Abstract: Partial oxidation (POX) of light hydrocarbons (e.g.
methane) is occurred in the first part of the autothermal reformer
(ATR). The results of the detailed modeling of the reformer based on
the thermodynamic model of the POX and 1D heterogeneous
catalytic model for the fixed bed section are considered here.
According to the results, the overall performance of the ATR can be
improved by changing the important feed parameters.
Abstract: In this paper the performance of unified power flow
controller is investigated in controlling the flow of po wer over the
transmission line. Voltage sources model is utilized to study the
behaviour of the UPFC in regulating the active, reactive power and
voltage profile. This model is incorporated in Newton Raphson
algorithm for load flow studies. Simultaneous method is employed
in which equations of UPFC and the power balance equations of
network are combined in to one set of non-linear algebraic equations.
It is solved according to the Newton raphson algorithm. Case studies
are carried on standard 5 bus network. Simulation is done in Matlab.
The result of network with and without using UPFC are compared in
terms of active and reactive power flows in the line and active and
reactive power flows at the bus to analyze the performance of UPFC.
Abstract: The quality of Ribbed Smoked Sheets
(RSS) primarily based on color, dryness, and the presence or
absence of fungus and bubbles. This quality is strongly
influenced by the drying and fumigation process namely
smoking process. Smoking that is held in high temperature
long time will result scorched dark brown sheets, whereas if
the temperature is too low or slow drying rate would resulted
in less mature sheets and growth of fungus. Therefore need to
find the time and temperature for optimum quality of sheets.
Enhance, unmonitored heat and mass transfer during smoking
process lead to high losses of energy balance. This research
aims to generate simple empirical mathematical model
describing the effect of smoking time and temperature to RSS
quality of color, water content, fungus and bubbles. The
second goal of study was to analyze energy balance during
smoking process. Experimental study was conducted by
measuring temperature, residence time and quality parameters
of 16 sheets sample in smoking rooms. Data for energy
consumption balance such as mass of fuel wood, mass of
sheets being smoked, construction temperature, ambient
temperature and relative humidity were taken directly along
the smoking process. It was found that mathematical model
correlating smoking temperature and time with color is Color
= -169 - 0.184 T4 - 0.193 T3 - 0.160 0.405 T1 + T2 + 0.388 t1
+3.11 t2 + 3.92t3 + 0.215 t4 with R square 50.8% and with
moisture is Moisture = -1.40-0.00123 T4 + 0.00032 T3 +
0.00260 T2 - 0.00292 T1 - 0.0105 t1 + 0.0290 t2 + 0.0452 t3
+ 0.00061 t4 with R square of 49.9%. Smoking room energy
analysis found useful energy was 27.8%. The energy stored in
the material construction 7.3%. Lost of energy in conversion
of wood combustion, ventilation and others were 16.6%. The
energy flowed out through the contact of material construction
with the ambient air was found to be the highest contribution
to energy losses, it reached 48.3%.
Abstract: In this paper, we are concerned with the design and
its simulation studies of a modified extremum seeking control for
nonlinear systems. A standard extremum seeking control has a simple
structure, but it takes a long time to reach an optimal operating point.
We consider a modification of the standard extremum seeking control
which is aimed to reach the optimal operating point more speedily
than the standard one. In the modification, PD acceleration term
is added before an integrator making a principal control, so that it
enables the objects to be regulated to the optimal point smoothly. This
proposed method is applied to Monod and Williams-Otto models to
investigate its effectiveness. Numerical simulation results show that
this modified method can improve the time response to the optimal
operating point more speedily than the standard one.
Abstract: This research was conducted in the Pua Watershed whereas located in the Upper Nan River Basin in Nan province, Thailand. Nan River basin originated in Nan province that comprises of many tributary streams to produce as inflow to the Sirikit dam provided huge reservoir with the storage capacity of 9510 million cubic meters. The common problems of most watersheds were found i.e. shortage water supply for consumption and agriculture utilizations, deteriorate of water quality, flood and landslide including debris flow, and unstable of riverbank. The Pua Watershed is one of several small river basins that flow through the Nan River Basin. The watershed includes 404 km2 representing the Pua District, the Upper Nan Basin, or the whole Nan River Basin, of 61.5%, 18.2% or 1.2% respectively. The Pua River is a main stream producing all year streamflow supplying the Pua District and an inflow to the Upper Nan Basin. Its length approximately 56.3 kilometers with an average slope of the channel by 1.9% measured. A diversion weir namely Pua weir bound the plain and mountainous areas with a very steep slope of the riverbed to 2.9% and drainage area of 149 km2 as upstream watershed while a mild slope of the riverbed to 0.2% found in a river reach of 20.3 km downstream of this weir, which considered as a gauged basin. However, the major branch streams of the Pua River are ungauged catchments namely: Nam Kwang and Nam Koon with the drainage area of 86 and 35 km2 respectively. These upstream watersheds produce runoff through the 3-streams downstream of Pua weir, Jao weir, and Kang weir, with an averaged annual runoff of 578 million cubic meters. They were analyzed using both statistical data at Pua weir and simulated data resulted from the hydrologic modeling system (HEC–HMS) which applied for the remaining ungauged basins. Since the Kwang and Koon catchments were limited with lack of hydrological data included streamflow and rainfall. Therefore, the mathematical modeling: HEC-HMS with the Snyder-s hydrograph synthesized and transposed methods were applied for those areas using calibrated hydrological parameters from the upstream of Pua weir with continuously daily recorded of streamflow and rainfall data during 2008-2011. The results showed that the simulated daily streamflow and sum up as annual runoff in 2008, 2010, and 2011 were fitted with observed annual runoff at Pua weir using the simple linear regression with the satisfied correlation R2 of 0.64, 062, and 0.59, respectively. The sensitivity of simulation results were come from difficulty using calibrated parameters i.e. lag-time, coefficient of peak flow, initial losses, uniform loss rates, and missing some daily observed data. These calibrated parameters were used to apply for the other 2-ungauged catchments and downstream catchments simulated.
Abstract: The self-organizing map (SOM) model is a well-known neural network model with wide spread of applications. The main characteristics of SOM are two-fold, namely dimension reduction and topology preservation. Using SOM, a high-dimensional data space will be mapped to some low-dimensional space. Meanwhile, the topological relations among data will be preserved. With such characteristics, the SOM was usually applied on data clustering and visualization tasks. However, the SOM has main disadvantage of the need to know the number and structure of neurons prior to training, which are difficult to be determined. Several schemes have been proposed to tackle such deficiency. Examples are growing/expandable SOM, hierarchical SOM, and growing hierarchical SOM. These schemes could dynamically expand the map, even generate hierarchical maps, during training. Encouraging results were reported. Basically, these schemes adapt the size and structure of the map according to the distribution of training data. That is, they are data-driven or dataoriented SOM schemes. In this work, a topic-oriented SOM scheme which is suitable for document clustering and organization will be developed. The proposed SOM will automatically adapt the number as well as the structure of the map according to identified topics. Unlike other data-oriented SOMs, our approach expands the map and generates the hierarchies both according to the topics and their characteristics of the neurons. The preliminary experiments give promising result and demonstrate the plausibility of the method.
Abstract: An adaptive spatial Gaussian mixture model is proposed for clustering based color image segmentation. A new clustering objective function which incorporates the spatial information is introduced in the Bayesian framework. The weighting parameter for controlling the importance of spatial information is made adaptive to the image content to augment the smoothness towards piecewisehomogeneous region and diminish the edge-blurring effect and hence the name adaptive spatial finite mixture model. The proposed approach is compared with the spatially variant finite mixture model for pixel labeling. The experimental results with synthetic and Berkeley dataset demonstrate that the proposed method is effective in improving the segmentation and it can be employed in different practical image content understanding applications.
Abstract: The study of the Andaman Sea can be studied by
using the oceanic model; therefore the grid covering the study area
should be generated. This research aims to generate grid covering
the Andaman Sea, situated between longitudes 90◦E to 101◦E and
latitudes 1◦N to 18◦N. A horizontal grid is an orthogonal curvilinear
with 87 × 217 grid points. The methods used in this study are
cubic spline and bilinear interpolations. The boundary grid points
are generated by spline interpolation while the interior grid points
have to be specified by bilinear interpolation method. A vertical grid
is sigma coordinate with 15 layers of water column.
Abstract: Explosive forming is one of the unconventional
techniques in which, most commonly, the water is used as the
pressure transmission medium. One of the newest methods in
explosive forming is gas detonation forming which uses a normal
shock wave derived of gas detonation, to form sheet metals. For this
purpose a detonation is developed from the reaction of H2+O2
mixture in a long cylindrical detonation tube. The detonation wave
goes through the detonation tube and acts as a blast load on the steel
blank and forms it. Experimental results are compared with a finite
element model; and the comparison of the experimental and
numerical results obtained from strain, thickness variation and
deformed geometry is carried out. Numerical and experimental
results showed approximately 75 – 90 % similarity in formability of
desired shape. Also optimum percent of gas mixture obtained when
we mix 68% H2 with 32% O2.
Abstract: This paper presents preliminary results on modeling
and control of a quadrotor UAV. With aerodynamic concepts, a
mathematical model is firstly proposed to describe the dynamics
of the quadrotor UAV. Parameters of this model are identified by
experiments with Matlab Identify Toolbox. A group of PID controllers
are then designed based on the developed model. To verify
the developed model and controllers, simulations and experiments for
altitude control, position control and trajectory tracking are carried
out. The results show that the quadrotor UAV well follows the
referenced commands, which clearly demonstrates the effectiveness
of the proposed approach.
Abstract: With rapid technology scaling, the proportion of the
static power consumption catches up with dynamic power
consumption gradually. To decrease leakage consumption is
becoming more and more important in low-power design. This paper
presents a power-gating scheme for P-DTGAL (p-type dual
transmission gate adiabatic logic) circuits to reduce leakage power
dissipations under deep submicron process. The energy dissipations of
P-DTGAL circuits with power-gating scheme are investigated in
different processes, frequencies and active ratios. BSIM4 model is
adopted to reflect the characteristics of the leakage currents. HSPICE
simulations show that the leakage loss is greatly reduced by using the
P-DTGAL with power-gating techniques.
Abstract: User-based Collaborative filtering (CF), one of the
most prevailing and efficient recommendation techniques, provides
personalized recommendations to users based on the opinions of other
users. Although the CF technique has been successfully applied in
various applications, it suffers from serious sparsity problems. The
cloud-model approach addresses the sparsity problems by
constructing the user-s global preference represented by a cloud
eigenvector. The user-based CF approach works well with dense
datasets while the cloud-model CF approach has a greater
performance when the dataset is sparse. In this paper, we present a
hybrid approach that integrates the predictions from both the
user-based CF and the cloud-model CF approaches. The experimental
results show that the proposed hybrid approach can ameliorate the
sparsity problem and provide an improved prediction quality.
Abstract: In North America, Most power distribution systems
employ a four-wire multi-grounded neutral (MGN) design. This paper has explained the inherent characteristics of multi-grounded three-phase four-wire distribution systems under unbalanced
situations. As a result, the mechanism of voltage swell and voltage sag in MGN feeders becomes difficult to understand. The simulation
tool that has been used in this paper is MATLAB under Windows software. In this paper the equivalent model of a full-scale multigrounded
distribution system implemented by MATLAB is
introduced. The results are expected to help utility engineers to understand the impact of MGN on distribution system operations.
Abstract: The Spiral development model has been used
successfully in many commercial systems and in a good number of
defense systems. This is due to the fact that cost-effective
incremental commitment of funds, via an analogy of the spiral model
to stud poker and also can be used to develop hardware or integrate
software, hardware, and systems. To support adaptive, semantic
collaboration between domain experts and knowledge engineers, a
new knowledge engineering process, called Spiral_OWL is proposed.
This model is based on the idea of iterative refinement, annotation
and structuring of knowledge base. The Spiral_OWL model is
generated base on spiral model and knowledge engineering
methodology. A central paradigm for Spiral_OWL model is the
concentration on risk-driven determination of knowledge engineering
process. The collaboration aspect comes into play during knowledge
acquisition and knowledge validation phase. Design rationales for the
Spiral_OWL model are to be easy-to-implement, well-organized, and
iterative development cycle as an expanding spiral.
Abstract: In mobile environments, unspecified numbers of transactions
arrive in continuous streams. To prove correctness of their
concurrent execution a method of modelling an infinite number of
transactions is needed. Standard database techniques model fixed
finite schedules of transactions. Lately, techniques based on temporal
logic have been proposed as suitable for modelling infinite schedules.
The drawback of these techniques is that proving the basic
serializability correctness condition is impractical, as encoding (the
absence of) conflict cyclicity within large sets of transactions results
in prohibitively large temporal logic formulae. In this paper, we show
that, under certain common assumptions on the graph structure of
data items accessed by the transactions, conflict cyclicity need only
be checked within all possible pairs of transactions. This results in
formulae of considerably reduced size in any temporal-logic-based
approach to proving serializability, and scales to arbitrary numbers
of transactions.
Abstract: This paper describes the speed sensorless vector control method of the parallel connected induction motor drive fed by a single inverter. Speed and rotor fluxes of the induction motor are estimated by natural observer with load torque adaptation and adaptive rotor flux observer. The performance parameters speed and rotor fluxes are estimated from the measured terminal voltages and currents. Fourth order induction motor model is used and speed is considered as a parameter. The performance of the natural observer is similar to the conventional observer. The speed of an induction motor is estimated by MATLAB simulation under different speed and load conditions. Estimated values along with other measured states are used for closed loop control. The simulation results show that the natural observer is also effective for parallel connected induction motor drive.
Abstract: This paper presents the design and implementation of
the WebGD, a CORBA-based document classification and retrieval
system on Internet. The WebGD makes use of such techniques as Web,
CORBA, Java, NLP, fuzzy technique, knowledge-based processing
and database technology. Unified classification and retrieval model,
classifying and retrieving with one reasoning engine and flexible
working mode configuration are some of its main features. The
architecture of WebGD, the unified classification and retrieval model,
the components of the WebGD server and the fuzzy inference engine
are discussed in this paper in detail.
Abstract: This paper describes an automatic algorithm to restore
the shape of three-dimensional (3D) left ventricle (LV) models created
from magnetic resonance imaging (MRI) data using a geometry-driven
optimization approach. Our basic premise is to restore the LV shape
such that the LV epicardial surface is smooth after the restoration. A
geometrical measure known as the Minimum Principle Curvature (κ2)
is used to assess the smoothness of the LV. This measure is used to
construct the objective function of a two-step optimization process.
The objective of the optimization is to achieve a smooth epicardial
shape by iterative in-plane translation of the MRI slices.
Quantitatively, this yields a minimum sum in terms of the magnitude
of κ
2, when κ2 is negative. A limited memory quasi-Newton algorithm,
L-BFGS-B, is used to solve the optimization problem. We tested our
algorithm on an in vitro theoretical LV model and 10 in vivo
patient-specific models which contain significant motion artifacts. The
results show that our method is able to automatically restore the shape
of LV models back to smoothness without altering the general shape of
the model. The magnitudes of in-plane translations are also consistent
with existing registration techniques and experimental findings.
Abstract: The statistical distributions are modeled in explaining
nature of various types of data sets. Although these distributions are
mostly uni-modal, it is quite common to see multiple modes in the
observed distribution of the underlying variables, which make the
precise modeling unrealistic. The observed data do not exhibit
smoothness not necessarily due to randomness, but could also be due
to non-randomness resulting in zigzag curves, oscillations, humps
etc. The present paper argues that trigonometric functions, which
have not been used in probability functions of distributions so far,
have the potential to take care of this, if incorporated in the
distribution appropriately. A simple distribution (named as, Sinoform
Distribution), involving trigonometric functions, is illustrated in the
paper with a data set. The importance of trigonometric functions is
demonstrated in the paper, which have the characteristics to make
statistical distributions exotic. It is possible to have multiple modes,
oscillations and zigzag curves in the density, which could be suitable
to explain the underlying nature of select data set.
Abstract: Model Predictive Control (MPC) is increasingly being
proposed for real time applications and embedded systems. However
comparing to PID controller, the implementation of the MPC in
miniaturized devices like Field Programmable Gate Arrays (FPGA)
and microcontrollers has historically been very small scale due to its
complexity in implementation and its computation time requirement.
At the same time, such embedded technologies have become an
enabler for future manufacturing enterprises as well as a transformer
of organizations and markets. Recently, advances in microelectronics
and software allow such technique to be implemented in embedded
systems. In this work, we take advantage of these recent advances
in this area in the deployment of one of the most studied and
applied control technique in the industrial engineering. In fact in
this paper, we propose an efficient framework for implementation
of Generalized Predictive Control (GPC) in the performed STM32
microcontroller. The STM32 keil starter kit based on a JTAG interface
and the STM32 board was used to implement the proposed GPC
firmware. Besides the GPC, the PID anti windup algorithm was
also implemented using Keil development tools designed for ARM
processor-based microcontroller devices and working with C/Cµ
langage. A performances comparison study was done between both
firmwares. This performances study show good execution speed and
low computational burden. These results encourage to develop simple
predictive algorithms to be programmed in industrial standard hardware.
The main features of the proposed framework are illustrated
through two examples and compared with the anti windup PID
controller.