlet velocity profile.
The investigation concludes that inclined inlet velocity profile
could vary the pressure which was measured at pressure tab
near pipe wall and it led to distort the pressure values ranged
from -3.8% to 5.3% near the orifice plate and to make the
increase of cavitation. The investigation recommends that the
fully developed inlet velocity flow is beneficial to accurate flow
measurement in orifice flowmeter.
Abstract: Physiological control of a left ventricle assist device (LVAD) is generally a complicated task due to diverse operating environments and patient variability. In this work, a tracking control algorithm based on sliding mode and feed forward control for a class of discrete-time single input single output (SISO) nonlinear uncertain systems is presented. The controller was developed to track the reference trajectory to a set operating point without inducing suction in the ventricle. The controller regulates the estimated mean pulsatile flow Qp and mean pulsatility index of pump rotational speed PIω that was generated from a model of the assist device. We recall the principle of the sliding mode control theory then we combine the feed-forward control design with the sliding mode control technique to follow the reference trajectory. The uncertainty is replaced by its upper and lower boundary. The controller was tested in a computer simulation covering two scenarios (preload and ventricular contractility). The simulation results prove the effectiveness and the robustness of the proposed controller
Abstract: In order to study floristic and molecular classification
of common wild wheat (Triticum boeoticum Boiss.), an analysis was
conducted on populations of the Triticum boeoticum collected from
different regions of Iran. Considering all floristic compositions of
habitats, six floristic groups (syntaxa) within the populations were
identified. A high level of variation of T. boeoticum also detected
using SSR markers. Our results showed that molecular method
confirmed the grouping of floristic method. In other word, the results
from our study indicate that floristic classification are still useful,
efficient, and economic tools for characterizing the amount and
distribution of genetic variation in natural populations of T.
boeoticum. Nevertheless, molecular markers appear as useful and
complementary techniques for identification and for evaluation of
genetic diversity in studied populations.
Abstract: The problem discussed in this paper involves packing fresh fish fileet of the northern Cod into a standard square container. The fish is first cleaned and split and then collected on a belt ready to be stacked in a container. The aim of our work is to pack the fish into the container with constraints on the amount of overlap allowed for the fileets. The current focus is to design a packing cell that can be real-time and of practical use, while finding the optimal solution to the degree of overlap and minimise the unused space of the container.
Abstract: The numerical simulation of the slip effect via
vicoelastic fluid for 4:1 contraction problem is investigated with
regard to kinematic behaviors of streamlines and stress tensor by
models of the Navier-Stokes and Oldroyd-B equations. Twodimensional
spatial reference system of incompressible creeping flow
with and without slip velocity is determined and the finite element
method of a semi-implicit Taylor-Galerkin pressure-correction is
applied to compute the problem of this Cartesian coordinate system
including the schemes of velocity gradient recovery method and the
streamline-Upwind / Petrov-Galerkin procedure. The slip effect at
channel wall is added to calculate after each time step in order to
intend the alteration of flow path. The result of stress values and the
vortices are reduced by the optimum slip coefficient of 0.1 with near
the outcome of analytical solution.
Abstract: Column leach test has been performed to examine the
behavior of leaching of sodium, calcium and potassium in landfills.
In the column leach apparatus, two different layers of contaminated
and uncontaminated soils of different height ratios (ratio of depth of
contaminated soil to the depth of uncontaminated soil) are taken.
Water is poured from an overhead tank at a particular flowrate to the
inlet of the soil column for a certain ponding depth over the
contaminated soil. Subsequent infiltration causes leaching and the
leachates are collected from the bottom of the column. The
concentrations of Na, Ca and K in the leachate are measured using
flame photometry. The experiments are further extended by changing
the rates of flow from the overhead tank to the inlet of the column in
achieving the same ponding depth. The experiments are performed
for different scenarios in which the height ratios are altered and the
variations of concentrations of Na, Ca, and K are observed. The study
brings an estimation of leaching in landfill sites for different heights
and precipitation intensity where a ponding depth is maintained over
the landfill. It has been observed that the leaching behavior of Na,
Ca, and K are not similar. Calcium exhibits highest amount of
leaching compared to Sodium and Potassium under similar
experimental conditions.
Abstract: This paper proposes a new decision making structure
to determine the appropriate product delivery strategy for different products in a manufacturing system among make-to-stock, make-toorder,
and hybrid strategy. Given product delivery strategies for all products in the manufacturing system, the position of the Order
Penetrating Point (OPP) can be located regarding the delivery strategies among which location of OPP in hybrid strategy is a
cumbersome task. In this regard, we employ analytic network process, because there are varieties of interrelated driving factors
involved in choosing the right location. Moreover, the proposed structure is augmented with fuzzy sets theory in order to cope with
the uncertainty of judgments. Finally, applicability of the proposed structure is proven in practice through a real industrial case company.
The numerical results demonstrate the efficiency of the proposed decision making structure in order partitioning and OPP location.
Abstract: Automatic keyphrase extraction is useful in efficiently
locating specific documents in online databases. While several
techniques have been introduced over the years, improvement on
accuracy rate is minimal. This research examines attribute scores for
author-supplied keyphrases to better understand how the scores affect
the accuracy rate of automatic keyphrase extraction. Five attributes
are chosen for examination: Term Frequency, First Occurrence, Last
Occurrence, Phrase Position in Sentences, and Term Cohesion
Degree. The results show that First Occurrence is the most reliable
attribute. Term Frequency, Last Occurrence and Term Cohesion
Degree display a wide range of variation but are still usable with
suggested tweaks. Only Phrase Position in Sentences shows a totally
unpredictable pattern. The results imply that the commonly used
ranking approach which directly extracts top ranked potential phrases
from candidate keyphrase list as the keyphrases may not be reliable.
Abstract: In this study it is aimed to determine the level of preservice teachers- computer phobia. Whether or not computer phobia meaningfully varies statistically according to gender and computer experience has been tested in the study. The study was performed on 430 pre-service teachers at the Education Faculty in Rize/Turkey. Data in the study were collected through the Computer Phobia Scale consisting of the “Personal Knowledge Questionnaire", “Computer Anxiety Rating Scale", and “Computer Thought Survey". In this study, data were analyzed with statistical processes such as t test, and correlation analysis. According to results of statistical analyses, computer phobia of male pre-service teachers does not statistically vary depending on their gender. Although male preservice teachers have higher computer anxiety scores, they have lower computer thought scores. It was also observed that there is a negative and intensive relation between computer experience and computer anxiety. Meanwhile it was found out that pre-service teachers using computer regularly indicated lower computer anxiety. Obtained results were tried to be discussed in terms of the number of computer classes in the Education Faculty curriculum, hours of computer class and the computer availability of student teachers.
Abstract: In this paper we use data mining techniques to investigate factors that contribute significantly to enhancing the risk of acute coronary syndrome. We assume that the dependent variable is diagnosis – with dichotomous values showing presence or absence of disease. We have applied binary regression to the factors affecting the dependent variable. The data set has been taken from two different cardiac hospitals of Karachi, Pakistan. We have total sixteen variables out of which one is assumed dependent and other 15 are independent variables. For better performance of the regression model in predicting acute coronary syndrome, data reduction techniques like principle component analysis is applied. Based on results of data reduction, we have considered only 14 out of sixteen factors.
Abstract: In this study, solid phase micro-extraction (SPME)
was optimized to improve the sensitivity and accuracy in
formaldehyde determination for plywood panels. Further work has
been carried out to compare the newly developed technique with
existing method which reacts formaldehyde collected in desiccators
with acetyl acetone reagent (DC-AA). In SPME, formaldehyde was
first derivatized with O-(2,3,4,5,6 pentafluorobenzyl)-hydroxylamine
hydrochloride (PFBHA) and analysis was then performed by gas
chromatography in combination with mass spectrometry (GC-MS).
SPME data subjected to various wood species gave satisfactory
results, with relative standard deviations (RSDs) obtained in the
range of 3.1-10.3%. It was also well correlated with DC values,
giving a correlation coefficient, RSQ, of 0.959. The quantitative
analysis of formaldehyde by SPME was an alternative in wood
industry with great potential
Abstract: In this paper we describe our efforts to design and
implement an agent development framework that has the potential to
scale to the size of any underlying network suitable for various ECommerce
activities. The main novelty in our framework is it-s
capability to allow the development of sophisticated, secured agents
which are simple enough to be practical.
We have adopted FIPA agent platform reference Model as
backbone for implementation along with XML for agent
Communication and Java Cryptographic Extension and architecture
to realize the security of communication information between agents.
The advantage of our architecture is its support of agents
development in different languages and Communicating with each
other using a more open standard i.e. XML
Abstract: Character segmentation is an important preprocessing
step for text recognition. In degraded documents, existence of
touching characters decreases recognition rate drastically, for any
optical character recognition (OCR) system. In this paper we have
proposed a complete solution for segmenting touching characters in
all the three zones of printed Gurmukhi script. A study of touching
Gurmukhi characters is carried out and these characters have been
divided into various categories after a careful analysis. Structural
properties of the Gurmukhi characters are used for defining the
categories. New algorithms have been proposed to segment the
touching characters in middle zone, upper zone and lower zone.
These algorithms have shown a reasonable improvement in
segmenting the touching characters in degraded printed Gurmukhi
script. The algorithms proposed in this paper are applicable only to
machine printed text. We have also discussed a new and useful
technique to segment the horizontally overlapping lines.
Abstract: The paper provides biomasses characteristics by
proximate analysis (volatile matter, fixed carbon and ash) and
ultimate analysis (carbon, hydrogen, nitrogen and oxygen) for the
prediction of the heating value equations. The heating value
estimation of various biomasses can be used as an energy evaluation.
Thirteen types of biomass were studied. Proximate analysis was
investigated by mass loss method and infrared moisture analyzer.
Ultimate analysis was analyzed by CHNO analyzer. The heating
values varied from 15 to 22.4MJ kg-1. Correlations of the calculated
heating value with proximate and ultimate analyses were undertaken
using multiple regression analysis and summarized into three and two
equations, respectively. Correlations based on proximate analysis
illustrated that deviation of calculated heating values from
experimental heating values was higher than the correlations based
on ultimate analysis.
Abstract: The paper presents the virtual model of the active
suspension system used for improving the dynamic behavior of a
motor vehicle. The study is focused on the design of the control
system, the purpose being to minimize the effect of the road
disturbances (which are considered as perturbations for the control
system). The analysis is performed for a quarter-car model, which
corresponds to the suspension system of the front wheel, by using the
DFC (Design for Control) software solution EASY5 (Engineering
Analysis Systems) of MSC Software. The controller, which is a PIDbased
device, is designed through a parametric optimization with the
Matrix Algebra Tool (MAT), considering the gain factors as design
variables, while the design objective is to minimize the overshoot of
the indicial response.
Abstract: The aim of this paper is to investigate the effect of
mean size of industry on survival of new firms in East-Azarbaijan
province through 1981-2006 using hazard function. So the effect of
two variables including mean employment of industry and mean
capital of industry are investigated on firm's survival. The Industry &
Mine Ministry database has used for data gathering and the data are
analyzed using the semi-parametric cox regression model. The results
of this study shows that there is a meaningful negative relationship
between mean capital of industry and firm's survival, but the mean
employment of industry has no meaningful effect on survival of new
firms.
Abstract: Power system stability enhancement by simultaneous tuning of a Power System Stabilizer (PSS) and a Static Var Compensator (SVC)-based controller is thoroughly investigated in this paper. The coordination among the proposed damping stabilizers and the SVC internal voltage regulators has also been taken into consideration. The design problem is formulated as an optimization problem with a time-domain simulation-based objective function and Real-Coded Genetic Algorithm (RCGA) is employed to search for optimal controller parameters. The proposed stabilizers are tested on a weakly connected power system with different disturbances and loading conditions. The nonlinear simulation results are presented to show the effectiveness and robustness of the proposed control schemes over a wide range of loading conditions and disturbances. Further, the proposed design approach is found to be robust and improves stability effectively even under small disturbance and unbalanced fault conditions.
Abstract: Surface roughness (Ra) is one of the most important requirements in machining process. In order to obtain better surface roughness, the proper setting of cutting parameters is crucial before the process take place. This research presents the development of mathematical model for surface roughness prediction before milling process in order to evaluate the fitness of machining parameters; spindle speed, feed rate and depth of cut. 84 samples were run in this study by using FANUC CNC Milling α-Τ14ιE. Those samples were randomly divided into two data sets- the training sets (m=60) and testing sets(m=24). ANOVA analysis showed that at least one of the population regression coefficients was not zero. Multiple Regression Method was used to determine the correlation between a criterion variable and a combination of predictor variables. It was established that the surface roughness is most influenced by the feed rate. By using Multiple Regression Method equation, the average percentage deviation of the testing set was 9.8% and 9.7% for training data set. This showed that the statistical model could predict the surface roughness with about 90.2% accuracy of the testing data set and 90.3% accuracy of the training data set.
Abstract: Mechanical buckling analysis of rectangular plates
with central circular cutout is performed in this paper. The finiteelement
method is used to study the effects of plate-support
conditions, aspect ratio, and hole size on the mechanical buckling
strength of the perforated plates subjected to linearly varying loading.
Results show that increasing the hole size does not necessarily reduce
the mechanical buckling strength of the perforated plates. It is also
concluded that the clamped boundary condition increases the
mechanical buckling strength of the perforated plates more than the
simply-supported boundary condition and the free boundary
conditions enhance the mechanical buckling strength of the
perforated plates more effectively than the fixed boundary conditions.
Furthermore, for the bending cases, the critical buckling load of
perforated plates with free edges is less than perforated plates with
fixed edges.