Abstract: The use of titanium fluoride and iron fluoride
(TiF3/FeF3) catalysts in combination with polutetrafluoroethylene
(PTFE) in plain zinc- dialkyldithiophosphate (ZDDP) oil is important
for the study of engine tribocomponents and is increasingly a strategy
to improve the formation of tribofilm and provide low friction and
excellent wear protection in reduced phosphorus plain ZDDP oil. The
influence of surface roughness and the concentration of
TiF3/FeF3/PTFE were investigated using bearing steel samples
dipped in lubricant solution at 100°C for two different heating time
durations. This paper addresses the effects of water drop contact
angle using different surface; finishes after treating them with
different lubricant combination. The calculated water drop contact
angles were analyzed using Design of Experiment software (DOE)
and it was determined that a 0.05 μm Ra surface roughness would
provide an excellent TiF3/FeF3/PTFE coating for antiwear resistance
as reflected in the Scanning electron microscopy (SEM) images and
the tribological testing under extreme pressure conditions. Both
friction and wear performance depend greatly on the PTFE/and
catalysts in plain ZDDP oil with 0.05 % phosphorous and on the
surface finish of bearing steel. The friction and wear reducing effects,
which was observed in the tribological tests, indicated a better micro
lubrication effect of the 0.05 μm Ra surface roughness treated at
100°C for 24 hours when compared to the 0.1 μm Ra surface
roughness with the same treatment.
Abstract: Drying is a phenomenon that accompanies the
hardening of hydraulic materials. This study is concerned the
modelling of drying shrinkage of the hydraulic materials and the
prediction of the rate of spontaneous deformations of hydraulic
materials during hardening. The model developed takes consideration
of the main factors affecting drying shrinkage. There was agreement
between drying shrinkage predicted by the developed model and
experimental results. In last we show that developed model describe
the evolution of the drying shrinkage of high performances concretes
correctly.
Abstract: A lower consumption of thermal energy will
contribute not only to a reduction in the running costs, but also in the
reduction of pollutant emissions that contribute to the greenhouse
effect. Cogeneration or CHP (Combined Heat and Power) is the
system that produces power and usable heat simultaneously by
decreasing the pollutant emissions and increasing the efficiency.
Combined production of mechanical or electrical and thermal energy
using a simple energy source, such as oil, coal, natural or liquefied
gas, biomass or the sun; affords remarkable energy savings and
frequently makes it possible to operate with greater efficiency when
compared to a system producing heat and power separately. This
study aims to bring out the contributions of cogeneration systems to
the environment and sustainability by saving the energy and reducing
the emissions. In this way we made a comprehensive investigation in
the literature by focusing on the environmental aspects of the
cogeneration systems. In the light of these studies we reached that,
cogeneration systems must be consider in sustainability and their
benefits on protecting the ecology must be investigated.
Abstract: Workflow scheduling is an important part of cloud
computing and based on different criteria it decides cost, execution
time, and performances. A cloud workflow system is a platform
service facilitating automation of distributed applications based on
new cloud infrastructure. An aspect which differentiates cloud
workflow system from others is market-oriented business model, an
innovation which challenges conventional workflow scheduling
strategies. Time and Cost optimization algorithm for scheduling
Hybrid Clouds (TCHC) algorithm decides which resource should be
chartered from public providers is combined with a new De-De
algorithm considering that every instance of single and multiple
workflows work without deadlocks. To offset this, two new concepts
- De-De Dodging Algorithm and Priority Based Decisive Algorithm -
combine with conventional deadlock avoidance issues by proposing
one algorithm that maximizes active (not just allocated) resource use
and reduces Makespan.
Abstract: A novel chromium-free protective coating films based
on a zeolite coating was growing onto a FeCrAlloy metal using in –
situ hydrothermal method. The zeolite film was obtained using in-situ
crystallization process that is capable of coating large surfaces with
complex shape and in confined spaces has been developed. The
zeolite coating offers an advantage of a high mechanical stability and
thermal stability. The physicochemical properties were investigated
using X-ray diffraction (XRD), Electron Microscopy (SEM), Energy
Dispersive X–ray Analysis (EDX) and Thermogravimetric Analysis
(TGA). The transition from oxide-on-alloy wires to hydrothermally
synthesised uniformly zeolite coated surfaces was followed using
SEM and XRD. In addition, the robustness of the prepared coating
was confirmed by subjecting these to thermal cycling (ambient to
550oC).
Abstract: In this paper, the secure BioSemantic Scheme is
presented to bridge biological/biomedical research problems and
computational solutions via semantic computing. Due to the diversity
of problems in various research fields, the semantic capability
description language (SCDL) plays and important role as a common
language and generic form for problem formalization. SCDL is
expected the essential for future semantic and logical computing in
Biosemantic field. We show several example to Biomedical problems
in this paper. Moreover, in the coming age of cloud computing, the
security problem is considered to be crucial issue and we presented a
practical scheme to cope with this problem.
Abstract: Grains, including oats (Avena sativa L.), have been
recognized functional foods, because provide beneficial effect on the
health of the consumer and decrease the risk of various diseases. Oats
are good source of soluble fibre, essential amino acids, unsaturated
fatty acids, vitamins and minerals. Oat breeders have developed oat
varieties and improved yielding ability potential of oat varieties.
Therefore, the aim of investigation was to analyze the composition of
perspective oat varieties and breeding lines grains grown in different
conditions and evaluate functional properties. In the studied samples
content of protein, starch, β-glucans, total dietetic fibre, composition
of amino acids and vitamin E were determined. The results of
analysis showed that protein content depending of varieties ranged
9.70% to 17.30% total dietary fibre 13.66 g100g-1 to 30.17 g100g-1,
content of β-glucans 2.7 g100g-1 to 3.5 g100g-1, amount of
vitamin E (α-tocopherol) determined from 4 mgkg-1 to 9.9 mgkg-1.
The sums of essential amino acids in oat grain samples were
determined from 31.63 gkg-1 to 54.90 gkg-1. It is concluded that
amino acids composition of husked and naked oats grown in organic
or conventional conditions is close to optimal for human health.
Abstract: The objective of the study is to assess the
implementation of LED lighting into forest machine work in the dark.
In addition, the paper includes a wide variety of important and
relevant safety and health parameters. In modern, computerized work
in the cab of forest machines, artificial illumination is a demanding
task when performing duties, such as the visual inspections of wood
and computer calculations. We interviewed entrepreneurs and
gathered the following as the most pertinent themes: (1) safety, (2)
practical problems, and (3) work with LED lighting. The most
important comments were in regards to the practical problems of
LED lighting. We found indications of technical problems in
implementing LED lighting, like snow and dirt on the surfaces of
lamps that dim the emission of light. Moreover, service work in the
dark forest is dangerous and increases the risks of on-site accidents.
We also concluded that the amount of blue light to the eyes should be
assessed, especially, when the drivers are working in a semi-dark cab.
Abstract: Nine Degrees of Freedom (9 DOF) systems are
already in development in many areas. In this paper, an integrated
pressure sensor is proposed that will make use of an already existing
monolithic 9 DOF inertial MEMS platform. Capacitive pressure
sensors can suffer from limited sensitivity for a given size of
membrane. This novel pressure sensor design increases the sensitivity
by over 5 times compared to a traditional array of square diaphragms
while still fitting within a 2 mm x 2 mm chip and maintaining a fixed
static capacitance. The improved design uses one large diaphragm
supported by pillars with fixed electrodes placed above the areas of
maximum deflection. The design optimization increases the
sensitivity from 0.22 fF/kPa to 1.16 fF/kPa. Temperature sensitivity
was also examined through simulation.
Abstract: This paper presents thermal annealing de-wetting
technique for the preparation of porous metal membrane for Thin
Film Encapsulation (TFE) application. Thermal annealing de-wetting
experimental results reveal that pore size formation in porous metal
membrane depend upon i.e. 1. The substrate at which metal is
deposited, 2. Melting point of metal used for porous metal cap layer
membrane formation, 3. Thickness of metal used for cap layer, 4.
Temperature used for formation of porous metal membrane. In order
to demonstrate this technique, Silver (Ag) was used as a metal for
preparation of porous metal membrane on amorphous silicon (a-Si)
and silicon oxide. The annealing of the silver thin film of various
thicknesses was performed at different temperature. Pores in porous
silver film were analyzed using Scanning Electron Microscope
(SEM). In order to check the usefulness of porous metal film for TFE
application, the porous silver film prepared on amorphous silicon (a-
Si) and silicon oxide was released using XeF2 and VHF, respectively.
Finally, guide line and structures are suggested to use this porous
membrane for robust TFE application.
Abstract: The aim of the present study is to investigate
consumers' determinants of intention toward the adoption of Smart
Grid solutions and technologies. Ajzen's Theory of Planned
Behaviour (TPB) model is applied and tested to explain the formation
of such adoption intention. An exogenous variable, taking into
account the resistance to change of individuals, was added to the
basic model. The elicitation study allowed obtaining salient modal
beliefs, which were used, with the support of literature, to design the
questionnaire. After the screening phase, data collected from the
main survey were analysed for evaluating measurement model's
reliability and validity. Consistent with the theory, the results of
structural equation analysis revealed that attitude, subjective norm,
and perceived behavioural control positively, which affected the
adoption intention. Specifically, the variable with the highest estimate
loading factor was found to be the perceived behavioural control,
and, the most important belief related to each construct was
determined (e.g., energy saving was observed to be the most
significant belief linked with attitude). Further investigation indicated
that the added exogenous variable has a negative influence on
intention; this finding confirmed partially the hypothesis, since this
influence was indirect: such relationship was mediated by attitude.
Implications and suggestions for future research are discussed.
Abstract: Chalcopyrite (CuFeS2) is the most common primary
mineral used for the commercial production of copper. The low
dissolution efficiency of chalcopyrite in sulfate media has prevented
an efficient industrial leaching of this mineral in sulfate media. Ferric
ions, bacteria, oxygen and other oxidants have been used as oxidizing
agents in the leaching of chalcopyrite in sulfate and chloride media
under atmospheric or pressure leaching conditions. Two leaching
methods were studied to evaluate chalcopyrite (CuFeS2) dissolution
in acid media. First, the conventional oxidative acid leaching method
was carried out using sulfuric acid (H2SO4) and potassium
dichromate (K2Cr2O7) as oxidant at atmospheric pressure. Second,
microwave-assisted acid leaching was performed using the
microwave accelerated reaction system (MARS) for same reaction
media. Parameters affecting the copper extraction such as leaching
time, leaching temperature, concentration of H2SO4 and
concentration of K2Cr2O7 were investigated. The results of
conventional acid leaching experiments were compared to the
microwave leaching method. It was found that the copper extraction
obtained under high temperature and high concentrations of oxidant
with microwave leaching is higher than those obtained
conventionally. 81% copper extraction was obtained by the
conventional oxidative acid leaching method in 180 min, with the
concentration of 0.3 mol/L K2Cr2O7 in 0.5M H2SO4 at 50 ºC, while
93.5% copper extraction was obtained in 60 min with microwave
leaching method under same conditions.
Abstract: The purpose of this project is to propose a quick and
environmentally friendly alternative to measure the quality of oils
used in food industry. There is evidence that repeated and
indiscriminate use of oils in food processing cause physicochemical
changes with formation of potentially toxic compounds that can
affect the health of consumers and cause organoleptic changes. In
order to assess the quality of oils, non-destructive optical techniques
such as Interferometry offer a rapid alternative to the use of reagents,
using only the interaction of light on the oil. Through this project, we
used interferograms of samples of oil placed under different heating
conditions to establish the changes in their quality. These
interferograms were obtained by means of a Mach-Zehnder
Interferometer using a beam of light from a HeNe laser of 10mW at
632.8nm. Each interferogram was captured, analyzed and measured
full width at half-maximum (FWHM) using the software from
Amcap and ImageJ. The total of FWHMs was organized in three
groups. It was observed that the average obtained from each of the
FWHMs of group A shows a behavior that is almost linear, therefore
it is probable that the exposure time is not relevant when the oil is
kept under constant temperature. Group B exhibits a slight
exponential model when temperature raises between 373 K and 393
K. Results of the t-Student show a probability of 95% (0.05) of the
existence of variation in the molecular composition of both samples.
Furthermore, we found a correlation between the Iodine Indexes
(Physicochemical Analysis) and the Interferograms (Optical
Analysis) of group C. Based on these results, this project highlights
the importance of the quality of the oils used in food industry and
shows how Interferometry can be a useful tool for this purpose.
Abstract: HR is a department that enhances the power of
employee performance in regard with their services, and to make the
organization strategic objectives. The main concern of HR
department is to organize people, focus on policies and their system.
The empirical study shows the relationship between HRM (Human
Resource Management practices) and their Job Satisfaction. The
Hypothesis is testing on a sample of overall 320 employees of 5
different Pharmaceutical departments of different organizations in
Pakistan. The important thing as Relationship of Job satisfaction with
HR Practices, Impact on Job Satisfaction with HR Practices,
Participation of Staff of Different Departments, HR Practices effects
the Job satisfaction, Recruitment or Hiring and Selection effects the
Job satisfaction, Training and Development, Performance and
Appraisals, Compensation affects the Job satisfaction , and Industrial
Relationships affects the Job satisfaction. After finishing all data
analysis, the conclusion is that lots of Job related activities raise the
confidence of Job satisfaction of employees with their salary and
other benefits.
Abstract: This article presents a vibration diagnostic method
designed for Permanent Magnets (PM) electrical machines–traction
motors and generators. Those machines are commonly used in traction
drives of electrical vehicles and small wind or water systems. The
described method is very innovative and unique. Specific structural
properties of machines excited by permanent magnets are used in this
method - electromotive force (EMF) generated due to vibrations. There
was analyzed number of publications, which describe vibration
diagnostic methods, and tests of electrical machines and there was no
method found to determine the technical condition of such machine
basing on their own signals. This work presents field-circuit model,
results of static tests, results of calculations and simulations.
Abstract: Biodiesel is one of the alternative fuels that promising
for substituting petro diesel as energy source which is advantage on
sustainability and ecofriendly. Due to the raw material that tend to
decompose during storage, biodiesel also have the same characteristic
that tend to decompose and formed higher acid value which is the
result of oxidation to double bond on a chain of ester. Decomposition of biodiesel due to oxidation reaction could
prevent by introduce a small amount of antioxidant. The origin of raw
materials and the process for producing biodiesel will determine the
effectiveness of antioxidant. The quality degradation on biodiesel
could evaluate by measuring iodine value and acid number of
biodiesel. Biodiesel made from high fatty acid Jatropha curcas oil by using
esterification and transesterification process will stand on the quality
by introduce 90 ppm pyrogallol powder on the biodiesel, which could
increase Induction period time from 2 hours to more than 6 hours in
rancimat test evaluation.
Abstract: In this paper, we provided a literature survey on the
artificial stock problem (ASM). The paper began by exploring the
complexity of the stock market and the needs for ASM. ASM
aims to investigate the link between individual behaviors (micro
level) and financial market dynamics (macro level). The variety of
patterns at the macro level is a function of the AFM complexity. The
financial market system is a complex system where the relationship
between the micro and macro level cannot be captured analytically.
Computational approaches, such as simulation, are expected to
comprehend this connection. Agent-based simulation is a simulation
technique commonly used to build AFMs. The paper proceeds by
discussing the components of the ASM. We consider the roles
of behavioral finance (BF) alongside the traditionally risk-averse
assumption in the construction of agent’s attributes. Also, the
influence of social networks in the developing of agents interactions is
addressed. Network topologies such as a small world, distance-based,
and scale-free networks may be utilized to outline economic
collaborations. In addition, the primary methods for developing
agents learning and adaptive abilities have been summarized.
These incorporated approach such as Genetic Algorithm, Genetic
Programming, Artificial neural network and Reinforcement Learning.
In addition, the most common statistical properties (the stylized facts)
of stock that are used for calibration and validation of ASM are
discussed. Besides, we have reviewed the major related previous
studies and categorize the utilized approaches as a part of these
studies. Finally, research directions and potential research questions
are argued. The research directions of ASM may focus on the macro
level by analyzing the market dynamic or on the micro level by
investigating the wealth distributions of the agents.
Abstract: Bloom’s Taxonomy has been changed during the
years. The idea of this writing is about the revision that has happened
in both facts and terms. It also contains case studies of using
cognitive Bloom’s taxonomy in teaching geometric solids to the
secondary school students, affective objectives in a creative
workshop for adults and psychomotor objectives in fixing a
malfunctioned refrigerator lamp. There is also pointed to the
important role of classification objectives in adult education as a way
to prevent memory loss.
Abstract: The development of electric vehicle batteries have
resulted in very high energy density lithium-ion batteries. However,
this progress is accompanied by the risk of thermal runaway, which
can result in serious accidents. Heat pipes are heat exchangers that
are suitable to be applied in electric vehicle battery thermal
management for their lightweight, compact size and do not require
external power supply. This paper aims to examine experimentally a
Flat Plate Loop Heat Pipe (FPLHP) performance as a heat exchanger
in thermal management system of lithium-ion battery for electric
vehicle application. The heat generation of the battery was simulated
using a cartridge heater. Stainless steel screen mesh was used as the
capillary wick. Distilled water, alcohol and acetone were used as
working fluids with a filling ratio of 60%. It was found that acetone
gives the best performance that produces thermal resistance of 0.22
W/°C with 50°C evaporator temperature at heat flux load of 1.61
W/cm2.
Abstract: Currently there are many use of threaded reinforcing
bars in construction fields because those do not need additional screw
processing when connecting reinforcing bar by threaded coupler. In
this study, reinforced concrete bridge piers using threaded rebar
coupler system at the plastic hinge area were tested to evaluate seismic
performance. The test results showed that threads of the threaded rebar
coupler system could be loosened while under tension-compression
cyclic loading because tolerance and rib face angle of a threaded rebar
coupler system are greater than that of a conventional ribbed rebar
coupler system. As a result, cracks were concentrated just outside of
the mechanical coupler and stiffness of reinforced concrete bridge pier
decreased. Therefore, it is recommended that connection ratio of
mechanical couplers in one section shall be below 50% in order that
cracks are not concentrated just outside of the mechanical coupler.
Also, reduced stiffness of the specimen should be considered when
using the threaded rebar coupler system.