Abstract: With respect to the dissipation of energy through
plastic deformation of joints of prefabricated wall units, the paper
points out the principal importance of efficient reinforcement of the
prefabricated system at its joints. The method, quality and amount of
reinforcement are essential for reaching the necessary degree of joint
ductility. The paper presents partial results of experimental research
of vertical joints of prefabricated units exposed to monotonously
rising loading and repetitive shear force and formulates a conclusion
that the limit state of the structure as a whole is preceded by the
disintegration of joints, or that the structure tends to pass from
linearly elastic behaviour to non-linearly elastic to plastic behaviour
by exceeding the proportional elastic limit in joints.Experimental
verification on a model of a 7-storey prefabricated structure revealed
weak points in its load-bearing systems, mainly at places of critical
points around openings situated in close proximity to vertical joints
of mutually perpendicularly oriented walls.
Abstract: The aim of this paper is to propose a mathematical
model to determine invariant sets, set covering, orbits and, in
particular, attractors in the set of tourism variables. Analysis was
carried out based on a pre-designed algorithm and applying our
interpretation of chaos theory developed in the context of General
Systems Theory. This article sets out the causal relationships
associated with tourist flows in order to enable the formulation of
appropriate strategies. Our results can be applied to numerous cases.
For example, in the analysis of tourist flows, these findings can be
used to determine whether the behaviour of certain groups affects that
of other groups and to analyse tourist behaviour in terms of the most
relevant variables. Unlike statistical analyses that merely provide
information on current data, our method uses orbit analysis to
forecast, if attractors are found, the behaviour of tourist variables in
the immediate future.
Abstract: Fuel cell's system requires regulating circuit for
voltage and current in order to control power in case of connecting to
other generative devices or load. In this paper Fuel cell system and
convertor, which is a multi-variable system, are controlled using
sliding mode method. Use of weighting matrix in design procedure
made it possible to regulate speed of control. Simulation results show
the robustness and accuracy of proposed controller for controlling
desired of outputs.
Abstract: This paper addresses the problem of blind source separation
(BSS). To recover original signals, from linear instantaneous
mixtures, we propose a new contrast function based on the use of a
double referenced system. Our approach assumes statistical independence
sources. The reference vectors will be incrusted in the cumulant
to evaluate the independence. The estimation of the separating matrix
will be performed in two steps: whitening observations and joint
diagonalization of a set of referenced cumulant matrices. Computer
simulations are presented to demonstrate the effectiveness of the
suggested approach.
Abstract: In recent years, sustainable supply chain management
(SSCM) has been widely researched in academic domain. However,
due to the traditional operational role and the complexity of supply
chain management in the cement industry, a relatively small amount
of research has been conducted on cement supply chain simulation
integrated with sustainability criteria. This paper analyses the cement
supply chain operations using the Push-Pull supply chain
frameworks, the Life Cycle Assessment (LCA) methodology; and
proposal integration approach, proposes three supply chain scenarios
based on Make-To-Stock (MTS), Pack-To-Order (PTO) and Grind-
To-Order (GTO) strategies. A Discrete-Event Simulation (DES)
model of SSCM is constructed using Arena software to implement
the three-target scenarios. We conclude with the simulation results
that (GTO) is the optimal supply chain strategy that demonstrates the
best economic, ecological and social performance in the cement
industry.
Abstract: Because of increasing demands for security in today-s
society and also due to paying much more attention to machine
vision, biometric researches, pattern recognition and data retrieval in
color images, face detection has got more application. In this article
we present a scientific approach for modeling human skin color, and
also offer an algorithm that tries to detect faces within color images
by combination of skin features and determined threshold in the
model. Proposed model is based on statistical data in different color
spaces. Offered algorithm, using some specified color threshold, first,
divides image pixels into two groups: skin pixel group and non-skin
pixel group and then based on some geometric features of face
decides which area belongs to face.
Two main results that we received from this research are as follow:
first, proposed model can be applied easily on different databases and
color spaces to establish proper threshold. Second, our algorithm can
adapt itself with runtime condition and its results demonstrate
desirable progress in comparison with similar cases.
Abstract: In this paper a unified approach via block-pulse functions (BPFs) or shifted Legendre polynomials (SLPs) is presented to solve the linear-quadratic-Gaussian (LQG) control problem. Also a recursive algorithm is proposed to solve the above problem via BPFs. By using the elegant operational properties of orthogonal functions (BPFs or SLPs) these computationally attractive algorithms are developed. To demonstrate the validity of the proposed approaches a numerical example is included.
Abstract: Internet infrastructures in most places of the world
have been supported by the advancement of optical fiber technology,
most notably wavelength division multiplexing (WDM) system.
Optical technology by means of WDM system has revolutionized
long distance data transport and has resulted in high data capacity,
cost reductions, extremely low bit error rate, and operational
simplification of the overall Internet infrastructure. This paper
analyses and compares the system impairments, which occur at data
transmission rates of 2.5Gb/s and 10 Gb/s per wavelength channel in
our proposed optical WDM system for Internet infrastructure in
Tanzania. The results show that the data transmission rate of 2.5 Gb/s
has minimum system impairments compared with a rate of 10 Gb/s
per wavelength channel, and achieves a sufficient system
performance to provide a good Internet access service.
Abstract: Static Var Compensator (SVC) is a shunt type FACTS
device which is used in power system primarily for the purpose of
voltage and reactive power control. In this paper, a fuzzy logic based
supplementary controller for Static Var Compensator (SVC) is
developed which is used for damping the rotor angle oscillations and
to improve the transient stability of the power system. Generator
speed and the electrical power are chosen as input signals for the
Fuzzy Logic Controller (FLC). The effectiveness and feasibility of
the proposed control is demonstrated with Single Machine Infinite
Bus (SMIB) system and multimachine system (WSCC System)
which show improvement over the use of a fixed parameter
controller.
Abstract: The sanitary sewerage connection rate becomes an
important indicator of advanced cities. Following the construction of
sanitary sewerages, the maintenance and management systems are
required for keeping pipelines and facilities functioning well. These
maintenance tasks often require sewer workers to enter the manholes
and the pipelines, which are confined spaces short of natural
ventilation and full of hazardous substances. Working in sewers could
be easily exposed to a risk of adverse health effects. This paper
proposes the use of Bayesian belief networks (BBN) as a higher level
of noncarcinogenic health risk assessment of sewer workers. On the
basis of the epidemiological studies, the actual hospital attendance
records and expert experiences, the BBN is capable of capturing the
probabilistic relationships between the hazardous substances in sewers
and their adverse health effects, and accordingly inferring the
morbidity and mortality of the adverse health effects. The provision of
the morbidity and mortality rates of the related diseases is more
informative and can alleviate the drawbacks of conventional methods.
Abstract: The security of power systems against malicious cyberphysical
data attacks becomes an important issue. The adversary
always attempts to manipulate the information structure of the power
system and inject malicious data to deviate state variables while
evading the existing detection techniques based on residual test. The
solutions proposed in the literature are capable of immunizing the
power system against false data injection but they might be too costly
and physically not practical in the expansive distribution network.
To this end, we define an algebraic condition for trustworthy power
system to evade malicious data injection. The proposed protection
scheme secures the power system by deterministically reconfiguring
the information structure and corresponding residual test. More
importantly, it does not require any physical effort in either microgrid
or network level. The identification scheme of finding meters being
attacked is proposed as well. Eventually, a well-known IEEE 30-bus
system is adopted to demonstrate the effectiveness of the proposed
schemes.
Abstract: The Artificial immune systems algorithms are Meta
heuristic optimization method, which are used for clustering and
pattern recognition applications are abundantly. These algorithms in
multimodal optimization problems are more efficient than genetic
algorithms. A major drawback in these algorithms is their slow
convergence to global optimum and their weak stability can be
considered in various running of these algorithms. In this paper,
improved Artificial Immune System Algorithm is introduced for the
first time to overcome its problems of artificial immune system. That
use of the small size of a local search around the memory antibodies
is used for improving the algorithm efficiently. The credibility of the
proposed approach is evaluated by simulations, and it is shown that
the proposed approach achieves better results can be achieved
compared to the standard artificial immune system algorithms
Abstract: Access to information is the key to the empowerment of everybody despite where they are living. This research is to be carried out in respect of the people living in developing countries, considering their plight and complex geographical, demographic, social-economic conditions surrounding the areas they live, which hinder access to information and of professionals providing services such as medical workers, which has led to high death rates and development stagnation. Research on Unified Communications and Integrated Collaborations (UCIC) system in the health sector of developing countries comes in to create a possible solution of bridging the digital canyon among the communities. The aim is to deliver services in a seamless manner to assist health workers situated anywhere to be accessed easily and access information which will help in service delivery. The proposed UCIC provides the most immersive Telepresence experience for one-to-one or many-tomany meetings. Extending to locations anywhere in the world, the transformative platform delivers Ultra-low operating costs through the use of general purpose networks and using special lenses and track systems.
Abstract: Analytical procedure was carried out in this paper to
calculate the ultimate load capacity of reinforced concrete corbels
strengthened or repaired externally with CFRP sheets. Strut and tie
method and shear friction method proposed earlier for analyzing
reinforced concrete corbels were modified to incorporate the effect of
external CFRP sheets bonded to the corbel. The points of weakness
of any method that lead to an inaccuracy, especially when
overestimating test results were checked and discussed. Comparison
of prediction with the test data indicates that the ratio of test /
calculated ultimate load is 0.82 and 1.17 using strut and tie method
and shear friction method, respectively. If the limits of maximum
shear stress is followed, the calculated ultimate load capacity using
shear friction method was found to underestimates test data
considerably.
Abstract: An additive fuzzy system comprising m rules with
n inputs and p outputs in each rule has at least t m(2n + 2 p + 1)
parameters needing to be tuned. The system consists of a large
number of if-then fuzzy rules and takes a long time to tune its
parameters especially in the case of a large amount of training data
samples. In this paper, a new learning strategy is investigated to cope
with this obstacle. Parameters that tend toward constant values at the
learning process are initially fixed and they are not tuned till the end
of the learning time. Experiments based on applications of the
additive fuzzy system in function approximation demonstrate that the
proposed approach reduces the learning time and hence improves
convergence speed considerably.
Abstract: This paper studies the dependability of componentbased
applications, especially embedded ones, from the diagnosis
point of view. The principle of the diagnosis technique is to
implement inter-component tests in order to detect and locate the
faulty components without redundancy. The proposed approach for
diagnosing faulty components consists of two main aspects. The first
one concerns the execution of the inter-component tests which
requires integrating test functionality within a component. This is the
subject of this paper. The second one is the diagnosis process itself
which consists of the analysis of inter-component test results to
determine the fault-state of the whole system. Advantage of this
diagnosis method when compared to classical redundancy faulttolerant
techniques are application autonomy, cost-effectiveness and
better usage of system resources. Such advantage is very important
for many systems and especially for embedded ones.
Abstract: In this paper, an automated algorithm to estimate and remove the continuous baseline from measured spectra containing both continuous and discontinuous bands is proposed. The algorithm uses previous information contained in a Continuous Database Spectra (CDBS) to obtain a linear basis, with minimum number of sampled vectors, capable of representing a continuous baseline. The proposed algorithm was tested by using a CDBS of flame spectra where Principal Components Analysis and Non-negative Matrix Factorization were used to obtain linear bases. Thus, the radical emissions of natural gas, oil and bio-oil flames spectra at different combustion conditions were obtained. In order to validate the performance in the baseline estimation process, the Goodness-of-fit Coefficient and the Root Mean-squared Error quality metrics were evaluated between the estimated and the real spectra in absence of discontinuous emission. The achieved results make the proposed method a key element in the development of automatic monitoring processes strategies involving discontinuous spectral bands.
Abstract: Sensor relocation is to repair coverage holes caused by node failures. One way to repair coverage holes is to find redundant nodes to replace faulty nodes. Most researches took a long time to find redundant nodes since they randomly scattered redundant nodes around the sensing field. To record the precise position of sensor nodes, most researches assumed that GPS was installed in sensor nodes. However, high costs and power-consumptions of GPS are heavy burdens for sensor nodes. Thus, we propose a fast sensor relocation algorithm to arrange redundant nodes to form redundant walls without GPS. Redundant walls are constructed in the position where the average distance to each sensor node is the shortest. Redundant walls can guide sensor nodes to find redundant nodes in the minimum time. Simulation results show that our algorithm can find the proper redundant node in the minimum time and reduce the relocation time with low message complexity.
Abstract: A long-term campaign for monitoring the
concentration of atmospheric Particulate Matter (PM) was conducted
at multiple sites located in the center and suburbs of the Tokyo
Metropolitan Area in Japan. The concentration of fine PM has shown a
declining trend over the last two decades. A positive matrix
factorization model elucidated that the contribution of combustion
sources was drastically reduced. In Japan, the regulations on vehicle
exhaust emissions were phased in and gradually tightened over the last
two decades, which has triggered a notable reduction in PM emissions
from automobiles and has contributed to the mitigation of the problem
of fine PM pollution.