Abstract: In-situ chemical oxidation (ISCO) has been widely
used for source zone remediation of Dense Nonaqueous Phase
Liquids (DNAPLs) in subsurface environments. DNAPL source
zones for karst aquifers are generally located in epikarst where the
DNAPL mass is trapped either in karst soil or at the regolith contact
with carbonate bedrock. This study aims to investigate the
performance of oxidation of residual trichloroethylene found in such
environments by potassium permanganate. Batch and flow cell
experiments were conducted to determine the kinetics and the mass
removal rate of TCE. pH change, Cl production, TCE and MnO4
destruction were monitored routinely during experiments. Nonreactive
tracer tests were also conducted prior and after the oxidation
process to determine the influence of oxidation on flow conditions.
The results show that oxidant consumption rate of the calcareous
epikarst soil was significant and the oxidant demand was determined
to be 20 g KMnO4/kg soil. Oxidation rate of residual TCE (1.26x10-3
s-1) was faster than the oxidant consumption rate of the soil (2.54 -
2.92x10-4 s-1) at only high oxidant concentrations (> 40 mM
KMnO4). Half life of TCE oxidation ranged from 7.9 to 10.7 min.
Although highly significant fraction of residual TCE mass in the
system was destroyed by permanganate oxidation, TCE
concentration in the effluent remained above its MCL. Flow
interruption tests indicate that efficiency of ISCO was limited by the
rate of TCE dissolution and the rate-limited desorption of TCE. The
residence time and the initial concentration of the oxidant in the
source zone also controlled the efficiency of ISCO in epikarst.
Abstract: Time-Cost Optimization "TCO" is one of the greatest challenges in construction project planning and control, since the optimization of either time or cost, would usually be at the expense of the other. Since there is a hidden trade-off relationship between project and cost, it might be difficult to predict whether the total cost would increase or decrease as a result of the schedule compression. Recently third dimension in trade-off analysis is taken into consideration that is quality of the projects. Few of the existing algorithms are applied in a case of construction project with threedimensional trade-off analysis, Time-Cost-Quality relationships. The objective of this paper is to presents the development of a practical software system; that named Automatic Multi-objective Typical Construction Resource Optimization System "AMTCROS". This system incorporates the basic concepts of Line Of Balance "LOB" and Critical Path Method "CPM" in a multi-objective Genetic Algorithms "GAs" model. The main objective of this system is to provide a practical support for typical construction planners who need to optimize resource utilization in order to minimize project cost and duration while maximizing its quality simultaneously. The application of these research developments in planning the typical construction projects holds a strong promise to: 1) Increase the efficiency of resource use in typical construction projects; 2) Reduce construction duration period; 3) Minimize construction cost (direct cost plus indirect cost); and 4) Improve the quality of newly construction projects. A general description of the proposed software for the Time-Cost-Quality Trade-Off "TCQTO" is presented. The main inputs and outputs of the proposed software are outlined. The main subroutines and the inference engine of this software are detailed. The complexity analysis of the software is discussed. In addition, the verification, and complexity of the proposed software are proved and tested using a real case study.
Abstract: In this paper, we present some new upper bounds for
the spectral radius of iterative matrices based on the concept of
doubly α diagonally dominant matrix. And subsequently, we give
two examples to show that our results are better than the earlier ones.
Abstract: Yogyakarta, as the capital city of Yogyakarta Province, has important roles in various sectors that require good provision of public transportation system. Ideally, a good transportation system should be able to accommodate the amount of travel demand. This research attempts to develop a trip generation model to predict the number of public transport passenger in Yogyakarta city. The model is built by using multiple linear regression analysis, which establishes relationship between trip number and socioeconomic attributes. The data consist of primary and secondary data. Primary data was collected by conducting household surveys which randomly selected. The resulted model is further applied to evaluate the existing TransJogja, a new Bus Rapid Transit system serves Yogyakarta and surrounding cities, shelters.
Abstract: To enhance installation security, a LNG storage in Rudong of Jiangsu province was adopted as a practical work, and it was analyzed by nonlinear finite element method to research overall and local stability performance, as well as the stress and deformation under the action of wind load and self-weight. Results indicate that deformation is tiny when steel mesh maintains as an overall ring, and stress caused by vertical bending moment and tension of bottom tie wire are also in the safe range. However, axial forces of lap reinforcement in adjacent steel mesh exceed the ultimate bearing capacity of tie wire. Hence, tie wires are ruptured; single mesh loses lateral connection and turns into monolithic status as the destruction of overall structure. Further more, monolithic steel mesh is led to collapse by the damage of bottom connection. So, in order to prevent connection failure and enhance installation security, the overlapping parts of steel mesh should be taken more reliable measures.
Abstract: As the advancement of technology, online shopping channel develops rapidly in recent years. According to the report of Taiwan Network Information Center, there are almost eighty percents of internet population shopping in online channel. Synthesizing insights from the previous research, this study develops the conceptual model to integrate Theory of Perceived Risk (TPR) and Technology Acceptance Model (TAM) to apply in online shopping. Using data collected from 637 respondents from online survey website, we use structural equation modeling to test measurement and structural models. The results suggest the need for consideration of perceived risk as an antecedent in the Technology Acceptance Model. The limitations and implications are discussed.
Abstract: This study aims to assess the potential of solar energy technology for improving access to water and hence the livelihood strategies of rural communities in Baja California Sur, Mexico. It focuses on livestock ranches and photovoltaic water-pumptechnology as well as other water extraction methods. The methodology used are the Sustainable Livelihoods and the Appropriate Technology approaches. A household survey was applied in June of 2006 to 32 ranches in the municipality, of which 22 used PV pumps; and semi-structured interviews were conducted. Findings indicate that solar pumps have in fact helped people improve their quality of life by allowing them to pursue a different livelihood strategy and that improved access to water -not necessarily as more water but as less effort to extract and collect it- does not automatically imply overexploitation of the resource; consumption is based on basic needs as well as on storage and pumping capacity. Justification for such systems lies in the avoidance of logistical problems associated to fossil fuels, PV pumps proved to be the most beneficial when substituting gasoline or diesel equipment but of dubious advantage if intended to replace wind or gravity systems. Solar water pumping technology-s main obstacle to dissemination are high investment and repairs costs and it is therefore not suitable for all cases even when insolation rates and water availability are adequate. In cases where affordability is not an obstacle it has become an important asset that contributes –by means of reduced expenses, less effort and saved time- to the improvement of livestock, the main livelihood provider for these ranches.
Abstract: The stop watch is used to measure the time required
for a certain event. This is different from normal clocks in many
ways, one of which is the accuracy of time. The stop watch requires
much more accuracy than the normal clocks. In this paper, an
ATmega8535 microcontroller was used to control the stop watch, by
which perfect accuracy can be ensured. For compiling the C code and
for loading the compiled .hex file into the microcontroller, AVR
studio and PonyProg were used respectively. The stop watch is also
different from traditional stop watches, as it contains two different
timing modes namely 'Split timing' and 'Lap timing'.
Abstract: RFID system, in which we give identification number to each item and detect it with radio frequency, supports more variable service than barcode system can do. For example, a refrigerator with RFID reader and internet connection will automatically notify expiration of food validity to us. But, in spite of its convenience, RFID system has some security threats, because anybody can get ID information of item easily. One of most critical threats is privacy invasion. Existing privacy protection schemes or systems have been proposed, and these schemes or systems defend normal users from attempts that any attacker tries to get information using RFID tag value. But, these systems still have weakness that attacker can get information using analogous value instead of original tag value. In this paper, we mention this type of attack more precisely and suggest 'Tag Broker Model', which can defend it. Tag broker in this model translates original tag value to random value, and user can only get random value. Attacker can not use analogous tag value, because he/she is not able to know original one from it.
Abstract: This research is aimed at studying the nature of
problems and demands of the training for community leaders in the
upper northeastern region of Thailand. Population and group
samplings are based on 360 community leaders in the region who
have experienced prior training from the Udonthani Rajabhat
University. Stratified random samplings have been drawn upon 186
participants. The research tools is questionnaires. The frequency,
percentage and standard deviation are employed in data analysis. The
findings indicate that most of community leaders are males and
senior adults. The problems in training are associated with the
inconveniences of long-distance travelling to training locations,
inadequacy of learning centers and training sites and high training
costs. The demand of training is basically motivated by a desire for
self-development in modern knowledge in keeping up-to-date with
the changing world and the need for technological application and
facilitation in shortening the distance to training locations and in
limiting expensive training costs.
Abstract: Public procurement is one of the most
important areas in the public sector that introduces a possibility for a
corruption. Due to the volume of the funds that are
allocated through this institution (in the EU countries it is between 10
– 15% of GDP), it has very serious implications for the efficiency of
public expenditures and the overall economic efficiency as
well. Indicators that are usually used for the measurement of the
corruption (such as Corruption Perceptions Index - CPI) show that
the worst situation is in the post-communist countries
and Mediterranean countries.
The presented paper uses the Czech Republic as an example of a
post-communist country and analyses the factors which influence
the scope of corruption in public procurement. Moreover, the
paper discusses indicators that could point at the public procurement
market inefficiency. The presented results show that post-communist
states use the institute of public contracts significantly more than the
old member countries of the continental Europe. It has a very
important implication because it gives more space for corruption.
Furthermore, it appears that the inefficient functioning of public
procurement market is clearly manifested in the low number of bids,
low level of market transparency and an ineffective control
system. Some of the observed indicators are statistically significantly
correlated with the CPI.
Abstract: A numerical study has been conducted to investigate the influence of fin pitch and relative humidity on the heat transfer performance of the fin-and-tube heat exchangers having plain fin geometry under dehumidifying conditions. The analysis is done using the ratio between the heat transfer coefficients in totally wet conditions and those in totally dry conditions using the appropriate correlations for both dry and wet conditions. For a constant relative humidity, it is found that the heat transfer coefficient increases with the increase of the air frontal velocity. By contrast, the fin efficiency decreases when the face velocity is increased. Apparently, this phenomenon is attributed to the path of condensate drainage. For the influence of relative humidity, the results showed an increase in heat transfer performance and a decrease in wet fin efficiency when relative humidity increases. This is due to the higher amount of mass transfer encountered at higher relative humidity. However, it is found that the effect of fin pitch on the heat transfer performance depends strongly on the face velocity. At lower frontal velocity the heat transfer increases with fin pitch. Conversely, an increase in fin pitch gives lower heat transfer coefficients when air velocity is increased.
Abstract: In this paper, we validate crater detection in moon surface image using FLDA. This proposal assumes that it is applied to SLIM (Smart Lander for Investigating Moon) project aiming at the pin-point landing to the moon surface. The point where the lander should land is judged by the position relations of the craters obtained via camera, so the real-time image processing becomes important element. Besides, in the SLIM project, 400kg-class lander is assumed, therefore, high-performance computers for image processing cannot be equipped. We are studying various crater detection methods such as Haar-Like features, LBP, and PCA. And we think these methods are appropriate to the project, however, to identify the unlearned images obtained by actual is insufficient. In this paper, we examine the crater detection using FLDA, and compare with the conventional methods.
Abstract: This paper features the trajectory planning design of a indigenously developed 4-Axis SCARA robot which is used for doing successful robotic manipulation task in the laboratory. Once, a trajectory is being designed and given as input to the robot, the robot's gripper tip moves along that specified trajectory. Trajectories have to be designed in the work space only. The main idea of this paper is to design a continuous path trajectory model for the indigenously developed SCARA robot arm during its maneuvering from one point to another point (during pick and place operations) in a workspace avoiding all the obstacles in its path of motion.
Abstract: A new and cost effective RP-HPLC method was
developed and validated for simultaneous analysis of non steroidal
anti inflammatory dugs Diclofenac sodium (DFS), Flurbiprofen
(FLP) and an opioid analgesic Tramadol (TMD) in advanced drug
delivery systems (Liposome and Microcapsules), marketed brands
and human plasma. Isocratic system was employed for the flow of
mobile phase consisting of 10 mM sodium dihydrogen phosphate
buffer and acetonitrile in molar ratio of 67: 33 with adjusted pH of
3.2. The stationary phase was hypersil ODS column (C18, 250×4.6
mm i.d., 5 μm) with controlled temperature of 30 C°. DFS in
liposomes, microcapsules and marketed drug products was
determined in range of 99.76-99.84%. FLP and TMD in
microcapsules and brands formulation were 99.78 - 99.94 % and
99.80 - 99.82 %, respectively. Single step liquid-liquid extraction
procedure using combination of acetonitrile and trichloroacetic acid
(TCA) as protein precipitating agent was employed. The detection
limits (at S/N ratio 3) of quality control solutions and plasma samples
were 10, 20, and 20 ng/ml for DFS, FLP and TMD, respectively.
The Assay was acceptable in linear dynamic range. All other
validation parameters were found in limits of FDA and ICH method
validation guidelines. The proposed method is sensitive, accurate and
precise and could be applicable for routine analysis in
pharmaceutical industry as well as in human plasma samples for
bioequivalence and pharmacokinetics studies.
Abstract: Web-based systems have become increasingly
important due to the fact that the Internet and the World Wide Web
have become ubiquitous, surpassing all other technological
developments in our history. The Internet and especially companies
websites has rapidly evolved in their scope and extent of use, from
being a little more than fixed advertising material, i.e. a "web
presences", which had no particular influence for the company's
business, to being one of the most essential parts of the company's
core business.
Traditional software engineering approaches with process models
such as, for example, CMM and Waterfall models, do not work very
well since web system development differs from traditional
development. The development differs in several ways, for example,
there is a large gap between traditional software engineering designs
and concepts and the low-level implementation model, many of the
web based system development activities are business oriented (for
example web application are sales-oriented, web application and
intranets are content-oriented) and not engineering-oriented.
This paper aims to introduce Increment Iterative extreme
Programming (IIXP) methodology for developing web based
systems. In difference to the other existence methodologies, this
methodology is combination of different traditional and modern
software engineering and web engineering principles.
Abstract: We present a preliminary x-ray study on human-hair
microstructures for a health-state indicator, in particular a cancer
case. As an uncomplicated and low-cost method of x-ray technique,
the human-hair microstructure was analyzed by wide-angle x-ray
diffractions (XRD) and small-angle x-ray scattering (SAXS). The
XRD measurements exhibited the simply reflections at the d-spacing
of 28 Å, 9.4 Å and 4.4 Å representing to the periodic distance of the
protein matrix of the human-hair macrofibrous and the diameter and
the repeated spacing of the polypeptide alpha helixes of the
photofibrils of the human-hair microfibrous, respectively. When
compared to the normal cases, the unhealthy cases including to the
breast- and ovarian-cancer cases obtained higher normalized ratios of
the x-ray diffracting peaks of 9.4 Å and 4.4 Å. This likely resulted
from the varied distributions of microstructures by a molecular
alteration. As an elemental analysis by x-ray fluorescence (XRF), the
normalized quantitative ratios of zinc(Zn)/calcium(Ca) and
iron(Fe)/calcium(Ca) were determined. Analogously, both Zn/Ca and
Fe/Ca ratios of the unhealthy cases were obtained higher than both of
the normal cases were. Combining the structural analysis by XRD
measurements and the elemental analysis by XRF measurements
exhibited that the modified fibrous microstructures of hair samples
were in relation to their altered elemental compositions. Therefore,
these microstructural and elemental analyses of hair samples will be
benefit to associate with a diagnosis of cancer and genetic diseases.
This functional method would lower a risk of such diseases by the
early diagnosis. However, the high-intensity x-ray source, the highresolution
x-ray detector, and more hair samples are necessarily
desired to develop this x-ray technique and the efficiency would be
enhanced by including the skin and fingernail samples with the
human-hair analysis.
Abstract: The paper presents an on-line recognition machine
(RM) for continuous/isolated, dynamic and static gestures that arise
in Flight Deck Officer (FDO) training. RM is based on generic pattern
recognition framework. Gestures are represented as templates using
summary statistics. The proposed recognition algorithm exploits temporal
and spatial characteristics of gestures via dynamic programming
and Markovian process. The algorithm predicts corresponding index
of incremental input data in the templates in an on-line mode.
Accumulated consistency in the sequence of prediction provides a
similarity measurement (Score) between input data and the templates.
The algorithm provides an intuitive mechanism for automatic detection
of start/end frames of continuous gestures. In the present paper,
we consider isolated gestures. The performance of RM is evaluated
using four datasets - artificial (W TTest), hand motion (Yang) and
FDO (tracker, vision-based ). RM achieves comparable results which
are in agreement with other on-line and off-line algorithms such as
hidden Markov model (HMM) and dynamic time warping (DTW).
The proposed algorithm has the additional advantage of providing
timely feedback for training purposes.
Abstract: Prediction of sinusoidal signals with time-varying
frequencies has been an important research topic in power electronics
systems. To solve this problem, we propose a new fuzzy
predictive filtering scheme, which is based on a Finite Impulse
Response (FIR) filter bank. Fuzzy logic is introduced here to provide
appropriate interpolation of individual filter outputs. Therefore,
instead of regular 'hard' switching, our method has the advantageous
'soft' switching among different filters. Simulation
comparisons between the fuzzy predictive filtering and conventional
filter bank-based approach are made to demonstrate that the
new scheme can achieve an enhanced prediction performance for
slowly changing sinusoidal input signals.
Abstract: The problem of N cracks interaction in an isotropic
elastic solid is decomposed into a subproblem of a homogeneous solid
without crack and N subproblems with each having a single crack
subjected to unknown tractions on the two crack faces. The unknown
tractions, namely pseudo tractions on each crack are expanded into
polynomials with unknown coefficients, which have to be determined
by the consistency condition, i.e. by the equivalence of the original
multiple cracks interaction problem and the superposition of the N+1
subproblems. In this paper, Kachanov-s approach of average tractions
is extended into the method of moments to approximately impose the
consistence condition. Hence Kachanov-s method can be viewed as
the zero-order method of moments. Numerical results of the stress
intensity factors are presented for interactions of two collinear cracks,
three collinear cracks, two parallel cracks, and three parallel cracks.
As the order of moment increases, the accuracy of the method of
moments improves.