Abstract: Composite material based on Fe3Si micro-particles
and Mn-Zn nano-ferrite was prepared using powder metallurgy
technology. The sol-gel followed by autocombustion process was
used for synthesis of Mn0.8Zn0.2Fe2O4 ferrite. 3 wt.% of mechanically
milled ferrite was mixed with Fe3Si powder alloy. Mixed micro-nano
powder system was homogenized by the Resonant Acoustic Mixing
using ResodynLabRAM Mixer. This non-invasive homogenization
technique was used to preserve spherical morphology of Fe3Si
powder particles. Uniaxial cold pressing in the closed die at pressure
600 MPa was applied to obtain a compact sample. Microwave
sintering of green compact was realized at 800°C, 20 minutes, in air.
Density of the powders and composite was measured by
Hepycnometry. Impulse excitation method was used to measure
elastic properties of sintered composite. Mechanical properties were
evaluated by measurement of transverse rupture strength (TRS) and
Vickers hardness (HV). Resistivity was measured by 4 point probe
method. Ferrite phase distribution in volume of the composite was
documented by metallographic analysis.
It has been found that nano-ferrite particle distributed among
micro- particles of Fe3Si powder alloy led to high relative density
(~93%) and suitable mechanical properties (TRS >100 MPa, HV
~1GPa, E-modulus ~140 GPa) of the composite. High electric
resistivity (R~6.7 ohm.cm) of prepared composite indicate their
potential application as soft magnetic material at medium and high
frequencies.
Abstract: Since, it is essential to provide homeless people by the
earthquake with safe, habitable accommodation repairing medium
and slight levels of damage at the connection parts should be
undertaken. In order to prove that a repaired connection was
sufficiently strong, a precast beam to column post tensioned
connection was tested in three phases. In phase one, the middle level
damage was observed at 6% drift at these connections. As a result of
the extra loads applied, little damage was observed. In the last phase,
the four connections tested in the first phase were repaired using
epoxy resin and then retested. The results from the tests on the
repaired precast and the undamaged specimens showed that the
repaired specimens were sufficiently strong, thus proving that repair
to damaged precast beam to column post tensioned connections can
be undertaken.
Abstract: Various personality profile tests are used to identify
personality strengths and limits in individuals, helping both
individuals and managers to optimize work and team effort in
organizations. One such test, the Hartman’s personality profile,
emphasizes four driving "core motives" influenced or affected by
both strengths and limitations classified into four colors: Red -
motivated by power; Blue - discipline and loyalty; White - peace; and
Yellow – fun loving. Two shortcomings of Hartman’s personality test
are noted; 1) only one selection for every item / situation allowed and
2) selection of an item / option even if not applicable. A test taker
may be as much nurturing as he is opinionated but since
“opinionated” seems less attractive the individual would likely select
nurturing, causing a misidentification in personality strengths and
limits. Since few individuals have a “strong” personality, it is
difficult to assess their true personality strengths and limits allowing
only one choice or requiring unwanted choices, undermining the
potential of the test. We modified Hartman’s personality profile
allowing test takers to make either multiple choices for any item /
situation or leave them blank if applicable. Sixty-eight participants
(38 males and 30 females), 17 - 49 years old, from countries in Asia,
Europe, N. America, CIS, Africa, Latin America, and Oceania were
included. 58 participants (85.3%) reported the modified test, allowing
multiple / no choices better identified their personality strengths and
limits, while 10 participants (14.7%) expressed the original (one
choice version) was sufficient. The overall results show that our
modified test enhanced the identification and balance of core
personalities’ strengths and limits, aiding test takers, managers and
organizations to better assess individual characteristics, particularly
useful in making task-related, teamwork, and management decisions.
Abstract: Microbial fuel cells (MFCs) represent a promising
technology for simultaneous bioelectricity generation and wastewater
treatment. Catalysts are significant portions of the cost of microbial
fuel cell cathodes. Many materials have been tested as aqueous
cathodes, but air-cathodes are needed to avoid energy demands for
water aeration. The sluggish oxygen reduction reaction (ORR) rate at
air cathode necessitates efficient electrocatalyst such as carbon
supported platinum catalyst (Pt/C) which is very costly. Manganese
oxide (MnO2) was a representative metal oxide which has been
studied as a promising alternative electrocatalyst for ORR and has
been tested in air-cathode MFCs. However the single MnO2 has poor
electric conductivity and low stability. In the present work, the MnO2
catalyst has been modified by doping Pt nanoparticle. The goal of the
work was to improve the performance of the MFC with minimum Pt
loading. MnO2 and Pt nanoparticles were prepared by hydrothermal
and sol gel methods, respectively. Wet impregnation method was
used to synthesize Pt/MnO2 catalyst. The catalysts were further used
as cathode catalysts in air-cathode cubic MFCs, in which anaerobic
sludge was inoculated as biocatalysts and palm oil mill effluent
(POME) was used as the substrate in the anode chamber. The asprepared
Pt/MnO2 was characterized comprehensively through field
emission scanning electron microscope (FESEM), X-Ray diffraction
(XRD), X-ray photoelectron spectroscopy (XPS), and cyclic
voltammetry (CV) where its surface morphology, crystallinity,
oxidation state and electrochemical activity were examined,
respectively. XPS revealed Mn (IV) oxidation state and Pt (0)
nanoparticle metal, indicating the presence of MnO2 and Pt.
Morphology of Pt/MnO2 observed from FESEM shows that the
doping of Pt did not cause change in needle-like shape of MnO2
which provides large contacting surface area. The electrochemical
active area of the Pt/MnO2 catalysts has been increased from 276 to
617 m2/g with the increase in Pt loading from 0.2 to 0.8 wt%. The
CV results in O2 saturated neutral Na2SO4 solution showed that
MnO2 and Pt/MnO2 catalysts could catalyze ORR with different
catalytic activities. MFC with Pt/MnO2 (0.4 wt% Pt) as air cathode
catalyst generates a maximum power density of 165 mW/m3, which
is higher than that of MFC with MnO2 catalyst (95 mW/m3). The
open circuit voltage (OCV) of the MFC operated with MnO2 cathode
gradually decreased during 14 days of operation, whereas the MFC
with Pt/MnO2 cathode remained almost constant throughout the
operation suggesting the higher stability of the Pt/MnO2 catalyst.
Therefore, Pt/MnO2 with 0.4 wt% Pt successfully demonstrated as an
efficient and low cost electrocatalyst for ORR in air cathode MFC with higher electrochemical activity, stability and hence enhanced
performance.
Abstract: Vehicular Adhoc Network (VANET) is a new
technology which aims to ensure intelligent inter-vehicle
communications, seamless internet connectivity leading to improved
road safety, essential alerts, and access to comfort and entertainment.
VANET operations are hindered by mobile node’s (vehicles)
uncertain mobility. Routing algorithms use metrics to evaluate which
path is best for packets to travel. Metrics like path length (hop count),
delay, reliability, bandwidth, and load determine optimal route. The
proposed scheme exploits link quality, traffic density, and
intersections as routing metrics to determine next hop. This study
enhances Geographical Routing Protocol (GRP) using fuzzy
controllers while rules are optimized with Bee Swarm Optimization
(BSO). Simulations results are compared to conventional GRP.
Abstract: This study was developed to compare the behavior
and the ability of polymer foam composites towards sound absorption
test of Shorea leprosula wood (SL) of acid hydrolysis treatment with
particle size
Abstract: The web’s increased popularity has included a huge
amount of information, due to which automated web page
classification systems are essential to improve search engines’
performance. Web pages have many features like HTML or XML
tags, hyperlinks, URLs and text contents which can be considered
during an automated classification process. It is known that Webpage
classification is enhanced by hyperlinks as it reflects Web page
linkages. The aim of this study is to reduce the number of features to
be used to improve the accuracy of the classification of web pages. In
this paper, a novel feature selection method using an improved
Particle Swarm Optimization (PSO) using principle of evolution is
proposed. The extracted features were tested on the WebKB dataset
using a parallel Neural Network to reduce the computational cost.
Abstract: This work reports the potential of using Palm Kernel
(PK) ash and shell as a partial substitute for Portland Cement (PC)
and coarse aggregate in the development of mortar and concrete. PK
ash and shell are agro-waste materials from palm oil mills, the
disposal of PK ash and shell is an environmental problem of concern.
The PK ash has pozzolanic properties that enables it as a partial
replacement for cement and also plays an important role in the
strength and durability of concrete, its use in concrete will alleviate
the increasing challenges of scarcity and high cost of cement. In order
to investigate the PC replacement potential of PK ash, three types of
PK ash were produced at varying temperature (350-750C) and they
were used to replace up to 50% PC. The PK shell was used to replace
up to 100% coarse aggregate in order to study its aggregate
replacement potential. The testing programme included material
characterisation, the determination of compressive strength, tensile
splitting strength and chemical durability in aggressive sulfatebearing
exposure conditions. The 90 day compressive results showed
a significant strength gain (up to 26.2 N/mm2). The Portland cement
and conventional coarse aggregate has significantly higher influence
in the strength gain compared to the equivalent PK ash and PK shell.
The chemical durability results demonstrated that after a prolonged
period of exposure, significant strength losses in all the concretes
were observed. This phenomenon is explained, due to lower change
in concrete morphology and inhibition of reaction species and the
final disruption of the aggregate cement paste matrix.
Abstract: A numerical study of natural convection heat transfer
in water filled cavity has been examined in 3-Dfor single phase liquid
cooling system by using an array of parallel plate fins mounted to one
wall of a cavity. The heat generated by a heat source represents a
computer CPU with dimensions of 37.5∗37.5mm mounted on
substrate. A cold plate is used as a heat sink installed on the opposite
vertical end of the enclosure. The air flow inside the computer case is
created by an exhaust fan. A turbulent air flow is assumed and k-ε
model is applied. The fins are installed on the substrate to enhance
the heat transfer. The applied power energy range used is between 15
- 40W. In order to determine the thermal behaviour of the cooling
system, the effect of the heat input and the number of the parallel
plate fins are investigated. The results illustrate that as the fin number
increases the maximum heat source temperature decreases. However,
when the fin number increases to critical value the temperature start
to increase due to the fins are too closely spaced and that cause the
obstruction of water flow. The introduction of parallel plate fins
reduces the maximum heat source temperature by 10% compared to
the case without fins. The cooling system maintains the maximum
chip temperature at 64.68°C when the heat input was at 40W that is
much lower than the recommended computer chips limit temperature
of no more than 85°C and hence the performance of the CPU is
enhanced.
Abstract: In this study, we have focused our attention on
combining of molecular imprinting into nanofilms and QCM
nanosensor approaches and producing QCM nanosensor for anti-
CCP, chosen as model protein, using anti-CCP imprinted nanofilms.
The nonimprinted nanosensor was also prepared to evaluate the
selectivity of the imprinted nanosensor. Anti-CCP imprinted QCM
nanosensor was tested for real time detection of anti-CCP from
aqueous solution. The kinetic and affinity studies were determined by
using anti-CCP solutions with different concentrations. The
responses related with mass shifts (%m) and frequency shifts (%f)
were used to evaluate adsorption properties. To show the selectivity
of the anti-CCP imprinted QCM nanosensor, competitive adsorption
of anti-CCP and IgM was investigated. The results indicate that anti-
CCP imprinted QCM nanosensor has higher adsorption capabilities
for anti-CCP than for IgM, due to selective cavities in the polymer
structure.
Abstract: A large amount of data is typically stored in relational
databases (DB). The latter can efficiently handle user queries which
intend to elicit the appropriate information from data sources.
However, direct access and use of this data requires the end users to
have an adequate technical background, while they should also cope
with the internal data structure and values presented. Consequently
the information retrieval is a quite difficult process even for IT or DB
experts, taking into account the limited contributions of relational
databases from the conceptual point of view. Ontologies enable users
to formally describe a domain of knowledge in terms of concepts and
relations among them and hence they can be used for unambiguously
specifying the information captured by the relational database.
However, accessing information residing in a database using
ontologies is feasible, provided that the users are keen on using
semantic web technologies. For enabling users form different
disciplines to retrieve the appropriate data, the design of a Graphical
User Interface is necessary. In this work, we will present an
interactive, ontology-based, semantically enable web tool that can be
used for information retrieval purposes. The tool is totally based on
the ontological representation of underlying database schema while it
provides a user friendly environment through which the users can
graphically form and execute their queries.
Abstract: Environmental impact assessment techniques have
been developed as a result of the worldwide efforts to reduce the
environmental impact of global warming. By using the quantification
method in the construction industry, it is now possible to manage the
greenhouse gas is to systematically evaluate the impact on the
environment over the entire construction process. In particular, the
proportion of greenhouse gas emissions at the production stage of
construction material occupied is high, and efforts are needed in
particular in the construction field.
In this research, intended for concrete products for the construction
materials, by using the LCA method, we compared the results of
environmental impact assessment and carbon emissions of developing
products that have been applied low-carbon technologies compared to
existing products. As a results, by introducing a raw material of
industrial waste, showed carbon reduction. Through a comparison of
the carbon emission reduction effect of low carbon technologies, it is
intended to provide academic data for the evaluation of greenhouse
gases in the construction sector and the development of low carbon
technologies of the future.
Abstract: The purpose of this paper is to examine the hypothesis
explaining the mechanism in the case, where the product is deleted or
reduced the fundamental function of the product through the product
concept changes in the digital camera industry. This paper points out
not owning the fundamental technology might cause the change of the
product concept. Casio could create new competitive factor so that this
paper discusses a possibility of the mechanism of changing the product
concept.
Abstract: In this paper, an analysis of some model order
reduction techniques is presented. A new hybrid algorithm for model
order reduction of linear time invariant systems is compared with the
conventional techniques namely Balanced Truncation, Hankel Norm
reduction and Dominant Pole Algorithm (DPA). The proposed hybrid
algorithm is known as Clustering Dominant Pole Algorithm (CDPA),
is able to compute the full set of dominant poles and its cluster center
efficiently. The dominant poles of a transfer function are specific
eigenvalues of the state space matrix of the corresponding dynamical
system. The effectiveness of this novel technique is shown through
the simulation results.
Abstract: In rapid industrial development, the demand for
high-strength and lightweight materials have been increased. Thus,
various CFRP (Carbon Fiber Reinforced Plastics) with composite
materials are being used. The design variables of CFRP are its
lamination direction, order and thickness. Thus, the hardness and
strength of CFRP depends much on their design variables. In this
paper, the lamination direction of CFRP was used to produce a
symmetrical ply [0°/0°, -15°/+15°, -30°/+30°, -45°/+45°, -60°/+60°,
-75°/+75° and 90°/90°] and an asymmetrical ply [0°/15°, 0°/30°,
0°/45°, 0°/60° 0°/75° and 0°/90°]. The bending flexure stress of the
CFRP specimen was evaluated through a bending test. Its thermal
property was measured using an infrared camera. The symmetrical
specimen and the asymmetrical specimen were analyzed. The results
showed that the asymmetrical specimen increased the bending loads
according to the increase in the orientation angle; and from 0°, the
symmetrical specimen showed a tendency opposite the asymmetrical
tendency because the tensile force of fiber differs at the vertical
direction of its load. Also, the infrared camera showed that the thermal
property had a trend similar to that of the mechanical properties.
Abstract: The wear measuring and wear modelling are
fundamental issues in the industrial field, mainly correlated to the
economy and safety. Therefore, there is a need to study the wear
measurements and wear estimation. Pin-on-disc test is the most
common test which is used to study the wear behaviour. In this paper,
the pin-on-disc (AEROTECH UNIDEX 11) is used for the
investigation of the effects of normal load and hardness of material on
the wear under dry and sliding conditions. In the pin-on-disc rig, two
specimens were used; one, a pin is made of steel with a tip, positioned
perpendicular to the disc, where the disc is made of aluminium. The
pin wear and disc wear were measured by using the following
instruments: The Talysurf instrument, a digital microscope, and the
alicona instrument. The Talysurf profilometer was used to measure
the pin/disc wear scar depth, digital microscope was used to measure
the diameter and width of wear scar, and the alicona was used to
measure the pin wear and disc wear. After that, the Archard model,
American Society for Testing and Materials model (ASTM), and
neural network model were used for pin/disc wear modelling.
Simulation results were implemented by using the Matlab program.
This paper focuses on how the alicona can be used for wear
measurements and how the neural network can be used for wear
estimation.
Abstract: In order to study the aerodynamic performance of a
semi-flexible membrane wing, Fluid-Structure Interaction simulations
have been performed. The fluid problem has been modeled using
two different approaches which are the vortex panel method and the
numerical solution of the Navier-Stokes equations. Nonlinear analysis
of the structural problem is performed using the Finite Element
Method. Comparison between the two fluid solvers has been made.
Aerodynamic performance of the wing is discussed regarding its
lift and drag coefficients and they are compared with those of the
equivalent rigid wing.
Abstract: Agriculture is the backbone of economy of Pakistan
and cotton is the major agricultural export and supreme source of raw
fiber for our textile industry. To combat severe problems of insect
and weed, combination of three genes namely Cry1Ac, Cry2A and
EPSPS genes was transferred in locally cultivated cotton variety
MNH-786 with the use of Agrobacterium mediated genetic
transformation. The present study focused on the molecular screening
of transgenic cotton plants at T3 generation in order to confirm
integration and expression of all three genes (Cry1Ac, Cry2A and
EPSP synthase) into the cotton genome. Initially, glyphosate spray
assay was used for screening of transgenic cotton plants containing
EPSP synthase gene at T3 generation. Transgenic cotton plants which
were healthy and showed no damage on leaves were selected after 07
days of spray. For molecular analysis of transgenic cotton plants in
the laboratory, the genomic DNA of these transgenic cotton plants
were isolated and subjected to amplification of the three genes. Thus,
seventeen out of twenty (Cry1Ac gene), ten out of twenty (Cry2A
gene) and all twenty (EPSP synthase gene) were produced positive
amplification. On the base of PCR amplification, ten transgenic plant
samples were subjected to protein expression analysis through
ELISA. The results showed that eight out of ten plants were actively
expressing the three transgenes. Real-time PCR was also done to
quantify the mRNA expression levels of Cry1Ac and EPSP synthase
gene. Finally, eight plants were confirmed for the presence and active
expression of all three genes at T3 generation.
Abstract: A computational fluid dynamics (CFD) model is
developed for rechargeable non-aqueous electrolyte lithium-air
batteries with a partial opening for oxygen supply to the cathode.
Multi-phase transport phenomena occurred in the battery are
considered, including dissolved lithium ions and oxygen gas in the
liquid electrolyte, solid-phase electron transfer in the porous
functional materials and liquid-phase charge transport in the
electrolyte. These transport processes are coupled with the
electrochemical reactions at the active surfaces, and effects of
discharge reaction-generated solid Li2O2 on the transport properties
and the electrochemical reaction rate are evaluated and implemented
in the model. The predicted results are discussed and analyzed in terms
of the spatial and transient distribution of various parameters, such as
local oxygen concentration, reaction rate, variable solid Li2O2 volume
fraction and porosity, as well as the effective diffusion coefficients. It
is found that the effect of the solid Li2O2 product deposited at the solid
active surfaces is significant on the transport phenomena and the
overall battery performance.
Abstract: This study examines analytically the effect of tsunami loads on reinforced concrete (RC) frame buildings. The impact of tsunami wave loads and waterborne objects are analyzed using a typical substandard full-scale two-story RC frame building tested as part of the EU-funded Ecoleader project. The building was subjected to shake table tests in bare condition, and subsequently strengthened using Carbon Fiber Reinforced Polymers (CFRP) composites and retested. Numerical models of the building in both bare and CFRP-strengthened conditions are calibrated in DRAIN-3DX software to match the test results. To investigate the response of wave loads and impact forces, the numerical models are subjected to nonlinear dynamic analyses using force time-history input records. The analytical results are compared in terms of displacements at the floors and at the “impact point” of a boat. The results show that the roof displacement of the CFRP-strengthened building reduced by 63% when compared to the bare building. The results also indicate that strengthening only the mid-height of the impact column using CFRP is more effective at reducing damage when compared to strengthening other parts of the column. Alternative solutions to mitigate damage due to tsunami loads are suggested.