Abstract: Speckle noise affects all coherent imaging systems
including medical ultrasound. In medical images, noise suppression
is a particularly delicate and difficult task. A tradeoff between noise
reduction and the preservation of actual image features has to be made
in a way that enhances the diagnostically relevant image content.
Even though wavelets have been extensively used for denoising
speckle images, we have found that denoising using contourlets gives
much better performance in terms of SNR, PSNR, MSE, variance and
correlation coefficient. The objective of the paper is to determine the
number of levels of Laplacian pyramidal decomposition, the number
of directional decompositions to perform on each pyramidal level and
thresholding schemes which yields optimal despeckling of medical
ultrasound images, in particular. The proposed method consists of the
log transformed original ultrasound image being subjected to contourlet
transform, to obtain contourlet coefficients. The transformed
image is denoised by applying thresholding techniques on individual
band pass sub bands using a Bayes shrinkage rule. We quantify the
achieved performance improvement.
Abstract: Experiments have been performed to investigate the radiation effects on mixed convection heat transfer for thermally developing airflow in vertical ducts with two differentially heated isothermal walls and two adiabatic walls. The investigation covers the Reynolds number Re = 800 to Re = 2900, heat flux varied from 256 W/m2 to 863 W/m2, hot wall temperature ranges from 27°C to 100 °C, aspect ratios 1 & 0.5 and the emissivity of internal walls are 0.05 and 0.85. In the present study, combined flow visualization was conducted to observe the flow patterns. The effect of surface temperature along the walls was studied to investigate the local Nusselt number variation within the duct. The result shows that flow condition and radiation significantly affect the total Nusselt number and tends to reduce the buoyancy condition.
Abstract: In this paper, a new method of image edge-detection
and characterization is presented. “Parametric Filtering method" uses
a judicious defined filter, which preserves the signal correlation
structure as input in the autocorrelation of the output. This leads,
showing the evolution of the image correlation structure as well as
various distortion measures which quantify the deviation between
two zones of the signal (the two Hamming signals) for the protection
of an image edge.
Abstract: The complexity of lignocellulosic biomass requires
a pretreatment step to improve the yield of fermentable sugars. The
efficient pretreatment of corn cobs using microwave and potassium
hydroxide and enzymatic hydrolysis was investigated. The
objective of this work was to characterize the optimal condition of
pretreatment of corn cobs using microwave and potassium
hydroxide enhance enzymatic hydrolysis. Corn cobs were
submerged in different potassium hydroxide concentration at varies
temperature and resident time. The pretreated corn cobs were
hydrolyzed to produce the reducing sugar for analysis. The
morphology and microstructure of samples were investigated by
Thermal gravimetric analysis (TGA, scanning electron microscope
(SEM), X-ray diffraction (XRD). The results showed that lignin
and hemicellulose were removed by microwave/potassium
hydroxide pretreatment. The crystallinity of the pretreated corn
cobs was higher than the untreated. This method was compared
with autoclave and conventional heating method. The results
indicated that microwave-alkali treatment was an efficient way to
improve the enzymatic hydrolysis rate by increasing its
accessibility hydrolysis enzymes.
Abstract: Heat transfer from two cam shape cylinder in tandem
arrangement had been studied numerically.
The distance between the centers of cylinders (L) is allowed to
vary to change the longitudinal pitch ratio (L/Deq). The equivalent
diameter of the cylinder (Deq) is 27.6 mm and longitudinal pitch ratio
varies in range 2
Abstract: Mercury is a natural occurring element and present in
various concentrations in the environment. Due to its toxic effects, it
is desirable to research mercury sensitive materials to adsorb
mercury. This paper describes the preparation of Au nanoparticles for
mercury adsorption by using a microwave (MW)-polyol method in
the presence of three different Sodium Chloride (NaCl)
concentrations (10, 20 and 30 mM). Mixtures of spherical, triangular,
octahedral, decahedral particles and 1-D product were obtained using
this rapid method. Sizes and shapes was found strongly depend on the
concentrations of NaCl. Without NaCl concentration, spherical,
triangular plates, octahedral, decahedral nanoparticles and 1D
product were produced. At the lower NaCl concentration (10 mM),
spherical, octahedral and decahedral nanoparticles were present,
while spherical and decahedral nanoparticles were preferentially form
by using 20 mM of NaCl concentration. Spherical, triangular plates,
octahedral and decahedral nanoparticles were obtained at the highest
NaCl concentration (30 mM). The amount of mercury adsorbed using
20 ppm mercury solution is the highest (67.5 %) for NaCl
concentration of 30 mM. The high yield of polygonal particles will
increase the mercury adsorption. In addition, the adsorption of
mercury is also due to the sizes of the particles. The sizes of particles
become smaller with increasing NaCl concentrations (size ranges, 5-
16 nm) than those synthesized without addition of NaCl (size ranges
11-32 nm). It is concluded that NaCl concentrations affects the
formation of sizes and shapes of Au nanoparticles thus affects the
mercury adsorption.
Abstract: In recent years a number of applications with multirobot
systems (MRS) is growing in various areas. But their design
is in practice often difficult and algorithms are proposed for the
theoretical background and do not consider errors and noise in real
conditions, so they are not usable in real environment. These errors
are visible also in task of target localization enough, when robots
try to find and estimate the position of the target by the sensors.
Localization of target is possible also with one robot but as it was
examined target finding and localization with group of mobile robots
can estimate the target position more accurately and faster. The
accuracy of target position estimation is made by cooperation of
MRS and particle filtering. Advantage of usage the MRS with particle
filtering was tested on task of fixed target localization by group of
mobile robots.
Abstract: School homework has been synonymous with students- life in Chinese national type primary schools in Malaysia. Although many reports in the press claimed that students were burdened with too much of it, homework continues to be a common practice in national type schools that is believed to contribute to academic achievement. This study is conducted to identify the relationship between the burden of school homework and academic achievement among pupils in Chinese National Type Primary School in the state of Perak, Malaysia. A total of 284 students (142 from urban and 142 from rural) respectively were chosen as participants in this study. Variables of gender and location (urban/rural areas) has shown significant difference in student academic achievement. Female Chinese student from rural areas showed a higher mean score than males from urban area. Therefore, the Chinese language teachers should give appropriate and relevant homework to primary school students to achieve good academic performance.
Abstract: Shrunken patterning for integrated device
manufacturing requires surface cleanliness and surface smoothness in
wet chemical processing [1]. It is necessary to control all process
parameters perfectly especially for the common cleaning technique
RCA clean (SC-1 and SC-2) [2]. In this paper the characteristic and
effect of surface preparation parameters are discussed. The properties
of RCA wet chemical processing in silicon technology is based on
processing time, temperature, concentration and megasonic power of
SC-1 and QDR. An improvement of wafer surface preparation by
the enhanced variables of the wet cleaning chemical process is
proposed.
Abstract: In recent years application of natural antimicrobials
instead of conventional ones, due to their hazardous effects on health,
has got serious attentions. On the basis of the results of different
studies, chitosan, a natural bio-degradable and non-toxic
biopolysaccharide derived from chitin, has potential to be used as a
natural antimicrobial. Chitosan has exhibited high antimicrobial
activity against a wide variety of pathogenic and spoilage
microorganisms, including fungi, and Gram-positive and Gramnegative
bacteria. The antimicrobial action is influenced by intrinsic
factors such as the type of chitosan, the degree of chitosan
polymerization and extrinsic factors such as the microbial organism,
the environmental conditions and presence of the other components.
The use of chitosan in food systems should be based on sufficient
knowledge of the complex mechanisms of its antimicrobial mode of
action. In this article we review a number of studies on the
investigation of chitosan antimicrobial properties and application of
them in culture and food mediums.
Abstract: Continuously growing needs for Internet applications
that transmit massive amount of data have led to the emergence of
high speed network. Data transfer must take place without any
congestion and hence feedback parameters must be transferred from
the receiver end to the sender end so as to restrict the sending rate in
order to avoid congestion. Even though TCP tries to avoid
congestion by restricting the sending rate and window size, it never
announces the sender about the capacity of the data to be sent and
also it reduces the window size by half at the time of congestion
therefore resulting in the decrease of throughput, low utilization of
the bandwidth and maximum delay. In this paper, XCP protocol is
used and feedback parameters are calculated based on arrival rate,
service rate, traffic rate and queue size and hence the receiver
informs the sender about the throughput, capacity of the data to be
sent and window size adjustment, resulting in no drastic decrease in
window size, better increase in sending rate because of which there is
a continuous flow of data without congestion. Therefore as a result of
this, there is a maximum increase in throughput, high utilization of
the bandwidth and minimum delay. The result of the proposed work
is presented as a graph based on throughput, delay and window size.
Thus in this paper, XCP protocol is well illustrated and the various
parameters are thoroughly analyzed and adequately presented.
Abstract: Current mode circuits like current conveyors are
getting significant attention in current analog ICs design due to their
higher band-width, greater linearity, larger dynamic range, simpler
circuitry, lower power consumption and less chip area. The second
generation current controlled conveyor (CCCII) has the advantage of
electronic adjustability over the CCII i.e. in CCCII; adjustment of the
X-terminal intrinsic resistance via a bias current is possible. The
presented approach is based on the CMOS implementation of second
generation positive (CCCII+), negative (CCCII-) and dual Output
Current Controlled Conveyor (DOCCCII) and its application as
Universal filter. All the circuits have been designed and simulated
using 65nm CMOS technology model parameters on Cadence
Virtuoso / Spectre using 1V supply voltage. Various simulations have
been carried out to verify the linearity between output and input
ports, range of operation frequency, etc. The outcomes show good
agreement between expected and experimental results.
Abstract: The steam cracking reactions are always accompanied with the formation of coke which deposits on the walls of the tubular reactors. The investigation has attempted to control catalytic coking by the applying aluminum, zinc and ceramic coating like aluminum-magnesium by thermal spray and pack cementation method. Rate of coke formation during steam cracking of naphtha has been investigated both for uncoated stainless steel (with different alloys) and metal coating constructed with thermal Spray and pack cementation method with metal powders of Aluminum, Aluminum-Magnesium, zinc, silicon, nickel and chromium. The results of the study show that passivating the surface of SS321 with a coating of Aluminum and Aluminum-Magnesium can significantly reduce the rate of coke deposition during naphtha pyrolysis. SEM and EDAX techniques (Philips XL Series) were used to examine the coke deposits formed by the metal-hydrocarbon reactions. Our objective was to separate the different stages by identifying the characteristic morphologies.
Abstract: Total liquid ventilation can support gas exchange in animal models of lung injury. Clinical application awaits further technical improvements and performance verification. Our aim was to develop a liquid ventilator, able to deliver accurate tidal volumes, and a computerized system for measuring lung mechanics. The computer-assisted, piston-driven respirator controlled ventilatory parameters that were displayed and modified on a real-time basis. Pressure and temperature transducers along with a lineal displacement controller provided the necessary signals to calculate lung mechanics. Ten newborn lambs (
Abstract: In present work are considered the scheme of
evaluation the transition probability in quantum system. It is based on
path integral representation of transition probability amplitude and its
evaluation by means of a saddle point method, applied to the part of
integration variables. The whole integration process is reduced to
initial value problem solutions of Hamilton equations with a random
initial phase point. The scheme is related to the semiclassical initial
value representation approaches using great number of trajectories. In
contrast to them from total set of generated phase paths only one path
for each initial coordinate value is selected in Monte Karlo process.
Abstract: In the current study, we have conducted an experimental investigation on the utilization of electronic arc furnace (EAF) reducing slag for the absorption of CO2 via wet grinding method. It was carried out by various grinding conditions. The slag was ground in the vibrating ball mill in the presence of CO2 and pure water under ambient temperature. The reaction behavior was monitored with constant pressure method, and the changes of experimental systems volume as a function of grinding time were measured. It was found that the CO2 absorption occurred as soon as the grinding started. The CO2 absorption was significantly increased in the case of wet grinding compare to the dry grinding. Generally, the amount of CO2 absorption increased as the amount of water, weight of slag and initial pressure increased. However, it was decreased when the amount of water exceeds 200ml and when smaller balls were used. The absorption of CO2 occurred simultaneously with the start of the grinding and it stopped when the grinding was stopped. According to this research, the CO2 reacted with the CaO inside the slag, forming CaCO3.
Abstract: This study aims to examine the factors affecting
knowledge sharing behavior in knowledge-based electronic communities (e-communities) because quantity and quality of
knowledge shared among the members play a critical role in the community-s sustainability. Past research has suggested three
perspectives that may affect the quantity and quality of knowledge
shared: economics, social psychology, and social ecology. In this
study, we strongly believe that an economic perspective may be suitable to validate factors influencing newly registered members-
knowledge contribution at the beginning of relationship development.
Accordingly, this study proposes a model to validate the factors influencing members- knowledge sharing based on Transaction Cost
Theory. By doing so, we may empirically test our hypotheses in various types of e-communities to determine the generalizability of our research models.
Abstract: This paper presents an architecture of current filesystem
implementations as well as our new filesystem SpadFS and operating
system Spad with rewritten VFS layer targeted at high performance
I/O applications. The paper presents microbenchmarks and real-world
benchmarks of different filesystems on the same kernel as well as
benchmarks of the same filesystem on different kernels – enabling
the reader to make conclusion how much is the performance of
various tasks affected by operating system and how much by physical
layout of data on disk. The paper describes our novel features–most
notably continuous allocation of directories and cross-file readahead
– and shows their impact on performance.
Abstract: Although water only takes a little percentage in the total mass of soil, it indeed plays an important role to the strength of structure. Moisture transfer can be carried out by many different mechanisms which may involve heat and mass transfer, thermodynamic phase change, and the interplay of various forces such as viscous, buoyancy, and capillary forces. The continuum models are not well suited for describing those phenomena in which the connectivity of the pore space or the fracture network, or that of a fluid phase, plays a major role. However, Lattice Boltzmann methods (LBMs) are especially well suited to simulate flows around complex geometries. Lattice Boltzmann methods were initially invented for solving fluid flows. Recently, fluid with multicomponent and phase change is also included in the equations. By comparing the numerical result with experimental result, the Lattice Boltzmann methods with phase change will be optimized.
Abstract: An effective approach for realizing the binary tree structure, representing a combinational logic functionality with enhanced throughput, is discussed in this paper. The optimization in maximum operating frequency was achieved through delay minimization, which in turn was possible by means of reducing the depth of the binary network. The proposed synthesis methodology has been validated by experimentation with FPGA as the target technology. Though our proposal is technology independent, yet the heuristic enables better optimization in throughput even after technology mapping for such Boolean functionality; whose reduced CNF form is associated with a lesser literal cost than its reduced DNF form at the Boolean equation level. For cases otherwise, our method converges to similar results as that of [12]. The practical results obtained for a variety of case studies demonstrate an improvement in the maximum throughput rate for Spartan IIE (XC2S50E-7FT256) and Spartan 3 (XC3S50-4PQ144) FPGA logic families by 10.49% and 13.68% respectively. With respect to the LUTs and IOBUFs required for physical implementation of the requisite non-regenerative logic functionality, the proposed method enabled savings to the tune of 44.35% and 44.67% respectively, over the existing efficient method available in literature [12].